arm: mvebu: clearfog: support boot from SATA disk
Subsystems (3)
cover arm: mvebu: clearfog: support boot from SATA disk
This series enables support for boot from SATA on the SolidRun Clearfog platform.
Patches 1-3 are preparations for the addition of loading U-Boot main image from raw SATA device. They make spl sata code independent of board macros and specific kconfig symbols.
Patch 4 adds to SPL generic support for loading U-Boot from a raw SATA device. This code is modeled after the similar support for MMC devices.
Patches 5-6 are mvebu specific. Patch 5 fixes SATA access from SPL. Patch 6 adds the SATA boot option at the SoC level.
Patches 7-9 are the board specific update that enable SATA boot in Clearfog, and document the offset setting requirement.
Baruch Siach (9):
spl: sata: add default partition and image name
spl: sata: fix build with DM_SCSI
spl: sata: don't force FS_FAT support
spl: sata: support U-Boot load from raw sata disk
arm: mvebu: fix ahci mbus config in SPL
arm: mvebu: add support for boot from SATA
arm: mvebu: clearfog: enable SATA in SPL
arm: mvebu: clearfog: set U-Boot offset for SATA boot
arm: mvebu: clearfog: document boot from SATA
arch/arm/dts/armada-388-clearfog-u-boot.dtsi | 8 ++++ arch/arm/mach-mvebu/Kconfig | 5 ++ arch/arm/mach-mvebu/Makefile | 3 ++ arch/arm/mach-mvebu/cpu.c | 4 ++ arch/arm/mach-mvebu/include/mach/soc.h | 2 + arch/arm/mach-mvebu/spl.c | 5 ++ board/solidrun/clearfog/README | 6 +++ common/spl/Kconfig | 14 ++++++ common/spl/spl_sata.c | 49 ++++++++++++++++++-- include/configs/clearfog.h | 2 +- 10 files changed, 94 insertions(+), 4 deletions(-)
Signature · 1 line
2.20.1
PATCH 1/9 spl: sata: add default partition and image name
Add sensible defaults for the FAT partition selection and the main U-Boot image file name. This allows spl_sata to build when the board headers does not select them explicitly.
--- common/spl/spl_sata.c | 8 ++++++++ 1 file changed, 8 insertions(+)
common/spl/spl_sata.c +8 -0
@@ -17,6 +17,14 @@#include <fat.h> #include <image.h> +#ifndef CONFIG_SYS_SATA_FAT_BOOT_PARTITION +#define CONFIG_SYS_SATA_FAT_BOOT_PARTITION 1 +#endif + +#ifndef CONFIG_SPL_FS_LOAD_PAYLOAD_NAME +#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" +#endif +static int spl_sata_load_image (struct spl_image_info *spl_image,struct spl_boot_device *bootdev) {
Signature · 1 line
2.20.1
PATCH 2/9 spl: sata: fix build with DM_SCSI
In reply to Baruch SiachThe init_sata() routine is only present when DM_SCSI is not enabled. Don't call init_sata() when DM_SCSI is enabled. The code will fall back to scsi_scan() in this case.
--- common/spl/spl_sata.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
common/spl/spl_sata.c +3 -1
@@ -28,10 +28,12 @@static int spl_sata_load_image (struct spl_image_info *spl_image,struct spl_boot_device *bootdev) { -int err; +int err =0 ;struct blk_desc *stor_dev; +#if !defined(CONFIG_DM_SCSI ) && !defined(CONFIG_AHCI ) err =init_sata (CONFIG_SPL_SATA_BOOT_DEVICE ); +#endif if (err) {#ifdef CONFIG_SPL_LIBCOMMON_SUPPORT printf ("spl: sata init failed: err - %d\n" , err);
Signature · 1 line
2.20.1
PATCH 3/9 spl: sata: don't force FS_FAT support
In reply to Baruch SiachAllow the code to build when FS_FAT is not enabled, and thus spl_load_image_fat() is not provided.
A subsequent patch should add alternative raw access U-Boot main image load method.
--- common/spl/spl_sata.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
common/spl/spl_sata.c +6 -2
@@ -53,9 +53,13 @@ static int spl_sata_load_image(struct spl_image_info *spl_image, CONFIG_SYS_SATA_FAT_BOOT_PARTITION))#endif { - err =spl_load_image_fat (spl_image, stor_dev, + err = -ENOSYS ; + +if (IS_ENABLED (CONFIG_SPL_FS_FAT )) { + err =spl_load_image_fat (spl_image, stor_dev,CONFIG_SYS_SATA_FAT_BOOT_PARTITION , -CONFIG_SPL_FS_LOAD_PAYLOAD_NAME ); +CONFIG_SPL_FS_LOAD_PAYLOAD_NAME ); + } }if (err) {puts ("Error loading sata device\n" );
Signature · 1 line
2.20.1
PATCH 4/9 spl: sata: support U-Boot load from raw sata disk
In reply to Baruch SiachSupport load of the U-Boot image from raw SATA disk sector. This is equivalent to load from MMC raw sector.
--- common/spl/Kconfig | 14 ++++++++++++++ common/spl/spl_sata.c | 29 +++++++++++++++++++++++++++++ 2 files changed, 43 insertions(+)
common/spl/Kconfig +14 -0
@@ -733,6 +733,20 @@ config SPL_SATA_SUPPORT expense and power consumption. This enables loading from SATA using a configured device. +config SPL_SATA_RAW_U_BOOT_USE_SECTOR + bool "SATA raw mode: by sector" + depends on SPL_SATA_SUPPORT + help + Use sector number for specifying U-Boot location on SATA disk in + raw mode. + +config SPL_SATA_RAW_U_BOOT_SECTOR + hex "Sector on the SATA disk to load U-Boot from" + depends on SPL_SATA_RAW_U_BOOT_USE_SECTOR + help + Sector on the SATA disk to load U-Boot from, when the SATA disk is being + used in raw mode. Units: SATA disk sectors (1 sector = 512 bytes). + config SPL_SERIAL_SUPPORT bool "Support serial" select SPL_PRINTF
common/spl/spl_sata.c +29 -0
@@ -25,6 +25,32 @@#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"#endif +static int spl_sata_load_image_raw (struct spl_image_info *spl_image, +struct blk_desc *stor_dev,unsigned long sector) +{ +struct image_header *header; +unsigned long count; +u32 image_size_sectors; +int ret; + + header =spl_get_load_buffer (-sizeof (*header), stor_dev->blksz); + count =blk_dread (stor_dev, sector,1 , header); +if (count ==0 ) +return -EIO ; + + ret =spl_parse_image_header (spl_image, header); +if (ret) +return ret; + + image_size_sectors =DIV_ROUND_UP (spl_image->size, stor_dev->blksz); + count =blk_dread (stor_dev, sector, image_size_sectors, + (void *)spl_image->load_addr); +if (count != image_size_sectors) +return -EIO ; + +return 0 ; +} +static int spl_sata_load_image (struct spl_image_info *spl_image,struct spl_boot_device *bootdev) {
@@ -59,6 +85,9 @@ static int spl_sata_load_image(struct spl_image_info *spl_image, err =spl_load_image_fat (spl_image, stor_dev,CONFIG_SYS_SATA_FAT_BOOT_PARTITION ,CONFIG_SPL_FS_LOAD_PAYLOAD_NAME ); + }else if (IS_ENABLED (CONFIG_SPL_SATA_RAW_U_BOOT_USE_SECTOR )) { + err =spl_sata_load_image_raw (spl_image, stor_dev, +CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR ); } }if (err) {
Signature · 1 line
2.20.1
PATCH 5/9 arm: mvebu: fix ahci mbus config in SPL
In reply to Baruch SiachSPL does not initialize mbus_dram_info. Don't change the ahci mbus settings of the ROM. This allows the ahci to work in SPL.
--- arch/arm/mach-mvebu/cpu.c | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm/mach-mvebu/cpu.c +4 -0
@@ -542,6 +542,10 @@ static void ahci_mvebu_mbus_config(void __iomem *base)const struct mbus_dram_target_info *dram;int i; +/* mbus is not initialized in SPL; keep the ROM settings */ +if (IS_ENABLED (CONFIG_SPL_BUILD )) +return ; + dram =mvebu_mbus_dram_info ();for (i =0 ; i <4 ; i++) {
Signature · 1 line
2.20.1
PATCH 6/9 arm: mvebu: add support for boot from SATA
In reply to Baruch SiachAdd the required Kconfig and macro definitions to allow boot from SATA on Armada 38x systems.
