Skip to contentSkip to conversation

No sound with intel hda driver on a sony vaio vgx xl100 system

DISCUSSION [email protected] 3 participants 7 messages Jan 22, 2007 – Jan 26, 2007

lore
Share & tools
lore
#0 lore raw

Hi

I can't have any sound on my sony VAIO vgx-xl100 system with the 1.0.14rc2 build on a 2.6.18 kernel (debian)

the output of lspci -nv is :

00:1b.0 0403: 8086:27d8 (rev 01)

	Subsystem: 104d:81f7
	Flags: bus master, fast devsel, latency 0, IRQ 169
	Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>

dmesg gives :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696:
codec_mask = 0x1
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:611:
AUD_IN = 6
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:
UNMUTE IN: NID=0x6 IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:
UNMUTE IN: NID=0xe IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:
UNMUTE IN: NID=0x7 IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:
UNMUTE OUT: NID=0x7
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:648:
[Capture Source] NID=0x6, #SRC=1
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:651:
[Line] IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:289:
AUD_OUT found 2
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:
UNMUTE IN: NID=0xa IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:
UNMUTE OUT: NID=0xa
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:
UNMUTE OUT: NID=0xa
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:251:
CONNECT: NID=0x6 IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:713:
[Master Playback Switch] NID=0x2, DIR=OUT
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:733:
[Master Playback Volume] NID=0x2, DIR=OUT

and the contents of /proc/asound/card0/codec# is :

Codec: SigmaTel CXD9872RD/K
Address: 0
Vendor Id: 0x83847661
Subsystem Id: 0x104d0b00
Revision Id: 0x104201
Default PCM:

    rates [0x7e0]: 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Default Amp-In caps: ofs=0x00, nsteps=0x0f, stepsize=0x05, mute=1 Default Amp-Out caps: ofs=0x7f, nsteps=0x7f, stepsize=0x02, mute=1 Node 0x02 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0x3c 0x3c]
Power: 0x0
Node 0x03 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0xff 0xff]
Power: 0x0
Node 0x04 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0xff 0xff]
Power: 0x0
Node 0x05 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0x3c 0x3c]
Power: 0x0
Node 0x06 [Audio Input] wcaps 0x1d0541: Stereo
Power: 0x0
Connection: 1

     0x07

Node 0x07 [Audio Selector] wcaps 0x300903: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x00 0x00]
Connection: 1

     0x0e
Node 0x08 [Audio Input] wcaps 0x1d0541: Stereo
  Power: 0x0
  Connection: 1
     0x09

Node 0x09 [Audio Selector] wcaps 0x300903: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x80 0x80]
Connection: 1

     0x15

Node 0x0a [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x08173c: IN OUT HP Detect
Pin Default 0x02024110: [Jack] Line Out at Ext Front
Conn = 1/4, Color = Green
Pin-ctls: 0xc0: OUT HP
Connection: 1

     0x02

Node 0x0b [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x00:
Connection: 1

     0x04

Node 0x0c [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x00:
Connection: 1

     0x03

Node 0x0d [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x08173c: IN OUT HP Detect
Pin Default 0x02a19920: [Jack] Mic at Ext Front
Conn = 1/8, Color = Pink
Pin-ctls: 0x24: IN
Connection: 1

     0x02

Node 0x0e [Pin Complex] wcaps 0x400081: Stereo
Pincap 0x0824: IN Detect
Pin Default 0x01845121: [Jack] Line In at Ext Rear
Conn = RCA, Color = Red
Pin-ctls: 0x20: IN
Node 0x0f [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x01045111: [Jack] Line Out at Ext Rear
Conn = RCA, Color = Red
Pin-ctls: 0x40: OUT
Connection: 1

     0x05
Node 0x10 [Audio Output] wcaps 0x40211: Stereo Digital
  PCM:
    rates [0x3e0]: 44100 48000 88200 96000 176400
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Node 0x11 [Pin Complex] wcaps 0x400301: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x01451112: [Jack] SPDIF Out at Ext Rear
Conn = Optical, Color = Black
Pin-ctls: 0x00:
Connection: 2

     0x10* 0x09
Node 0x12 [Audio Input] wcaps 0x140311: Stereo Digital
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Connection: 1
     0x13

