PROBLEM: Kernel 2.6.26 oops if I unplug my Logitech USB 1.1 headset
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Dear kernel hackers. ;)
[1.] One line summary of the problem: If I unplug my USB-Headset the kernel oopses.
[2.] Full description of the problem/report:
If I unplug the Logitech Headset, the kernel prints the following message to /var/log/dmesg.log. I can unload the ehci module by executing "sudo rmmod ehci_hcd" but "sudo rmmod uhci_hcd" blocks infinitely and thus I suppose the Headset uses USB 1.1. "lsusb" shows the headset as
Bus 002 Device 004: ID 046d:0a01 Logitech, Inc. USB Headset
and I have no further information about the brand name or something. If I replug the headset or any other usb device it is no longer recognized by the system. I'm using a current arch linux install with KDE 4.1.1 on my Samsung R50 laptop. The above data (except the oops message) was collected after a reboot with a plugged in again and working headset.
The oops does not occur every time I unplug the headset but so far I have not been able to determine how to trigger the oops. I have tried to plug and unplug it a few times after a fresh reboot with no programs running but KDE and after four or five plugs and unplugs the kernel oopsed.
I hope this bug report helps you guys a little and this bug get's fixed at some time as it's quite annoying. ;)
[3.] Keywords (i.e., modules, networking, kernel): usb, usbcore, uhci_hcd, kernel, module, oops, crash
[4.] Kernel version (from /proc/version): Linux version 2.6.26-ARCH (root@T-POWA-LX) (gcc version 4.3.1 20080724 (prerelease) (GCC) ) #1 SMP PREEMPT Tue Aug 26 21:15:43 UTC 2008
[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)
usb 3-1: USB disconnect, address 2
BUG: unable to handle kernel paging request at 00100100 IP: [<f895f89d>] :snd:snd_ctl_dev_disconnect+0x5d/0x90 *pde = 00000000 Oops: 0000 [#1] PREEMPT SMP Modules linked in: udf crc_itu_t michael_mic arc4 ecb ieee80211_crypt_tkip ipv6
radeon drm ntfs sdhci mmc_core pcspkr yenta_socket rsrc_nonstatic serio_raw psmouse ohci1394 ieee1394 i2c_i801 i2c_core snd_usb_audio snd_usb_lib snd_rawmidi snd_hwdep usb_storage video output intel_agp agpgart sg thermal fan button battery ac cpufreq_ondemand acpi_cpufreq freq_table processor snd_intel8x0m joydev snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device evdev usblp snd_intel8x0 usbhid hid ff_memless snd_ac97_codec snd_pcm_oss snd_pcm snd_timer snd_page_alloc snd_mixer_oss snd soundcore ac97_bus ipw2200 ieee80211 ieee80211_crypt b44 ssb pcmcia pcmcia_core firmware_class mii rtc_cmos rtc_core rtc_lib ext3 jbd mbcache sr_mod sd_mod cdrom uhci_hcd ehci_hcd usbcore ata_piix ata_generic pata_acpi libata scsi_mod dock
Pid: 764, comm: khubd Not tainted (2.6.26-ARCH #1)
EIP: 0060:[<f895f89d>] EFLAGS: 00010282 CPU: 0
EIP is at snd_ctl_dev_disconnect+0x5d/0x90 [snd]
EAX: 00000000 EBX: 00100100 ECX: 00020004 EDX: 0000001d
ESI: f70f0b70 EDI: f70f0a00 EBP: f70f0b4c ESP: f7063e30
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process khubd (pid: 764, ti=f7062000 task=f7bf87e0 task.ti=f7062000)
Stack: 00000000 f7b6a020 00000000 f70f0a00 f70f0b40 f8961e96 22222222 f7b6a020
f8961eea 00000000 f70f0a00 f70f0b8c 00000000 f895e1b8 22222222 f7b5de00
f7b5de00 f8b148c0 f7b952c0 f8b03c48 f70f0a00 f7b5de00 f8b148c0 f7b5de1c
Call Trace:
[<f8961e96>] snd_device_disconnect+0x66/0x90 [snd]
[<f8961eea>] snd_device_disconnect_all+0x2a/0x50 [snd]
[<f895e1b8>] snd_card_disconnect+0x148/0x1a0 [snd]
[<f8b03c48>] usb_audio_disconnect+0x58/0x140 [snd_usb_audio]
[<f88c1470>] usb_unbind_interface+0x50/0xa0 [usbcore]
[<c026a5b5>] __device_release_driver+0x75/0xc0
[<c026a6c0>] device_release_driver+0x20/0x40
[<c0269c2a>] bus_remove_device+0x8a/0xc0
[<c026868f>] device_del+0xef/0x150
[<f88be644>] usb_disable_device+0x84/0xf0 [usbcore]
[<f88ba180>] usb_disconnect+0xa0/0x140 [usbcore]
[<f88bad03>] hub_thread+0x313/0x1170 [usbcore]
[<c013f430>] autoremove_wake_function+0x0/0x50
[<f88ba9f0>] hub_thread+0x0/0x1170 [usbcore]
[<c013f149>] kthread+0x39/0x70
[<c013f110>] kthread+0x0/0x70
[<c0104c23>] kernel_thread_helper+0x7/0x14
=======================
Code: 18 b9 01 00 00 00 ba 03 00 00 00 c7 04 24 00 00 00 00 e8 c7 30 7c c7 8d 4328 b9 04 0002 00 ba 1d 00 00 00 e8 a5 44 83 c7 8b 1b <8b> 03 0f 18 00 90 39 f3 75 c9 89 e8 e8 d2 3c 7e c7 89 fa 31 c0
EIP: [<f895f89d>] snd_ctl_dev_disconnect+0x5d/0x90 [snd] SS:ESP 0068:f7063e30
- ---[ end trace 05aa0b5534340422 ]---
[6.] A small shell script or example program which triggers the
problem (if possible)
[7.] Environment
[7.1.] Software (add the output of the ver_linux script here)
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux HEX 2.6.26-ARCH #1 SMP PREEMPT Tue Aug 26 21:15:43 UTC 2008 i686 Intel(R) Pentium(R) M processor 1.73GHz GenuineIntel GNU/Linux
Gnu C 4.3.1
Gnu make 3.81
binutils 2.18.0.20080610
util-linux 2.14
mount support
module-init-tools 3.4
e2fsprogs 1.40.8
jfsutils 1.1.12
reiserfsprogs 3.6.20
xfsprogs 2.9.8
pcmciautils 014
PPP 2.4.4
Linux C Library 2.8
Dynamic linker (ldd) 2.8
Linux C++ Library so.6.0
Procps 3.2.7
Net-tools 1.60
Kbd 1.13
Sh-utils 6.12
udev 119
wireless-tools 29
Modules Loaded michael_mic arc4 ecb ieee80211_crypt_tkipcpufreq_ondemand snd_usb_audio snd_usb_lib snd_rawmidi snd_hwdep ipv6 radeon drm ntfs joydev pcspkr serio_raw psmouse i2c_i801 i2c_core usblp sdhci ohci1394 mmc_core ieee1394 yenta_socket rsrc_nonstatic usb_storage usbhid hid ff_memless video output intel_agp agpgart sg thermal evdev fan button battery ac acpi_cpufreq freq_table processor snd_intel8x0m snd_intel8x0 snd_ac97_codec snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss snd_pcm snd_timer snd_page_alloc snd_mixer_oss snd soundcore ac97_bus ipw2200 ieee80211 ieee80211_crypt b44 ssb pcmcia pcmcia_core firmware_class mii rtc_cmos rtc_core rtc_lib ext3 jbd mbcache sr_mod cdrom sd_mod ehci_hcd uhci_hcd usbcore ata_piix ata_generic pata_acpi libata scsi_mod dock
