Skip to contentSkip to conversation

drm/mxsfb: Fix runtime PM for unpowering lcdif block

PATCH In review Leonard Crestez 2 participants 9 messages Aug 8, 2018 – Aug 13, 2018

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v4 cover drm/mxsfb: Fix runtime PM for unpowering lcdif block

Adding lcdif nodes to a power domain currently does work, it results in black/corrupted screens or hangs. While the driver does enable runtime pm it does not deal correctly with the block being unpowered.

Changes since v3:
* Don't set initial fb in mode_set_nofb, do it in crtc_enable
* Simplify AXI clk handling to allow setting fb in crtc_enable
* No functional changes

Last 3 patches are identical to v3 with review tags attached.

Link to v3: https://lkml.org/lkml/2018/8/6/728

Leonard Crestez (5):
drm/mxsfb: Move axi clk enable/disable to crtc enable/disable drm/mxsfb: Fix initial corrupt frame when activating display drm/mxsfb: Add pm_runtime calls to pipe_enable/disable drm/mxsfb: Add PM_SLEEP support
drm/mxsfb: Switch to drm_atomic_helper_commit_tail_rpm

 drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 53 +++++++++++++++++++-----------
 drivers/gpu/drm/mxsfb/mxsfb_drv.c  | 40 ++++++++++++++++++++++
 2 files changed, 74 insertions(+), 19 deletions(-)
Signature · 1 line
2.17.1
#1 lore raw

PATCH v4 1/5 drm/mxsfb: Move axi clk enable/disable to crtc enable/disable

The main axi clk is disabled at the end of mxsfb_crtc_mode_set_nofb and immediately reenabled in mxsfb_enable_controller.

Avoid this by moving the handling of axi clk one level up to mxsfb_crtc_enable. Do the same for mxsfb_crtc_disable for simmetry

This shouldn't have any functional effect.

---
 drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
drivers/gpu/drm/mxsfb/mxsfb_crtc.c +2 -6
index 0abe77675b76..e4fcbb65b969 100644
@@ -127,11 +127,10 @@ static void mxsfb_enable_controller(struct mxsfb_drm_private *mxsfb)
 	u32 reg;
 
 	if (mxsfb->clk_disp_axi)
 		clk_prepare_enable(mxsfb->clk_disp_axi);
 	clk_prepare_enable(mxsfb->clk);
-	mxsfb_enable_axi_clk(mxsfb);
 
 	/* If it was disabled, re-enable the mode again */
 	writel(CTRL_DOTCLK_MODE, mxsfb->base + LCDC_CTRL + REG_SET);
 
 	/* Enable the SYNC signals first, then the DMA engine */
@@ -157,12 +156,10 @@ static void mxsfb_disable_controller(struct mxsfb_drm_private *mxsfb)
 
 	reg = readl(mxsfb->base + LCDC_VDCTRL4);
 	reg &= ~VDCTRL4_SYNC_SIGNALS_ON;
 	writel(reg, mxsfb->base + LCDC_VDCTRL4);
 
-	mxsfb_disable_axi_clk(mxsfb);
-
 	clk_disable_unprepare(mxsfb->clk);
 	if (mxsfb->clk_disp_axi)
 		clk_disable_unprepare(mxsfb->clk_disp_axi);
 }
 
@@ -206,11 +203,10 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
 	/*
 	 * It seems, you can't re-program the controller if it is still
 	 * running. This may lead to shifted pictures (FIFO issue?), so
 	 * first stop the controller and drain its FIFOs.
 	 */
-	mxsfb_enable_axi_clk(mxsfb);
 
 	/* Mandatory eLCDIF reset as per the Reference Manual */
 	err = mxsfb_reset_block(mxsfb->base);
 	if (err)
 		return;
@@ -267,23 +263,23 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
 	       SET_VERT_WAIT_CNT(m->crtc_vtotal - m->crtc_vsync_start),
 	       mxsfb->base + LCDC_VDCTRL3);
 
 	writel(SET_DOTCLK_H_VALID_DATA_CNT(m->hdisplay),
 	       mxsfb->base + LCDC_VDCTRL4);
-
-	mxsfb_disable_axi_clk(mxsfb);
 }
 
 void mxsfb_crtc_enable(struct mxsfb_drm_private *mxsfb)
 {
+	mxsfb_enable_axi_clk(mxsfb);
 	mxsfb_crtc_mode_set_nofb(mxsfb);
 	mxsfb_enable_controller(mxsfb);
 }
 
 void mxsfb_crtc_disable(struct mxsfb_drm_private *mxsfb)
 {
 	mxsfb_disable_controller(mxsfb);
+	mxsfb_disable_axi_clk(mxsfb);
 }
 
 void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
 			       struct drm_plane_state *state)
 {
Signature · 1 line
2.17.1
maintainer Reviewed-by on v4 1/5
#2 lore raw

