Skip to contentSkip to conversation

Small fixex for xserver-nodm-init-systemd

PATCH In review Martin Jansa 2 participants 8 messages Apr 10, 2012 – Apr 12, 2012

lore
Share & tools
lore
#0 lore raw

cover Small fixex for xserver-nodm-init-systemd

The following changes since commit 9fb576a0d53d4bd511eee64f44d4ed187acdd83c:

gcc-4.6: Update to 2012.03 linaro release (2012-04-08 07:48:16 +0200)

are available in the git repository at:
git://git.openembedded.org/meta-openembedded-contrib jansa/xorg
http://cgit.openembedded.org/cgit.cgi/meta-openembedded-contrib/log/?h=jansa/xorg

Denis 'GNUtoo' Carikli (1):
xserver-nodm-init: use /etc/X11/Xserver from service file instead of
Xorg directly

Martin Jansa (1):
xserver-nodm-init: add EnvironmentFile

 .../xserver-nodm-init-2.0/xserver-nodm.conf        |    1 +
 .../xserver-nodm-init-2.0/xserver-nodm.service     |    3 ++-
 .../xserver-nodm-init/xserver-nodm-init_2.0.bb     |    7 ++++++-
 3 files changed, 9 insertions(+), 2 deletions(-)
 create mode 100644 meta-oe/recipes-graphics/xserver-nodm-init/xserver-nodm-init-2.0/xserver-nodm.conf
Signature · 1 line
1.7.8.5
#1 lore raw

PATCH 1/2 xserver-nodm-init: use /etc/X11/Xserver from service file instead of Xorg directly

From: Denis 'GNUtoo' Carikli <[email protected]>

* /etc/X11/Xserver is provided by xserver-common and sets correct DPI before starting Xorg (or other xserver)

---
 .../xserver-nodm-init-2.0/xserver-nodm.service     |    2 +-
 .../xserver-nodm-init/xserver-nodm-init_2.0.bb     |    2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
meta-oe/recipes-graphics/xserver-nodm-init/xserver-nodm-init-2.0/xserver-nodm.service +1 -1
index b781c7d..a35d70e 100644
@@ -2,7 +2,7 @@
 Description=Xserver startup with a display manager
 
 [Service]
-ExecStart=/usr/bin/xinit /etc/X11/Xsession -- /usr/bin/Xorg
+ExecStart=/usr/bin/xinit /etc/X11/Xsession -- /etc/X11/Xserver
 
 [Install]
 WantedBy=multi-user.target
meta-oe/recipes-graphics/xserver-nodm-init/xserver-nodm-init_2.0.bb +1 -1
index 98025d3..36d9bfc 100644
@@ -3,7 +3,7 @@ LICENSE = "GPLv2"
 LIC_FILES_CHKSUM = "file://COPYING;md5=751419260aa954499f7abaabaa882bbe"
 SECTION = "x11"
 
-PR = "r13"
+PR = "r14"
 
 SRC_URI = "file://xserver-nodm \
            file://xserver-nodm.service \
Signature · 1 line
1.7.8.5
#2 lore raw

PATCH 2/2 xserver-nodm-init: add EnvironmentFile

* used to set HOME variable before /etc/X11/Xsession is started
* e.g. enlightenment is creating ${HOME}/.e and without this it ends in /tmp/.e and during startup HOME gets defined and switched to /home/root/.e

---
 .../xserver-nodm-init-2.0/xserver-nodm.conf        |    1 +
 .../xserver-nodm-init-2.0/xserver-nodm.service     |    1 +
 .../xserver-nodm-init/xserver-nodm-init_2.0.bb     |    7 ++++++-
 3 files changed, 8 insertions(+), 1 deletions(-)
 create mode 100644 meta-oe/recipes-graphics/xserver-nodm-init/xserver-nodm-init-2.0/xserver-nodm.conf
meta-oe/recipes-graphics/xserver-nodm-init/xserver-nodm-init-2.0/xserver-nodm.conf new file +1 -0
new file mode 100644
index 0000000..3c0582a
@@ -0,0 +1 @@
+HOME=/home/root
meta-oe/recipes-graphics/xserver-nodm-init/xserver-nodm-init-2.0/xserver-nodm.service +1 -0
index a35d70e..c15a772 100644
@@ -2,6 +2,7 @@
 Description=Xserver startup with a display manager
 
 [Service]
+EnvironmentFile=/etc/default/xserver-nodm
 ExecStart=/usr/bin/xinit /etc/X11/Xsession -- /etc/X11/Xserver
 
 [Install]
meta-oe/recipes-graphics/xserver-nodm-init/xserver-nodm-init_2.0.bb +6 -1
index 36d9bfc..62c33c9 100644
@@ -3,10 +3,11 @@ LICENSE = "GPLv2"
 LIC_FILES_CHKSUM = "file://COPYING;md5=751419260aa954499f7abaabaa882bbe"
 SECTION = "x11"
 
-PR = "r14"
+PR = "r16"
 
 SRC_URI = "file://xserver-nodm \
            file://xserver-nodm.service \
+           file://xserver-nodm.conf \
            file://gplv2-license.patch \
 "
 S = "${WORKDIR}"
@@ -25,7 +26,11 @@ SYSTEMD_SERVICE_${PN}-systemd = "xserver-nodm.service"
 do_install() {
 	install -d ${D}${sysconfdir}/init.d
 	install xserver-nodm ${D}${sysconfdir}/init.d
+	install -d ${D}${sysconfdir}/default
+	install xserver-nodm.conf ${D}${sysconfdir}/default/xserver-nodm
 }
 
+FILES_${PN}-systemd += "${sysconfdir}/default/xserver-nodm"
+
 RDEPENDS_${PN} = "xserver-common (>= 1.30) xinit"
 RDEPENDS_${PN}-systemd += "xserver-common (>= 1.30) xinit"
Signature · 1 line
1.7.8.5
Acked-by on v1 2/2
#3 lore raw

Re: [meta-oe][PATCH 2/2] xserver-nodm-init: add EnvironmentFile

Quoted 6 lines · Martin Jansa

* used to set HOME variable before /etc/X11/Xsession is started
* e.g. enlightenment is creating ${HOME}/.e and without this it ends in /tmp/.e and during startup HOME gets defined and switched to /home/root/.e

Agreed :-)

Signature · 3 lines
Otavio Salvador                             O.S. Systems
E-mail: [email protected]  http://www.ossystems.com.br
Mobile: +55 53 9981-7854              http://projetos.ossystems.com.br
#4 lore raw

Re: [meta-oe][PATCH 1/2] xserver-nodm-init: use /etc/X11/Xserver from service file instead of Xorg directly

In reply to Martin Jansa
Quoted 2 lines · Martin Jansa

* /etc/X11/Xserver is provided by xserver-common and sets correct DPI before starting Xorg (or other xserver)

This breaks the images using systemd only as it depends on init.d/functions now.

Signature · 3 lines
Otavio Salvador                             O.S. Systems
E-mail: [email protected]  http://www.ossystems.com.br
Mobile: +55 53 9981-7854              http://projetos.ossystems.com.br
#5 lore raw

Re: [meta-oe][PATCH 1/2] xserver-nodm-init: use /etc/X11/Xserver from service file instead of Xorg directly

Quoted 5 lines · Otavio Salvador
Quoted 2 lines · Martin Jansa

* /etc/X11/Xserver is provided by xserver-common and sets correct DPI before starting Xorg (or other xserver)

This breaks the images using systemd only as it depends on init.d/functions now.

Ah sorry I still had initscripts around in systemd image, please test following patch. I'm sending all those changes also to florian to apply them upstream so maybe we'll drop them from meta-oe and use 1.35 instead later.

Cheers,

Quoted 10 lines
Signature · 9 lines
-- 
Otavio Salvador                             O.S. Systems
E-mail: [email protected]  http://www.ossystems.com.br
Mobile: +55 53 9981-7854              http://projetos.ossystems.com.br

_______________________________________________
Openembedded-devel mailing list
[email protected]
http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel
Signature · 1 line
Martin 'JaMa' Jansa     jabber: [email protected]
#6 lore raw

PATCH 1/1 xserver-common: use git patches and add functions file

* otherwise we were depending on initscripts to provide it without RDEPENDing on it

---
 .../0001-COPYING-add-GPLv2-license-file.patch      |  364 ++++++++++++++++++++
 .../0002-add-setdpi-Xinit.d-script.patch           |  112 ++++++
 ...0003-add-89xdgautostart-Xsession.d-script.patch |   29 ++
 ...brate_xinput_calibrator-Xsession.d-script.patch |   27 ++
 ...0005-add-XWindowManager-Xsession.d-script.patch |   26 ++
 ...06-add-support-for-etc-X11-xserver-system.patch |   26 ++
 ...nctions-file-instead-etc-init.d-functions.patch |   87 +++++
 ...mon-add-dpi-and-nocursor-params-for-gta01.patch |   40 +++
 ...mon-add-support-for-n900-alias-nokia_rx-5.patch |   32 ++
 ...mon-add-support-for-nexus-S-alias-herring.patch |   27 ++
 ...mon-add-support-for-nexus-one-alias-mahim.patch |   28 ++
 ...mon-add-support-for-gta04-alias-OpenPhoen.patch |   33 ++
 .../89xTs_Calibrate.xinput_calibrator.patch        |   12 -
 .../xserver-common-1.34/89xdgautostart.sh          |    9 -
 .../xserver-common-1.34/90xXWindowManager.patch    |   11 -
 .../Xserver.add.dpi.for.gta.patch                  |   29 --
 .../Xserver.add.nocursor.for.gta.patch             |   20 -
 .../Xserver.add.xserver-system.patch               |   12 -
 .../xserver-common-1.34/Xserver.gta04.patch        |   32 --
 .../xserver-common-1.34/Xserver.n900.patch         |   17 -
 .../xserver-common-1.34/Xserver.nexusone.patch     |   14 -
 .../xserver-common-1.34/Xserver.nexuss.patch       |   14 -
 .../xserver-common-1.34/gplv2-license.patch        |  353 -------------------
 .../xserver-common/xserver-common-1.34/setDPI.sh   |   92 -----
 .../xserver-common/xserver-common_1.34.bb          |   29 +-
 25 files changed, 844 insertions(+), 631 deletions(-)
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0001-COPYING-add-GPLv2-license-file.patch
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0002-add-setdpi-Xinit.d-script.patch
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0003-add-89xdgautostart-Xsession.d-script.patch
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0004-add-Ts_Calibrate_xinput_calibrator-Xsession.d-script.patch
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0005-add-XWindowManager-Xsession.d-script.patch
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0006-add-support-for-etc-X11-xserver-system.patch
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0007-use-own-functions-file-instead-etc-init.d-functions.patch
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0008-xserver-common-add-dpi-and-nocursor-params-for-gta01.patch
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0009-xserver-common-add-support-for-n900-alias-nokia_rx-5.patch
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0010-xserver-common-add-support-for-nexus-S-alias-herring.patch
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0011-xserver-common-add-support-for-nexus-one-alias-mahim.patch
 create mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0012-xserver-common-add-support-for-gta04-alias-OpenPhoen.patch
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/89xTs_Calibrate.xinput_calibrator.patch
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/89xdgautostart.sh
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/90xXWindowManager.patch
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.add.dpi.for.gta.patch
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.add.nocursor.for.gta.patch
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.add.xserver-system.patch
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.gta04.patch
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.n900.patch
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.nexusone.patch
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.nexuss.patch
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/gplv2-license.patch
 delete mode 100644 meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/setDPI.sh
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0001-COPYING-add-GPLv2-license-file.patch new file +364 -0
new file mode 100644
index 0000000..29dd71a
@@ -0,0 +1,364 @@
+From 834fa06920f88ceedf752964c8e296c653d541e4 Mon Sep 17 00:00:00 2001
+From: Yu Ke <[email protected]>
+Date: Wed, 11 Apr 2012 14:26:16 +0200
+Subject: [PATCH 01/12] COPYING: add GPLv2 license file
+
+this is a local file recipe and the license file is missing.In order
+to pass the license checksum checking, the license file is needed. So
+this patch add the GPLv2 license file.
+
+Signed-off-by: Yu Ke <[email protected]>
+Signed-off-by: Martin Jansa <[email protected]>
+---
+ COPYING |  339 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ 1 files changed, 339 insertions(+), 0 deletions(-)
+ create mode 100644 COPYING
+
+diff --git a/COPYING b/COPYING
+new file mode 100644
+index 0000000..d511905
+--- /dev/null
++++ b/COPYING
+@@ -0,0 +1,339 @@
++		    GNU GENERAL PUBLIC LICENSE
++		       Version 2, June 1991
++
++ Copyright (C) 1989, 1991 Free Software Foundation, Inc.,
++ 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
++ Everyone is permitted to copy and distribute verbatim copies
++ of this license document, but changing it is not allowed.
++
++			    Preamble
++
++  The licenses for most software are designed to take away your
++freedom to share and change it.  By contrast, the GNU General Public
++License is intended to guarantee your freedom to share and change free
++software--to make sure the software is free for all its users.  This
++General Public License applies to most of the Free Software
++Foundation's software and to any other program whose authors commit to
++using it.  (Some other Free Software Foundation software is covered by
++the GNU Lesser General Public License instead.)  You can apply it to
++your programs, too.
++
++  When we speak of free software, we are referring to freedom, not
++price.  Our General Public Licenses are designed to make sure that you
++have the freedom to distribute copies of free software (and charge for
++this service if you wish), that you receive source code or can get it
++if you want it, that you can change the software or use pieces of it
++in new free programs; and that you know you can do these things.
++
++  To protect your rights, we need to make restrictions that forbid
++anyone to deny you these rights or to ask you to surrender the rights.
++These restrictions translate to certain responsibilities for you if you
++distribute copies of the software, or if you modify it.
++
++  For example, if you distribute copies of such a program, whether
++gratis or for a fee, you must give the recipients all the rights that
++you have.  You must make sure that they, too, receive or can get the
++source code.  And you must show them these terms so they know their
++rights.
++
++  We protect your rights with two steps: (1) copyright the software, and
++(2) offer you this license which gives you legal permission to copy,
++distribute and/or modify the software.
++
++  Also, for each author's protection and ours, we want to make certain
++that everyone understands that there is no warranty for this free
++software.  If the software is modified by someone else and passed on, we
++want its recipients to know that what they have is not the original, so
++that any problems introduced by others will not reflect on the original
++authors' reputations.
++
++  Finally, any free program is threatened constantly by software
++patents.  We wish to avoid the danger that redistributors of a free
++program will individually obtain patent licenses, in effect making the
++program proprietary.  To prevent this, we have made it clear that any
++patent must be licensed for everyone's free use or not licensed at all.
++
++  The precise terms and conditions for copying, distribution and
++modification follow.
++
++		    GNU GENERAL PUBLIC LICENSE
++   TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
++
++  0. This License applies to any program or other work which contains
++a notice placed by the copyright holder saying it may be distributed
++under the terms of this General Public License.  The "Program", below,
++refers to any such program or work, and a "work based on the Program"
++means either the Program or any derivative work under copyright law:
++that is to say, a work containing the Program or a portion of it,
++either verbatim or with modifications and/or translated into another
++language.  (Hereinafter, translation is included without limitation in
++the term "modification".)  Each licensee is addressed as "you".
++
++Activities other than copying, distribution and modification are not
++covered by this License; they are outside its scope.  The act of
++running the Program is not restricted, and the output from the Program
++is covered only if its contents constitute a work based on the
++Program (independent of having been made by running the Program).
++Whether that is true depends on what the Program does.
++
++  1. You may copy and distribute verbatim copies of the Program's
++source code as you receive it, in any medium, provided that you
++conspicuously and appropriately publish on each copy an appropriate
++copyright notice and disclaimer of warranty; keep intact all the
++notices that refer to this License and to the absence of any warranty;
++and give any other recipients of the Program a copy of this License
++along with the Program.
++
++You may charge a fee for the physical act of transferring a copy, and
++you may at your option offer warranty protection in exchange for a fee.
++
++  2. You may modify your copy or copies of the Program or any portion
++of it, thus forming a work based on the Program, and copy and
++distribute such modifications or work under the terms of Section 1
++above, provided that you also meet all of these conditions:
++
++    a) You must cause the modified files to carry prominent notices
++    stating that you changed the files and the date of any change.
++
++    b) You must cause any work that you distribute or publish, that in
++    whole or in part contains or is derived from the Program or any
++    part thereof, to be licensed as a whole at no charge to all third
++    parties under the terms of this License.
++
++    c) If the modified program normally reads commands interactively
++    when run, you must cause it, when started running for such
++    interactive use in the most ordinary way, to print or display an
++    announcement including an appropriate copyright notice and a
++    notice that there is no warranty (or else, saying that you provide
++    a warranty) and that users may redistribute the program under
++    these conditions, and telling the user how to view a copy of this
++    License.  (Exception: if the Program itself is interactive but
++    does not normally print such an announcement, your work based on
++    the Program is not required to print an announcement.)
++
++These requirements apply to the modified work as a whole.  If
++identifiable sections of that work are not derived from the Program,
++and can be reasonably considered independent and separate works in
++themselves, then this License, and its terms, do not apply to those
++sections when you distribute them as separate works.  But when you
++distribute the same sections as part of a whole which is a work based
++on the Program, the distribution of the whole must be on the terms of
++this License, whose permissions for other licensees extend to the
++entire whole, and thus to each and every part regardless of who wrote it.
++
++Thus, it is not the intent of this section to claim rights or contest
++your rights to work written entirely by you; rather, the intent is to
++exercise the right to control the distribution of derivative or
++collective works based on the Program.
++
++In addition, mere aggregation of another work not based on the Program
++with the Program (or with a work based on the Program) on a volume of
++a storage or distribution medium does not bring the other work under
++the scope of this License.
++
++  3. You may copy and distribute the Program (or a work based on it,
++under Section 2) in object code or executable form under the terms of
++Sections 1 and 2 above provided that you also do one of the following:
++
++    a) Accompany it with the complete corresponding machine-readable
++    source code, which must be distributed under the terms of Sections
++    1 and 2 above on a medium customarily used for software interchange; or,
++
++    b) Accompany it with a written offer, valid for at least three
++    years, to give any third party, for a charge no more than your
++    cost of physically performing source distribution, a complete
++    machine-readable copy of the corresponding source code, to be
++    distributed under the terms of Sections 1 and 2 above on a medium
++    customarily used for software interchange; or,
++
++    c) Accompany it with the information you received as to the offer
++    to distribute corresponding source code.  (This alternative is
++    allowed only for noncommercial distribution and only if you
++    received the program in object code or executable form with such
++    an offer, in accord with Subsection b above.)
++
++The source code for a work means the preferred form of the work for
++making modifications to it.  For an executable work, complete source
++code means all the source code for all modules it contains, plus any
++associated interface definition files, plus the scripts used to
++control compilation and installation of the executable.  However, as a
++special exception, the source code distributed need not include
++anything that is normally distributed (in either source or binary
++form) with the major components (compiler, kernel, and so on) of the
++operating system on which the executable runs, unless that component
++itself accompanies the executable.
++
++If distribution of executable or object code is made by offering
++access to copy from a designated place, then offering equivalent
++access to copy the source code from the same place counts as
++distribution of the source code, even though third parties are not
++compelled to copy the source along with the object code.
++
++  4. You may not copy, modify, sublicense, or distribute the Program
++except as expressly provided under this License.  Any attempt
++otherwise to copy, modify, sublicense or distribute the Program is
++void, and will automatically terminate your rights under this License.
++However, parties who have received copies, or rights, from you under
++this License will not have their licenses terminated so long as such
++parties remain in full compliance.
++
++  5. You are not required to accept this License, since you have not
++signed it.  However, nothing else grants you permission to modify or
++distribute the Program or its derivative works.  These actions are
++prohibited by law if you do not accept this License.  Therefore, by
++modifying or distributing the Program (or any work based on the
++Program), you indicate your acceptance of this License to do so, and
++all its terms and conditions for copying, distributing or modifying
++the Program or works based on it.
++
++  6. Each time you redistribute the Program (or any work based on the
++Program), the recipient automatically receives a license from the
++original licensor to copy, distribute or modify the Program subject to
++these terms and conditions.  You may not impose any further
++restrictions on the recipients' exercise of the rights granted herein.
++You are not responsible for enforcing compliance by third parties to
++this License.
++
++  7. If, as a consequence of a court judgment or allegation of patent
++infringement or for any other reason (not limited to patent issues),
++conditions are imposed on you (whether by court order, agreement or
++otherwise) that contradict the conditions of this License, they do not
++excuse you from the conditions of this License.  If you cannot
++distribute so as to satisfy simultaneously your obligations under this
++License and any other pertinent obligations, then as a consequence you
++may not distribute the Program at all.  For example, if a patent
++license would not permit royalty-free redistribution of the Program by
++all those who receive copies directly or indirectly through you, then
++the only way you could satisfy both it and this License would be to
++refrain entirely from distribution of the Program.
++
++If any portion of this section is held invalid or unenforceable under
++any particular circumstance, the balance of the section is intended to
++apply and the section as a whole is intended to apply in other
++circumstances.
++
++It is not the purpose of this section to induce you to infringe any
++patents or other property right claims or to contest validity of any
++such claims; this section has the sole purpose of protecting the
++integrity of the free software distribution system, which is
++implemented by public license practices.  Many people have made
++generous contributions to the wide range of software distributed
++through that system in reliance on consistent application of that
++system; it is up to the author/donor to decide if he or she is willing
++to distribute software through any other system and a licensee cannot
++impose that choice.
++
++This section is intended to make thoroughly clear what is believed to
++be a consequence of the rest of this License.
++
++  8. If the distribution and/or use of the Program is restricted in
++certain countries either by patents or by copyrighted interfaces, the
++original copyright holder who places the Program under this License
++may add an explicit geographical distribution limitation excluding
++those countries, so that distribution is permitted only in or among
++countries not thus excluded.  In such case, this License incorporates
++the limitation as if written in the body of this License.
++
++  9. The Free Software Foundation may publish revised and/or new versions
++of the General Public License from time to time.  Such new versions will
++be similar in spirit to the present version, but may differ in detail to
++address new problems or concerns.
++
++Each version is given a distinguishing version number.  If the Program
++specifies a version number of this License which applies to it and "any
++later version", you have the option of following the terms and conditions
++either of that version or of any later version published by the Free
++Software Foundation.  If the Program does not specify a version number of
++this License, you may choose any version ever published by the Free Software
++Foundation.
++
++  10. If you wish to incorporate parts of the Program into other free
++programs whose distribution conditions are different, write to the author
++to ask for permission.  For software which is copyrighted by the Free
++Software Foundation, write to the Free Software Foundation; we sometimes
++make exceptions for this.  Our decision will be guided by the two goals
++of preserving the free status of all derivatives of our free software and
++of promoting the sharing and reuse of software generally.
++
++			    NO WARRANTY
++
++  11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY
++FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.  EXCEPT WHEN
++OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
++PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED
++OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
++MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  THE ENTIRE RISK AS
++TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.  SHOULD THE
++PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
++REPAIR OR CORRECTION.
++
++  12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING
++WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
++REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
++INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
++OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
++TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
++YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
++PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
++POSSIBILITY OF SUCH DAMAGES.
++
++		     END OF TERMS AND CONDITIONS
++
++	    How to Apply These Terms to Your New Programs
++
++  If you develop a new program, and you want it to be of the greatest
++possible use to the public, the best way to achieve this is to make it
++free software which everyone can redistribute and change under these terms.
++
++  To do so, attach the following notices to the program.  It is safest
++to attach them to the start of each source file to most effectively
++convey the exclusion of warranty; and each file should have at least
++the "copyright" line and a pointer to where the full notice is found.
++
++    <one line to give the program's name and a brief idea of what it does.>
++    Copyright (C) <year>  <name of author>
++
++    This program is free software; you can redistribute it and/or modify
++    it under the terms of the GNU General Public License as published by
++    the Free Software Foundation; either version 2 of the License, or
++    (at your option) any later version.
++
++    This program is distributed in the hope that it will be useful,
++    but WITHOUT ANY WARRANTY; without even the implied warranty of
++    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++    GNU General Public License for more details.
++
++    You should have received a copy of the GNU General Public License along
++    with this program; if not, write to the Free Software Foundation, Inc.,
++    51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
++
++Also add information on how to contact you by electronic and paper mail.
++
++If the program is interactive, make it output a short notice like this
++when it starts in an interactive mode:
++
++    Gnomovision version 69, Copyright (C) year name of author
++    Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
++    This is free software, and you are welcome to redistribute it
++    under certain conditions; type `show c' for details.
++
++The hypothetical commands `show w' and `show c' should show the appropriate
++parts of the General Public License.  Of course, the commands you use may
++be called something other than `show w' and `show c'; they could even be
++mouse-clicks or menu items--whatever suits your program.
++
++You should also get your employer (if you work as a programmer) or your
++school, if any, to sign a "copyright disclaimer" for the program, if
++necessary.  Here is a sample; alter the names:
++
++  Yoyodyne, Inc., hereby disclaims all copyright interest in the program
++  `Gnomovision' (which makes passes at compilers) written by James Hacker.
++
++  <signature of Ty Coon>, 1 April 1989
++  Ty Coon, President of Vice
++
++This General Public License does not permit incorporating your program into
++proprietary programs.  If your program is a subroutine library, you may
++consider it more useful to permit linking proprietary applications with the
++library.  If this is what you want to do, use the GNU Lesser General
++Public License instead of this License.
+-- 
+1.7.8.5
+
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0002-add-setdpi-Xinit.d-script.patch new file +112 -0

