Linux issues on Xilinx XUPV2P board
Hi,
I have tried running the Linux 2.6.24 and Linux 2.6.26 kernels from git.xilinx.com on the Xilinx XUPV2P board but have run into a few probl=
ems.
Cross-compiler i use to compile applications was built using Crosstools=
and
based on gcc 3.3.4. I use Xilinx EDK 7.1 for integrating hardware perip=
herals
onto the board.
The problems i've seen are:
(i) gettimeofday software function returns time of 0 all the time.
(ii) The Linux 2.6.24 kernel's Xilinx Framebuffer driver and/or the Xil=
inx
PLB TFT Controller IP block (plb_tft_cntlr_ref_v1_00_d) does not a=
ppear
to centre the display on a VGA screen properly(vertically offset).=
(iii) 64-bit write/read access to peripheral integrated onto the Xilinx=
Virtex-II Pro FPGA either causes a system crash or only lower par=
t
of 32-bit data to be written (i.e. lower part of 64-bit data appe=
ars
to be mirrored on the upper and lower 32-bits of the system bus).=
However, 32-bit write/read access to the peripheral passes as wel=
l
as 64-bit write/read access to the SDRAM memory address space. Peripheral interface has been verified to be IBM PLB compliant via IBM bus functional model simulations.
(iv) The Linux 2.6.26 Xilinx Framebuffer driver on the Xilinx XUPV2P b=
oard
does not appear to be working - nothing displayed to screen/conso=
le
not switching to framebuffer device on bootup.
Just wondering if anybody has seen these issues before and know how to=
resolve them?
Any info. appreciated,
Regards,
Alan.
I meet the problem as yours . And my vga's display is not clear , have you meet this?
Quoted 61 lines · Alan Casey
Hi,
I have tried running the Linux 2.6.24 and Linux 2.6.26 kernels from git.xilinx.com on the Xilinx XUPV2P board but have run into a few
problems.Cross-compiler i use to compile applications was built using Crosstools
and
based on gcc 3.3.4. I use Xilinx EDK 7.1 for integrating hardware
peripherals
onto the board.The problems i've seen are:
(i) gettimeofday software function returns time of 0 all the time.
(ii) The Linux 2.6.24 kernel's Xilinx Framebuffer driver and/or the
XilinxPLB TFT Controller IP block (
plb_tft_cntlr_ref_v1_00_d) does not
appearto centre the display on a VGA screen properly(vertically offset).
(iii) 64-bit write/read access to peripheral integrated onto the Xilinx
Virtex-II Pro FPGA either causes a system crash or only lower part
of 32-bit data to be written (i.e. lower part of 64-bit data
appears
to be mirrored on the upper and lower 32-bits of the system bus). However, 32-bit write/read access to the peripheral passes as well as 64-bit write/read access to the SDRAM memory address space. Peripheral interface has been verified to be IBM PLB compliant via IBM bus functional model simulations.(iv) The Linux 2.6.26 Xilinx Framebuffer driver on the Xilinx XUPV2P
boarddoes not appear to be working - nothing displayed to
screen/consolenot switching to framebuffer device on bootup.
Just wondering if anybody has seen these issues before and know how to resolve them?
Any info. appreciated,
Regards,
Alan._______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Signature · 2 lines
View this message in context: http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp18262250p18995644.html Sent from the linuxppc-embedded mailing list archive at Nabble.com.
Hi,
Yes i had a problem with using one of the Linux 2.6.26 kernel versions on the XUPV2P board where the VGA display has not driven correctly, not sure why. The Linux 2.6.24 kernel from git.xilinx.com works fine.
Regards,
Alan.
Quoted 9 lines
-- Original Message --
Date: Fri, 15 Aug 2008 01:43:37 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardI meet the problem as yours . And my vga's display is not clear , have
you
Quoted 13 lines
meet this?
Quoted 10 lines · Alan Casey
Hi,
I have tried running the Linux 2.6.24 and Linux 2.6.26 kernels from
git.xilinx.com on the Xilinx XUPV2P board but have run into a few
problems.Cross-compiler i use to compile applications was built using Crossto=
ols
Quoted 5 lines
Quoted 5 lines
and
based on gcc 3.3.4. I use Xilinx EDK 7.1 for integrating hardware
peripherals
onto the board.