[7.2.] Processor information (from /proc/cpuinfo):
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 13
model name : Intel(R) Pentium(R) M processor 1.73GHz
stepping : 8
cpu MHz : 1733.000
cache size : 2048 KBfdiv_bug : nohlt_bug : nof00f_bug : nocoma_bug : no
fpu : yesfpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat clflush dts acpi mmx fxsr sse sse2 ss tm pbe bts est tm2
bogomips : 3462.30
clflush size : 64
power management:
[7.3.] Module information (from /proc/modules):
michael_mic 4224 4 - Live 0xf8c4d000
arc4 3712 4 - Live 0xf8849000
ecb 4608 4 - Live 0xf8b65000ieee80211_crypt_tkip 10752 2 - Live 0xf8c49000 cpufreq_ondemand 8716 1 - Live 0xf8c3c000snd_usb_audio 81152 1 - Live 0xf94a0000snd_usb_lib 17024 1 snd_usb_audio, Live 0xf8c50000 snd_rawmidi 21504 1 snd_usb_lib, Live 0xf8b16000snd_hwdep 8964 1 snd_usb_audio, Live 0xf8b39000
ipv6 259684 63 - Live 0xf94d2000
radeon 137248 2 - Live 0xf8c60000
drm 73896 3 radeon, Live 0xf8b51000
ntfs 221664 1 - Live 0xf8b6a000
joydev 11584 0 - Live 0xf8b04000
pcspkr 4352 0 - Live 0xf8b01000serio_raw 7044 0 - Live 0xf8acc000
psmouse 38288 0 - Live 0xf8b1d000i2c_i801 10384 0 - Live 0xf8a93000i2c_core 21140 1 i2c_i801, Live 0xf8b09000
usblp 13824 0 - Live 0xf8af0000
sdhci 16388 0 - Live 0xf8a8d000
ohci1394 30128 0 - Live 0xf8ae7000mmc_core 43036 1 sdhci, Live 0xf8af5000
ieee1394 80696 1 ohci1394, Live 0xf8ab7000yenta_socket 24972 1 - Live 0xf8aaf000rsrc_nonstatic 12800 1 yenta_socket, Live 0xf8a88000 usb_storage 90560 1 - Live 0xf8acf000
usbhid 46016 0 - Live 0xf8aa2000
hid 40960 1 usbhid, Live 0xf8a97000ff_memless 6664 1 usbhid, Live 0xf8a2b000
video 18064 0 - Live 0xf8a82000
output 4608 1 video, Live 0xf8a51000intel_agp 26428 0 - Live 0xf8a67000
agpgart 29652 2 drm,intel_agp, Live 0xf8a79000
sg 28596 0 - Live 0xf8a71000
thermal 16796 0 - Live 0xf8a61000
evdev 10880 10 - Live 0xf8a56000
fan 6020 0 - Live 0xf8a2e000
button 7824 0 - Live 0xf8a1c000
battery 12036 0 - Live 0xf8a4d000
ac 6020 0 - Live 0xf8a22000acpi_cpufreq 9228 0 - Live 0xf8a27000freq_table 5568 2 cpufreq_ondemand,acpi_cpufreq, Live 0xf8a1f000 processor 33836 3 thermal,acpi_cpufreq, Live 0xf89a6000 snd_intel8x0m 15500 0 - Live 0xf89cf000snd_intel8x0 30748 1 - Live 0xf8a13000snd_ac97_codec 99748 2 snd_intel8x0m,snd_intel8x0, Live 0xf8a33000 snd_seq_oss 31872 0 - Live 0xf89b1000snd_seq_midi_event 8192 1 snd_seq_oss, Live 0xf897d000 snd_seq 49968 4 snd_seq_oss,snd_seq_midi_event, Live 0xf8a05000 snd_seq_device 8332 3 snd_rawmidi,snd_seq_oss,snd_seq, Live 0xf8979000 snd_pcm_oss 40192 0 - Live 0xf895b000snd_pcm 69636 5 snd_usb_audio,snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss, Live 0xf89bc000
snd_timer 21384 2 snd_seq,snd_pcm, Live 0xf8947000
snd_page_alloc 9608 3 snd_intel8x0m,snd_intel8x0,snd_pcm, Live 0xf8957000
snd_mixer_oss 16512 1 snd_pcm_oss, Live 0xf8916000
snd 50724 17 snd_usb_audio,snd_rawmidi,snd_hwdep,snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss, Live 0xf8967000
soundcore 8032 1 snd, Live 0xf8944000
ac97_bus 3584 1 snd_ac97_codec, Live 0xf8822000
ipw2200 142408 0 - Live 0xf8982000
ieee80211 31176 1 ipw2200, Live 0xf894e000
ieee80211_crypt 6532 2 ieee80211_crypt_tkip,ieee80211, Live 0xf88e4000
b44 26512 0 - Live 0xf893c000
ssb 39684 1 b44, Live 0xf88f6000
pcmcia 34476 1 ssb, Live 0xf890c000
pcmcia_core 34708 4 yenta_socket,rsrc_nonstatic,ssb,pcmcia, Live 0xf8902000
firmware_class 9088 2 ipw2200,pcmcia, Live 0xf88dc000
mii 6528 1 b44, Live 0xf88d9000rtc_cmos 11424 0 - Live 0xf888c000rtc_core 17436 1 rtc_cmos, Live 0xf887c000rtc_lib 4480 1 rtc_core, Live 0xf8846000
ext3 125704 3 - Live 0xf891c000
jbd 45716 1 ext3, Live 0xf88e9000
mbcache 8708 1 ext3, Live 0xf8842000sr_mod 16836 0 - Live 0xf8876000
cdrom 36128 1 sr_mod, Live 0xf8882000sd_mod 25240 7 - Live 0xf886e000ehci_hcd 35596 0 - Live 0xf8864000uhci_hcd 23952 0 - Live 0xf8831000
usbcore 132080 8 snd_usb_audio,snd_usb_lib,usblp,usb_storage,usbhid,ehci_hcd,uhci_hcd, Live 0xf88b7000ata_piix 17924 4 - Live 0xf8839000ata_generic 6788 0 - Live 0xf882e000pata_acpi 6016 0 - Live 0xf882b000
libata 150048 3 ata_piix,ata_generic,pata_acpi, Live 0xf8891000 scsi_mod 95692 5 usb_storage,sg,sr_mod,sd_mod,libata, Live 0xf884b000 dock 9488 1 libata, Live 0xf8827000
[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
$ cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0070-0077 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:1f.1
0170-0177 : ata_piix
01f0-01f7 : 0000:00:1f.1
01f0-01f7 : ata_piix
0376-0376 : 0000:00:1f.1
0376-0376 : ata_piix
03c0-03df : vga+
03f6-03f6 : 0000:00:1f.1
03f6-03f6 : ata_piix
0680-06ff : pnp 00:06
0800-080f : pnp 00:06
0900-090f : pnp 00:06
0cf8-0cff : PCI conf1
1000-107f : 0000:00:1f.0
1000-107f : pnp 00:06
1000-1003 : ACPI PM1a_EVT_BLK
1004-1005 : ACPI PM1a_CNT_BLK
1008-100b : ACPI PM_TMR
1010-1015 : ACPI CPU throttle
1020-1020 : ACPI PM2_CNT_BLK
1028-102f : ACPI GPE0_BLK1180-11bf : 0000:00:1f.0
1180-11bf : pnp 00:06
1640-164f : pnp 00:06
1800-181f : 0000:00:1d.0
1800-181f : uhci_hcd
1820-183f : 0000:00:1d.1
1820-183f : uhci_hcd
1840-185f : 0000:00:1d.2
1840-185f : uhci_hcd
1860-187f : 0000:00:1d.3
1860-187f : uhci_hcd
1880-18bf : 0000:00:1e.2
1880-18bf : Intel ICH6
18c0-18cf : 0000:00:1f.1
18c0-18cf : ata_piix
18e0-18ff : 0000:00:1f.3
18e0-18ff : i801_smbus
1c00-1cff : 0000:00:1e.2
1c00-1cff : Intel ICH6
2000-207f : 0000:00:1e.3
2000-207f : Intel ICH6 Modem
2400-24ff : 0000:00:1e.3
2400-24ff : Intel ICH6 Modem
3000-3fff : PCI Bus 0000:01
3000-30ff : 0000:01:00.0
4000-4fff : PCI Bus 0000:02
5000-5fff : PCI Bus 0000:06
5000-50ff : PCI CardBus 0000:07
5400-54ff : PCI CardBus 0000:07
$ cat /proc/iomem
00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000ce1ff : Video ROM
000d0000-000d3fff : Adapter ROM
000d4000-000d4fff : Adapter ROM
000f0000-000fffff : System ROM
00100000-3fe9ffff : System RAM
00100000-0031211d : Kernel code
0031211e-003cc37f : Kernel data
00415000-004e527f : Kernel bss
3fea0000-3feb0fff : ACPI Tables
3feb1000-3fefffff : ACPI Non-volatile Storage
3ff00000-3fffffff : reserved
50000000-53ffffff : PCI CardBus 0000:07
54000000-543fffff : PCI CardBus 0000:07
c0000000-c00003ff : 0000:00:1d.7
c0000000-c00003ff : ehci_hcd
c0000400-c00004ff : 0000:00:1e.2
c0000400-c00004ff : Intel ICH6
c0000800-c00009ff : 0000:00:1e.2
c0000800-c00009ff : Intel ICH6
c0100000-c01fffff : PCI Bus 0000:01
c0100000-c010ffff : 0000:01:00.0
c0120000-c013ffff : 0000:01:00.0
c4000000-c7ffffff : PCI Bus 0000:02
c8000000-c80fffff : PCI Bus 0000:06
c8000000-c8000fff : 0000:06:07.0
c8000000-c8000fff : ipw2200
c8001000-c80017ff : 0000:06:09.1
c8001000-c80017ff : ohci1394
c8001800-c80018ff : 0000:06:09.2
c8001800-c80018ff : mmc0
c8001c00-c8001cff : 0000:06:09.3
c8002000-c80020ff : 0000:06:09.4
c8003000-c8003fff : 0000:06:09.0
c8003000-c8003fff : yenta_socket
c8004000-c8005fff : 0000:06:05.0
c8004000-c8005fff : 0000:06:05.0d0000000-d7ffffff : PCI Bus 0000:01
d0000000-d7ffffff : 0000:01:00.0
d8000000-dbffffff : PCI Bus 0000:02
e0000000-f0005fff : reserved
e0000000-efffffff : PCI MMCONFIG 0
f0008000-f000bfff : reserved
fed00000-fed003ff : HPET 0
fed00000-fed003ff : reserved
fed20000-fed8ffff : reserved
ff000000-ffffffff : reserved
[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: intel-agp
00:01.0 PCI bridge: Intel Corporation Mobile 915GM/PM Express PCI Express Root Port (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: c0100000-c01fffff
Prefetchable memory behind bridge: d0000000-d7ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Samsung Electronics Co Ltd Device b035
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [a0] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1
<1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency
L0 <256ns, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surpise-
Slot # 1, PowerLimit 75.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Capabilities: [140] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: c4000000-c7ffffff
Prefetchable memory behind bridge: 00000000d8000000-00000000dbffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag+ RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0 <1us, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+
Surpise+
Slot # 2, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: Samsung Electronics Co Ltd Device b035
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mAPME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=0a, sec-latency=32
I/O behind bridge: 00005000-00005fff
Memory behind bridge: c8000000-c80fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Gammagraphx, Inc. Device 0000
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 1880 [size=64]
Region 2: Memory at c0000800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at c0000400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mAPME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03) (prog-if 00 [Generic])
Subsystem: Samsung Electronics Co Ltd Device 2115
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mAPME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Intel ICH Modem
Kernel modules: snd-intel8x0m
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: intel-rng
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 18c0 [size=16]
Kernel driver in use: ata_piix
Kernel modules: ata_piix, piix00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 18e0 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility X700 (PCIE) (prog-if 00 [VGA controller])
Subsystem: Samsung Electronics Co Ltd Device e003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at c0120000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns,
L1 <4us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency
L0 <256ns, L1 <2us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [100] Advanced Error Reporting <?>
06:05.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 22
Region 0: Memory at c8004000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: b44
Kernel modules: b44
06:07.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
Subsystem: Intel Corporation Samsung P35 integrated WLAN
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at c8000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mAPME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Kernel driver in use: ipw2200
Kernel modules: ipw2200
06:09.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c8003000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 54000000-543ff000 (prefetchable)
Memory window 1: 50000000-53fff000
I/O window 0: 00005000-000050ff
I/O window 1: 00005400-000054ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket06:09.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 08) (prog-if 10 [OHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin B routed to IRQ 17
Region 0: Memory at c8001000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