Re: [PATCH v4 1/5] drm/mxsfb: Move axi clk enable/disable to crtc enable/disable

Quoted 9 lines · Leonard Crestez

The main axi clk is disabled at the end of mxsfb_crtc_mode_set_nofb and immediately reenabled in mxsfb_enable_controller.

Avoid this by moving the handling of axi clk one level up to mxsfb_crtc_enable. Do the same for mxsfb_crtc_disable for simmetry

This shouldn't have any functional effect.

Thanks, looks good!

Quoted 76 lines
---
 drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
drivers/gpu/drm/mxsfb/mxsfb_crtc.c +0 -1
index 0abe77675b76..e4fcbb65b969 100644
@@ -127,11 +127,10 @@ static void mxsfb_enable_controller(struct
 mxsfb_drm_private *mxsfb)
 	u32 reg;
 
 	if (mxsfb->clk_disp_axi)
 		clk_prepare_enable(mxsfb->clk_disp_axi);
 	clk_prepare_enable(mxsfb->clk);
-	mxsfb_enable_axi_clk(mxsfb);
 
 	/* If it was disabled, re-enable the mode again */
 	writel(CTRL_DOTCLK_MODE, mxsfb->base + LCDC_CTRL + REG_SET);
 
drivers/gpu/drm/mxsfb/mxsfb_crtc.c +0 -3
 	/* Enable the SYNC signals first, then the DMA engine */
@@ -157,12 +156,10 @@ static void mxsfb_disable_controller(struct
 mxsfb_drm_private *mxsfb)
 
 	reg = readl(mxsfb->base + LCDC_VDCTRL4);
 	reg &= ~VDCTRL4_SYNC_SIGNALS_ON;
 	writel(reg, mxsfb->base + LCDC_VDCTRL4);
 
-	mxsfb_disable_axi_clk(mxsfb);
-
 	clk_disable_unprepare(mxsfb->clk);
 	if (mxsfb->clk_disp_axi)
 		clk_disable_unprepare(mxsfb->clk_disp_axi);
 }
@@ -206,11 +203,10 @@ static void mxsfb_crtc_mode_set_nofb(struct
 mxsfb_drm_private *mxsfb)
 	/*
 	 * It seems, you can't re-program the controller if it is still
 	 * running. This may lead to shifted pictures (FIFO issue?), so
 	 * first stop the controller and drain its FIFOs.
 	 */
-	mxsfb_enable_axi_clk(mxsfb);
 
 	/* Mandatory eLCDIF reset as per the Reference Manual */
 	err = mxsfb_reset_block(mxsfb->base);
 	if (err)
drivers/gpu/drm/mxsfb/mxsfb_crtc.c +2 -2
 		return;
@@ -267,23 +263,23 @@ static void mxsfb_crtc_mode_set_nofb(struct
 mxsfb_drm_private *mxsfb)
 	       SET_VERT_WAIT_CNT(m->crtc_vtotal - m->crtc_vsync_start),
 	       mxsfb->base + LCDC_VDCTRL3);
 
 	writel(SET_DOTCLK_H_VALID_DATA_CNT(m->hdisplay),
 	       mxsfb->base + LCDC_VDCTRL4);
-
-	mxsfb_disable_axi_clk(mxsfb);
 }
 
 void mxsfb_crtc_enable(struct mxsfb_drm_private *mxsfb)
 {
+	mxsfb_enable_axi_clk(mxsfb);
 	mxsfb_crtc_mode_set_nofb(mxsfb);
 	mxsfb_enable_controller(mxsfb);
 }
 
 void mxsfb_crtc_disable(struct mxsfb_drm_private *mxsfb)
 {
 	mxsfb_disable_controller(mxsfb);
+	mxsfb_disable_axi_clk(mxsfb);
 }
 
 void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
 			       struct drm_plane_state *state)

{

#3 lore raw

Re: [PATCH v4 1/5] drm/mxsfb: Move axi clk enable/disable to crtc enable/disable

Quoted 7 lines · Stefan Agner
Quoted 6 lines · Leonard Crestez

The main axi clk is disabled at the end of mxsfb_crtc_mode_set_nofb and immediately reenabled in mxsfb_enable_controller.

Avoid this by moving the handling of axi clk one level up to mxsfb_crtc_enable. Do the same for mxsfb_crtc_disable for simmetry

Quoted 7 lines
Quoted 3 lines

This shouldn't have any functional effect.

Thanks, looks good!

So what is next now that this entire series was reviewed? My guess is that somebody needs to push it to drm-misc-next.

However 4.18 was just released and I'm not sure how this interacts with drm. As far as I can tell drm-misc-next is always open and a patch accepted now will make it into 4.20, based on this graph:

https://01.org/linuxgraphics/gfx-docs/maintainer-tools/drm-misc.html#merge-timeline

--
Regards,
Leonard

#4 lore raw

PATCH v4 2/5 drm/mxsfb: Fix initial corrupt frame when activating display

In reply to Leonard Crestez

LCDIF will repeatedly display data from CUR_BUF and set CUR_BUF to NEXT_BUF when done. Since we are only ever writing to NEXT_BUF the display will show an initial corrupt frame.

Fix by writing the FB paddr to both CUR_BUF and NEXT_BUF when activating the CRTC.

---
 drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 45 +++++++++++++++++++++---------
 1 file changed, 32 insertions(+), 13 deletions(-)
drivers/gpu/drm/mxsfb/mxsfb_crtc.c +32 -13
index e4fcbb65b969..24b1f0c1432e 100644
@@ -191,10 +191,25 @@ static int mxsfb_reset_block(void __iomem *reset_addr)
 		return ret;
 
 	return clear_poll_bit(reset_addr, MODULE_CLKGATE);
 }
 
+static dma_addr_t mxsfb_get_fb_paddr(struct mxsfb_drm_private *mxsfb)
+{
+	struct drm_framebuffer *fb = mxsfb->pipe.plane.state->fb;
+	struct drm_gem_cma_object *gem;
+
+	if (!fb)
+		return 0;
+
+	gem = drm_fb_cma_get_gem_obj(fb, 0);
+	if (!gem)
+		return 0;
+
+	return gem->paddr;
+}
+
 static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
 {
 	struct drm_display_mode *m = &mxsfb->pipe.crtc.state->adjusted_mode;
 	const u32 bus_flags = mxsfb->connector.display_info.bus_flags;
 	u32 vdctrl0, vsync_pulse_len, hsync_pulse_len;
@@ -267,12 +282,22 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
 	       mxsfb->base + LCDC_VDCTRL4);
 }
 
 void mxsfb_crtc_enable(struct mxsfb_drm_private *mxsfb)
 {
+	dma_addr_t paddr;
+
 	mxsfb_enable_axi_clk(mxsfb);
 	mxsfb_crtc_mode_set_nofb(mxsfb);
+
+	/* Write cur_buf as well to avoid an initial corrupt frame */
+	paddr = mxsfb_get_fb_paddr(mxsfb);
+	if (paddr) {
+		writel(paddr, mxsfb->base + mxsfb->devdata->cur_buf);
+		writel(paddr, mxsfb->base + mxsfb->devdata->next_buf);
+	}
+
 	mxsfb_enable_controller(mxsfb);
 }
 
 void mxsfb_crtc_disable(struct mxsfb_drm_private *mxsfb)
 {
@@ -283,16 +308,12 @@ void mxsfb_crtc_disable(struct mxsfb_drm_private *mxsfb)
 void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
 			       struct drm_plane_state *state)
 {
 	struct drm_simple_display_pipe *pipe = &mxsfb->pipe;
 	struct drm_crtc *crtc = &pipe->crtc;
-	struct drm_framebuffer *fb = pipe->plane.state->fb;
 	struct drm_pending_vblank_event *event;
-	struct drm_gem_cma_object *gem;
-
-	if (!crtc)
-		return;
+	dma_addr_t paddr;
 
 	spin_lock_irq(&crtc->dev->event_lock);
 	event = crtc->state->event;
 	if (event) {
 		crtc->state->event = NULL;
@@ -303,14 +324,12 @@ void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
 			drm_crtc_send_vblank_event(crtc, event);
 		}
 	}
 	spin_unlock_irq(&crtc->dev->event_lock);
 