--- arch/arm/mach-mvebu/Kconfig | 5 +++++ arch/arm/mach-mvebu/Makefile | 3 +++ arch/arm/mach-mvebu/include/mach/soc.h | 2 ++ arch/arm/mach-mvebu/spl.c | 5 +++++ 4 files changed, 15 insertions(+)
arch/arm/mach-mvebu/Kconfig +5 -0
@@ -239,6 +239,11 @@ config MVEBU_SPL_BOOT_DEVICE_MMC bool "SDIO/MMC card" select SPL_LIBDISK_SUPPORT +config MVEBU_SPL_BOOT_DEVICE_SATA + bool "SATA" + select SPL_SATA_SUPPORT + select SPL_LIBDISK_SUPPORT + config MVEBU_SPL_BOOT_DEVICE_UART bool "UART"
arch/arm/mach-mvebu/Makefile +3 -0
@@ -37,6 +37,9 @@ endif ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC),) KWB_CFG_BOOT_FROM=sdio endif +ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_SATA),) + KWB_CFG_BOOT_FROM=sata +endif ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_UART),) KWB_CFG_BOOT_FROM=uart endif
arch/arm/mach-mvebu/include/mach/soc.h +2 -0
@@ -159,7 +159,9 @@#define BOOT_DEV_SEL_MASK (0x3f << BOOT_DEV_SEL_OFFS)#define BOOT_FROM_NAND 0x0A +#define BOOT_FROM_SATA 0x22#define BOOT_FROM_UART 0x28 +#define BOOT_FROM_SATA_ALT 0x2A#define BOOT_FROM_UART_ALT 0x3f#define BOOT_FROM_SPI 0x32#define BOOT_FROM_MMC 0x30
arch/arm/mach-mvebu/spl.c +5 -0
@@ -59,6 +59,11 @@ static u32 get_boot_device(void)case BOOT_FROM_UART_ALT :#endif return BOOT_DEVICE_UART ; +#ifdef BOOT_FROM_SATA +case BOOT_FROM_SATA : +case BOOT_FROM_SATA_ALT : +return BOOT_DEVICE_SATA ; +#endif case BOOT_FROM_SPI :default :return BOOT_DEVICE_SPI ;
Signature · 1 line
2.20.1
PATCH 7/9 arm: mvebu: clearfog: enable SATA in SPL
In reply to Baruch SiachEnable SATA peripherals in SPL to allow boot from SATA.
--- arch/arm/dts/armada-388-clearfog-u-boot.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/arm/dts/armada-388-clearfog-u-boot.dtsi +8 -0
@@ -11,3 +11,11 @@ &sdhci { u-boot,dm-spl; }; + +&ahci0 { + u-boot,dm-spl; +}; + +&ahci1 { + u-boot,dm-spl; +};
Signature · 1 line
2.20.1
PATCH 8/9 arm: mvebu: clearfog: set U-Boot offset for SATA boot
In reply to Baruch SiachSee the offset of U-Boot in raw SATA disk to the same value as the MMC offset. That is 0x140 sectors from the beginning of the SPL, which is 0x141 sectors from the beginning of the device (after the MBR sector).
--- include/configs/clearfog.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
include/configs/clearfog.h +1 -1
@@ -85,7 +85,7 @@/* SPL related SPI defines */ #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS -#elif defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC ) +#elif defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC ) || defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SATA )/* SPL related MMC defines */ #define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10)#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS
Signature · 1 line
2.20.1
PATCH 9/9 arm: mvebu: clearfog: document boot from SATA
In reply to Baruch SiachDocument the main U-Boot image offset when booting from SATA disk on the Clearfog board.
--- board/solidrun/clearfog/README | 6 ++++++ 1 file changed, 6 insertions(+)
board/solidrun/clearfog/README +6 -0
@@ -40,6 +40,12 @@ Install U-Boot on eMMC boot partition from Linux running on Clearfog: Note that the SD card is not accessible when the Clearfog SOM has eMMC. Consider initial boot from UART (see below). +Install U-Boot on SATA: +----------------------- + +When loading the main U-Boot image from raw SATA sector, set +CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR to 0x141. + Boot selection: ---------------
Signature · 1 line
2.20.1
PATCH 5/9 arm: mvebu: fix ahci mbus config in SPL
In reply to Baruch SiachQuoted 5 lines · Baruch Siach
SPL does not initialize
mbus_dram_info. Don't change the ahci mbus settings of the ROM. This allows the ahci to work in SPL.Signed-off-by Baruch Siach <[email protected]>
Quoted 26 lines
--- arch/arm/mach-mvebu/cpu.c | 4 ++++ 1 file changed, 4 insertions(+)arch/arm/mach-mvebu/cpu.c +4
-1@@ -542,6 +542,10 @@ static void ahci_mvebu_mbus_config(void __iomem *base)const struct mbus_dram_target_info *dram;int i; +/* mbus is not initialized in SPL; keep the ROM settings */ +if (IS_ENABLED (CONFIG_SPL_BUILD )) +return ; + dram =mvebu_mbus_dram_info ();for (i =0 ; i <4 ; i++) { --2.20.1
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH 6/9 arm: mvebu: add support for boot from SATA
In reply to Baruch SiachQuoted 5 lines · Baruch Siach
Add the required
Kconfigand macro definitions to allow boot from SATA on Armada 38x systems.Signed-off-by Baruch Siach <[email protected]>
Quoted 74 lines
--- arch/arm/mach-mvebu/Kconfig | 5 +++++ arch/arm/mach-mvebu/Makefile | 3 +++ arch/arm/mach-mvebu/include/mach/soc.h | 2 ++ arch/arm/mach-mvebu/spl.c | 5 +++++ 4 files changed, 15 insertions(+)arch/arm/mach-mvebu/Kconfig +5
-0@@ -239,6 +239,11 @@ config MVEBU_SPL_BOOT_DEVICE_MMC bool "SDIO/MMC card" select SPL_LIBDISK_SUPPORT +config MVEBU_SPL_BOOT_DEVICE_SATA + bool "SATA" + select SPL_SATA_SUPPORT + select SPL_LIBDISK_SUPPORT + config MVEBU_SPL_BOOT_DEVICE_UART bool "UART"arch/arm/mach-mvebu/Makefile +3
-0@@ -37,6 +37,9 @@ endif ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC),) KWB_CFG_BOOT_FROM=sdio endif +ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_SATA),) + KWB_CFG_BOOT_FROM=sata +endif ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_UART),) KWB_CFG_BOOT_FROM=uart endifarch/arm/mach-mvebu/include/mach/soc.h +2
-0@@ -159,7 +159,9 @@#define BOOT_DEV_SEL_MASK (0x3f << BOOT_DEV_SEL_OFFS)#define BOOT_FROM_NAND 0x0A +#define BOOT_FROM_SATA 0x22#define BOOT_FROM_UART 0x28 +#define BOOT_FROM_SATA_ALT 0x2A#define BOOT_FROM_UART_ALT 0x3f#define BOOT_FROM_SPI 0x32#define BOOT_FROM_MMC 0x30arch/arm/mach-mvebu/spl.c +5
-1@@ -59,6 +59,11 @@ static u32 get_boot_device(void)case BOOT_FROM_UART_ALT :#endif return BOOT_DEVICE_UART ; +#ifdef BOOT_FROM_SATA +case BOOT_FROM_SATA : +case BOOT_FROM_SATA_ALT : +return BOOT_DEVICE_SATA ; +#endif case BOOT_FROM_SPI :default :return BOOT_DEVICE_SPI ; --2.20.1
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH 7/9 arm: mvebu: clearfog: enable SATA in SPL
In reply to Baruch SiachQuoted 4 lines · Baruch Siach
Enable SATA peripherals in SPL to allow boot from SATA.
Signed-off-by Baruch Siach <[email protected]>
Quoted 27 lines
--- arch/arm/dts/armada-388-clearfog-u-boot.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+)arch/arm/dts/armada-388-clearfog-u-boot.dtsi +8
-1@@ -11,3 +11,11 @@ &sdhci { u-boot,dm-spl; }; + +&ahci0 { + u-boot,dm-spl; +}; + +&ahci1 { + u-boot,dm-spl; +}; --2.20.1
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH 8/9 arm: mvebu: clearfog: set U-Boot offset for SATA boot
In reply to Baruch SiachQuoted 2 lines · Baruch Siach
See the offset of U-Boot in raw SATA disk to the same value as the MMC
s/See/Set/
Quoted 4 lines
offset. That is
0x140sectors from the beginning of the SPL, which is0x141sectors from the beginning of the device (after the MBR sector).Signed-off-by Baruch Siach <[email protected]>
With the typo fix above
Quoted 24 lines
--- include/configs/clearfog.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)include/configs/clearfog.h +1
-2@@ -85,7 +85,7 @@/* SPL related SPI defines */ #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS -#elif defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC ) +#elif defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC ) || defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SATA )/* SPL related MMC defines */ #define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10)#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS --2.20.1
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH 9/9 arm: mvebu: clearfog: document boot from SATA
In reply to Baruch SiachQuoted 5 lines · Baruch Siach
Document the main U-Boot image offset when booting from SATA disk on the Clearfog board.
