Problem with calibration of AT91SAM9M10EKES
Hi,
I have some calibration problem with my private branch (ulf/linux-2.6.30-2011-01-??) when building the at91sam9m10ekes board.
I am running /usr/bin/run-calibrate.sh,
but regardless of how I click, during calibration,
a tap afterwards always results in detection 3 mm above the tap.
There is a "pointercal" file generated.
It appears to me that this is ignored...
I can tap 1 cm above or below during calibration, and still the detected tap is 3 mm above the actual tap.
I tried this on two boards, with the same problem!
I looked at 89xTs_Calibrate
There is no /etc/init.d/devmand - What does this file do?
Anything else to think about?
I enclose /etc/X11/xorg.conf and /etc/ts.conf.
----------------------------------------------------
xorg.conf:
Section "ServerLayout"
Identifier "default"
InputDevice "atmel-tsadcc" "CorePointer"
EndSection
Section "InputDevice"
Identifier "atmel-tsadcc"
Driver "evdev"
Option "Device" "/dev/input/touchscreen0"
EndSection
Section "InputDevice"
Driver "mouse"
Identifier "Mouse[1]"
Option "Buttons" "10"
Option "Device" "/dev/input/mice"EndSection
Section "InputDevice"
Driver "kbd"
Identifier "Keyboard[0]"
Option "Protocol" "Standard"EndSection
----------------------------------------------------
ts.conf:
# Uncomment if you wish to use the linux input layer event interface module_raw input
# Uncomment if you're using a Sharp Zaurus SL-5500/SL-5000d
# module_raw collie
# Uncomment if you're using a Sharp Zaurus SL-C700/C750/C760/C860
# module_raw corgi
# Uncomment if you're using a device with a UCB1200/1300/1400 TS interface
# module_raw ucb1x00
# Uncomment if you're using an HP iPaq h3600 or similar
# module_raw h3600
# Uncomment if you're using a Hitachi Webpad
# module_raw mk712
# Uncomment if you're using an IBM Arctic II
# module_raw arctic2
module pthres pmin=1
module variance delta=30
module dejitter delta=100
module linear
Signature · 2 lines
Best Regards Ulf Samuelsson
Dnia środa, 26 stycznia 2011 o 10:40:25 Ulf Samuelsson napisał(a):
Quoted 7 lines
I have some calibration problem with my private branch (ulf/linux-2.6.30-2011-01-??) when building the at91sam9m10ekes board.
I am running
/usr/bin/run-calibrate.sh,
but regardless of how I click, during calibration,
a tap afterwards always results in detection 3 mm above the tap.
Quoted 7 lines
There is a "pointercal" file generated.
It appears to me that this is ignored...
I can tap 1 cm above or below during calibration, and still the detected tap is 3 mm above the actual tap.Anything else to think about?
I enclose/etc/X11/xorg.confand/etc/ts.conf.
You are using full X11 with evdev driver so tslib is not used at all. You have to use xinput-calibrator.
Regards,
Signature · 3 lines
JID: [email protected] Website: http://marcin.juszkiewicz.com.pl/ LinkedIn: http://www.linkedin.com/in/marcinjuszkiewicz
2011-01-26 14:01, Marcin Juszkiewicz skrev:
Quoted 13 lines
Dnia środa, 26 stycznia 2011 o 10:40:25 Ulf Samuelsson napisał(a):
Quoted 11 lines
I have some calibration problem with my private branch (ulf/linux-2.6.30-2011-01-??) when building the at91sam9m10ekes board.
I am running
/usr/bin/run-calibrate.sh,
but regardless of how I click, during calibration,
a tap afterwards always results in detection 3 mm above the tap.There is a "pointercal" file generated.
It appears to me that this is ignored...
I can tap 1 cm above or below during calibration, and still the detected tap is 3 mm above the actual tap.
Quoted 6 lines
Quoted 2 lines
Anything else to think about?
I enclose/etc/X11/xorg.confand/etc/ts.conf.You are using full X11 with evdev driver so tslib is not used at all. You have to use xinput-calibrator.
Regards,
Hmm, I thought I was using xserver-kdrive!
(Have PREFERRED_PROVIDER_xserver = "xserver-kdrive" in the machine conf file)
Looking closer at the image (x11-at91sam9-image), it contains
XSERVER = "xserver-xorg \
xf86-input-evdev \
xf86-input-tslib \
xf86-video-fbdev "so the xserver-kdrive is overridden.
This was copied from "xorg-image.bb" which I guess then have the same problem using full x-server and tslib.