-	if (!fb)
-		return;
-
-	gem = drm_fb_cma_get_gem_obj(fb, 0);
-
-	mxsfb_enable_axi_clk(mxsfb);
-	writel(gem->paddr, mxsfb->base + mxsfb->devdata->next_buf);
-	mxsfb_disable_axi_clk(mxsfb);
+	paddr = mxsfb_get_fb_paddr(mxsfb);
+	if (paddr) {
+		mxsfb_enable_axi_clk(mxsfb);
+		writel(paddr, mxsfb->base + mxsfb->devdata->next_buf);
+		mxsfb_disable_axi_clk(mxsfb);
+	}
 }
Signature · 1 line
2.17.1
maintainer Reviewed-by on v4 2/5
#5 lore raw

Re: [PATCH v4 2/5] drm/mxsfb: Fix initial corrupt frame when activating display

Quoted 9 lines · Leonard Crestez

LCDIF will repeatedly display data from CUR_BUF and set CUR_BUF to NEXT_BUF when done. Since we are only ever writing to NEXT_BUF the display will show an initial corrupt frame.

Fix by writing the FB paddr to both CUR_BUF and NEXT_BUF when activating the CRTC.

Quoted 98 lines
---
 drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 45 +++++++++++++++++++++---------
 1 file changed, 32 insertions(+), 13 deletions(-)
drivers/gpu/drm/mxsfb/mxsfb_crtc.c +25 -0
index e4fcbb65b969..24b1f0c1432e 100644
@@ -191,10 +191,25 @@ static int mxsfb_reset_block(void __iomem *reset_addr)
 		return ret;
 
 	return clear_poll_bit(reset_addr, MODULE_CLKGATE);
 }
 
+static dma_addr_t mxsfb_get_fb_paddr(struct mxsfb_drm_private *mxsfb)
+{
+	struct drm_framebuffer *fb = mxsfb->pipe.plane.state->fb;
+	struct drm_gem_cma_object *gem;
+
+	if (!fb)
+		return 0;
+
+	gem = drm_fb_cma_get_gem_obj(fb, 0);
+	if (!gem)
+		return 0;
+
+	return gem->paddr;
+}
+
 static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
 {
 	struct drm_display_mode *m = &mxsfb->pipe.crtc.state->adjusted_mode;
 	const u32 bus_flags = mxsfb->connector.display_info.bus_flags;
 	u32 vdctrl0, vsync_pulse_len, hsync_pulse_len;
@@ -267,12 +282,22 @@ static void mxsfb_crtc_mode_set_nofb(struct
 mxsfb_drm_private *mxsfb)
 	       mxsfb->base + LCDC_VDCTRL4);
 }
 
 void mxsfb_crtc_enable(struct mxsfb_drm_private *mxsfb)
 {
+	dma_addr_t paddr;
+
 	mxsfb_enable_axi_clk(mxsfb);
 	mxsfb_crtc_mode_set_nofb(mxsfb);
+
+	/* Write cur_buf as well to avoid an initial corrupt frame */
+	paddr = mxsfb_get_fb_paddr(mxsfb);
+	if (paddr) {
+		writel(paddr, mxsfb->base + mxsfb->devdata->cur_buf);
+		writel(paddr, mxsfb->base + mxsfb->devdata->next_buf);
+	}
+
 	mxsfb_enable_controller(mxsfb);
 }
 
 void mxsfb_crtc_disable(struct mxsfb_drm_private *mxsfb)

{

drivers/gpu/drm/mxsfb/mxsfb_crtc.c +7 -13
@@ -283,16 +308,12 @@ void mxsfb_crtc_disable(struct mxsfb_drm_private *mxsfb)
 void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
 			       struct drm_plane_state *state)
 {
 	struct drm_simple_display_pipe *pipe = &mxsfb->pipe;
 	struct drm_crtc *crtc = &pipe->crtc;
-	struct drm_framebuffer *fb = pipe->plane.state->fb;
 	struct drm_pending_vblank_event *event;
-	struct drm_gem_cma_object *gem;
-
-	if (!crtc)
-		return;
+	dma_addr_t paddr;
 
 	spin_lock_irq(&crtc->dev->event_lock);
 	event = crtc->state->event;
 	if (event) {
 		crtc->state->event = NULL;
@@ -303,14 +324,12 @@ void mxsfb_plane_atomic_update(struct
 mxsfb_drm_private *mxsfb,
 			drm_crtc_send_vblank_event(crtc, event);
 		}
 	}
 	spin_unlock_irq(&crtc->dev->event_lock);
 