Signed-off-by Baruch Siach <[email protected]>
Quoted 28 lines
--- board/solidrun/clearfog/README | 6 ++++++ 1 file changed, 6 insertions(+)board/solidrun/clearfog/README +6
-1@@ -40,6 +40,12 @@ Install U-Boot on eMMC boot partition from Linux running on Clearfog: Note that the SD card is not accessible when the Clearfog SOM has eMMC. Consider initial boot from UART (see below). +Install U-Boot on SATA: +----------------------- + +When loading the main U-Boot image from raw SATA sector, set +CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR to 0x141. + Boot selection: --------------- --2.20.1
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH 4/9 spl: sata: support U-Boot load from raw sata disk
In reply to Baruch SiachHi Baruch,
Quoted 4 lines · Baruch Siach
Support load of the U-Boot image from raw SATA disk sector. This is equivalent to load from MMC raw sector.
Signed-off-by Baruch Siach <[email protected]>
This patch breaks cm_t54:
$ ./tools/buildman/buildman cm_t54
Building current source for 1 boards (1 thread, 16 jobs per thread)
arm: + cm_t54
+common/spl/spl_sata.c: In function ?spl_sata_load_image?:
+common/spl/spl_sata.c:90:5: error: ?CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR? undeclared (first use in this function); did you mean ?CONFIG_SPL_SATA_BOOT_DEVICE??
+ CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR);
+ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CONFIG_SPL_SATA_BOOT_DEVICE
+common/spl/spl_sata.c:90:5: note: each undeclared identifier is reported only once for each function it appears in
+make[3]: *** [scripts/Makefile.build:278: spl/common/spl/spl_sata.o] Error 1
+make[2]: *** [scripts/Makefile.spl:410: spl/common/spl] Error 2
+make[1]: *** [Makefile:1727: spl/u-boot-spl] Error 2
+make: *** [Makefile:148: sub-make] Error 2
0 0 1 /1 cm_t54I'm dropping this one from the upcoming pull request. Please re-send it, once you've fixed it. And please compile test it for all targets (Travis).
Thanks,
Stefan
Quoted 69 lines
--- common/spl/Kconfig | 14 ++++++++++++++ common/spl/spl_sata.c | 29 +++++++++++++++++++++++++++++ 2 files changed, 43 insertions(+)common/spl/Kconfig +14
-0@@ -733,6 +733,20 @@ config SPL_SATA_SUPPORT expense and power consumption. This enables loading from SATA using a configured device. +config SPL_SATA_RAW_U_BOOT_USE_SECTOR + bool "SATA raw mode: by sector" + depends on SPL_SATA_SUPPORT + help + Use sector number for specifying U-Boot location on SATA disk in + raw mode. + +config SPL_SATA_RAW_U_BOOT_SECTOR + hex "Sector on the SATA disk to load U-Boot from" + depends on SPL_SATA_RAW_U_BOOT_USE_SECTOR + help + Sector on the SATA disk to load U-Boot from, when the SATA disk is being + used in raw mode. Units: SATA disk sectors (1 sector = 512 bytes). + config SPL_SERIAL_SUPPORT bool "Support serial" select SPL_PRINTFcommon/spl/spl_sata.c +26
-0@@ -25,6 +25,32 @@#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"#endif +static int spl_sata_load_image_raw (struct spl_image_info *spl_image, +struct blk_desc *stor_dev,unsigned long sector) +{ +struct image_header *header; +unsigned long count; +u32 image_size_sectors; +int ret; + + header =spl_get_load_buffer (-sizeof (*header), stor_dev->blksz); + count =blk_dread (stor_dev, sector,1 , header); +if (count ==0 ) +return -EIO ; + + ret =spl_parse_image_header (spl_image, header); +if (ret) +return ret; + + image_size_sectors =DIV_ROUND_UP (spl_image->size, stor_dev->blksz); + count =blk_dread (stor_dev, sector, image_size_sectors, + (void *)spl_image->load_addr); +if (count != image_size_sectors) +return -EIO ; + +return 0 ; +} +static int spl_sata_load_image (struct spl_image_info *spl_image,struct spl_boot_device *bootdev) {
common/spl/spl_sata.c static int spl_sata_load_image(struct spl_image_info *spl_image, · line 93
Quoted 9 lines
common/spl/spl_sata.c +3
-0@@ -59,6 +85,9 @@ static int spl_sata_load_image(struct spl_image_info *spl_image, err =spl_load_image_fat (spl_image, stor_dev,CONFIG_SYS_SATA_FAT_BOOT_PARTITION ,CONFIG_SPL_FS_LOAD_PAYLOAD_NAME ); + }else if (IS_ENABLED (CONFIG_SPL_SATA_RAW_U_BOOT_USE_SECTOR )) { + err =spl_sata_load_image_raw (spl_image, stor_dev, +CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR ); } }if (err) {
Viele Grüße,
Stefan
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de