Quoted 8 lines
Quoted 8 lines
The problems i've seen are:
(i) gettimeofday software function returns time of 0 all the time.
(ii) The Linux 2.6.24 kernel's Xilinx Framebuffer driver and/or the
XilinxPLB TFT Controller IP block (
plb_tft_cntlr_ref_v1_00_d) does no=
t
Quoted 3 lines
Quoted 3 lines
appear
to centre the display on a VGA screen properly(vertically offse=
t).
Quoted 2 lines
Quoted 2 lines
(iii) 64-bit write/read access to peripheral integrated onto the Xil=
inx
Quoted 2 lines
Quoted 2 lines
Virtex-II Pro FPGA either causes a system crash or only lower
part
Quoted 4 lines
Quoted 4 lines
of 32-bit data to be written (i.e. lower part of 64-bit data
appears
to be mirrored on the upper and lower 32-bits of the system bu=
s).
Quoted 1 line
Quoted 1 line
However, 32-bit write/read access to the peripheral passes as
well
Quoted 8 lines
Quoted 8 lines
as 64-bit write/read access to the SDRAM memory address space.=
Peripheral interface has been verified to be IBM PLB compliant=
via IBM bus functional model simulations.
(iv) The Linux 2.6.26 Xilinx Framebuffer driver on the Xilinx XUPV2=
P
Quoted 19 lines
Quoted 8 lines
board
does not appear to be working - nothing displayed to
screen/consolenot switching to framebuffer device on bootup.
Just wondering if anybody has seen these issues before and know how=
to
Quoted 9 lines
resolve them?
Any info. appreciated,
Regards,
Alan.
Quoted 9 lines
Quoted 6 lines
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embeddedSignature · 1 line
View this message in context: http://www.nabble.com/Linux-issues-on-Xili=
nx-XUPV2P-board-tp18262250p18995644.html
Quoted 6 lines
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Hi Alan
I dow load the kernel from "
http://git.xilinx.com/cgi-bin/gitweb.cgi?p=linux-2.6-xlnx.git;a=summary "
Merge ../../linux-2.6 into 2.6.26-merge master commit | commitdiff | tree | snapshot
this version ,but it not work well,which version you downloaded?
Many thanks
yanlong
Quoted 58 lines · Alan Casey
Hi,
Yes i had a problem with using one of the Linux 2.6.26 kernel versions on the XUPV2P board where the VGA display has not driven correctly, not sure why. The Linux 2.6.24 kernel from git.xilinx.com works fine.
Regards,
Alan.Quoted 9 lines
-- Original Message --
Date: Fri, 15 Aug 2008 01:43:37 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardI meet the problem as yours . And my vga's display is not clear , have
you
Quoted 36 lines
meet this?
Quoted 33 lines · Alan Casey
Hi,
I have tried running the Linux 2.6.24 and Linux 2.6.26 kernels from
git.xilinx.com on the Xilinx XUPV2P board but have run into a few
problems.Cross-compiler i use to compile applications was built using
Crosstools
and
based on gcc 3.3.4. I use Xilinx EDK 7.1 for integrating hardware
peripherals
onto the board.The problems i've seen are:
(i) gettimeofday software function returns time of 0 all the time.
(ii) The Linux 2.6.24 kernel's Xilinx Framebuffer driver and/or the
XilinxPLB TFT Controller IP block (
plb_tft_cntlr_ref_v1_00_d) does not
appearto centre the display on a VGA screen properly(vertically
offset).(iii) 64-bit write/read access to peripheral integrated onto the
XilinxVirtex-II Pro FPGA either causes a system crash or only lower
Quoted 41 lines
part
Quoted 6 lines
Quoted 6 lines
of 32-bit data to be written (i.e. lower part of 64-bit data
appears
to be mirrored on the upper and lower 32-bits of the system
bus).
However, 32-bit write/read access to the peripheral passes aswell
Quoted 33 lines
Quoted 8 lines
as 64-bit write/read access to the SDRAM memory address space. Peripheral interface has been verified to be IBM PLB compliant
via IBM bus functional model simulations.
(iv) The Linux 2.6.26 Xilinx Framebuffer driver on the Xilinx XUPV2P
boardQuoted 6 lines
does not appear to be working - nothing displayed to
screen/consolenot switching to framebuffer device on bootup.
