Skip to contentSkip to conversation

rate limiting netmask w/ dd-wrt

LARTC Ryan O'Toole 2 participants 2 messages May 26, 2007 – May 30, 2007

lore
Share & tools
lore
#0 lore raw

I'm trying to setup a DD-WRT router (www.dd-wrt.com; embedded micro-device linux for the uninitiated) to rate limit all the traffic it receives from its wi-fi interface. I followed the instructions from the cookbook section on rate limiting (http://lartc.org/howto/lartc.ratelimit.single.html), but it doesn't appear to be working. I tested by checking my laptop's bandwidth on http://www.speakeasy.net/speedtest/. Here's the commands I issued to tc:

# tc qdisc add dev $DEV root handle 1: cbq avpkt 1000 bandwidth 10mbit
# tc class add dev $DEV parent 1: classid 1:1 cbq rate 512kbit allot 1500
prio 5 bounded isolated
# tc filter add dev $DEV parent 1: protocol ip prio 16 u32 match ip src
192.168.1.0/24 flowid 1:1

I replaced $DEV with each interface name in succession, as I wasn't sure which to use. Here's the output of ifconfig from the router:

# ifconfig
br0       Link encap:Ethernet  HWaddr 00:16:01:59:EF:00
         inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:114200 errors:0 dropped:0 overruns:0 frame:0
         TX packets:125307 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:14568079 (13.8 MiB)  TX bytes:71752923 (68.4 MiB)

eth0 Link encap:Ethernet HWaddr 00:16:01:59:EF:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:64266 errors:0 dropped:0 overruns:0 frame:0 TX packets:54720 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:65677538 (62.6 MiB) TX bytes:12736990 (12.1 MiB) Interrupt:4

eth1 Link encap:Ethernet HWaddr 00:16:01:59:EF:02

         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:117891 errors:0 dropped:0 overruns:0 frame:253671
         TX packets:133961 errors:3 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:16589572 (15.8 MiB)  TX bytes:75539860 (72.0 MiB)
         Interrupt:2 Base address:0x5000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1 RX packets:46 errors:0 dropped:0 overruns:0 frame:0 TX packets:46 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0
RX bytes:5328 (5.2 KiB) TX bytes:5328 (5.2 KiB)

vlan0 Link encap:Ethernet HWaddr 00:16:01:59:EF:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:5570 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:1086810 (1.0 MiB)

vlan1 Link encap:Ethernet HWaddr 00:16:01:59:EF:01

         inet addr:192.168.10.138  Bcast:192.168.10.255  Mask:255.255.255.0
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:64281 errors:0 dropped:0 overruns:0 frame:0
         TX packets:49178 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:64522436 (61.5 MiB)  TX bytes:11432967 (10.9 MiB)

Can anyone tell me what I'm doing wrong here?

Best,
Ryan

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#1 lore raw
Quoted 3 lines · Ryan O'Toole

I'm trying to setup a DD-WRT router (www.dd-wrt.com; embedded micro-device linux for the uninitiated) to rate limit all the traffic it receives from its wi-fi interface.

Qdiscs work on traffic leaving the interfaces. If you want to limit incoming traffic have a look at the policer example in LARTC, there are other ways using ifb/imq, but I don't know if dd-wrt will have those.

Wireless is a special case - half duplex, so it's going to be even harder to do.

Andy.

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc