Skip to contentSkip to conversation

ARM: dts: add initial Colibri VF61 board support

PATCH Superseded stefan at agner.ch 4 participants 6 messages Apr 2, 2014 – Apr 3, 2014

Subsystems (2)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

cover ARM: dts: add initial Colibri VF61 board support

From: Stefan Agner <[email protected]>

This patches add initial support for Toradex Colibri VF61 computer-on-module.

Stefan Agner (2):
of: add vendor prefix for Toradex AG
ARM: dts: add initial Colibri VF61 board support

 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/vf610-colibri.dts                | 123 +++++++++++++++++++++
 3 files changed, 125 insertions(+)
 create mode 100644 arch/arm/boot/dts/vf610-colibri.dts
Signature · 1 line
1.9.1
#1 lore raw

PATCH 1/2 of: add vendor prefix for Toradex AG

From: Stefan Agner <[email protected]>

Adds toradex to the list of DT vendor prefixes.

---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
index e9d19e2..6a68eae 100644
@@ -91,6 +91,7 @@ ti	Texas Instruments
 tlm	Trusted Logic Mobility
 toshiba	Toshiba Corporation
 toumaz	Toumaz
+toradex	Toradex AG
 v3	V3 Semiconductor
 via	VIA Technologies, Inc.
 voipac	Voipac Technologies s.r.o.
Signature · 1 line
1.9.1
#4 lore raw

PATCH 2/2 ARM: dts: add initial Colibri VF61 board support

In reply to stefan at agner.ch

From: Stefan Agner <[email protected]>

Add initial Toradex Colibri VF61 board support. Ethernet, UART and SDHC cards are working. Cache latencies need to be a bit higher than vf610.dtsi suggests. Those values are validated by running multiple memory tests.

---
 arch/arm/boot/dts/Makefile          |   1 +
 arch/arm/boot/dts/vf610-colibri.dts | 123 ++++++++++++++++++++++++++++++++++++
 2 files changed, 124 insertions(+)
 create mode 100644 arch/arm/boot/dts/vf610-colibri.dts
arch/arm/boot/dts/Makefile +1 -0
index 23d7768..81b3885 100644
@@ -190,6 +190,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx6q-udoo.dtb \
 	imx6q-wandboard.dtb \
 	imx6sl-evk.dtb \
+	vf610-colibri.dtb \
 	vf610-cosmic.dtb \
 	vf610-twr.dtb
 dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
arch/arm/boot/dts/vf610-colibri.dts new file +123 -0

123 lines not on this page · raw message

Signature · 1 line
1.9.1
#2 lore raw

PATCH 1/2 of: add vendor prefix for Toradex AG

In reply to stefan at agner.ch
Quoted 5 lines · On Wed, Apr 2, 2014 at 11:47 AM, <[email protected]> wrote:

From: Stefan Agner <[email protected]>

Adds toradex to the list of DT vendor prefixes.

Quoted 24 lines
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -1
index e9d19e2..6a68eae 100644
@@ -91,6 +91,7 @@ ti    Texas Instruments
 tlm    Trusted Logic Mobility
 toshiba        Toshiba Corporation
 toumaz Toumaz
+toradex        Toradex AG
 v3     V3 Semiconductor
 via    VIA Technologies, Inc.
 voipac Voipac Technologies s.r.o.
--

1.9.1

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#5 lore raw

PATCH 2/2 ARM: dts: add initial Colibri VF61 board support

In reply to stefan at agner.ch
Quoted 8 lines · stefan at agner.ch

From: Stefan Agner <[email protected]>

Add initial Toradex Colibri VF61 board support. Ethernet, UART and SDHC cards are working. Cache latencies need to be a bit higher than vf610.dtsi suggests. Those values are validated by running multiple memory tests.

Looks good to me. Only one minor comment below.

Quoted 49 lines
---
 arch/arm/boot/dts/Makefile          |   1 +
 arch/arm/boot/dts/vf610-colibri.dts | 123 ++++++++++++++++++++++++++++++++++++
 2 files changed, 124 insertions(+)
 create mode 100644 arch/arm/boot/dts/vf610-colibri.dts
arch/arm/boot/dts/Makefile +1 -0
index 23d7768..81b3885 100644
@@ -190,6 +190,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx6q-udoo.dtb \
 	imx6q-wandboard.dtb \
 	imx6sl-evk.dtb \
+	vf610-colibri.dtb \
 	vf610-cosmic.dtb \
 	vf610-twr.dtb
 dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
arch/arm/boot/dts/vf610-colibri.dts new file +25 -0
new file mode 100644
index 0000000..3ac34e6
@@ -0,0 +1,123 @@
+/*
+ * Copyright 2014 Toradex AG
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+/dts-v1/;
+#include "vf610.dtsi"
+
+/ {
+	model = "Toradex Colibri VF61 COM";
+	compatible = "toradex,vf610-colibri", "fsl,vf610";
+
+	chosen {
+		bootargs = "console=ttyLP0,115200";
+	};
+
+	memory {
+		reg = <0x80000000 0x10000000>;
+	};
+
+	clocks {

arch/arm/boot/dts/vf610-colibri.dts line 35

Quoted 10 lines
arch/arm/boot/dts/vf610-colibri.dts new file +10 -0
+		enet_ext {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+		};
+	};
+
+};
+
+&iomuxc {