Node 0x13 [Pin Complex] wcaps 0x440381: Stereo Digital
Pincap 0x0834: IN OUT Detect
Pin Default 0x01c51122: [Jack] SPDIF In at Ext Rear
Conn = Optical, Color = Black
Pin-ctls: 0x00:
Connection: 1

     0x18

Node 0x14 [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x0820: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Node 0x15 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=1 Amp-Out vals: [0x00 0x00]
Connection: 4

     0x0a 0x0d* 0x14 0x02

Node 0x16 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out
Amp-Out caps: ofs=0x03, nsteps=0x03, stepsize=0x17, mute=0 Amp-Out vals: [0x00]
Node 0x17 [Volume Knob Widget] wcaps 0x600000: Mono Node 0x18 [Audio Output] wcaps 0x40201: Stereo Digital

---------------------------------
Jean-Marc Segretain
mailto:[email protected]

___________________________________________________________________________
Découvrez une nouvelle façon d'obtenir des réponses à toutes vos questions !
Profitez des connaissances, des opinions et des expériences des internautes sur Yahoo! Questions/Réponses
http://fr.answers.yahoo.com

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV

#1 lore raw

Your subsystem ID (104d:81f7) is not listed in the driver currently. The driver is configured to use the generic parser if it can't find a match.

There are two defined models for your codec (vaio, vaio-ar). Try loading the driver with one of those models as follows:
modprobe -r snd-hda-intel # remove driver
modprobe snd-hda-intel model=vaio # reload with model deffinition

Try both model deffinitions to see which works better for you. Report back your results and we'll get it added.

Thanks,

Tobin Davis

Quoted 220 lines · On Mon, 2007-01-22 at 22:22 +0100, [email protected] wrote:

Hi

I can't have any sound on my sony VAIO vgx-xl100 system with the 1.0.14rc2 build on a 2.6.18 kernel (debian)

the output of lspci -nv is :

00:1b.0 0403: 8086:27d8 (rev 01)

	Subsystem: 104d:81f7
	Flags: bus master, fast devsel, latency 0, IRQ 169
	Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>

dmesg gives :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696:
codec_mask = 0x1
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:611:
AUD_IN = 6
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:
UNMUTE IN: NID=0x6 IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:
UNMUTE IN: NID=0xe IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:
UNMUTE IN: NID=0x7 IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:
UNMUTE OUT: NID=0x7
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:648:
[Capture Source] NID=0x6, #SRC=1
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:651:
[Line] IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:289:
AUD_OUT found 2
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:
UNMUTE IN: NID=0xa IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:
UNMUTE OUT: NID=0xa
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:
UNMUTE OUT: NID=0xa
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:251:
CONNECT: NID=0x6 IDX=0x0
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:713:
[Master Playback Switch] NID=0x2, DIR=OUT
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:733:
[Master Playback Volume] NID=0x2, DIR=OUT

and the contents of /proc/asound/card0/codec# is :

Codec: SigmaTel CXD9872RD/K
Address: 0
Vendor Id: 0x83847661
Subsystem Id: 0x104d0b00
Revision Id: 0x104201
Default PCM:

    rates [0x7e0]: 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Default Amp-In caps: ofs=0x00, nsteps=0x0f, stepsize=0x05, mute=1 Default Amp-Out caps: ofs=0x7f, nsteps=0x7f, stepsize=0x02, mute=1 Node 0x02 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0x3c 0x3c]
Power: 0x0
Node 0x03 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0xff 0xff]
Power: 0x0
Node 0x04 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0xff 0xff]
Power: 0x0
Node 0x05 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0x3c 0x3c]
Power: 0x0
Node 0x06 [Audio Input] wcaps 0x1d0541: Stereo
Power: 0x0
Connection: 1

     0x07

Node 0x07 [Audio Selector] wcaps 0x300903: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x00 0x00]
Connection: 1

     0x0e
Node 0x08 [Audio Input] wcaps 0x1d0541: Stereo
  Power: 0x0
  Connection: 1
     0x09

Node 0x09 [Audio Selector] wcaps 0x300903: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x80 0x80]
Connection: 1

     0x15

Node 0x0a [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x08173c: IN OUT HP Detect
Pin Default 0x02024110: [Jack] Line Out at Ext Front
Conn = 1/4, Color = Green
Pin-ctls: 0xc0: OUT HP
Connection: 1

