Skip to contentSkip to conversation

AMD Bulldozer FX-8150 Powers off during kernel build

DISCUSSION Sid Boyce 2 participants 4 messages Sep 13, 2012

lore
Share & tools
lore

Sid Boyce

author
#0 lore raw

I have a huge heatsink and large CPU fan plus lots of cooling fans in the case and nothing gets hot. If I build e.g 3.6-rc5 with 8 or 6 cores, part way through it suddenly powers off.

I have checked hwmon/k10temp.c to see if I could see where these values were defined.

k10temp.h is 0 bytes.
-rw-r--r-- 1 root root 0 Sep 9 01:59 /usr/src/linux-3.6.0-rc5/include/config/sensors/k10temp.h

Currently I build with "make -j 1" and temperature and power values are around those below.

# sensors
k10temp-pci-00c3
Adapter: PCI adapter
temp1:        +60.4°C  (high = +70.0°C)
                       (crit = +90.0°C, hyst = +87.0°C)

fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 127.49 W (crit = 124.77 W)

# cat /proc/cpuinfo
processor       : 0
vendor_id       : AuthenticAMD
cpu family      : 21
model           : 1
model name      : AMD FX(tm)-8150 Eight-Core Processor
stepping        : 2
microcode       : 0x6000626
cpu MHz         : 3600.000
cache size      : 2048 KB

from .config:-

# grep HWMON .config
CONFIG_IXGBE_HWMON=y
CONFIG_HWMON=y
CONFIG_HWMON_VID=m
# CONFIG_HWMON_DEBUG_CHIP is not set
CONFIG_THERMAL_HWMON=y
# grep POWERSAVE .config
# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
# CONFIG_PCIEASPM_POWERSAVE is not set
CONFIG_DEVFREQ_GOV_POWERSAVE=y

On another 6-core box I can build kernels with "make -j 6" without problems.

# cat /proc/cpuinfo
processor       : 0
vendor_id       : AuthenticAMD
cpu family      : 21
model           : 1
model name      : AMD FX(tm)-6100 Six-Core Processor
stepping        : 2
microcode       : 0x6000623
cpu MHz         : 3300.000
cache size      : 2048 KB

With a kernel build going on six core box, temperature and power hover around the values below. sabre:~ # sensors
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +50.2°C (high = +70.0°C)

                       (crit = +90.0°C, hyst = +87.0°C)

fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 94.40 W (crit = 95.01 W)

73 ... Sid.

Signature · 4 lines
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Senior Staff Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
#1 lore raw
Quoted 4 lines · Sid Boyce

I have a huge heatsink and large CPU fan plus lots of cooling fans in the case and nothing gets hot.
If I build e.g 3.6-rc5 with 8 or 6 cores, part way through it suddenly powers off.

Ok, can you catch the whole dmesg when you boot the machine _after_ the sudden poweroff? You can send it to me and Andreas (on CC) privately if you prefer.

Important: make sure the kernel has CONFIG_X86_MCE and CONFIG_EDAC_DECODE_MCE built-in.

Please make sure to use a recent kernel, i.e. 3.4, 3.5 is fine.

Thanks.

(Leaving in the rest for reference)

Quoted 81 lines

I have checked hwmon/k10temp.c to see if I could see where these values were defined.

k10temp.h is 0 bytes.
-rw-r--r-- 1 root root 0 Sep 9 01:59 /usr/src/linux-3.6.0-rc5/include/config/sensors/k10temp.h

Currently I build with "make -j 1" and temperature and power values are around those below.

# sensors
k10temp-pci-00c3
Adapter: PCI adapter
temp1:        +60.4°C  (high = +70.0°C)
                       (crit = +90.0°C, hyst = +87.0°C)

fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 127.49 W (crit = 124.77 W)

# cat /proc/cpuinfo
processor       : 0
vendor_id       : AuthenticAMD
cpu family      : 21
model           : 1
model name      : AMD FX(tm)-8150 Eight-Core Processor
stepping        : 2
microcode       : 0x6000626
cpu MHz         : 3600.000
cache size      : 2048 KB

from .config:-

# grep HWMON .config
CONFIG_IXGBE_HWMON=y
CONFIG_HWMON=y
CONFIG_HWMON_VID=m
# CONFIG_HWMON_DEBUG_CHIP is not set
CONFIG_THERMAL_HWMON=y
# grep POWERSAVE .config
# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
# CONFIG_PCIEASPM_POWERSAVE is not set
CONFIG_DEVFREQ_GOV_POWERSAVE=y

On another 6-core box I can build kernels with "make -j 6" without problems.

# cat /proc/cpuinfo
processor       : 0
vendor_id       : AuthenticAMD
cpu family      : 21
model           : 1
model name      : AMD FX(tm)-6100 Six-Core Processor
stepping        : 2
microcode       : 0x6000623
cpu MHz         : 3300.000
cache size      : 2048 KB

With a kernel build going on six core box, temperature and power hover around the values below.
sabre:~ # sensors
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +50.2°C (high = +70.0°C)

                       (crit = +90.0°C, hyst = +87.0°C)

fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 94.40 W (crit = 95.01 W)

73 ... Sid.