112 lines not on this page · raw message

meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0003-add-89xdgautostart-Xsession.d-script.patch new file +29 -0
new file mode 100644
index 0000000..bf806a9
@@ -0,0 +1,29 @@
+From a93a86c2ff1ca5eb35615f4e1568409ff342aa7f Mon Sep 17 00:00:00 2001
+From: Martin Jansa <[email protected]>
+Date: Wed, 11 Apr 2012 14:29:41 +0200
+Subject: [PATCH 03/12] add 89xdgautostart Xsession.d script
+
+Signed-off-by: Martin Jansa <[email protected]>
+---
+ X11/Xsession.d/89xdgautostart |    9 +++++++++
+ 1 files changed, 9 insertions(+), 0 deletions(-)
+ create mode 100644 X11/Xsession.d/89xdgautostart
+
+diff --git a/X11/Xsession.d/89xdgautostart b/X11/Xsession.d/89xdgautostart
+new file mode 100644
+index 0000000..9886f9f
+--- /dev/null
++++ b/X11/Xsession.d/89xdgautostart
+@@ -0,0 +1,9 @@
++#!/bin/sh
++
++XDGAUTOSTART=/etc/xdg/autostart
++if [ -d $XDGAUTOSTART ] ; then
++    for SCRIPT in $XDGAUTOSTART/*; do
++        CMD=`grep ^Exec= $SCRIPT | cut -d '=' -f 2`
++        $CMD &
++    done
++fi
+-- 
+1.7.8.5
+
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0004-add-Ts_Calibrate_xinput_calibrator-Xsession.d-script.patch new file +27 -0
new file mode 100644
index 0000000..135b2a6
@@ -0,0 +1,27 @@
+From 2877156d5bbc11f8d8e8d6aafd138173d2a4bd3b Mon Sep 17 00:00:00 2001
+From: Martin Jansa <[email protected]>
+Date: Wed, 11 Apr 2012 14:31:34 +0200
+Subject: [PATCH 04/12] add Ts_Calibrate_xinput_calibrator Xsession.d script
+
+Signed-off-by: Martin Jansa <[email protected]>
+---
+ X11/Xsession.d/89xTs_Calibrate_xinput_calibrator |    7 +++++++
+ 1 files changed, 7 insertions(+), 0 deletions(-)
+ create mode 100644 X11/Xsession.d/89xTs_Calibrate_xinput_calibrator
+
+diff --git a/X11/Xsession.d/89xTs_Calibrate_xinput_calibrator b/X11/Xsession.d/89xTs_Calibrate_xinput_calibrator
+new file mode 100644
+index 0000000..6ef4d1e
+--- /dev/null
++++ b/X11/Xsession.d/89xTs_Calibrate_xinput_calibrator
+@@ -0,0 +1,7 @@
++#!/bin/sh
++
++if [ -e /usr/bin/xinput_calibrator_once.sh ] ; then
++  if [ -e /etc/pointercal.xinput ] ; then
++    /usr/bin/xinput_calibrator_once.sh
++  fi
++fi
+-- 
+1.7.8.5
+
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0005-add-XWindowManager-Xsession.d-script.patch new file +26 -0
new file mode 100644
index 0000000..f5c2c78
@@ -0,0 +1,26 @@
+From b01a532ebb525552e23d7169a2aeb55c42b3ec99 Mon Sep 17 00:00:00 2001
+From: Martin Jansa <[email protected]>
+Date: Wed, 11 Apr 2012 14:32:13 +0200
+Subject: [PATCH 05/12] add XWindowManager Xsession.d script
+
+Signed-off-by: Martin Jansa <[email protected]>
+---
+ X11/Xsession.d/90xXWindowManager |    6 ++++++
+ 1 files changed, 6 insertions(+), 0 deletions(-)
+ create mode 100644 X11/Xsession.d/90xXWindowManager
+
+diff --git a/X11/Xsession.d/90xXWindowManager b/X11/Xsession.d/90xXWindowManager
+new file mode 100644
+index 0000000..3df8435
+--- /dev/null
++++ b/X11/Xsession.d/90xXWindowManager
+@@ -0,0 +1,6 @@
++#!/bin/sh
++if [ -x $HOME/.Xsession ]; then
++    exec $HOME/.Xsession
++else
++    exec /usr/bin/x-window-manager
++fi
+-- 
+1.7.8.5
+
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0006-add-support-for-etc-X11-xserver-system.patch new file +26 -0
new file mode 100644
index 0000000..7ee8572
@@ -0,0 +1,26 @@
+From 0c42e1fb84cc2bfe768bed17f3b979aca868cf64 Mon Sep 17 00:00:00 2001
+From: Martin Jansa <[email protected]>
+Date: Wed, 11 Apr 2012 14:34:43 +0200
+Subject: [PATCH 06/12] add support for /etc/X11/xserver-system
+
+Signed-off-by: Martin Jansa <[email protected]>
+---
+ X11/xserver-common |    5 +++++
+ 1 files changed, 5 insertions(+), 0 deletions(-)
+
+diff --git a/X11/xserver-common b/X11/xserver-common
+index 4c7ed6e..6d8c9df 100644
+--- a/X11/xserver-common
++++ b/X11/xserver-common
+@@ -204,3 +204,8 @@ fi
+ if [ "$XSERVER" != "Xorg" ] ; then
+     ARGS="$ARGS $MOUSE $KDRIVEARGS"
+ fi
++
++# let a local script modify the variables                    
++if [ -e /etc/X11/xserver-system ] ; then                    
++       . /etc/X11/xserver-system                    
++fi                    
+-- 
+1.7.8.5
+
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0007-use-own-functions-file-instead-etc-init.d-functions.patch new file +87 -0