I would suggest to put this node at the bottom of the file, since it will have a lot more data than other nodes. Doing so will make reading of the file a little easier.

Shawn

Quoted 91 lines
arch/arm/boot/dts/vf610-colibri.dts new file +88 -0
+	vf610-colibri {
+		pinctrl_esdhc1: esdhc1grp {
+			fsl,fsl,pins = <
+				VF610_PAD_PTA24__ESDHC1_CLK	0x31ef
+				VF610_PAD_PTA25__ESDHC1_CMD	0x31ef
+				VF610_PAD_PTA26__ESDHC1_DAT0	0x31ef
+				VF610_PAD_PTA27__ESDHC1_DAT1	0x31ef
+				VF610_PAD_PTA28__ESDHC1_DATA2	0x31ef
+				VF610_PAD_PTA29__ESDHC1_DAT3	0x31ef
+				VF610_PAD_PTB20__GPIO_42	0x219d
+			>;
+		};
+
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+				VF610_PAD_PTC9__ENET_RMII1_MDC		0x30d2
+				VF610_PAD_PTC10__ENET_RMII1_MDIO	0x30d3
+				VF610_PAD_PTC11__ENET_RMII1_CRS		0x30d1
+				VF610_PAD_PTC12__ENET_RMII_RXD1		0x30d1
+				VF610_PAD_PTC13__ENET_RMII1_RXD0	0x30d1
+				VF610_PAD_PTC14__ENET_RMII1_RXER	0x30d1
+				VF610_PAD_PTC15__ENET_RMII1_TXD1	0x30d2
+				VF610_PAD_PTC16__ENET_RMII1_TXD0	0x30d2
+				VF610_PAD_PTC17__ENET_RMII1_TXEN	0x30d2
+			>;
+		};
+
+		pinctrl_uart0: uart0grp {
+			fsl,pins = <
+				VF610_PAD_PTB10__UART0_TX		0x21a2
+				VF610_PAD_PTB11__UART0_RX		0x21a1
+			>;
+		};
+
+		pinctrl_uart1: uart1grp {
+			fsl,pins = <
+				VF610_PAD_PTB4__UART1_TX		0x21a2
+				VF610_PAD_PTB5__UART1_RX		0x21a1
+			>;
+		};
+
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <
+				VF610_PAD_PTD0__UART2_TX		0x21a2
+				VF610_PAD_PTD1__UART2_RX		0x21a1
+				VF610_PAD_PTD2__UART2_RTS		0x21a2
+				VF610_PAD_PTD3__UART2_CTS		0x21a1
+			>;
+		};
+	};
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&fec1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	status = "okay";
+};
+
+&L2 {
+	arm,data-latency = <2 1 2>;
+	arm,tag-latency = <3 2 3>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
Signature · 1 line
1.9.1
#3 lore raw

PATCH 1/2 of: add vendor prefix for Toradex AG

In reply to stefan at agner.ch

Hi,

Quoted 14 lines · stefan at agner.ch

From: Stefan Agner <[email protected]>

Adds toradex to the list of DT vendor prefixes.

---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +0 -0
index e9d19e2..6a68eae 100644

Documentation/devicetree/bindings/vendor-prefixes.txt ti Texas Instruments · line 94

Quoted 4 lines
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
@@ -91,6 +91,7 @@ ti	Texas Instruments
 tlm	Trusted Logic Mobility
 toshiba	Toshiba Corporation
 toumaz	Toumaz
+toradex	Toradex AG

The alphabet seems to be a concept that is very hard to grasp for programmers... ;)
In my version 'r' is located before 's'.

Lothar Wa?mann

Signature · 9 lines
___________________________________________________________

Ka-Ro electronics GmbH | Pascalstra?e 22 | D - 52076 Aachen
Phone: +49 2408 1402-0 | Fax: +49 2408 1402-10
Gesch?ftsf?hrer: Matthias Kaussen
Handelsregistereintrag: Amtsgericht Aachen, HRB 4996

www.karo-electronics.de | info at karo-electronics.de
___________________________________________________________