     0x02

Node 0x0b [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x00:
Connection: 1

     0x04

Node 0x0c [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x00:
Connection: 1

     0x03

Node 0x0d [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x08173c: IN OUT HP Detect
Pin Default 0x02a19920: [Jack] Mic at Ext Front
Conn = 1/8, Color = Pink
Pin-ctls: 0x24: IN
Connection: 1

     0x02

Node 0x0e [Pin Complex] wcaps 0x400081: Stereo
Pincap 0x0824: IN Detect
Pin Default 0x01845121: [Jack] Line In at Ext Rear
Conn = RCA, Color = Red
Pin-ctls: 0x20: IN
Node 0x0f [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x01045111: [Jack] Line Out at Ext Rear
Conn = RCA, Color = Red
Pin-ctls: 0x40: OUT
Connection: 1

     0x05
Node 0x10 [Audio Output] wcaps 0x40211: Stereo Digital
  PCM:
    rates [0x3e0]: 44100 48000 88200 96000 176400
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Node 0x11 [Pin Complex] wcaps 0x400301: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x01451112: [Jack] SPDIF Out at Ext Rear
Conn = Optical, Color = Black
Pin-ctls: 0x00:
Connection: 2

     0x10* 0x09
Node 0x12 [Audio Input] wcaps 0x140311: Stereo Digital
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Connection: 1
     0x13

Node 0x13 [Pin Complex] wcaps 0x440381: Stereo Digital
Pincap 0x0834: IN OUT Detect
Pin Default 0x01c51122: [Jack] SPDIF In at Ext Rear
Conn = Optical, Color = Black
Pin-ctls: 0x00:
Connection: 1

     0x18

Node 0x14 [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x0820: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Node 0x15 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=1 Amp-Out vals: [0x00 0x00]
Connection: 4

     0x0a 0x0d* 0x14 0x02

Node 0x16 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out
Amp-Out caps: ofs=0x03, nsteps=0x03, stepsize=0x17, mute=0 Amp-Out vals: [0x00]
Node 0x17 [Volume Knob Widget] wcaps 0x600000: Mono Node 0x18 [Audio Output] wcaps 0x40201: Stereo Digital

---------------------------------
Jean-Marc Segretain
mailto:[email protected]

___________________________________________________________________________
Découvrez une nouvelle façon d'obtenir des réponses à toutes vos questions !
Profitez des connaissances, des opinions et des expériences des internautes sur Yahoo! Questions/Réponses
http://fr.answers.yahoo.com

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel

Signature · 1 line
Tobin Davis <[email protected]>

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV

_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel

#2 lore raw

I have tried both model. none of them works.
Is there anything I missed ?

Quoted 9 lines · --- Tobin Davis

Your subsystem ID (104d:81f7) is not listed in the driver currently. The driver is configured to use the generic parser if it can't find a match.

There are two defined models for your codec (vaio, vaio-ar). Try loading the driver with one of those models as follows:
modprobe -r snd-hda-intel # remove driver
modprobe snd-hda-intel model=vaio # reload with model deffinition

Quoted 31 lines

Try both model deffinitions to see which works better for you. Report back your results and we'll get it added.

Thanks,

Tobin Davis

Quoted 21 lines · On Mon, 2007-01-22 at 22:22 +0100, [email protected] wrote:

Hi

I can't have any sound on my sony VAIO vgx-xl100 system with the 1.0.14rc2 build on a 2.6.18 kernel (debian)

the output of lspci -nv is :

00:1b.0 0403: 8086:27d8 (rev 01)

	Subsystem: 104d:81f7
	Flags: bus master, fast devsel, latency 0, IRQ 169
	Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>

dmesg gives :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64 ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696:

Quoted 4 lines
Quoted 3 lines

codec_mask = 0x1
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:611:

Quoted 4 lines
Quoted 3 lines

AUD_IN = 6
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:

Quoted 4 lines
Quoted 3 lines

UNMUTE IN: NID=0x6 IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:

Quoted 4 lines
Quoted 3 lines

UNMUTE IN: NID=0xe IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:

Quoted 4 lines
Quoted 3 lines

UNMUTE IN: NID=0x7 IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:

Quoted 4 lines
Quoted 3 lines

UNMUTE OUT: NID=0x7
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:648:

Quoted 4 lines
Quoted 3 lines

[Capture Source] NID=0x6, #SRC=1
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:651:

Quoted 4 lines
Quoted 3 lines

[Line] IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:289:

Quoted 4 lines
Quoted 3 lines

AUD_OUT found 2
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:

Quoted 4 lines
Quoted 3 lines

UNMUTE IN: NID=0xa IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:

Quoted 4 lines
Quoted 3 lines

UNMUTE OUT: NID=0xa
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:

Quoted 4 lines
Quoted 3 lines

UNMUTE OUT: NID=0xa
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:251:

Quoted 4 lines
Quoted 3 lines

CONNECT: NID=0x6 IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:713:

Quoted 4 lines
Quoted 3 lines

[Master Playback Switch] NID=0x2, DIR=OUT
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:733:

Quoted 97 lines
Quoted 97 lines

[Master Playback Volume] NID=0x2, DIR=OUT

and the contents of /proc/asound/card0/codec# is :

Codec: SigmaTel CXD9872RD/K
Address: 0
Vendor Id: 0x83847661
Subsystem Id: 0x104d0b00
Revision Id: 0x104201
Default PCM:

    rates [0x7e0]: 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Default Amp-In caps: ofs=0x00, nsteps=0x0f, stepsize=0x05, mute=1 Default Amp-Out caps: ofs=0x7f, nsteps=0x7f, stepsize=0x02, mute=1 Node 0x02 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0x3c 0x3c]
Power: 0x0
Node 0x03 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0xff 0xff]
Power: 0x0
Node 0x04 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0xff 0xff]
Power: 0x0
Node 0x05 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0x3c 0x3c]
Power: 0x0
Node 0x06 [Audio Input] wcaps 0x1d0541: Stereo
Power: 0x0
Connection: 1

     0x07

Node 0x07 [Audio Selector] wcaps 0x300903: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x00 0x00]
Connection: 1

     0x0e
Node 0x08 [Audio Input] wcaps 0x1d0541: Stereo
  Power: 0x0
  Connection: 1
     0x09

Node 0x09 [Audio Selector] wcaps 0x300903: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x80 0x80]
Connection: 1

     0x15

Node 0x0a [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x08173c: IN OUT HP Detect
Pin Default 0x02024110: [Jack] Line Out at Ext Front
Conn = 1/4, Color = Green
Pin-ctls: 0xc0: OUT HP
Connection: 1

     0x02

Node 0x0b [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x00:
Connection: 1

     0x04

Node 0x0c [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x00:
Connection: 1

     0x03

Node 0x0d [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x08173c: IN OUT HP Detect
Pin Default 0x02a19920: [Jack] Mic at Ext Front
Conn = 1/8, Color = Pink
Pin-ctls: 0x24: IN
Connection: 1

     0x02

Node 0x0e [Pin Complex] wcaps 0x400081: Stereo
Pincap 0x0824: IN Detect
Pin Default 0x01845121: [Jack] Line In at Ext Rear
Conn = RCA, Color = Red
Pin-ctls: 0x20: IN
Node 0x0f [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x01045111: [Jack] Line Out at Ext Rear
Conn = RCA, Color = Red
Pin-ctls: 0x40: OUT
Connection: 1

     0x05
Node 0x10 [Audio Output] wcaps 0x40211: Stereo Digital
  PCM:
    rates [0x3e0]: 44100 48000 88200 96000 176400
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Node 0x11 [Pin Complex] wcaps 0x400301: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x01451112: [Jack] SPDIF Out at Ext Rear

Quoted 9 lines
Quoted 8 lines

Conn = Optical, Color = Black
Pin-ctls: 0x00:
Connection: 2

     0x10* 0x09
Node 0x12 [Audio Input] wcaps 0x140311: Stereo Digital
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24

=== message truncated ===

___________________________________________________________________________
Découvrez une nouvelle façon d'obtenir des réponses à toutes vos questions !
Profitez des connaissances, des opinions et des expériences des internautes sur Yahoo! Questions/Réponses
http://fr.answers.yahoo.com

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV

#3 lore raw

At Tue, 23 Jan 2007 23:46:42 +0100 (CET),

Quoted 3 lines · <[email protected]> wrote:

I have tried both model. none of them works.
Is there anything I missed ?