06:09.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 17)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin C routed to IRQ 18
Region 0: Memory at c8001800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sdhci
Kernel modules: sdhci
06:09.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 08)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 255
Region 0: Memory at c8001c00 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
06:09.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 03)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 255
Region 0: Memory at c8002000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
[7.6.] SCSI information (from /proc/scsi/scsi)
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: SAMSUNG HM120JC Rev: YL10
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: TEAC Model: DV-W28EA Rev: S.0A
Type: CD-ROM ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: WDC WD25 Model: 00BB-00GUC0 Rev: 0811
Type: Direct-Access ANSI SCSI revision: 00
Host: scsi3 Channel: 00 Id: 00 Lun: 00
Vendor: HDT72252 Model: 5DLAT80 Rev: V44O
Type: Direct-Access ANSI SCSI revision: 00
[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you think to be relevant):
I hope this helps you fix my problem. :)
Edgar Kalkowski
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
iEYEARECAAYFAkjAaasACgkQ6s03tsVZHYGergCdFFqvhSRKhTO7zkyBDaMwU+20 ge0An2GoI9GBF16OBpKOkN+2y/TrAzG6
=feLy
-----END PGP SIGNATURE-----
Quoted 3 lines · On Fri, 05 Sep 2008 01:05:21 +0200 Edgar Kalkowski <[email protected]>…
Dear kernel hackers. ;)
[1.] One line summary of the problem: If I unplug my USB-Headset the kernel oopses.
cc's added.
Might be USB, might be ALSA.
Quoted 1,179 lines
[2.] Full description of the problem/report:
If I unplug the Logitech Headset, the kernel prints the following message to/var/log/dmesg.log. I can unload the ehci module by executing "sudo rmmodehci_hcd" but "sudo rmmoduhci_hcd" blocks infinitely and thus I suppose the Headset uses USB 1.1. "lsusb" shows the headset asBus 002 Device 004: ID 046d:0a01 Logitech, Inc. USB Headset
and I have no further information about the brand name or something. If I replug the headset or any other usb device it is no longer recognized by the system. I'm using a current arch linux install with KDE 4.1.1 on my Samsung R50 laptop. The above data (except the oops message) was collected after a reboot with a plugged in again and working headset.
The oops does not occur every time I unplug the headset but so far I have not been able to determine how to trigger the oops. I have tried to plug and unplug it a few times after a fresh reboot with no programs running but KDE and after four or five plugs and unplugs the kernel oopsed.
I hope this bug report helps you guys a little and this bug get's fixed at some time as it's quite annoying. ;)
[3.] Keywords (i.e., modules, networking, kernel): usb, usbcore,
uhci_hcd, kernel, module, oops, crash[4.] Kernel version (from
/proc/version): Linux version 2.6.26-ARCH (root@T-POWA-LX) (gcc version 4.3.1 20080724 (prerelease) (GCC) ) #1 SMP PREEMPT Tue Aug 26 21:15:43 UTC 2008[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (seeDocumentation/oops-tracing.txt)usb 3-1: USB disconnect, address 2
BUG: unable to handle kernel paging request at 00100100 IP: [<f895f89d>] :snd:snd_ctl_dev_disconnect+0x5d/0x90 *pde = 00000000 Oops: 0000 [#1] PREEMPT SMP Modules linked in: udf crc_itu_t michael_mic arc4 ecb ieee80211_crypt_tkip ipv6radeon drm ntfs sdhci
mmc_corepcspkryenta_socketrsrc_nonstaticserio_rawpsmouse ohci1394 ieee1394i2c_i801i2c_coresnd_usb_audiosnd_usb_libsnd_rawmidisnd_hwdepusb_storagevideo outputintel_agpagpgart sg thermal fan button battery accpufreq_ondemandacpi_cpufreqfreq_tableprocessorsnd_intel8x0mjoydevsnd_seq_osssnd_seq_midi_eventsnd_seqsnd_seq_deviceevdev usblpsnd_intel8x0usbhid hidff_memlesssnd_ac97_codecsnd_pcm_osssnd_pcmsnd_timersnd_page_allocsnd_mixer_osssnd soundcoreac97_busipw2200 ieee80211ieee80211_cryptb44 ssb pcmciapcmcia_corefirmware_classmiirtc_cmosrtc_corertc_libext3 jbd mbcachesr_modsd_modcdromuhci_hcdehci_hcdusbcoreata_piixata_genericpata_acpilibatascsi_moddockPid: 764, comm: khubd Not tainted (2.6.26-ARCH #1)
EIP: 0060:[<f895f89d>] EFLAGS: 00010282 CPU: 0
EIP is atsnd_ctl_dev_disconnect+0x5d/0x90[snd]
EAX: 00000000 EBX: 00100100 ECX: 00020004 EDX:0000001d
ESI:f70f0b70EDI:f70f0a00EBP:f70f0b4cESP:f7063e30
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process khubd (pid: 764, ti=f7062000 task=f7bf87e0 task.ti=f7062000)Stack: 00000000 f7b6a020 00000000 f70f0a00 f70f0b40 f8961e96 22222222 f7b6a020 f8961eea 00000000 f70f0a00 f70f0b8c 00000000 f895e1b8 22222222 f7b5de00 f7b5de00 f8b148c0 f7b952c0 f8b03c48 f70f0a00 f7b5de00 f8b148c0 f7b5de1c Call Trace: [<f8961e96>] snd_device_disconnect+0x66/0x90 [snd] [<f8961eea>] snd_device_disconnect_all+0x2a/0x50 [snd] [<f895e1b8>] snd_card_disconnect+0x148/0x1a0 [snd] [<f8b03c48>] usb_audio_disconnect+0x58/0x140 [snd_usb_audio] [<f88c1470>] usb_unbind_interface+0x50/0xa0 [usbcore] [<c026a5b5>] __device_release_driver+0x75/0xc0 [<c026a6c0>] device_release_driver+0x20/0x40 [<c0269c2a>] bus_remove_device+0x8a/0xc0 [<c026868f>] device_del+0xef/0x150 [<f88be644>] usb_disable_device+0x84/0xf0 [usbcore] [<f88ba180>] usb_disconnect+0xa0/0x140 [usbcore] [<f88bad03>] hub_thread+0x313/0x1170 [usbcore] [<c013f430>] autoremove_wake_function+0x0/0x50 [<f88ba9f0>] hub_thread+0x0/0x1170 [usbcore] [<c013f149>] kthread+0x39/0x70 [<c013f110>] kthread+0x0/0x70 [<c0104c23>] kernel_thread_helper+0x7/0x14 ======================= Code: 18 b9 01 00 00 00 ba 03 00 00 00 c7 04 24 00 00 00 00 e8 c7 30 7c c7 8d 4328 b9 04 0002 00 ba 1d 00 00 00 e8 a5 44 83 c7 8b 1b <8b> 03 0f 18 00 90 39 f3 75 c9 89 e8 e8 d2 3c 7e c7 89 fa 31 c0