Just wondering if anybody has seen these issues before and know how
to
Quoted 15 lines
resolve them?
Any info. appreciated,
Regards,
Alan._______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embeddedSignature · 1 line
View this message in context:
http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp18262250p18995644.html
Quoted 14 lines
Quoted 6 lines
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Signature · 2 lines
View this message in context: http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp18262250p18997255.html Sent from the linuxppc-embedded mailing list archive at Nabble.com.
Hi,
I used version 2.6.24. Current version is 2.6.26+ but im not sure how to download previous versions from the git tree, there should be some info at http://git.xilinx.com
about how to do this.
Regards,
Alan.
Quoted 11 lines
-- Original Message --
Date: Fri, 15 Aug 2008 04:35:01 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardHi Alan
I dow load the kernel from "
http://git.xilinx.com/cgi-bin/gitweb.cgi?p=3Dlinux-2.6-xlnx.git;a=3Dsumm=
ary
"
Quoted 2 lines
Merge ../../linux-2.6 into 2.6.26-merge master commit | commitdiff | t=
ree
Quoted 30 lines
| snapshot
this version ,but it not work well,which version you downloaded?
Many thanks
yanlongQuoted 21 lines · Alan Casey
Hi,
Yes i had a problem with using one of the Linux 2.6.26 kernel versions on the XUPV2P board where the VGA display has not driven correctly, not sure why. The Linux 2.6.24 kernel from git.xilinx.com works fine.
Regards,
Alan.Quoted 9 lines
-- Original Message --
Date: Fri, 15 Aug 2008 01:43:37 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardI meet the problem as yours . And my vga's display is not clear , hav=
e
Quoted 8 lines
Quoted 8 lines
you
Quoted 7 lines
meet this?
Quoted 4 lines · Alan Casey
Hi,
I have tried running the Linux 2.6.24 and Linux 2.6.26 kernels fro=
m
Quoted 12 lines
Quoted 12 lines
Quoted 12 lines
Quoted 12 lines
git.xilinx.com on the Xilinx XUPV2P board but have run into a few
problems.Cross-compiler i use to compile applications was built using
Crosstools
and
based on gcc 3.3.4. I use Xilinx EDK 7.1 for integrating hardware
peripherals
onto the board.
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
The problems i've seen are:
(i) gettimeofday software function returns time of 0 all the time.=
(ii) The Linux 2.6.24 kernel's Xilinx Framebuffer driver and/or th=
e
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Xilinx
PLB TFT Controller IP block (
plb_tft_cntlr_ref_v1_00_d) does
not
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
appear
to centre the display on a VGA screen properly(vertically
offset).(iii) 64-bit write/read access to peripheral integrated onto the
XilinxVirtex-II Pro FPGA either causes a system crash or only lowe=
r
Quoted 8 lines
Quoted 8 lines
part
Quoted 7 lines
Quoted 7 lines
of 32-bit data to be written (i.e. lower part of 64-bit data=
appears
to be mirrored on the upper and lower 32-bits of the system
bus).
However, 32-bit write/read access to the peripheral passes a=
s
Quoted 2 lines
Quoted 2 lines
well
Quoted 1 line
Quoted 1 line
as 64-bit write/read access to the SDRAM memory address spac=
e.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Peripheral interface has been verified to be IBM PLB complia=
nt
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
via IBM bus functional model simulations.
(iv) The Linux 2.6.26 Xilinx Framebuffer driver on the Xilinx XUP=
V2P
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
board
does not appear to be working - nothing displayed to
screen/consolenot switching to framebuffer device on bootup.
Just wondering if anybody has seen these issues before and know h=
ow
Quoted 17 lines
Quoted 17 lines
Quoted 17 lines
to
Quoted 15 lines
resolve them?
Any info. appreciated,
Regards,
Alan._______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Quoted 3 lines
Quoted 2 lines
Quoted 2 lines
Signature · 1 line
View this message in context:http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp18262250p189=
95644.html
Quoted 8 lines
Quoted 8 lines
Quoted 6 lines
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Quoted 9 lines
Quoted 6 lines
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embeddedSignature · 1 line
View this message in context: http://www.nabble.com/Linux-issues-on-Xili=
nx-XUPV2P-board-tp18262250p18997255.html
Quoted 6 lines
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Hi Alan,
I'm assuming you must not have Git installed from the question, otherwise you would be using git clone as the site shows.