"qt4-x11-base-image.bb" has this combination as well.
"xserver-common_1.33.bb" is built and contains:
+++++++++++++++++++++++++
RDEPENDS_${PN}_append_angstrom = " tslib-calibrate " RDEPENDS_${PN}_append_shr = " xinput-calibrator "
-----------------------------------------------------
and I am building "angstrom" I do not get "xinput-calibrator"
I added xinput-calibrate to the x11-at91sam9-image, but after the build, Removed "xf86-input-tslib", but the dependence on "tslib-calibrate" remains in "xserver-common_1.33.bb"
Maybe this needs to change as well.
I get the same startup calibration program ("run-calibrate.sh" calling ts_calibrate). with the same poor result.
There are no scripts calling "xinput-calibrator".
Shouldn't that happen at startup?
Can call it manually, and then suddenly I am much better off. Still it not perfect though.
Any clue to get xinput-calibrate to run at first boot?
Best Regards
Ulf Samuelsson
Quoted 14 lines · Ulf Samuelsson
2011-01-26 14:01, Marcin Juszkiewicz skrev:
Quoted 13 lines
Dnia środa, 26 stycznia 2011 o 10:40:25 Ulf Samuelsson napisał(a):
Quoted 11 lines
I have some calibration problem with my private branch (ulf/linux-2.6.30-2011-01-??) when building the at91sam9m10ekes board.
I am running
/usr/bin/run-calibrate.sh,
but regardless of how I click, during calibration,
a tap afterwards always results in detection 3 mm above the tap.There is a "pointercal" file generated.
It appears to me that this is ignored...
I can tap 1 cm above or below during calibration, and still the detected tap is 3 mm above the actual tap.
Quoted 8 lines
Quoted 6 lines
Quoted 2 lines
Anything else to think about?
I enclose/etc/X11/xorg.confand/etc/ts.conf.You are using full X11 with evdev driver so tslib is not used at all. You have to use xinput-calibrator.
Regards,
Any clue to get xinput-calibrate to run at first boot?
provide
recipes/xinput-calibrator/pointercal-xinput
data for your device and use recipes/xserver-common/files/89xTs_Calibrate.xinput_calibrator.patch like SHR does
intentionaly it prefers provideded data, because users too often messed initial calibration on first boot and then didn't know how to reset it and rerun xinpu-calibration successfully...
Signature · 1 line
Martin 'JaMa' Jansa jabber: [email protected]
2011-01-26 21:06, Martin Jansa skrev:
Quoted 19 lines · Ulf Samuelsson
Quoted 18 lines
2011-01-26 14:01, Marcin Juszkiewicz skrev:
Quoted 17 lines
Dnia s'roda, 26 stycznia 2011 o 10:40:25 Ulf Samuelsson napisa?(a):
Quoted 7 lines
I have some calibration problem with my private branch (ulf/linux-2.6.30-2011-01-??) when building the at91sam9m10ekes board.
I am running
/usr/bin/run-calibrate.sh,
but regardless of how I click, during calibration,
a tap afterwards always results in detection 3 mm above the tap.Quoted 6 lines
There is a "pointercal" file generated.
It appears to me that this is ignored...
I can tap 1 cm above or below during calibration, and still the detected tap is 3 mm above the actual tap. Anything else to think about?
I enclose/etc/X11/xorg.confand/etc/ts.conf.You are using full X11 with evdev driver so tslib is not used at all. You have to use xinput-calibrator.
Quoted 7 lines
Quoted 2 lines
Quoted 1 line
Regards,
Any clue to get xinput-calibrate to run at first boot?
provide
recipes/xinput-calibrator/pointercal-xinput
data for your device and userecipes/xserver-common/files/89xTs_Calibrate.xinput_calibrator.patchlike SHR does
OK, then is the question how:
As I noted:SRC_URI_append_angstrom = " file://xtscal-fix.patch " RDEPENDS_${PN}_append_angstrom = " tslib-calibrate " RDEPENDS_${PN}_append_shr = " xinput-calibrator "?
so Angstrom (which I am using) is using "tslib-calibrate" Is there any drawback in changing this to " xinput-calibrator "
Adding a SRC_URI_append_at91 seems a kludge.
Quoted 10 lines
intentionaly it prefers provideded data, because users too often messed initial calibration on first boot and then didn't know how to reset it and rerun xinpu-calibration successfully...
_______________________________________________
Openembedded-devel mailing list
[email protected]
http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel
Signature · 2 lines
Best Regards Ulf Samuelsson