Signature · 10 lines
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Senior Staff Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/
Signature · 2 lines
Regards/Gruss,
    Boris.
author
#2 lore raw
# uname -r
3.6.0-rc5-u1-smp+

I built a new 3.6-rc5 kernel (3.6.0-rc5-u2) using 3.6.0-rc5-u1 with 8 cores and power off didn't ocur. slipstream:/usr/src/linux-3.6.0-rc5-u1 # grep POWER .config
# CONFIG_ACPI_PROCFS_POWER is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_X86_POWERNOW_K8=m
# CONFIG_PCIEASPM_POWERSAVE is not set
CONFIG_INPUT_POWERMATE=m
CONFIG_IPMI_POWEROFF=m
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
CONFIG_PDA_POWER=m
CONFIG_TEST_POWER=m
CONFIG_POWER_AVS=y
CONFIG_SENSORS_FAM15H_POWER=m
CONFIG_SENSORS_ACPI_POWER=m
CONFIG_SND_AC97_POWER_SAVE=y
CONFIG_SND_AC97_POWER_SAVE_DEFAULT=0
# CONFIG_SND_HDA_POWER_SAVE is not set
# CONFIG_HID_LCPOWER is not set
CONFIG_DEVFREQ_GOV_POWERSAVE=y
CONFIG_EVENT_POWER_TRACING_DEPRECATED=y
# CONFIG_XZ_DEC_POWERPC is not set

When it was powering off "CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y" was set. slipstream:/usr/src/linux-3.6.0-rc5-u1 # grep PERFORMANCE .config # CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_PCIEASPM_PERFORMANCE=y
CONFIG_DEVFREQ_GOV_PERFORMANCE=y

slipstream:/usr/src/linux-3.6.0-rc5-u1 # grep MCE .config CONFIG_X86_MCE=y
# CONFIG_X86_MCE_INTEL is not set CONFIG_X86_MCE_AMD=y
CONFIG_X86_MCE_THRESHOLD=y
# CONFIG_X86_MCE_INJECT is not set CONFIG_EDAC_DECODE_MCE=y
# CONFIG_EDAC_MCE_INJ is not set

During the build temperature and power was around these values
-------------------------------------------------------------------------------------
fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 133.30 W (crit = 124.77 W)

k10temp-pci-00c3
Adapter: PCI adapter
temp1: +61.9°C (high = +70.0°C)

                       (crit = +90.0°C, hyst = +87.0°C)

Immediately after the build the values are much lower than what it was with the kernel and config that caused the power off.
----------------------------------------
fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 31.10 W (crit = 124.77 W)

k10temp-pci-00c3
Adapter: PCI adapter
temp1: +33.2°C (high = +70.0°C)

                       (crit = +90.0°C, hyst = +87.0°C)

------------------------------------------

If needed I can go back to the earlier 3.6.0-rc5 kernel and config to recreate the power off situation. With the kernel that powered off, MCE was not set and CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y

For the 3.6.0-rc5-u1 kernel only those 2 were changed. Regards
Sid.

Quoted 90 lines · Borislav Petkov
Quoted 4 lines · Sid Boyce

I have a huge heatsink and large CPU fan plus lots of cooling fans in the case and nothing gets hot.
If I build e.g 3.6-rc5 with 8 or 6 cores, part way through it suddenly powers off.

Ok, can you catch the whole dmesg when you boot the machine _after_ the sudden poweroff? You can send it to me and Andreas (on CC) privately if you prefer.

Important: make sure the kernel has CONFIG_X86_MCE and CONFIG_EDAC_DECODE_MCE built-in.

Please make sure to use a recent kernel, i.e. 3.4, 3.5 is fine.

Thanks.

(Leaving in the rest for reference)

Quoted 72 lines

I have checked hwmon/k10temp.c to see if I could see where these values were defined.

k10temp.h is 0 bytes.
-rw-r--r-- 1 root root 0 Sep 9 01:59 /usr/src/linux-3.6.0-rc5/include/config/sensors/k10temp.h

Currently I build with "make -j 1" and temperature and power values are around those below.

# sensors
k10temp-pci-00c3
Adapter: PCI adapter
temp1:        +60.4°C  (high = +70.0°C)
                        (crit = +90.0°C, hyst = +87.0°C)

fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 127.49 W (crit = 124.77 W)

# cat /proc/cpuinfo
processor       : 0
vendor_id       : AuthenticAMD
cpu family      : 21
model           : 1
model name      : AMD FX(tm)-8150 Eight-Core Processor
stepping        : 2
microcode       : 0x6000626
cpu MHz         : 3600.000
cache size      : 2048 KB

from .config:-

# grep HWMON .config
CONFIG_IXGBE_HWMON=y
CONFIG_HWMON=y
CONFIG_HWMON_VID=m
# CONFIG_HWMON_DEBUG_CHIP is not set
CONFIG_THERMAL_HWMON=y
# grep POWERSAVE .config
# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
# CONFIG_PCIEASPM_POWERSAVE is not set
CONFIG_DEVFREQ_GOV_POWERSAVE=y

On another 6-core box I can build kernels with "make -j 6" without problems.

# cat /proc/cpuinfo
processor       : 0
vendor_id       : AuthenticAMD
cpu family      : 21
model           : 1
model name      : AMD FX(tm)-6100 Six-Core Processor
stepping        : 2
microcode       : 0x6000623
cpu MHz         : 3300.000
cache size      : 2048 KB

With a kernel build going on six core box, temperature and power hover around the values below.
sabre:~ # sensors
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +50.2°C (high = +70.0°C)

                        (crit = +90.0°C, hyst = +87.0°C)

fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 94.40 W (crit = 95.01 W)

73 ... Sid.

Signature · 4 lines
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Senior Staff Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
#3 lore raw
Quoted 3 lines · Sid Boyce

If needed I can go back to the earlier 3.6.0-rc5 kernel and config to recreate the power off situation. With the kernel that powered off, MCE was not set and CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y

Yes, as I suggested earlier, enable CONFIG_X86_MCE and CONFIG_EDAC_DECODE_MCE and *then* try recreating the reboot.

After it reboots, catch the whole dmesg and send it to me.

Thanks.

Signature · 2 lines
Regards/Gruss,
    Boris.