Please elaborate what didn't work exactly. If you specified model option, the kernel messages must appear differently. If not, the model option was not passed properly by any reason.

Takashi

Quoted 233 lines
Quoted 9 lines · --- Tobin Davis

Your subsystem ID (104d:81f7) is not listed in the driver currently. The driver is configured to use the generic parser if it can't find a match.

There are two defined models for your codec (vaio, vaio-ar). Try loading the driver with one of those models as follows:
modprobe -r snd-hda-intel # remove driver
modprobe snd-hda-intel model=vaio # reload with model deffinition

Quoted 31 lines

Try both model deffinitions to see which works better for you. Report back your results and we'll get it added.

Thanks,

Tobin Davis

Quoted 21 lines · On Mon, 2007-01-22 at 22:22 +0100, [email protected] wrote:

Hi

I can't have any sound on my sony VAIO vgx-xl100 system with the 1.0.14rc2 build on a 2.6.18 kernel (debian)

the output of lspci -nv is :

00:1b.0 0403: 8086:27d8 (rev 01)

	Subsystem: 104d:81f7
	Flags: bus master, fast devsel, latency 0, IRQ 169
	Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>

dmesg gives :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64 ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696:

Quoted 4 lines
Quoted 3 lines

codec_mask = 0x1
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:611:

Quoted 4 lines
Quoted 3 lines

AUD_IN = 6
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:

Quoted 4 lines
Quoted 3 lines

UNMUTE IN: NID=0x6 IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:

Quoted 4 lines
Quoted 3 lines

UNMUTE IN: NID=0xe IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:

Quoted 4 lines
Quoted 3 lines

UNMUTE IN: NID=0x7 IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:

Quoted 4 lines
Quoted 3 lines

UNMUTE OUT: NID=0x7
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:648:

Quoted 4 lines
Quoted 3 lines

[Capture Source] NID=0x6, #SRC=1
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:651:

Quoted 4 lines
Quoted 3 lines

[Line] IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:289:

Quoted 4 lines
Quoted 3 lines

AUD_OUT found 2
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:233:

Quoted 4 lines
Quoted 3 lines

UNMUTE IN: NID=0xa IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:

Quoted 4 lines
Quoted 3 lines

UNMUTE OUT: NID=0xa
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:217:

Quoted 4 lines
Quoted 3 lines

UNMUTE OUT: NID=0xa
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:251:

Quoted 4 lines
Quoted 3 lines

CONNECT: NID=0x6 IDX=0x0
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:713:

Quoted 4 lines
Quoted 3 lines

[Master Playback Switch] NID=0x2, DIR=OUT
ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_generic.c:733:

Quoted 97 lines
Quoted 97 lines

[Master Playback Volume] NID=0x2, DIR=OUT

and the contents of /proc/asound/card0/codec# is :

Codec: SigmaTel CXD9872RD/K
Address: 0
Vendor Id: 0x83847661
Subsystem Id: 0x104d0b00
Revision Id: 0x104201
Default PCM:

    rates [0x7e0]: 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x1]: PCM

Default Amp-In caps: ofs=0x00, nsteps=0x0f, stepsize=0x05, mute=1 Default Amp-Out caps: ofs=0x7f, nsteps=0x7f, stepsize=0x02, mute=1 Node 0x02 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0x3c 0x3c]
Power: 0x0
Node 0x03 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0xff 0xff]
Power: 0x0
Node 0x04 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0xff 0xff]
Power: 0x0
Node 0x05 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out
Amp-Out caps: N/A
Amp-Out vals: [0x3c 0x3c]
Power: 0x0
Node 0x06 [Audio Input] wcaps 0x1d0541: Stereo
Power: 0x0
Connection: 1

     0x07

Node 0x07 [Audio Selector] wcaps 0x300903: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x00 0x00]
Connection: 1

     0x0e
Node 0x08 [Audio Input] wcaps 0x1d0541: Stereo
  Power: 0x0
  Connection: 1
     0x09

Node 0x09 [Audio Selector] wcaps 0x300903: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x80 0x80]
Connection: 1