EIP: [<f895f89d>]snd_ctl_dev_disconnect+0x5d/0x90[snd] SS:ESP 0068:f7063e30
- ---[ end trace05aa0b5534340422]---[6.] A small shell script or example program which triggers the
problem (if possible)[7.] Environment
[7.1.] Software (add the output of thever_linuxscript here)If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in
Documentation/Changes.Linux HEX 2.6.26-ARCH #1 SMP PREEMPT Tue Aug 26 21:15:43 UTC 2008 i686 Intel(R) Pentium(R) M processor 1.73GHz GenuineIntel GNU/Linux
Gnu C 4.3.1
Gnu make 3.81
binutils 2.18.0.20080610
util-linux 2.14
mount support
module-init-tools 3.4
e2fsprogs 1.40.8
jfsutils 1.1.12
reiserfsprogs 3.6.20
xfsprogs 2.9.8
pcmciautils 014
PPP 2.4.4
Linux C Library 2.8
Dynamic linker (ldd) 2.8
Linux C++ Library so.6.0
Procps 3.2.7
Net-tools 1.60
Kbd 1.13
Sh-utils 6.12
udev 119
wireless-tools 29
Modules Loaded
michael_micarc4 ecbieee80211_crypt_tkipcpufreq_ondemandsnd_usb_audiosnd_usb_libsnd_rawmidisnd_hwdepipv6 radeon drm ntfs joydev pcspkrserio_rawpsmousei2c_i801i2c_coreusblp sdhci ohci1394mmc_coreieee1394yenta_socketrsrc_nonstaticusb_storageusbhid hidff_memlessvideo outputintel_agpagpgart sg thermal evdev fan button battery acacpi_cpufreqfreq_tableprocessorsnd_intel8x0msnd_intel8x0snd_ac97_codecsnd_seq_osssnd_seq_midi_eventsnd_seqsnd_seq_devicesnd_pcm_osssnd_pcmsnd_timersnd_page_allocsnd_mixer_osssnd soundcoreac97_busipw2200 ieee80211ieee80211_cryptb44 ssb pcmciapcmcia_corefirmware_classmiirtc_cmosrtc_corertc_libext3 jbd mbcachesr_modcdromsd_modehci_hcduhci_hcdusbcoreata_piixata_genericpata_acpilibatascsi_moddock[7.2.] Processor information (from
/proc/cpuinfo):processor : 0
vendor_id: GenuineIntelcpu family : 6
model : 13
model name : Intel(R) Pentium(R) M processor 1.73GHz
stepping : 8
cpu MHz : 1733.000
cache size : 2048 KBfdiv_bug: nohlt_bug: nof00f_bug: nocoma_bug: no
fpu : yesfpu_exception: yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat clflush dts acpi mmx fxsr sse sse2 ss tm pbe bts est tm2
bogomips : 3462.30
clflush size : 64
power management:[7.3.] Module information (from
/proc/modules):
michael_mic4224 4 - Live0xf8c4d000
arc4 3712 4 - Live0xf8849000
ecb 4608 4 - Live0xf8b65000ieee80211_crypt_tkip10752 2 - Live0xf8c49000cpufreq_ondemand8716 1 - Live0xf8c3c000snd_usb_audio81152 1 - Live0xf94a0000snd_usb_lib17024 1snd_usb_audio, Live0xf8c50000snd_rawmidi21504 1snd_usb_lib, Live0xf8b16000snd_hwdep8964 1snd_usb_audio, Live0xf8b39000
ipv6 259684 63 - Live0xf94d2000
radeon 137248 2 - Live0xf8c60000
drm 73896 3 radeon, Live0xf8b51000
ntfs 221664 1 - Live0xf8b6a000
joydev 11584 0 - Live0xf8b04000
pcspkr 4352 0 - Live0xf8b01000serio_raw7044 0 - Live0xf8acc000
psmouse 38288 0 - Live0xf8b1d000i2c_i80110384 0 - Live0xf8a93000i2c_core21140 1i2c_i801, Live0xf8b09000
usblp 13824 0 - Live0xf8af0000
sdhci 16388 0 - Live0xf8a8d000
ohci1394 30128 0 - Live0xf8ae7000mmc_core43036 1 sdhci, Live0xf8af5000
ieee1394 80696 1 ohci1394, Live0xf8ab7000yenta_socket24972 1 - Live0xf8aaf000rsrc_nonstatic12800 1yenta_socket, Live0xf8a88000usb_storage90560 1 - Live0xf8acf000
usbhid 46016 0 - Live0xf8aa2000
hid 40960 1 usbhid, Live0xf8a97000ff_memless6664 1 usbhid, Live0xf8a2b000
video 18064 0 - Live0xf8a82000
output 4608 1 video, Live0xf8a51000intel_agp26428 0 - Live0xf8a67000
agpgart 29652 2 drm,intel_agp, Live0xf8a79000
sg 28596 0 - Live0xf8a71000
thermal 16796 0 - Live0xf8a61000
evdev 10880 10 - Live0xf8a56000
fan 6020 0 - Live0xf8a2e000
button 7824 0 - Live0xf8a1c000
battery 12036 0 - Live0xf8a4d000
ac 6020 0 - Live0xf8a22000acpi_cpufreq9228 0 - Live0xf8a27000freq_table5568 2 cpufreq_ondemand,acpi_cpufreq, Live0xf8a1f000processor 33836 3 thermal,acpi_cpufreq, Live0xf89a6000snd_intel8x0m15500 0 - Live0xf89cf000snd_intel8x030748 1 - Live0xf8a13000snd_ac97_codec99748 2 snd_intel8x0m,snd_intel8x0, Live0xf8a33000snd_seq_oss31872 0 - Live0xf89b1000snd_seq_midi_event8192 1snd_seq_oss, Live0xf897d000snd_seq49968 4 snd_seq_oss,snd_seq_midi_event, Live0xf8a05000snd_seq_device8332 3 snd_rawmidi,snd_seq_oss,snd_seq, Live0xf8979000snd_pcm_oss40192 0 - Live0xf895b000snd_pcm69636 5 snd_usb_audio,snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss, Live0xf89bc000
snd_timer21384 2 snd_seq,snd_pcm, Live0xf8947000
snd_page_alloc9608 3 snd_intel8x0m,snd_intel8x0,snd_pcm, Live0xf8957000
snd_mixer_oss16512 1snd_pcm_oss, Live0xf8916000snd 50724 17 snd_usb_audio,snd_rawmidi,snd_hwdep,snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss, Live
0xf8967000
soundcore 8032 1 snd, Live0xf8944000
ac97_bus3584 1snd_ac97_codec, Live0xf8822000ipw2200 142408 0 - Live
0xf8982000ieee80211 31176 1 ipw2200, Live
0xf894e000
ieee80211_crypt6532 2 ieee80211_crypt_tkip,ieee80211, Live0xf88e4000b44 26512 0 - Live
0xf893c000ssb 39684 1 b44, Live
0xf88f6000pcmcia 34476 1 ssb, Live
0xf890c000
pcmcia_core34708 4 yenta_socket,rsrc_nonstatic,ssb,pcmcia, Live0xf8902000
firmware_class9088 2 ipw2200,pcmcia, Live0xf88dc000mii 6528 1 b44, Live
0xf88d9000rtc_cmos11424 0 - Live0xf888c000rtc_core17436 1rtc_cmos, Live0xf887c000rtc_lib4480 1rtc_core, Live0xf8846000
ext3 125704 3 - Live0xf891c000
jbd 45716 1 ext3, Live0xf88e9000
mbcache 8708 1 ext3, Live0xf8842000sr_mod16836 0 - Live0xf8876000
cdrom 36128 1sr_mod, Live0xf8882000sd_mod25240 7 - Live0xf886e000ehci_hcd35596 0 - Live0xf8864000uhci_hcd23952 0 - Live0xf8831000
usbcore 132080 8 snd_usb_audio,snd_usb_lib,usblp,usb_storage,usbhid,ehci_hcd,uhci_hcd, Live0xf88b7000ata_piix17924 4 - Live0xf8839000ata_generic6788 0 - Live0xf882e000pata_acpi6016 0 - Live0xf882b000