-	if (!fb)
-		return;
-
-	gem = drm_fb_cma_get_gem_obj(fb, 0);
-
-	mxsfb_enable_axi_clk(mxsfb);
-	writel(gem->paddr, mxsfb->base + mxsfb->devdata->next_buf);
-	mxsfb_disable_axi_clk(mxsfb);
+	paddr = mxsfb_get_fb_paddr(mxsfb);
+	if (paddr) {
+		mxsfb_enable_axi_clk(mxsfb);
+		writel(paddr, mxsfb->base + mxsfb->devdata->next_buf);
+		mxsfb_disable_axi_clk(mxsfb);
+	}
Quoted 1 line

}

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#6 lore raw

PATCH v4 3/5 drm/mxsfb: Add pm_runtime calls to pipe_enable/disable

In reply to Leonard Crestez

Adding lcdif nodes to a power domain currently results in black/corrupted screens or hangs because power is not correctly enabled when required.

Ensure power is on when display is active by adding pm_runtime_get/put_sync to mxsfb_pipe_enable/disable.

---
 drivers/gpu/drm/mxsfb/mxsfb_drv.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/gpu/drm/mxsfb/mxsfb_drv.c +4 -0
index ffe5137ccaf8..68d79f5dc0d3 100644
@@ -101,23 +101,27 @@ static const struct drm_mode_config_funcs mxsfb_mode_config_funcs = {
 static void mxsfb_pipe_enable(struct drm_simple_display_pipe *pipe,
 			      struct drm_crtc_state *crtc_state,
 			      struct drm_plane_state *plane_state)
 {
 	struct mxsfb_drm_private *mxsfb = drm_pipe_to_mxsfb_drm_private(pipe);
+	struct drm_device *drm = pipe->plane.dev;
 
+	pm_runtime_get_sync(drm->dev);
 	drm_panel_prepare(mxsfb->panel);
 	mxsfb_crtc_enable(mxsfb);
 	drm_panel_enable(mxsfb->panel);
 }
 
 static void mxsfb_pipe_disable(struct drm_simple_display_pipe *pipe)
 {
 	struct mxsfb_drm_private *mxsfb = drm_pipe_to_mxsfb_drm_private(pipe);
+	struct drm_device *drm = pipe->plane.dev;
 
 	drm_panel_disable(mxsfb->panel);
 	mxsfb_crtc_disable(mxsfb);
 	drm_panel_unprepare(mxsfb->panel);
+	pm_runtime_put_sync(drm->dev);
 }
 
 static void mxsfb_pipe_update(struct drm_simple_display_pipe *pipe,
 			      struct drm_plane_state *plane_state)
 {
Signature · 1 line
2.17.1
#7 lore raw

PATCH v4 4/5 drm/mxsfb: Add PM_SLEEP support

In reply to Leonard Crestez

Since power to the lcdif block can be lost on suspend implement PM_SLEEP_OPS using drm_mode_config_helper_suspend/resume to save/restore the current mode.

---
 drivers/gpu/drm/mxsfb/mxsfb_drv.c | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
drivers/gpu/drm/mxsfb/mxsfb_drv.c +21 -0
index 68d79f5dc0d3..d797dfd40d98 100644
@@ -416,17 +416,38 @@ static int mxsfb_remove(struct platform_device *pdev)
 	drm_dev_unref(drm);
 
 	return 0;
 }
 
+#ifdef CONFIG_PM_SLEEP
+static int mxsfb_suspend(struct device *dev)
+{
+       struct drm_device *drm = dev_get_drvdata(dev);
+
+       return drm_mode_config_helper_suspend(drm);
+}
+
+static int mxsfb_resume(struct device *dev)
+{
+       struct drm_device *drm = dev_get_drvdata(dev);
+
+       return drm_mode_config_helper_resume(drm);
+}
+#endif
+
+static const struct dev_pm_ops mxsfb_pm_ops = {
+       SET_SYSTEM_SLEEP_PM_OPS(mxsfb_suspend, mxsfb_resume)
+};
+
 static struct platform_driver mxsfb_platform_driver = {
 	.probe		= mxsfb_probe,
 	.remove		= mxsfb_remove,
 	.id_table	= mxsfb_devtype,
 	.driver	= {
 		.name		= "mxsfb",
 		.of_match_table	= mxsfb_dt_ids,
+		.pm		= &mxsfb_pm_ops,
 	},
 };
 
 module_platform_driver(mxsfb_platform_driver);
 