On the http://git.xilinx.com, it says the following, =
Users without Git installed may create a tar file by using the snapshot feature. Select the tree view of the repository (far right side) on this page, then select snapshot (near the top) and a gziped tar file will be created and downloaded. =
Is this what you're looking for?
-- John
Quoted 254 lines
-----Original Message-----
From: =[mailto:linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs. org] On Behalf Of Alan Casey
Sent: Friday, August 15, 2008 6:34 AM
To: wangyanlong; [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P board
=Hi,
=I used version 2.6.24. Current version is 2.6.26+ but im not sure how to download previous versions from the git tree, there should be some info at http://git.xilinx.com
about how to do this.
=Regards,
Alan.
=Quoted 8 lines
-- Original Message --
Date: Fri, 15 Aug 2008 04:35:01 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardQuoted 4 lines
Hi Alan =
I dow load the kernel from "
http://git.xilinx.com/cgi-bin/gitweb.cgi?p=3Dlinux-2.6-xlnx.git;a=3Dsummary
"Quoted 2 lines
Merge ../../linux-2.6 into 2.6.26-merge master commit | =
commitdiff | tree
Quoted 37 lines
| snapshot
=this version ,but it not work well,which version you downloaded?
Many thanks
yanlong
=Quoted 26 lines · Alan Casey
=
Hi,
=Yes i had a problem with using one of the Linux 2.6.26 kernel versions on the XUPV2P board where the VGA display has not driven correctly, not sure why. The Linux 2.6.24 kernel from git.xilinx.com works fine.
=Regards,
Alan.
==
Quoted 9 lines
-- Original Message --
Date: Fri, 15 Aug 2008 01:43:37 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardI meet the problem as yours . And my vga's display is not =
clear , have
Quoted 10 lines
Quoted 10 lines
you
Quoted 9 lines
meet this?
Quoted 6 lines · Alan Casey
=
Hi,
=I have tried running the Linux 2.6.24 and Linux 2.6.26 =
kernels from
Quoted 5 lines
Quoted 5 lines
=
Quoted 3 lines
=
Quoted 1 line
git.xilinx.com on the Xilinx XUPV2P board but have run =
into a few
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
problems.
=Cross-compiler i use to compile applications was built using
Crosstools
and
based on gcc 3.3.4. I use Xilinx EDK 7.1 for =integrating hardware
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
peripherals
onto the board.
=The problems i've seen are:
=(i) gettimeofday software function returns time of 0 =
all the time.
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
=
(ii) The Linux 2.6.24 kernel's Xilinx Framebuffer =
driver and/or the
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Xilinx
PLB TFT Controller IP block =
(
plb_tft_cntlr_ref_v1_00_d) does
notQuoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
appear
=to centre the display on a VGA screen properly(vertically
offset).
=(iii) 64-bit write/read access to peripheral =
integrated onto the
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Xilinx
=Virtex-II Pro FPGA either causes a system crash =
or only lower
Quoted 4 lines
Quoted 4 lines
part
Quoted 3 lines
Quoted 3 lines
=
of 32-bit data to be written (i.e. lower part of =
64-bit data
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
appears
to be mirrored on the upper and lower 32-bits of =the system
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
bus).
However, 32-bit write/read access to the =peripheral passes as
Quoted 2 lines
Quoted 2 lines
well
Quoted 1 line
Quoted 1 line
as 64-bit write/read access to the SDRAM memory =
address space.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Peripheral interface has been verified to be IBM =
PLB compliant
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
via IBM bus functional model simulations. =
=
(iv) The Linux 2.6.26 Xilinx Framebuffer driver on =
the Xilinx XUPV2P
Quoted 7 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
board
=does not appear to be working - nothing displayed to
screen/console
=Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
not switching to framebuffer device on bootup. =
=
Just wondering if anybody has seen these issues =
before and know how
Quoted 21 lines
Quoted 20 lines
Quoted 20 lines
to
Quoted 19 lines
resolve them?
=Any info. appreciated,
Regards,
Alan.