libata 150048 3 ata_piix,ata_generic,pata_acpi, Live0xf8891000scsi_mod95692 5 usb_storage,sg,sr_mod,sd_mod,libata, Live0xf884b000dock 9488 1 libata, Live0xf8827000[7.4.] Loaded driver and hardware information (
/proc/ioports,/proc/iomem)$ cat /proc/ioports0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0070-0077 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:1f.1
0170-0177 :
ata_piix01f0-01f7 : 0000:00:1f.1
01f0-01f7 :
ata_piix0376-0376 : 0000:00:1f.1
0376-0376 :
ata_piix03c0-03df : vga+
03f6-03f6 : 0000:00:1f.1
03f6-03f6 :
ata_piix0680-06ff : pnp 00:06
0800-080f : pnp 00:06
0900-090f : pnp 00:06
0cf8-0cff : PCI conf1
1000-107f : 0000:00:1f.0
1000-107f : pnp 00:06
1000-1003 : ACPI PM1a_EVT_BLK 1004-1005 : ACPI PM1a_CNT_BLK 1008-100b : ACPI PM_TMR 1010-1015 : ACPI CPU throttle 1020-1020 : ACPI PM2_CNT_BLK 1028-102f : ACPI GPE0_BLK1180-11bf : 0000:00:1f.0
1180-11bf : pnp 00:06
1640-164f : pnp 00:06
1800-181f : 0000:00:1d.0
1800-181f :
uhci_hcd1820-183f : 0000:00:1d.1
1820-183f :
uhci_hcd1840-185f : 0000:00:1d.2
1840-185f :
uhci_hcd1860-187f : 0000:00:1d.3
1860-187f :uhci_hcd
1880-18bf : 0000:00:1e.2
1880-18bf : Intel ICH6
18c0-18cf : 0000:00:1f.1
18c0-18cf :ata_piix
18e0-18ff : 0000:00:1f.3
18e0-18ff :i801_smbus
1c00-1cff : 0000:00:1e.2
1c00-1cff : Intel ICH6
2000-207f : 0000:00:1e.3
2000-207f : Intel ICH6 Modem
2400-24ff : 0000:00:1e.3
2400-24ff : Intel ICH6 Modem
3000-3fff : PCI Bus 0000:01
3000-30ff : 0000:01:00.0
4000-4fff : PCI Bus 0000:02
5000-5fff : PCI Bus 0000:06
5000-50ff : PCI CardBus 0000:07
5400-54ff : PCI CardBus 0000:07$ cat /proc/iomem00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000ce1ff : Video ROM
000d0000-000d3fff : Adapter ROM
000d4000-000d4fff : Adapter ROM
000f0000-000fffff : System ROM
00100000-3fe9ffff : System RAM
00100000-0031211d : Kernel code
0031211e-003cc37f : Kernel data
00415000-004e527f : Kernel bss
3fea0000-3feb0fff : ACPI Tables
3feb1000-3fefffff : ACPI Non-volatile Storage
3ff00000-3fffffff : reserved
50000000-53ffffff : PCI CardBus 0000:07
54000000-543fffff : PCI CardBus 0000:07
c0000000-c00003ff : 0000:00:1d.7
c0000000-c00003ff :ehci_hcd
c0000400-c00004ff : 0000:00:1e.2
c0000400-c00004ff : Intel ICH6
c0000800-c00009ff : 0000:00:1e.2
c0000800-c00009ff : Intel ICH6
c0100000-c01fffff : PCI Bus 0000:01
c0100000-c010ffff : 0000:01:00.0
c0120000-c013ffff : 0000:01:00.0
c4000000-c7ffffff : PCI Bus 0000:02
c8000000-c80fffff : PCI Bus 0000:06
c8000000-c8000fff : 0000:06:07.0c8000000-c8000fff : ipw2200 c8001000-c80017ff : 0000:06:09.1 c8001000-c80017ff : ohci1394 c8001800-c80018ff : 0000:06:09.2 c8001800-c80018ff : mmc0 c8001c00-c8001cff : 0000:06:09.3 c8002000-c80020ff : 0000:06:09.4 c8003000-c8003fff : 0000:06:09.0 c8003000-c8003fff : yenta_socket c8004000-c8005fff : 0000:06:05.0 c8004000-c8005fff : 0000:06:05.0d0000000-d7ffffff : PCI Bus 0000:01
d0000000-d7ffffff : 0000:01:00.0
d8000000-dbffffff : PCI Bus 0000:02
e0000000-f0005fff : reserved
e0000000-efffffff : PCI MMCONFIG 0
f0008000-f000bfff : reserved
fed00000-fed003ff : HPET 0
fed00000-fed003ff : reserved
fed20000-fed8ffff : reserved
ff000000-ffffffff : reserved[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: intel-agp
00:01.0 PCI bridge: Intel Corporation Mobile 915GM/PM Express PCI Express Root Port (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: c0100000-c01fffff
Prefetchable memory behind bridge: d0000000-d7ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Samsung Electronics Co Ltd Device b035
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000Capabilities: [a0] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1
<1us
ExtTag- RBE- FLReset-DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency
L0 <256ns, L1 <4usClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surpise-
Slot # 1, PowerLimit 75.000000; Interlock- NoCompl-SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState-RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Capabilities: [140] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: c4000000-c7ffffff Prefetchable memory behind bridge: 00000000d8000000-00000000dbffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimitedExtTag+ RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0 <1us, L1 <4usClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+
Surpise+
Slot # 2, PowerLimit 6.500000; Interlock- NoCompl-SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet- LinkState-RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000Capabilities: [90] Subsystem: Samsung Electronics Co Ltd Device b035
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1800 [size=32]
Kernel driver in use:
uhci_hcdKernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use:
uhci_hcdKernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use:
uhci_hcdKernel modules: uhci-hcd
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use:
uhci_hcdKernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at
c0000000(32-bit, non-prefetchable) [size=1K]Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use:
ehci_hcdKernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-Latency: 0 Bus: primary=00, secondary=06, subordinate=0a, sec-latency=32 I/O behind bridge: 00005000-00005fff Memory behind bridge: c8000000-c80fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Gammagraphx, Inc. Device 0000
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 0 Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at 1c00 [size=256] Region 1: I/O ports at 1880 [size=64] Region 2: Memory at c0000800 (32-bit, non-prefetchable) [size=512] Region 3: Memory at c0000400 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03) (prog-if 00 [Generic])
Subsystem: Samsung Electronics Co Ltd Device 2115
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 0
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-Kernel driver in use: Intel ICH Modem
Kernel modules: snd-intel8x0m
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 0
Kernel modules: intel-rng
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at 18c0 [size=16] Kernel driver in use: ata_piix Kernel modules: ata_piix, piix00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 18e0 [size=32]
Kernel driver in use:
i801_smbusKernel modules: i2c-i801
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility X700 (PCIE) (prog-if 00 [VGA controller])
Subsystem: Samsung Electronics Co Ltd Device e003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at
d0000000(32-bit, prefetchable) [size=128M]Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at
c0100000(32-bit, non-prefetchable) [size=64K][virtual] Expansion ROM at
c0120000[disabled] [size=128K]Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-Capabilities: [58] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns,
L1 <4us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency
L0 <256ns, L1 <2usClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000Capabilities: [100] Advanced Error Reporting <?>
06:05.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-Latency: 32
Interrupt: pin A routed to IRQ 22
Region 0: Memory at
c8004000(32-bit, non-prefetchable) [size=8K]Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-Kernel driver in use: b44
Kernel modules: b44
06:07.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
Subsystem: Intel Corporation Samsung P35 integrated WLANControl: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 32 (750ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at
c8000000(32-bit, non-prefetchable) [size=4K]Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-Kernel driver in use: ipw2200
Kernel modules: ipw2200
06:09.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 168 Interrupt: pin A routed to IRQ 16 Region 0: Memory at c8003000 (32-bit, non-prefetchable) [size=4K] Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176 Memory window 0: 54000000-543ff000 (prefetchable) Memory window 1: 50000000-53fff000 I/O window 0: 00005000-000050ff I/O window 1: 00005400-000054ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 Kernel driver in use: yenta_cardbus Kernel modules: yenta_socket06:09.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 08) (prog-if 10 [OHCI])
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 64 (500ns min, 1000ns max)
Interrupt: pin B routed to IRQ 17
Region 0: Memory at
c8001000(32-bit, non-prefetchable) [size=2K]Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+Kernel driver in use: ohci1394
Kernel modules: ohci1394
06:09.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 17)
Subsystem: Samsung Electronics Co Ltd Device b035Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-Latency: 32
Interrupt: pin C routed to IRQ 18
Region 0: Memory at
c8001800(32-bit, non-prefetchable) [size=256]Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-Kernel driver in use: sdhci
Kernel modules: sdhci
06:09.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 08)
Subsystem: Samsung Electronics Co Ltd Device b035Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 255
Region 0: Memory atc8001c00(32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-06:09.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 03)
Subsystem: Samsung Electronics Co Ltd Device b035
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 255
Region 0: Memory atc8002000(32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-[7.6.] SCSI information (from
/proc/scsi/scsi)Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: SAMSUNG HM120JC Rev: YL10
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: TEAC Model: DV-W28EA Rev: S.0A
Type: CD-ROM ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: WDC WD25 Model: 00BB-00GUC0 Rev: 0811
Type: Direct-Access ANSI SCSI revision: 00
Host: scsi3 Channel: 00 Id: 00 Lun: 00
Vendor: HDT72252 Model: 5DLAT80 Rev: V44O
Type: Direct-Access ANSI SCSI revision: 00[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you think to be relevant):I hope this helps you fix my problem. :)
At Thu, 4 Sep 2008 17:28:22 -0700,
Quoted 11 lines · Andrew Morton
Quoted 3 lines · On Fri, 05 Sep 2008 01:05:21 +0200 Edgar Kalkowski <[email protected]>…
Dear kernel hackers. ;)
[1.] One line summary of the problem: If I unplug my USB-Headset the kernel oopses.
cc's added.
Might be USB, might be ALSA.
Hm, it's hard to guess...
Edgar, could you check whether it happens with 2.6.25?
thanks,
Takashi
Quoted 8 lines · Takashi Iwai
At Thu, 4 Sep 2008 17:28:22 -0700,
Quoted 6 lines · Andrew Morton
Quoted 2 lines · On Fri, 05 Sep 2008 01:05:21 +0200 Edgar Kalkowski <[email protected]>…
Dear kernel hackers. ;)
Quoted 8 lines
Quoted 5 lines
Quoted 1 line
[1.] One line summary of the problem: If I unplug my USB-Headset the kernel oopses.
cc's added.
Might be USB, might be ALSA.
Hm, it's hard to guess...
Edgar, could you check whether it happens with 2.6.25?
Hi,
I recognize this address:
Quoted 1 line
Quoted 1 line
Quoted 1 line
BUG: unable to handle kernel paging request at 00100100
Is this a magic value? I also got it, see for example:
http://lkml.org/lkml/2008/8/21/426
Google will also recognize it:
http://www.google.com/search?hl=en&q="unable+to+handle+kernel+paging+request"+00100100
Where does it come from?