87 lines not on this page · raw message

meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0008-xserver-common-add-dpi-and-nocursor-params-for-gta01.patch new file +40 -0
new file mode 100644
index 0000000..e35e4a7
@@ -0,0 +1,40 @@
+From 0ee7bf87e0c83abc79de3a99dfa3c87dd5c5b229 Mon Sep 17 00:00:00 2001
+From: Martin Jansa <[email protected]>
+Date: Wed, 11 Apr 2012 14:37:29 +0200
+Subject: [PATCH 08/12] xserver-common: add dpi and nocursor params for gta01
+ and gta02
+
+Signed-off-by: Martin Jansa <[email protected]>
+---
+ X11/xserver-common |    8 ++++++--
+ 1 files changed, 6 insertions(+), 2 deletions(-)
+
+diff --git a/X11/xserver-common b/X11/xserver-common
+index de92bb7..f76fa5f 100644
+--- a/X11/xserver-common
++++ b/X11/xserver-common
+@@ -133,15 +133,19 @@ else
+             ARGS="$ARGS -screen ${SCREEN_SIZE}"
+             DPI="225" ;;
+         "gta01" )
+-            DPI="285"
++            DPI="280"
+             if [ "$XSERVER" != "Xorg" ] ; then
+                 ARGS="$ARGS -screen 480x640"
++            else
++                ARGS="$ARGS -dpi ${DPI} -nocursor"
+             fi
+             ;;
+         "gta02")
+-            DPI="285"
++            DPI="280"
+             if [ "$XSERVER" != "Xorg" ] ; then
+                 ARGS="$ARGS -screen ${SCREEN_SIZE}"
++            else
++                ARGS="$ARGS -dpi ${DPI} -nocursor"
+             fi
+             ;;
+         "motorola_ezx_platform")
+-- 
+1.7.8.5
+
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0009-xserver-common-add-support-for-n900-alias-nokia_rx-5.patch new file +32 -0
new file mode 100644
index 0000000..1a0bde8
@@ -0,0 +1,32 @@
+From 6d6caecb7172b9b33e7364564b0e6eabf67b6e8b Mon Sep 17 00:00:00 2001
+From: Martin Jansa <[email protected]>
+Date: Wed, 11 Apr 2012 14:40:14 +0200
+Subject: [PATCH 09/12] xserver-common: add support for n900 alias
+ nokia_rx-51_board
+
+Signed-off-by: Martin Jansa <[email protected]>
+---
+ X11/xserver-common |    7 +++++++
+ 1 files changed, 7 insertions(+), 0 deletions(-)
+
+diff --git a/X11/xserver-common b/X11/xserver-common
+index f76fa5f..86ed17f 100644
+--- a/X11/xserver-common
++++ b/X11/xserver-common
+@@ -132,6 +132,13 @@ else
+         "nokia_n800" | "nokia_rx-44" | "nokia_n770")
+             ARGS="$ARGS -screen ${SCREEN_SIZE}"
+             DPI="225" ;;
++        "nokia_rx-51_board" )                                     
++            DPI="267"                                    
++            if [ "$XSERVER" != "Xorg" ] ; then                    
++                ARGS="$ARGS -screen ${SCREEN_SIZE}"               
++            else                                                  
++                ARGS="$ARGS -dpi ${DPI} -nocursor"       
++            fi ;;                                                    
+         "gta01" )
+             DPI="280"
+             if [ "$XSERVER" != "Xorg" ] ; then
+-- 
+1.7.8.5
+
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0010-xserver-common-add-support-for-nexus-S-alias-herring.patch new file +27 -0
new file mode 100644
index 0000000..688be40
@@ -0,0 +1,27 @@
+From 52003e6b52b1417c1a0e57243d83349addcdacf6 Mon Sep 17 00:00:00 2001
+From: Martin Jansa <[email protected]>
+Date: Wed, 11 Apr 2012 14:40:44 +0200
+Subject: [PATCH 10/12] xserver-common: add support for nexus S alias herring
+
+Signed-off-by: Martin Jansa <[email protected]>
+---
+ X11/xserver-common |    3 +++
+ 1 files changed, 3 insertions(+), 0 deletions(-)
+
+diff --git a/X11/xserver-common b/X11/xserver-common
+index 86ed17f..5c9a6eb 100644
+--- a/X11/xserver-common
++++ b/X11/xserver-common
+@@ -126,6 +126,9 @@ else
+         "htc_tornado")
+             ARGS="$ARGS -hide-cursor"
+             DPI="100" ;;
++        "herring")
++            DPI="235"
++            ARGS="$ARGS -dpi ${DPI} -nocursor";;
+         "generic_omap1510/1610/1710")
+             ARGS="$ARGS -screen ${SCREEN_SIZE}"
+             DPI="225" ;;
+-- 
+1.7.8.5
+
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0011-xserver-common-add-support-for-nexus-one-alias-mahim.patch new file +28 -0
new file mode 100644
index 0000000..f80456d
@@ -0,0 +1,28 @@
+From 0ecc978b7d8cb6867646fb2a29523ebef3afa016 Mon Sep 17 00:00:00 2001
+From: Martin Jansa <[email protected]>
+Date: Wed, 11 Apr 2012 14:41:06 +0200
+Subject: [PATCH 11/12] xserver-common: add support for nexus one alias
+ mahimahi
+
+Signed-off-by: Martin Jansa <[email protected]>
+---
+ X11/xserver-common |    3 +++
+ 1 files changed, 3 insertions(+), 0 deletions(-)
+
+diff --git a/X11/xserver-common b/X11/xserver-common
+index 5c9a6eb..55594fd 100644
+--- a/X11/xserver-common
++++ b/X11/xserver-common
+@@ -129,6 +129,9 @@ else
+         "herring")
+             DPI="235"
+             ARGS="$ARGS -dpi ${DPI} -nocursor";;
++        "mahimahi")
++            DPI="254"
++            ARGS="$ARGS -dpi ${DPI}";;
+         "generic_omap1510/1610/1710")
+             ARGS="$ARGS -screen ${SCREEN_SIZE}"
+             DPI="225" ;;
+-- 
+1.7.8.5
+
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/0012-xserver-common-add-support-for-gta04-alias-OpenPhoen.patch new file +33 -0
new file mode 100644
index 0000000..54a0329
@@ -0,0 +1,33 @@
+From d194f0302582f1ca599f2ea58c15e15f4fd6bdef Mon Sep 17 00:00:00 2001
+From: Martin Jansa <[email protected]>
+Date: Wed, 11 Apr 2012 14:41:52 +0200
+Subject: [PATCH 12/12] xserver-common: add support for gta04 alias
+ OpenPhoenux
+
+Signed-off-by: Martin Jansa <[email protected]>
+---
+ X11/xserver-common |    8 ++++++++
+ 1 files changed, 8 insertions(+), 0 deletions(-)
+
+diff --git a/X11/xserver-common b/X11/xserver-common
+index 55594fd..434333e 100644
+--- a/X11/xserver-common
++++ b/X11/xserver-common
+@@ -161,6 +161,14 @@ else
+                 ARGS="$ARGS -dpi ${DPI} -nocursor"
+             fi
+             ;;
++        "gta04")
++            DPI="280"
++            if [ "$XSERVER" != "Xorg" ] ; then
++                ARGS="$ARGS -screen ${SCREEN_SIZE}"
++            else
++                ARGS="$ARGS -dpi ${DPI} -nocursor"
++            fi
++            ;;
+         "motorola_ezx_platform")
+             ARGS="$ARGS -screen 240x320"
+             DPI="170" ;;
+-- 
+1.7.8.5
+
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/89xTs_Calibrate.xinput_calibrator.patch deleted +0 -12
deleted file mode 100644
index c04ad96..0000000
@@ -1,12 +0,0 @@
-Index: xserver-common/X11/Xsession.d/89xTs_Calibrate_xinput_calibrator
-===================================================================
---- xserver-common/X11/Xsession.d/89xTs_Calibrate_xinput_calibrator	(revision 0)
-+++ xserver-common/X11/Xsession.d/89xTs_Calibrate_xinput_calibrator	(revision 0)
-@@ -0,0 +1,7 @@
-+#!/bin/sh
-+
-+if [ -e /usr/bin/xinput_calibrator_once.sh ] ; then
-+  if [ -e /etc/pointercal.xinput ] ; then
-+    /usr/bin/xinput_calibrator_once.sh
-+  fi
-+fi
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/89xdgautostart.sh deleted +0 -9
deleted file mode 100644
index 9886f9f..0000000
@@ -1,9 +0,0 @@
-#!/bin/sh
-
-XDGAUTOSTART=/etc/xdg/autostart
-if [ -d $XDGAUTOSTART ] ; then
-    for SCRIPT in $XDGAUTOSTART/*; do
-        CMD=`grep ^Exec= $SCRIPT | cut -d '=' -f 2`
-        $CMD &
-    done
-fi
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/90xXWindowManager.patch deleted +0 -11
deleted file mode 100644
index be5f5ce..0000000
@@ -1,11 +0,0 @@
-Index: xserver-common/X11/Xsession.d/90xXWindowManager
-===================================================================
---- xserver-common/X11/Xsession.d/90xXWindowManager	(revision 0)
-+++ xserver-common/X11/Xsession.d/90xXWindowManager	(revision 0)
-@@ -0,0 +1,6 @@
-+#!/bin/sh
-+if [ -x $HOME/.Xsession ]; then
-+    exec $HOME/.Xsession
-+else
-+    exec /usr/bin/x-window-manager
-+fi
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.add.dpi.for.gta.patch deleted +0 -29
deleted file mode 100644
index f6e36d9..0000000
@@ -1,29 +0,0 @@
-xdpyinfo returns 96, but 285 is right value (but 280 is used as it renders 4 columns of illume icons instead of 3 and empty space)
-
-diff -uNr xserver-common-1.33.orig//X11/xserver-common xserver-common-1.33/X11/xserver-common
---- xserver-common-1.33.orig//X11/xserver-common	2010-04-28 23:27:10.000000000 +0200
-+++ xserver-common-1.33/X11/xserver-common	2010-04-28 23:29:07.000000000 +0200
-@@ -133,19 +133,19 @@
-             ARGS="$ARGS -screen ${SCREEN_SIZE}"
-             DPI="225" ;;
-         "gta01" )
--            DPI="285"
-+            DPI="280"
-             if [ "$XSERVER" != "Xorg" ] ; then
-                 ARGS="$ARGS -screen 480x640"
-             else
--                ARGS="$ARGS -nocursor"
-+                ARGS="$ARGS -dpi ${DPI} -nocursor"
-             fi
-             ;;
-         "gta02")
--            DPI="285"
-+            DPI="280"
-             if [ "$XSERVER" != "Xorg" ] ; then
-                 ARGS="$ARGS -screen ${SCREEN_SIZE}"
-             else
--                ARGS="$ARGS -nocursor"
-+                ARGS="$ARGS -dpi ${DPI} -nocursor"
-             fi
-             ;;
-         "motorola_ezx_platform")
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.add.nocursor.for.gta.patch deleted +0 -20
deleted file mode 100644
index bd16efc..0000000
@@ -1,20 +0,0 @@
-diff -uNr xserver-common-1.33.orig//X11/xserver-common xserver-common-1.33/X11/xserver-common
---- xserver-common-1.33.orig//X11/xserver-common	2010-04-28 10:44:23.000000000 +0200
-+++ xserver-common-1.33/X11/xserver-common	2010-04-28 10:46:41.000000000 +0200
-@@ -136,12 +136,16 @@
-             DPI="285"
-             if [ "$XSERVER" != "Xorg" ] ; then
-                 ARGS="$ARGS -screen 480x640"
-+            else
-+                ARGS="$ARGS -nocursor"
-             fi
-             ;;
-         "gta02")
-             DPI="285"
-             if [ "$XSERVER" != "Xorg" ] ; then
-                 ARGS="$ARGS -screen ${SCREEN_SIZE}"
-+            else
-+                ARGS="$ARGS -nocursor"
-             fi
-             ;;
-         "motorola_ezx_platform")
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.add.xserver-system.patch deleted +0 -12
deleted file mode 100644
index 5d9d5d1..0000000
@@ -1,12 +0,0 @@
-diff -uNr xserver-common-1.33.orig//X11/xserver-common xserver-common-1.33/X11/xserver-common
---- xserver-common-1.33.orig//X11/xserver-common        2010-04-28 23:27:10.000000000 +0200
-+++ xserver-common-1.33/X11/xserver-common      2010-04-28 23:29:07.000000000 +0200
-@@ -192,3 +196,8 @@
- if [ "$XSERVER" != "Xorg" ] ; then
-     ARGS="$ARGS $MOUSE"
- fi
-+
-+# let a local script modify the variables                    
-+if [ -e /etc/X11/xserver-system ] ; then                    
-+       . /etc/X11/xserver-system                    
-+fi                    
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.gta04.patch deleted +0 -32
deleted file mode 100644
index 8a17c9a..0000000
@@ -1,32 +0,0 @@
-From 95d741d6849a2faddf8c1e930c7250ead90e7bed Mon Sep 17 00:00:00 2001
-From: Klaus Kurzmann <[email protected]>
-Date: Thu, 20 Oct 2011 09:05:43 +0200
-Subject: [PATCH] gta04
-
-Signed-off-by: Klaus Kurzmann <[email protected]>
----
- X11/xserver-common |    8 ++++++++
- 1 files changed, 8 insertions(+), 0 deletions(-)
-
-diff --git a/X11/xserver-common b/X11/xserver-common
-index 448b262..208bbfd 100644
---- a/X11/xserver-common
-+++ b/X11/xserver-common
-@@ -161,6 +161,14 @@ else
-                 ARGS="$ARGS -dpi ${DPI} -nocursor"
-             fi
-             ;;
-+        "gta04")
-+            DPI="280"
-+            if [ "$XSERVER" != "Xorg" ] ; then
-+                ARGS="$ARGS -screen ${SCREEN_SIZE}"
-+            else
-+                ARGS="$ARGS -dpi ${DPI} -nocursor"
-+            fi
-+            ;;
-         "motorola_ezx_platform")
-             ARGS="$ARGS -screen 240x320"
-             DPI="170" ;;
--- 
-1.7.7
-
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.n900.patch deleted +0 -17
deleted file mode 100644
index 4d36f5f..0000000
@@ -1,17 +0,0 @@
-diff -uri xserver-common-1.33.orig/X11/xserver-common xserver-common-1.33/X11/xserver-common
---- xserver-common-1.33.orig/X11/xserver-common	2010-09-14 17:10:35.955430177 +0200
-+++ xserver-common-1.33/X11/xserver-common	2010-09-14 17:17:12.484423440 +0200
-@@ -132,6 +132,13 @@
-         "nokia_n800" | "nokia_rx-44" | "nokia_n770")
-             ARGS="$ARGS -screen ${SCREEN_SIZE}"
-             DPI="225" ;;
-+        "nokia_rx-51_board" )                                     
-+            DPI="267"                                    
-+            if [ "$XSERVER" != "Xorg" ] ; then                    
-+                ARGS="$ARGS -screen ${SCREEN_SIZE}"               
-+            else                                                  
-+                ARGS="$ARGS -dpi ${DPI} -nocursor"       
-+            fi ;;                                                    
-         "gta01" )
-             DPI="280"
-             if [ "$XSERVER" != "Xorg" ] ; then
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.nexusone.patch deleted +0 -14
deleted file mode 100644
index 7d528ae..0000000
@@ -1,14 +0,0 @@
-Index: xserver-common-1.34/X11/xserver-common
-===================================================================
---- xserver-common-1.34.orig/X11/xserver-common	2011-10-10 22:36:14.163129002 +0200
-+++ xserver-common-1.34/X11/xserver-common	2011-10-10 22:37:47.513129001 +0200
-@@ -129,6 +129,9 @@
-         "herring")
-             DPI="235"
-             ARGS="$ARGS -dpi ${DPI} -nocursor";;
-+        "mahimahi")
-+            DPI="254"
-+            ARGS="$ARGS -dpi ${DPI}";;
-         "generic_omap1510/1610/1710")
-             ARGS="$ARGS -screen ${SCREEN_SIZE}"
-             DPI="225" ;;
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/Xserver.nexuss.patch deleted +0 -14
deleted file mode 100644
index 1e564ce..0000000
@@ -1,14 +0,0 @@
-Index: xserver-common-1.34/X11/xserver-common
-===================================================================
---- xserver-common-1.34.orig/X11/xserver-common	2011-10-09 14:57:10.716896996 +0200
-+++ xserver-common-1.34/X11/xserver-common	2011-10-09 14:57:31.226897012 +0200
-@@ -126,6 +126,9 @@
-         "htc_tornado")
-             ARGS="$ARGS -hide-cursor"
-             DPI="100" ;;
-+        "herring")
-+            DPI="235"
-+            ARGS="$ARGS -dpi ${DPI} -nocursor";;
-         "generic_omap1510/1610/1710")
-             ARGS="$ARGS -screen ${SCREEN_SIZE}"
-             DPI="225" ;;
meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/gplv2-license.patch deleted +0 -353