==
=
=
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
=Quoted 7 lines
Quoted 6 lines
Quoted 6 lines
Quoted 1 line
=
-- =
View this message in context:
http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp1
8262250p18995644.html
Quoted 16 lines
Quoted 15 lines
Quoted 6 lines
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded=
=
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
=Quoted 6 lines
Quoted 1 line
=
-- =
View this message in context: =
http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp18
262250p18997255.htmlQuoted 6 lines
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded=
=
Quoted 7 lines
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
==
This email and any attachments are intended for the sole use of the named r= ecipient(s) and contain(s) confidential information that may be proprietary= , privileged or copyrighted under applicable law. If you are not the intend= ed recipient, do not read, copy, or forward this email message or any attac= hments. Delete this email message and any attachments immediately.
Hi
v2.6.24 v2.6.24-rc8 v2.6.24-rc7 v2.6.24-rc6 v2.6.24-rc5 v2.6.24-rc4 v2.6.24-rc3 v2.6.24-rc2
many versions, which one ???
Thanks :)
v2.6.24-rc1
Hi,
I used version 2.6.24. Current version is 2.6.26+ but im not sure how to download previous versions from the git tree, there should be some info at http://git.xilinx.com
about how to do this.
Regards,
Alan.
Signature · 2 lines
View this message in context: http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp18262250p18999662.html Sent from the linuxppc-embedded mailing list archive at Nabble.com.
Hi John,
Im not having any problems using GIT. I can download 2.6.26 using git no problem - i think wangyanlong would like to use 2.6.24 or 2.6.26 and he has problems downloading it using git - hence i replied to him that he may find more info about how to download the current or previous version on git.xilinx.com. I think you misread my email.
The Xilinx Framebuffer driver works fine in Linux 2.6.24 but there appears to be a problem with one of the Linux-2.6.26 versions which i posted about a few weeks/months ago.
Alan.
Quoted 216 lines
-- Original Message --
Subject: RE: Linux issues on Xilinx XUPV2P board
Date: Fri, 15 Aug 2008 08:30:25 -0600
From: John Linn <[email protected]>
To: <[email protected]>,
"wangyanlong" <[email protected]>,
<[email protected]>Hi Alan,
I'm assuming you must not have Git installed from the question, otherwise you would be using git clone as the site shows.
On the http://git.xilinx.com, it says the following,
Users without Git installed may create a tar file by using the snapshot feature. Select the tree view of the repository (far right side) on this=
page, then select snapshot (near the top) and a gziped tar file will be created and downloaded.
Is this what you're looking for?
-- John
Quoted 190 lines
-----Original Message-----
From:
[email protected] [mailto:linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs. org] On Behalf Of Alan Casey
Sent: Friday, August 15, 2008 6:34 AM
To: wangyanlong; [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardHi,
I used version 2.6.24. Current version is 2.6.26+ but im not sure how to download previous versions from the git tree, there should be some info at http://git.xilinx.com
about how to do this.Regards,
Alan.Quoted 11 lines
-- Original Message --
Date: Fri, 15 Aug 2008 04:35:01 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardHi Alan
I dow load the kernel from "
http://git.xilinx.com/cgi-bin/gitweb.cgi?p=3Dlinux-2.6-xlnx.git;a=3Dsummary
"Quoted 2 lines
Merge ../../linux-2.6 into 2.6.26-merge master commit |
commitdiff | tree
Quoted 30 lines
| snapshot
this version ,but it not work well,which version you downloaded?
Many thanks
yanlongQuoted 21 lines · Alan Casey
Hi,
Yes i had a problem with using one of the Linux 2.6.26 kernel versions on the XUPV2P board where the VGA display has not driven correctly, not sure why. The Linux 2.6.24 kernel from git.xilinx.com works fine.
Regards,
Alan.Quoted 9 lines
-- Original Message --
Date: Fri, 15 Aug 2008 01:43:37 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardI meet the problem as yours . And my vga's display is not
clear , have
Quoted 8 lines
Quoted 8 lines
you
Quoted 7 lines
meet this?
Quoted 4 lines · Alan Casey
Hi,
I have tried running the Linux 2.6.24 and Linux 2.6.26
kernels from
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
git.xilinx.com on the Xilinx XUPV2P board but have run
into a few
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
problems.
Cross-compiler i use to compile applications was built using
Crosstools
and
based on gcc 3.3.4. I use Xilinx EDK 7.1 forintegrating hardware
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
peripherals
onto the board.The problems i've seen are:
(i) gettimeofday software function returns time of 0
all the time.
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
(ii) The Linux 2.6.24 kernel's Xilinx Framebuffer
driver and/or the
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Xilinx
PLB TFT Controller IP block
(
plb_tft_cntlr_ref_v1_00_d) does
notQuoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
appear
to centre the display on a VGA screen properly(vertically
offset).(iii) 64-bit write/read access to peripheral
integrated onto the
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Xilinx
Virtex-II Pro FPGA either causes a system crash
or only lower
Quoted 3 lines
Quoted 3 lines
part
Quoted 2 lines
Quoted 2 lines
of 32-bit data to be written (i.e. lower part of
64-bit data
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
appears
to be mirrored on the upper and lower 32-bits ofthe system
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
bus).
However, 32-bit write/read access to theperipheral passes as
Quoted 2 lines
Quoted 2 lines
well
Quoted 1 line
Quoted 1 line
as 64-bit write/read access to the SDRAM memory
address space.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Peripheral interface has been verified to be IBM
PLB compliant
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
via IBM bus functional model simulations.
(iv) The Linux 2.6.26 Xilinx Framebuffer driver on
the Xilinx XUPV2P
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
board
does not appear to be working - nothing displayed to
screen/consolenot switching to framebuffer device on bootup.
Just wondering if anybody has seen these issues
before and know how
Quoted 17 lines
Quoted 17 lines
Quoted 17 lines
to
Quoted 15 lines
resolve them?
Any info. appreciated,
Regards,
Alan._______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embeddedQuoted 3 lines
Quoted 2 lines
Quoted 2 lines
Signature · 1 line
View this message in context:http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp1
8262250p18995644.html
Quoted 9 lines
Quoted 9 lines
Quoted 7 lines
Sent from the linuxppc-embedded mailing list archive at Nabble.com.=
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embeddedQuoted 9 lines
Quoted 6 lines
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embeddedSignature · 1 line
View this message in context:http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp18
262250p18997255.htmlQuoted 6 lines
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Quoted 8 lines
Quoted 6 lines
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embeddedThis email and any attachments are intended for the sole use of the name=
d
Quoted 1 line
recipient(s) and contain(s) confidential information that may be proprie=
tary,
Quoted 1 line
privileged or copyrighted under applicable law. If you are not the inten=
ded
Quoted 1 line
recipient, do not read, copy, or forward this email message or any attac=
hments.
Quoted 3 lines
Delete this email message and any attachments immediately.
Hi,
2.6.24-rc8 was the version i think i used.
2.6.24 should be fine also.
Alan.
Quoted 27 lines
-- Original Message --
Date: Fri, 15 Aug 2008 07:31:35 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardHi
v2.6.24 v2.6.24-rc8 v2.6.24-rc7 v2.6.24-rc6 v2.6.24-rc5 v2.6.24-rc4 v2.6.24-rc3 v2.6.24-rc2many versions, which one ???
Thanks :)v2.6.24-rc1Hi,
Quoted 11 lines
I used version 2.6.24. Current version is 2.6.26+ but im not sure how to download previous versions from the git tree, there should be some info at http://git.xilinx.com
about how to do this.Regards,
Alan.Signature · 1 line
View this message in context: http://www.nabble.com/Linux-issues-on-Xili=
nx-XUPV2P-board-tp18262250p18999662.html
Quoted 6 lines
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Ah I see, sorry about that, misunderstood what was needed.
So there may be other ways as I'm not a Git expert, but I clone the repository, then reset to the a Git tag.
Quoted 1 line
git reset --hard <tag name>
We're working on a new frame buffer driver for a new core, but the old frame buffer has not been high priority for us.
Thanks,
John =
Quoted 344 lines
-----Original Message-----
From: Alan Casey [mailto:[email protected]] =Sent: Friday, August 15, 2008 8:36 AM
To: John Linn; wangyanlong; [email protected]
Subject: RE: Linux issues on Xilinx XUPV2P board =Hi John,
=Im not having any problems using GIT. I can download 2.6.26 using git no problem - i think wangyanlong would like to use 2.6.24 or 2.6.26 and he has problems downloading it using git - hence i replied to him that he may find more info about how to download the current or previous version on git.xilinx.com. I think you misread my email.