     0x15

Node 0x0a [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x08173c: IN OUT HP Detect
Pin Default 0x02024110: [Jack] Line Out at Ext Front
Conn = 1/4, Color = Green
Pin-ctls: 0xc0: OUT HP
Connection: 1

     0x02

Node 0x0b [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x00:
Connection: 1

     0x04

Node 0x0c [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x00:
Connection: 1

     0x03

Node 0x0d [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x08173c: IN OUT HP Detect
Pin Default 0x02a19920: [Jack] Mic at Ext Front
Conn = 1/8, Color = Pink
Pin-ctls: 0x24: IN
Connection: 1

     0x02

Node 0x0e [Pin Complex] wcaps 0x400081: Stereo
Pincap 0x0824: IN Detect
Pin Default 0x01845121: [Jack] Line In at Ext Rear
Conn = RCA, Color = Red
Pin-ctls: 0x20: IN
Node 0x0f [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0814: OUT Detect
Pin Default 0x01045111: [Jack] Line Out at Ext Rear
Conn = RCA, Color = Red
Pin-ctls: 0x40: OUT
Connection: 1

     0x05
Node 0x10 [Audio Output] wcaps 0x40211: Stereo Digital
  PCM:
    rates [0x3e0]: 44100 48000 88200 96000 176400
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3

Node 0x11 [Pin Complex] wcaps 0x400301: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x01451112: [Jack] SPDIF Out at Ext Rear

Quoted 9 lines
Quoted 8 lines

Conn = Optical, Color = Black
Pin-ctls: 0x00:
Connection: 2

     0x10* 0x09
Node 0x12 [Audio Input] wcaps 0x140311: Stereo Digital
  PCM:
    rates [0x160]: 44100 48000 96000
    bits [0xe]: 16 20 24

=== message truncated ===

___________________________________________________________________________
Découvrez une nouvelle façon d'obtenir des réponses à toutes vos questions !
Profitez des connaissances, des opinions et des expériences des internautes sur Yahoo! Questions/Réponses
http://fr.answers.yahoo.com

Quoted 10 lines

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV

#4 lore raw

When i force model "vaio" dmesg gives :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696:
codec_mask = 0x1
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:1739: hda_codec:
model 'vaio' is selected

When i force "vaio-ar" :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696:
codec_mask = 0x1
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:1739: hda_codec:
model 'vaio-ar' is selected

What other information so you need ?

Jean-Marc

Quoted 31 lines · --- Takashi Iwai

At Tue, 23 Jan 2007 23:46:42 +0100 (CET),

Quoted 3 lines · <[email protected]> wrote:

I have tried both model. none of them works.
Is there anything I missed ?

Please elaborate what didn't work exactly. If you specified model option, the kernel messages must appear differently. If not, the model option was not passed properly by any reason.

Takashi

Quoted 17 lines
Quoted 14 lines · --- Tobin Davis

Your subsystem ID (104d:81f7) is not listed in the driver currently. The driver is configured to use the generic parser if it can't find a match.

There are two defined models for your codec (vaio, vaio-ar). Try loading the driver with one of those models as follows:
modprobe -r snd-hda-intel # remove driver
modprobe snd-hda-intel model=vaio # reload with model deffinition

Try both model deffinitions to see which works better for you. Report back your results and we'll get it added.

Thanks,

Quoted 28 lines
Quoted 7 lines
Quoted 7 lines

Tobin Davis

Quoted 3 lines · On Mon, 2007-01-22 at 22:22 +0100, [email protected] wrote:

Hi

I can't have any sound on my sony VAIO vgx-xl100 system with the

1.0.14rc2

Quoted 20 lines
Quoted 19 lines
Quoted 18 lines

build on a 2.6.18 kernel (debian)

the output of lspci -nv is :

00:1b.0 0403: 8086:27d8 (rev 01)

	Subsystem: 104d:81f7
	Flags: bus master, fast devsel, latency 0, IRQ 169
	Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>

dmesg gives :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64 ALSA

___________________________________________________________________________
Découvrez une nouvelle façon d'obtenir des réponses à toutes vos questions !
Profitez des connaissances, des opinions et des expériences des internautes sur Yahoo! Questions/Réponses
http://fr.answers.yahoo.com

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV

#5 lore raw

At Thu, 25 Jan 2007 23:20:22 +0100 (CET),

Quoted 25 lines · <[email protected]> wrote:

When i force model "vaio" dmesg gives :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696:
codec_mask = 0x1
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:1739: hda_codec:
model 'vaio' is selected

When i force "vaio-ar" :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696:
codec_mask = 0x1
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:1739: hda_codec:
model 'vaio-ar' is selected

Quoted 1 line

What other information so you need ?