353 lines not on this page · raw message

meta-oe/recipes-graphics/xserver-common/xserver-common-1.34/setDPI.sh deleted +0 -92

92 lines not on this page · raw message

meta-oe/recipes-graphics/xserver-common/xserver-common_1.34.bb +13 -16
index 4f99a90..b0823bf 100644
@@ -2,7 +2,7 @@ DESCRIPTION = "Common X11 scripts and support files"
 LICENSE = "GPLv2"
 LIC_FILES_CHKSUM = "file://COPYING;md5=751419260aa954499f7abaabaa882bbe"
 
-PR = "r5"
+PR = "r6"
 
 # we are using a gpe-style Makefile
 inherit gpe
@@ -11,24 +11,21 @@ SRC_URI[md5sum] = "82f2f84cd96610e8f7b92c700cd31c14"
 SRC_URI[sha256sum] = "cd04c33418f776b1e13fcc7af3d6bd0c7cccd03fbabd7dbcd97f88166cc34210"
 
 SRC_URI_append = " \
-                   file://gplv2-license.patch \
-                   file://setDPI.sh \
-                   file://89xdgautostart.sh \
-                   file://89xTs_Calibrate.xinput_calibrator.patch \
-                   file://90xXWindowManager.patch \
-                   file://Xserver.add.xserver-system.patch \
-                   file://Xserver.add.nocursor.for.gta.patch \
-                   file://Xserver.add.dpi.for.gta.patch \
-                   file://Xserver.n900.patch \
-                   file://Xserver.nexuss.patch \
-                   file://Xserver.nexusone.patch \
-                   file://Xserver.gta04.patch \
+  file://0001-COPYING-add-GPLv2-license-file.patch \
+  file://0002-add-setdpi-Xinit.d-script.patch \
+  file://0003-add-89xdgautostart-Xsession.d-script.patch \
+  file://0004-add-Ts_Calibrate_xinput_calibrator-Xsession.d-script.patch \
+  file://0005-add-XWindowManager-Xsession.d-script.patch \
+  file://0006-add-support-for-etc-X11-xserver-system.patch \
+  file://0007-use-own-functions-file-instead-etc-init.d-functions.patch \
+  file://0008-xserver-common-add-dpi-and-nocursor-params-for-gta01.patch \
+  file://0009-xserver-common-add-support-for-n900-alias-nokia_rx-5.patch \
+  file://0010-xserver-common-add-support-for-nexus-S-alias-herring.patch \
+  file://0011-xserver-common-add-support-for-nexus-one-alias-mahim.patch \
+  file://0012-xserver-common-add-support-for-gta04-alias-OpenPhoen.patch \
 "
 
-
 do_install_append() {
-        install -m 0755 "${WORKDIR}/setDPI.sh" "${D}/etc/X11/Xinit.d/50setdpi"
-        install -m 0755 "${WORKDIR}/89xdgautostart.sh" "${D}/etc/X11/Xsession.d/89xdgautostart"
         sed -i 's:^BINDIR=.*$:BINDIR=${bindir}:' ${D}/etc/X11/xserver-common
 }
 
Signature · 1 line
1.7.8.5
Acked-by on v1 1/1
#7 lore raw

Re: [PATCH] xserver-common: use git patches and add functions file

Quoted 3 lines · Martin Jansa

* otherwise we were depending on initscripts to provide it without RDEPENDing on it

Signature · 3 lines
Otavio Salvador                             O.S. Systems
E-mail: [email protected]  http://www.ossystems.com.br
Mobile: +55 53 9981-7854              http://projetos.ossystems.com.br