gspca pac7302/pac7311: separate the two subdrivers
PATCH 20/21 gspca pac7302/pac7311: separate the two subdrivers
From: Márton Németh <[email protected]>
All PAC7311 specific functions remain in pac7311.c. All PAC7302 specific functions are moved to pac7302.c. The USB device table is also divided into two parts. This makes it possible to remove the last sensor specific decision in sd_probe() functions.
The common functions are just copied to both subdrivers. These common functions can be separated later to a common file or helper module.
---
drivers/media/video/gspca/Kconfig +9 -0
@@ -103,6 +103,15 @@ config USB_GSPCA_PAC207 To compile this driver as a module, choose M here: the module will be called gspca_pac207. +config USB_GSPCA_PAC7302 + tristate "Pixart PAC7302 USB Camera Driver" + depends on VIDEO_V4L2 && USB_GSPCA + help + Say Y here if you want support for cameras based on the PAC7302 chip. + + To compile this driver as a module, choose M here: the + module will be called gspca_pac7302. + config USB_GSPCA_PAC7311 tristate "Pixart PAC7311 USB Camera Driver" depends on VIDEO_V4L2 && USB_GSPCA
drivers/media/video/gspca/Makefile +2 -0
@@ -8,6 +8,7 @@ obj-$(CONFIG_USB_GSPCA_MR97310A) += gspc obj-$(CONFIG_USB_GSPCA_OV519) += gspca_ov519.o obj-$(CONFIG_USB_GSPCA_OV534) += gspca_ov534.o obj-$(CONFIG_USB_GSPCA_PAC207) += gspca_pac207.o +obj-$(CONFIG_USB_GSPCA_PAC7302) += gspca_pac7302.o obj-$(CONFIG_USB_GSPCA_PAC7311) += gspca_pac7311.o obj-$(CONFIG_USB_GSPCA_SN9C20X) += gspca_sn9c20x.o obj-$(CONFIG_USB_GSPCA_SONIXB) += gspca_sonixb.o
@@ -37,6 +38,7 @@ gspca_mr97310a-objs := mr97310a.o gspca_ov519-objs := ov519.o gspca_ov534-objs := ov534.o gspca_pac207-objs := pac207.o +gspca_pac7302-objs := pac7302.o gspca_pac7311-objs := pac7311.o gspca_sn9c20x-objs := sn9c20x.o gspca_sonixb-objs := sonixb.o
drivers/media/video/gspca/pac7302.c +977 -0
977 lines not on this page · raw message
drivers/media/video/gspca/pac7311.c +3 -712
926 lines not on this page · raw message
From: Márton Németh <[email protected]>
All PAC7311 specific functions remain in pac7311.c. All PAC7302 specific functions are moved to pac7302.c. The USB device table is also divided into two parts. This makes it possible to remove the last sensor specific decision in sd_probe() functions.
The common functions are just copied to both subdrivers. These common functions can be separated later to a common file or helper module.
---
Patch rebased to the latest http://linuxtv.org/hg/v4l-dvb/ (rev 13254).
---
drivers/media/video/gspca/Kconfig +9 -0
@@ -104,6 +104,15 @@ config USB_GSPCA_PAC207 To compile this driver as a module, choose M here: the module will be called gspca_pac207. +config USB_GSPCA_PAC7302 + tristate "Pixart PAC7302 USB Camera Driver" + depends on VIDEO_V4L2 && USB_GSPCA + help + Say Y here if you want support for cameras based on the PAC7302 chip. + + To compile this driver as a module, choose M here: the + module will be called gspca_pac7302. + config USB_GSPCA_PAC7311 tristate "Pixart PAC7311 USB Camera Driver" depends on VIDEO_V4L2 && USB_GSPCA
drivers/media/video/gspca/Makefile +2 -0
@@ -8,6 +8,7 @@ obj-$(CONFIG_USB_GSPCA_MR97310A) += gspc obj-$(CONFIG_USB_GSPCA_OV519) += gspca_ov519.o obj-$(CONFIG_USB_GSPCA_OV534) += gspca_ov534.o obj-$(CONFIG_USB_GSPCA_PAC207) += gspca_pac207.o +obj-$(CONFIG_USB_GSPCA_PAC7302) += gspca_pac7302.o obj-$(CONFIG_USB_GSPCA_PAC7311) += gspca_pac7311.o obj-$(CONFIG_USB_GSPCA_SN9C20X) += gspca_sn9c20x.o obj-$(CONFIG_USB_GSPCA_SONIXB) += gspca_sonixb.o
@@ -38,6 +39,7 @@ gspca_mr97310a-objs := mr97310a.o gspca_ov519-objs := ov519.o gspca_ov534-objs := ov534.o gspca_pac207-objs := pac207.o +gspca_pac7302-objs := pac7302.o gspca_pac7311-objs := pac7311.o gspca_sn9c20x-objs := sn9c20x.o gspca_sonixb-objs := sonixb.o
drivers/media/video/gspca/pac7302.c +978 -0
978 lines not on this page · raw message
drivers/media/video/gspca/pac7311.c +3 -713
927 lines not on this page · raw message