=The Xilinx Framebuffer driver works fine in Linux 2.6.24 but there appears to be a problem with one of the Linux-2.6.26 versions which i posted about a few weeks/months ago.
=Alan.
=Quoted 11 lines
-- Original Message --
Subject: RE: Linux issues on Xilinx XUPV2P board
Date: Fri, 15 Aug 2008 08:30:25 -0600
From: John Linn <[email protected]>
To: <[email protected]>,
"wangyanlong" <[email protected]>,
<[email protected]>Hi Alan,
Quoted 7 lines
I'm assuming you must not have Git installed from the question, otherwise you would be using git clone as the site shows.
On the http://git.xilinx.com, it says the following, =
Users without Git installed may create a tar file by using =
the snapshot
Quoted 1 line
feature. Select the tree view of the repository (far right =
side) on this
Quoted 1 line
page, then select snapshot (near the top) and a gziped tar =
file will be
Quoted 142 lines
created and downloaded. =
Is this what you're looking for?
-- John
Quoted 135 lines
-----Original Message-----
From: =[mailto:linuxppc-embedded-bounces+john.linn=3Dxilinx.com@ozlabs. org] On Behalf Of Alan Casey
Sent: Friday, August 15, 2008 6:34 AM
To: wangyanlong; [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P board
=Hi,
=I used version 2.6.24. Current version is 2.6.26+ but im not sure how to download previous versions from the git tree, there should be some info at http://git.xilinx.com
about how to do this.
=Regards,
Alan.
=Quoted 8 lines
-- Original Message --
Date: Fri, 15 Aug 2008 04:35:01 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardQuoted 4 lines
Hi Alan =
I dow load the kernel from "
http://git.xilinx.com/cgi-bin/gitweb.cgi?p=3Dlinux-2.6-xlnx.git;a=3Dsummary
"Quoted 2 lines
Merge ../../linux-2.6 into 2.6.26-merge master commit | =
commitdiff | tree
Quoted 37 lines
| snapshot
=this version ,but it not work well,which version you downloaded?
Many thanks
yanlong
=Quoted 26 lines · Alan Casey
=
Hi,
=Yes i had a problem with using one of the Linux 2.6.26 kernel versions on the XUPV2P board where the VGA display has not driven correctly, not sure why. The Linux 2.6.24 kernel from git.xilinx.com works fine.
=Regards,
Alan.
==
Quoted 9 lines
-- Original Message --
Date: Fri, 15 Aug 2008 01:43:37 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardI meet the problem as yours . And my vga's display is not =
clear , have
Quoted 10 lines
Quoted 10 lines
you
Quoted 9 lines
meet this?
Quoted 6 lines · Alan Casey
=
Hi,
=I have tried running the Linux 2.6.24 and Linux 2.6.26 =
kernels from
Quoted 5 lines
Quoted 5 lines
=
Quoted 3 lines
=
Quoted 1 line
git.xilinx.com on the Xilinx XUPV2P board but have run =
into a few
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
problems.
=Cross-compiler i use to compile applications was built using
Crosstools
and
based on gcc 3.3.4. I use Xilinx EDK 7.1 for =integrating hardware
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
peripherals
onto the board.
=The problems i've seen are:
=(i) gettimeofday software function returns time of 0 =
all the time.
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
=
(ii) The Linux 2.6.24 kernel's Xilinx Framebuffer =
driver and/or the
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Xilinx
PLB TFT Controller IP block =
(
plb_tft_cntlr_ref_v1_00_d) does
notQuoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
appear
=to centre the display on a VGA screen =
properly(vertically
Quoted 78 lines
Quoted 78 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
offset).
=(iii) 64-bit write/read access to peripheral =
integrated onto the
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Xilinx
=Virtex-II Pro FPGA either causes a system crash =
or only lower
Quoted 4 lines
Quoted 4 lines
part
Quoted 3 lines
Quoted 3 lines
=
of 32-bit data to be written (i.e. lower part of =
64-bit data
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
appears
to be mirrored on the upper and lower 32-bits of =the system
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
bus).