Signature · 1 line
2.17.1
#8 lore raw

PATCH v4 5/5 drm/mxsfb: Switch to drm_atomic_helper_commit_tail_rpm

In reply to Leonard Crestez

The lcdif block is only powered on when display is active so plane updates when not enabled are not valid. Writing to an unpowered IP block is mostly ignored but can trigger bus errors on some chips.

Prevent this situation by switching to drm_atomic_helper_commit_tail_rpm and having the drm core ensure atomic_plane_update is only called while the crtc is active. This avoids having to keep track of "enabled" bits inside the mxsfb driver.

This also requires handling the vblank event for disable from mxsfb_pipe_update.

---
 drivers/gpu/drm/mxsfb/mxsfb_drv.c | 15 +++++++++++++++
 1 file changed, 15 insertions(+)
drivers/gpu/drm/mxsfb/mxsfb_drv.c +15 -0
index d797dfd40d98..5777e730085b 100644
@@ -96,10 +96,14 @@ static const struct drm_mode_config_funcs mxsfb_mode_config_funcs = {
 	.fb_create		= drm_gem_fb_create,
 	.atomic_check		= drm_atomic_helper_check,
 	.atomic_commit		= drm_atomic_helper_commit,
 };
 
+static const struct drm_mode_config_helper_funcs mxsfb_mode_config_helpers = {
+	.atomic_commit_tail = drm_atomic_helper_commit_tail_rpm,
+};
+
 static void mxsfb_pipe_enable(struct drm_simple_display_pipe *pipe,
 			      struct drm_crtc_state *crtc_state,
 			      struct drm_plane_state *plane_state)
 {
 	struct mxsfb_drm_private *mxsfb = drm_pipe_to_mxsfb_drm_private(pipe);
@@ -113,15 +117,25 @@ static void mxsfb_pipe_enable(struct drm_simple_display_pipe *pipe,
 
 static void mxsfb_pipe_disable(struct drm_simple_display_pipe *pipe)
 {
 	struct mxsfb_drm_private *mxsfb = drm_pipe_to_mxsfb_drm_private(pipe);
 	struct drm_device *drm = pipe->plane.dev;
+	struct drm_crtc *crtc = &pipe->crtc;
+	struct drm_pending_vblank_event *event;
 
 	drm_panel_disable(mxsfb->panel);
 	mxsfb_crtc_disable(mxsfb);
 	drm_panel_unprepare(mxsfb->panel);
 	pm_runtime_put_sync(drm->dev);
+
+	spin_lock_irq(&drm->event_lock);
+	event = crtc->state->event;
+	if (event) {
+		crtc->state->event = NULL;
+		drm_crtc_send_vblank_event(crtc, event);
+	}
+	spin_unlock_irq(&drm->event_lock);
 }
 
 static void mxsfb_pipe_update(struct drm_simple_display_pipe *pipe,
 			      struct drm_plane_state *plane_state)
 {
@@ -232,10 +246,11 @@ static int mxsfb_load(struct drm_device *drm, unsigned long flags)
 	drm->mode_config.min_width	= MXSFB_MIN_XRES;
 	drm->mode_config.min_height	= MXSFB_MIN_YRES;
 	drm->mode_config.max_width	= MXSFB_MAX_XRES;
 	drm->mode_config.max_height	= MXSFB_MAX_YRES;
 	drm->mode_config.funcs		= &mxsfb_mode_config_funcs;
+	drm->mode_config.helper_private	= &mxsfb_mode_config_helpers;
 
 	drm_mode_config_reset(drm);
 
 	pm_runtime_get_sync(drm->dev);
 	ret = drm_irq_install(drm, platform_get_irq(pdev, 0));
Signature · 1 line
2.17.1