Vegard
Signature · 4 lines
"The animistic metaphor of the bug that maliciously sneaked in while the programmer was not looking is intellectually dishonest as it disguises that the error is the programmer's own creation." -- E. W. Dijkstra, EWD1036
Quoted 24 lines · Vegard Nossum
Quoted 8 lines · Takashi Iwai
At Thu, 4 Sep 2008 17:28:22 -0700,
Quoted 6 lines · Andrew Morton
Quoted 2 lines · On Fri, 05 Sep 2008 01:05:21 +0200 Edgar Kalkowski <[email protected]>…
Dear kernel hackers. ;)
Quoted 8 lines
Quoted 5 lines
Quoted 1 line
[1.] One line summary of the problem: If I unplug my USB-Headset the kernel oopses.
cc's added.
Might be USB, might be ALSA.
Hm, it's hard to guess...
Edgar, could you check whether it happens with 2.6.25?Hi,
I recognize this address:
Quoted 1 line
Quoted 1 line
Quoted 1 line
BUG: unable to handle kernel paging request at 00100100
Quoted 7 lines
Is this a magic value? I also got it, see for example:
http://lkml.org/lkml/2008/8/21/426Google will also recognize it:
http://www.google.com/search?hl=en&q="unable+to+handle+kernel+paging+request"+00100100Where does it come from?
Oh. It _is_ LIST_POISON1. Sorry for the bit of noise.
Vegard
Signature · 4 lines
"The animistic metaphor of the bug that maliciously sneaked in while the programmer was not looking is intellectually dishonest as it disguises that the error is the programmer's own creation." -- E. W. Dijkstra, EWD1036
Quoted 28 lines · Vegard Nossum
Quoted 27 lines · Vegard Nossum
Quoted 8 lines · Takashi Iwai
At Thu, 4 Sep 2008 17:28:22 -0700,
Quoted 6 lines · Andrew Morton
Quoted 2 lines · On Fri, 05 Sep 2008 01:05:21 +0200 Edgar Kalkowski <[email protected]>…
Dear kernel hackers. ;)
Quoted 8 lines
Quoted 5 lines
Quoted 1 line
[1.] One line summary of the problem: If I unplug my USB-Headset the kernel oopses.
cc's added.
Might be USB, might be ALSA.
Hm, it's hard to guess...
Edgar, could you check whether it happens with 2.6.25?Hi,
I recognize this address:
Quoted 1 line
Quoted 1 line
Quoted 1 line
BUG: unable to handle kernel paging request at 00100100Is this a magic value? I also got it, see for example:
http://lkml.org/lkml/2008/8/21/426
Quoted 6 lines
Quoted 4 lines
Google will also recognize it:
http://www.google.com/search?hl=en&q="unable+to+handle+kernel+paging+request"+00100100Where does it come from?
Oh. It _is_
LIST_POISON1. Sorry for the bit of noise.
Probably totally unrelated, but I couldn't help to find this bit of code somewhat odd. In snd_ctl_dev_disconnect():
down_read(&card->controls_rwsem);
list_for_each_entry(ctl, &card->ctl_files, list) {
wake_up(&ctl->change_sleep);
kill_fasync(&ctl->fasync, SIGIO, POLL_ERR);
}
up_read(&card->controls_rwsem);...shouldn't that be using &card->ctl_files_rwlock instead of &card->controls_rwsem? That one is always used to protect the list ops on &card->ctl_files in all the other places. Or maybe it is already locked from higher ups?
Vegard
Signature · 4 lines
"The animistic metaphor of the bug that maliciously sneaked in while the programmer was not looking is intellectually dishonest as it disguises that the error is the programmer's own creation." -- E. W. Dijkstra, EWD1036
At Fri, 5 Sep 2008 10:18:06 +0200,
Quoted 47 lines · Vegard Nossum
Quoted 28 lines · Vegard Nossum
Quoted 27 lines · Vegard Nossum
Quoted 8 lines · Takashi Iwai
At Thu, 4 Sep 2008 17:28:22 -0700,
Quoted 6 lines · Andrew Morton
Quoted 2 lines · On Fri, 05 Sep 2008 01:05:21 +0200 Edgar Kalkowski <[email protected]>…
Dear kernel hackers. ;)
Quoted 8 lines
Quoted 5 lines
Quoted 1 line
[1.] One line summary of the problem: If I unplug my USB-Headset the kernel oopses.
cc's added.
Might be USB, might be ALSA.
Hm, it's hard to guess...
Edgar, could you check whether it happens with 2.6.25?Hi,
I recognize this address:
Quoted 1 line
Quoted 1 line
Quoted 1 line
BUG: unable to handle kernel paging request at 00100100Is this a magic value? I also got it, see for example:
http://lkml.org/lkml/2008/8/21/426Quoted 6 lines
Quoted 4 lines
Google will also recognize it:
http://www.google.com/search?hl=en&q="unable+to+handle+kernel+paging+request"+00100100Where does it come from?
Oh. It _is_
LIST_POISON1. Sorry for the bit of noise.Probably totally unrelated, but I couldn't help to find this bit of code somewhat odd. In
snd_ctl_dev_disconnect():down_read(&card->controls_rwsem); list_for_each_entry(ctl, &card->ctl_files, list) { wake_up(&ctl->change_sleep); kill_fasync(&ctl->fasync, SIGIO, POLL_ERR); } up_read(&card->controls_rwsem);
Quoted 4 lines
...shouldn't that be using
&card->ctl_files_rwlockinstead of&card->controls_rwsem? That one is always used to protect the list ops on&card->ctl_filesin all the other places. Or maybe it is already locked from higher ups?
I think you're right. This should be card->ctl_files_rwlock. Will fix up the code later.
thanks,
Takashi
Sorry that it lasted a while, I had to compile a 2.6.25 kernel. But the error is just the same with it. The funny thing is that it does not happen always but only sometimes (I have to unplug and replug about 5 times until the error occurrs). Looks to me like a threading issue if I may dare to guess. ;)
Regards!
Edgar
Quoted 20 lines · Takashi Iwai
At Thu, 4 Sep 2008 17:28:22 -0700,
Quoted 9 lines · Andrew Morton
Quoted 3 lines · On Fri, 05 Sep 2008 01:05:21 +0200 Edgar Kalkowski <[email protected]>…
Dear kernel hackers. ;)
[1.] One line summary of the problem: If I unplug my USB-Headset the kernel oopses.
cc's added.
Might be USB, might be ALSA.
Hm, it's hard to guess...
Edgar, could you check whether it happens with 2.6.25?thanks,
Takashi