However, 32-bit write/read access to the =peripheral passes as
Quoted 2 lines
Quoted 2 lines
well
Quoted 1 line
Quoted 1 line
as 64-bit write/read access to the SDRAM memory =
address space.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Peripheral interface has been verified to be IBM =
PLB compliant
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
via IBM bus functional model simulations. =
=
(iv) The Linux 2.6.26 Xilinx Framebuffer driver on =
the Xilinx XUPV2P
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
board
=does not appear to be working - nothing displayed to
screen/consolenot switching to framebuffer device on bootup. =
=
Just wondering if anybody has seen these issues =
before and know how
Quoted 24 lines
Quoted 24 lines
Quoted 24 lines
to
Quoted 21 lines
resolve them?
=Any info. appreciated,
Regards,
Alan.
==
=
=
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
==
Quoted 6 lines
Quoted 6 lines
Quoted 4 lines
Quoted 3 lines
Quoted 3 lines
-- =
View this message in context:
http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp1
8262250p18995644.html
Quoted 1 line
Quoted 1 line
Quoted 1 line
Sent from the linuxppc-embedded mailing list archive at =
Nabble.com.
Quoted 18 lines
Quoted 18 lines
Quoted 18 lines
Quoted 16 lines
Quoted 5 lines
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded=
=
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
==
Quoted 7 lines
Quoted 7 lines
Quoted 3 lines
-- =
View this message in context: =
http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp18
262250p18997255.htmlQuoted 1 line
Sent from the linuxppc-embedded mailing list archive at =
Nabble.com.
Quoted 15 lines
Quoted 14 lines
Quoted 5 lines
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded=
=
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
=Quoted 4 lines
Quoted 1 line
=
This email and any attachments are intended for the sole use =
of the named
Quoted 1 line
recipient(s) and contain(s) confidential information that =
may be proprietary,
Quoted 1 line
privileged or copyrighted under applicable law. If you are =
not the intended
Quoted 1 line
recipient, do not read, copy, or forward this email message =
or any attachments.
Quoted 3 lines
Delete this email message and any attachments immediately.
Quoted 7 lines
=
=
=
=
This email and any attachments are intended for the sole use of the named r= ecipient(s) and contain(s) confidential information that may be proprietary= , privileged or copyrighted under applicable law. If you are not the intend= ed recipient, do not read, copy, or forward this email message or any attac= hments. Delete this email message and any attachments immediately.
Quoted 5 lines · John Linn
Ah I see, sorry about that, misunderstood what was needed.
So there may be other ways as I'm not a Git expert, but I clone the repository, then reset to the a Git tag.
Quoted 7 lines
Quoted 1 line
git reset --hard <tag name>
We're working on a new frame buffer driver for a new core, but the old frame buffer has not been high priority for us.
Thanks,
John
While this "Works" in the sense that it makes your working directory look like the contents of the given tag, you are now using a "detached HEAD" -- ie, no real branch.
If you think you will ever want to make a change or check in something, you might be better to create a branch based on the original tag, perhaps something like:
$ git checkout -b my-v2.6.24 v2.6.24
HTH,
jdl
Hi
For 4 days ,i corrected the ip 's bug . Thanks for your help . The
solution is here http://www.openhard.org/myspace/blog/show_155462.html
Regards
yanlong
Quoted 46 lines · Alan Casey
Hi,
2.6.24-rc8 was the version i think i used.
2.6.24 should be fine also.Alan.
Quoted 38 lines
-- Original Message --
Date: Fri, 15 Aug 2008 07:31:35 -0700 (PDT)
From: wangyanlong <[email protected]>
To: [email protected]
Subject: Re: Linux issues on Xilinx XUPV2P boardHi
v2.6.24 v2.6.24-rc8 v2.6.24-rc7 v2.6.24-rc6 v2.6.24-rc5 v2.6.24-rc4 v2.6.24-rc3 v2.6.24-rc2many versions, which one ???
Thanks :)v2.6.24-rc1Hi,
I used version 2.6.24. Current version is 2.6.26+ but im not sure how to download previous versions from the git tree, there should be some info at http://git.xilinx.com
about how to do this.Regards,
Alan.Signature · 1 line
View this message in context:
http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp18262250p18999662.html
Quoted 14 lines
Quoted 6 lines
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Signature · 2 lines
View this message in context: http://www.nabble.com/Linux-issues-on-Xilinx-XUPV2P-board-tp18262250p19243481.html Sent from the linuxppc-embedded mailing list archive at Nabble.com.