Skip to contentSkip to conversation

Slow large pings

LARTC kasp 2 participants 2 messages Jan 9, 2005 – Jan 13, 2005

lore
Share & tools
lore

kasp

author
#0 lore raw

Hello lartc,

Testing some rules I found out that any rules are slowing down large pings! For example:

tc qdisc add dev eth0 root handle 1: htb
tc class add dev eth0 parent 1: classid 1:1 htb rate 100Mbit prio 1 ceil 100Mbit tc class add dev eth0 parent 1:1 classid 1:2 htb rate 100Mbit prio 2 ceil 100Mbit

tc filter add dev eth0 parent 1:0 prio 5 u32 \
    match ip src 10.10.10.1 \
    match ip dst 10.10.10.10 \
    flowid 1:2

tc qdisc add dev eth0 parent 1:2 handle 2: sfq perturb 10

Small pings are ok - <10ms, here is output for 65500 byte pings:

Pinging test [10.10.10.1] with 65500 bytes of data:

Reply from 10.10.10.1: bytese500 time0ms TTLd
Reply from 10.10.10.1: bytese500 time0ms TTLd
Reply from 10.10.10.1: bytese500 time0ms TTLd
Reply from 10.10.10.1: bytese500 time0ms TTLd

Ping statistics for 10.10.10.1:

    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 120ms, Maximum =  120ms, Average =  120ms

If I don't use any rules, 65500 byte pings are about ~10ms Any filters are slowing large pings for 10 times!!! What can I do to tune it up?

Signature · 6 lines
Best regards,
 kasp                          mailto:[email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw
Quoted 3 lines · kasp

Hello lartc,

Testing some rules I found out that any rules are slowing down large pings!

I can't reproduce this.

Quoted 7 lines

For example:

tc qdisc add dev eth0 root handle 1: htb
tc class add dev eth0 parent 1: classid 1:1 htb rate 100Mbit prio 1 ceil 100Mbit tc class add dev eth0 parent 1:1 classid 1:2 htb rate 100Mbit prio 2 ceil 100Mbit

tc filter add dev eth0 parent 1:0 prio 5 u32 \

Error for me unless I add protocol ip

Quoted 6 lines
    match ip src 10.10.10.1 \
    match ip dst 10.10.10.10 \
    flowid 1:2

tc qdisc add dev eth0 parent 1:2 handle 2: sfq perturb 10

Small pings are ok - <10ms, here is output for 65500 byte pings:

10ms is high I get 0.3 with p200mmx +rtl8139 + cheapest switch I could find + cables made without crimping tool.

Quoted 8 lines

Pinging test [10.10.10.1] with 65500 bytes of data:

Reply from 10.10.10.1: bytese500 time0ms TTLd
Reply from 10.10.10.1: bytese500 time0ms TTLd
Reply from 10.10.10.1: bytese500 time0ms TTLd
Reply from 10.10.10.1: bytese500 time0ms TTLd

I see 14ms

Quoted 9 lines

Ping statistics for 10.10.10.1:

    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 120ms, Maximum =  120ms, Average =  120ms

If I don't use any rules, 65500 byte pings are about ~10ms Any filters are slowing large pings for 10 times!!! What can I do to tune it up?

What kernel and hardware are you using?

Andy.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/