The facts: What did you test and didn't work as expected?

Note that the mixer appearance should be different from the state without model option.

Takashi

Quoted 72 lines

Jean-Marc

Quoted 31 lines · --- Takashi Iwai

At Tue, 23 Jan 2007 23:46:42 +0100 (CET),

Quoted 3 lines · <[email protected]> wrote:

I have tried both model. none of them works.
Is there anything I missed ?

Please elaborate what didn't work exactly. If you specified model option, the kernel messages must appear differently. If not, the model option was not passed properly by any reason.

Takashi

Quoted 17 lines
Quoted 14 lines · --- Tobin Davis

Your subsystem ID (104d:81f7) is not listed in the driver currently. The driver is configured to use the generic parser if it can't find a match.

There are two defined models for your codec (vaio, vaio-ar). Try loading the driver with one of those models as follows:
modprobe -r snd-hda-intel # remove driver
modprobe snd-hda-intel model=vaio # reload with model deffinition

Try both model deffinitions to see which works better for you. Report back your results and we'll get it added.

Thanks,

Quoted 28 lines
Quoted 7 lines
Quoted 7 lines

Tobin Davis

Quoted 3 lines · On Mon, 2007-01-22 at 22:22 +0100, [email protected] wrote:

Hi

I can't have any sound on my sony VAIO vgx-xl100 system with the

1.0.14rc2

Quoted 20 lines
Quoted 19 lines
Quoted 18 lines

build on a 2.6.18 kernel (debian)

the output of lspci -nv is :

00:1b.0 0403: 8086:27d8 (rev 01)

	Subsystem: 104d:81f7
	Flags: bus master, fast devsel, latency 0, IRQ 169
	Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>

dmesg gives :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64 ALSA

Quoted 5 lines

___________________________________________________________________________
Découvrez une nouvelle façon d'obtenir des réponses à toutes vos questions !
Profitez des connaissances, des opinions et des expériences des internautes sur Yahoo! Questions/Réponses
http://fr.answers.yahoo.com

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV

#6 lore raw

What i have tested :
using aplay or any other player do not give any sound, with or without the model option.
e.g. aplay /usr/lib/openoffice/share/gallery/sounds/gong.wav do not give any sound in my speakers

The mixer changes when i force the model :
without "model" option : only "master" and "pcm" playback exist with "vaio" option, one "capture device appears, with 2 parameters : line-in and microphone
with "vaio-ar", two more capture devices appear : line-in and microphone.

The "master" and "pcm" device are not muted.

Is there anoter parameter i missed to unmute the sound ?

Jean-Marc

Quoted 12 lines · --- Takashi Iwai

At Thu, 25 Jan 2007 23:20:22 +0100 (CET),

Quoted 9 lines · <[email protected]> wrote:

When i force model "vaio" dmesg gives :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64 ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696:

Quoted 14 lines
Quoted 2 lines

codec_mask = 0x1
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:1739:

hda_codec:

Quoted 10 lines

model 'vaio' is selected

When i force "vaio-ar" :

ACPI: PCI interrupt for device 0000:00:1b.0 disabled
PCI: Enabling device 0000:00:1b.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64 ALSA

/home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696:

Quoted 7 lines
Quoted 2 lines

codec_mask = 0x1
ALSA /home/jm/tmp/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:1739:

hda_codec:

Quoted 3 lines

model 'vaio-ar' is selected

What other information so you need ?

Quoted 7 lines

The facts: What did you test and didn't work as expected?

Note that the mixer appearance should be different from the state without model option.

Takashi

___________________________________________________________________________
Découvrez une nouvelle façon d'obtenir des réponses à toutes vos questions !
Profitez des connaissances, des opinions et des expériences des internautes sur Yahoo! Questions/Réponses
http://fr.answers.yahoo.com

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV