Skip to contentSkip to conversation

Add CMU/RMU/DMA support for Actions Semi S500 SoCs

PATCH Superseded Cristian Ciocaltea 2 participants 15 messages Jun 17, 2020 – Jun 22, 2020 1 message not in the archive

Subsystems (4)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#3 lore raw

PATCH 3/11 arm: dts: owl-s500: Set UART clock refs from CMU

In reply to Cristian Ciocaltea

Enable using Clock Management Unit clocks for every UART node of the Actions Semi S500 SoC.

---
 arch/arm/boot/dts/owl-s500.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)
arch/arm/boot/dts/owl-s500.dtsi +7 -0
index 5d5ad9db549b..ac3d04c75dd5 100644
@@ -131,6 +131,7 @@ uart0: serial@b0120000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb0120000 0x2000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART0>;
 			status = "disabled";
 		};
 
@@ -138,6 +139,7 @@ uart1: serial@b0122000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb0122000 0x2000>;
 			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART1>;
 			status = "disabled";
 		};
 
@@ -145,6 +147,7 @@ uart2: serial@b0124000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb0124000 0x2000>;
 			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART2>;
 			status = "disabled";
 		};
 
@@ -152,6 +155,7 @@ uart3: serial@b0126000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb0126000 0x2000>;
 			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART3>;
 			status = "disabled";
 		};
 
@@ -159,6 +163,7 @@ uart4: serial@b0128000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb0128000 0x2000>;
 			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART4>;
 			status = "disabled";
 		};
 
@@ -166,6 +171,7 @@ uart5: serial@b012a000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb012a000 0x2000>;
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART5>;
 			status = "disabled";
 		};
 
@@ -173,6 +179,7 @@ uart6: serial@b012c000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb012c000 0x2000>;
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART6>;
 			status = "disabled";
 		};
 
Signature · 1 line
2.27.0
#0 lore raw

cover Add CMU/RMU/DMA support for Actions Semi S500 SoCs

This patch series improves the existing implementation of the Clock Management Unit for the Actions Semi S500 SoC, by adding support for some missing clocks, like DMAC and GPIO.

Additionally, it enables the UART nodes in the common owl-s500 DTS to use the clock provided by the CMU. That means the S500 based SBCs can now get rid of their (fake) UART fixed clock and, as a matter of fact, this has been already done here for RoseapplePi, the new board which is going to be supported (hopefully) via the following patchset:
https://lore.kernel.org/lkml/[email protected]/

Eventually, the patchset adds support for the Actions Semi S500 SoC's DMA controller and Reset Management Unit. Please note the already existing Actions Semi Owl SoCs DMA driver seems to be fully compatible with S500, even though this is not explicitly mentioned in the source code. For the moment, I have just enabled the DMA controller node in owl-s500 DTS using the "actions,s900-dma" compatible string.

In the upcoming patch series I will provide a pinctrl driver and enable access to MMC and I2C.

Thanks,
Cristi

Cristian Ciocaltea (11):
clk: actions: Fix h_clk for Actions S500 SoC
arm: dts: owl-s500: Add Clock Management Unit
arm: dts: owl-s500: Set UART clock refs from CMU
arm: dts: owl-s500-roseapplepi: Use UART clock from CMU
dt-bindings: clock: Add APB, DMAC, GPIO bindings for Actions S500 SoC
clk: actions: Add APB, DMAC, GPIO clock support for Actions S500 SoC
arm: dts: owl-s500: Add DMA controller
dt-bindings: reset: Add binding constants for Actions S500 RMU
clk: actions: Add Actions S500 SoC Reset Management Unit support
arm: dts: owl-s500: Add Reset Controller support
MAINTAINERS: Add reset binding entry for Actions Semi Owl SoCs

 MAINTAINERS                                   |  1 +
 arch/arm/boot/dts/owl-s500-roseapplepi.dts    |  7 --
 arch/arm/boot/dts/owl-s500.dtsi               | 37 ++++++++
 drivers/clk/actions/owl-s500.c                | 91 ++++++++++++++++++-
 include/dt-bindings/clock/actions,s500-cmu.h  | 77 ++++++++--------
 .../dt-bindings/reset/actions,s500-reset.h    | 67 ++++++++++++++
 6 files changed, 235 insertions(+), 45 deletions(-)
 create mode 100644 include/dt-bindings/reset/actions,s500-reset.h
Signature · 7 lines
2.27.0


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#13 lore raw

PATCH 11/11 MAINTAINERS: Add reset binding entry for Actions Semi Owl SoCs

Add a reset binding entry to match all members of Actions Semi Owl SoCs.

---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)
MAINTAINERS +1 -0
index 68f21d46614c..f1ba24ee0eae 100644
@@ -1533,6 +1533,7 @@ F:	drivers/mmc/host/owl-mmc.c
 F:	drivers/pinctrl/actions/*
 F:	drivers/soc/actions/
 F:	include/dt-bindings/power/owl-*
+F:	include/dt-bindings/reset/actions,*-reset.h
 F:	include/linux/soc/actions/
 N:	owl
 
Signature · 1 line
2.27.0
#12 lore raw

PATCH 10/11 arm: dts: owl-s500: Add Reset Controller support

In reply to Cristian Ciocaltea

Add reset controller property and bindings header for the Actions Semi S500 SoC DTS.

---
 arch/arm/boot/dts/owl-s500.dtsi | 2 ++
 1 file changed, 2 insertions(+)
arch/arm/boot/dts/owl-s500.dtsi +2 -0
index 0f4fc5487dad..0b7ba2926f0e 100644
@@ -8,6 +8,7 @@
 #include <dt-bindings/clock/actions,s500-cmu.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/power/owl-s500-powergate.h>
+#include <dt-bindings/reset/actions,s500-reset.h>
 
 / {
 	compatible = "actions,s500";
@@ -188,6 +189,7 @@ cmu: clock-controller@b0160000 {
 			reg = <0xb0160000 0x8000>;
 			clocks = <&hosc>, <&losc>;
 			#clock-cells = <1>;
+			#reset-cells = <1>;
 		};
 
 		timer: timer@b0168000 {
Signature · 1 line
2.27.0
#1 lore raw

PATCH 1/11 clk: actions: Fix h_clk for Actions S500 SoC

In reply to Cristian Ciocaltea

The h_clk clock in the Actions Semi S500 SoC clock driver has an invalid parent. Replace with the correct one.

---
 drivers/clk/actions/owl-s500.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/clk/actions/owl-s500.c +1 -1
index e2007ac4d235..0eb83a0b70bc 100644
@@ -183,7 +183,7 @@ static OWL_GATE(timer_clk, "timer_clk", "hosc", CMU_DEVCLKEN1, 27, 0, 0);
 static OWL_GATE(hdmi_clk, "hdmi_clk", "hosc", CMU_DEVCLKEN1, 3, 0, 0);
 
 /* divider clocks */
-static OWL_DIVIDER(h_clk, "h_clk", "ahbprevdiv_clk", CMU_BUSCLK1, 12, 2, NULL, 0, 0);
+static OWL_DIVIDER(h_clk, "h_clk", "ahbprediv_clk", CMU_BUSCLK1, 12, 2, NULL, 0, 0);
 static OWL_DIVIDER(rmii_ref_clk, "rmii_ref_clk", "ethernet_pll_clk", CMU_ETHERNETPLL, 1, 1, rmii_ref_div_table, 0, 0);
 
 /* factor clocks */
Signature · 7 lines
2.27.0


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#9 lore raw

PATCH 9/11 clk: actions: Add Actions S500 SoC Reset Management Unit support

In reply to Cristian Ciocaltea

Add Reset Management Unit (RMU) support for Actions Semi S500 SoC.

---
 drivers/clk/actions/owl-s500.c | 80 ++++++++++++++++++++++++++++++++++
 1 file changed, 80 insertions(+)
drivers/clk/actions/owl-s500.c +80 -0
index 025a8f6d6482..3bce72301c65 100644
@@ -10,6 +10,8 @@
  *
  * Copyright (c) 2018 LSI-TEC - Caninos Loucos
  * Author: Edgar Bernardi Righi <[email protected]>
+ *
+ * Copyright (c) 2020 Cristian Ciocaltea <[email protected]>
  */
 
 #include <linux/clk-provider.h>
@@ -23,8 +25,10 @@
 #include "owl-gate.h"
 #include "owl-mux.h"
 #include "owl-pll.h"
+#include "owl-reset.h"
 
 #include <dt-bindings/clock/actions,s500-cmu.h>
+#include <dt-bindings/reset/actions,s500-reset.h>
 
 #define CMU_COREPLL			(0x0000)
 #define CMU_DEVPLL			(0x0004)
@@ -497,20 +501,96 @@ static struct clk_hw_onecell_data s500_hw_clks = {
 	.num = CLK_NR_CLKS,
 };
 
+static const struct owl_reset_map s500_resets[] = {
+	[RESET_DMAC]	= { CMU_DEVRST0, BIT(0) },
+	[RESET_NORIF]	= { CMU_DEVRST0, BIT(1) },
+	[RESET_DDR]	= { CMU_DEVRST0, BIT(2) },
+	[RESET_NANDC]	= { CMU_DEVRST0, BIT(3) },
+	[RESET_SD0]	= { CMU_DEVRST0, BIT(4) },
+	[RESET_SD1]	= { CMU_DEVRST0, BIT(5) },
+	[RESET_PCM1]	= { CMU_DEVRST0, BIT(6) },
+	[RESET_DE]	= { CMU_DEVRST0, BIT(7) },
+	[RESET_LCD]	= { CMU_DEVRST0, BIT(8) },
+	[RESET_SD2]	= { CMU_DEVRST0, BIT(9) },
+	[RESET_DSI]	= { CMU_DEVRST0, BIT(10) },
+	[RESET_CSI]	= { CMU_DEVRST0, BIT(11) },
+	[RESET_BISP]	= { CMU_DEVRST0, BIT(12) },
+	[RESET_KEY]	= { CMU_DEVRST0, BIT(14) },
+	[RESET_GPIO]	= { CMU_DEVRST0, BIT(15) },
+	[RESET_AUDIO]	= { CMU_DEVRST0, BIT(17) },
+	[RESET_PCM0]	= { CMU_DEVRST0, BIT(18) },
+	[RESET_VDE]	= { CMU_DEVRST0, BIT(19) },
+	[RESET_VCE]	= { CMU_DEVRST0, BIT(20) },
+	[RESET_GPU3D]	= { CMU_DEVRST0, BIT(22) },
+	[RESET_NIC301]	= { CMU_DEVRST0, BIT(23) },
+	[RESET_LENS]	= { CMU_DEVRST0, BIT(26) },
+	[RESET_PERIPHRESET] = { CMU_DEVRST0, BIT(27) },
+	[RESET_USB2_0]	= { CMU_DEVRST1, BIT(0) },
+	[RESET_TVOUT]	= { CMU_DEVRST1, BIT(1) },
+	[RESET_HDMI]	= { CMU_DEVRST1, BIT(2) },
+	[RESET_HDCP2TX]	= { CMU_DEVRST1, BIT(3) },
+	[RESET_UART6]	= { CMU_DEVRST1, BIT(4) },
+	[RESET_UART0]	= { CMU_DEVRST1, BIT(5) },
+	[RESET_UART1]	= { CMU_DEVRST1, BIT(6) },
+	[RESET_UART2]	= { CMU_DEVRST1, BIT(7) },
+	[RESET_SPI0]	= { CMU_DEVRST1, BIT(8) },
+	[RESET_SPI1]	= { CMU_DEVRST1, BIT(9) },
+	[RESET_SPI2]	= { CMU_DEVRST1, BIT(10) },
+	[RESET_SPI3]	= { CMU_DEVRST1, BIT(11) },
+	[RESET_I2C0]	= { CMU_DEVRST1, BIT(12) },
+	[RESET_I2C1]	= { CMU_DEVRST1, BIT(13) },
+	[RESET_USB3]	= { CMU_DEVRST1, BIT(14) },
+	[RESET_UART3]	= { CMU_DEVRST1, BIT(15) },
+	[RESET_UART4]	= { CMU_DEVRST1, BIT(16) },
+	[RESET_UART5]	= { CMU_DEVRST1, BIT(17) },
+	[RESET_I2C2]	= { CMU_DEVRST1, BIT(18) },
+	[RESET_I2C3]	= { CMU_DEVRST1, BIT(19) },
+	[RESET_ETHERNET] = { CMU_DEVRST1, BIT(20) },
+	[RESET_CHIPID]	= { CMU_DEVRST1, BIT(21) },
+	[RESET_USB2_1]	= { CMU_DEVRST1, BIT(22) },
+	[RESET_WD0RESET] = { CMU_DEVRST1, BIT(24) },
+	[RESET_WD1RESET] = { CMU_DEVRST1, BIT(25) },
+	[RESET_WD2RESET] = { CMU_DEVRST1, BIT(26) },
+	[RESET_WD3RESET] = { CMU_DEVRST1, BIT(27) },
+	[RESET_DBG0RESET] = { CMU_DEVRST1, BIT(28) },
+	[RESET_DBG1RESET] = { CMU_DEVRST1, BIT(29) },
+	[RESET_DBG2RESET] = { CMU_DEVRST1, BIT(30) },
+	[RESET_DBG3RESET] = { CMU_DEVRST1, BIT(31) },
+};
+
 static struct owl_clk_desc s500_clk_desc = {
 	.clks	    = s500_clks,
 	.num_clks   = ARRAY_SIZE(s500_clks),
 
 	.hw_clks    = &s500_hw_clks,
+
+	.resets     = s500_resets,
+	.num_resets = ARRAY_SIZE(s500_resets),
 };
 
 static int s500_clk_probe(struct platform_device *pdev)
 {
 	struct owl_clk_desc *desc;
+	struct owl_reset *reset;
+	int ret;
 
 	desc = &s500_clk_desc;
 	owl_clk_regmap_init(pdev, desc);
 
+	reset = devm_kzalloc(&pdev->dev, sizeof(*reset), GFP_KERNEL);
+	if (!reset)
+		return -ENOMEM;
+
+	reset->rcdev.of_node = pdev->dev.of_node;
+	reset->rcdev.ops = &owl_reset_ops;
+	reset->rcdev.nr_resets = desc->num_resets;
+	reset->reset_map = desc->resets;
+	reset->regmap = desc->regmap;
+
+	ret = devm_reset_controller_register(&pdev->dev, &reset->rcdev);
+	if (ret)
+		dev_err(&pdev->dev, "Failed to register reset controller\n");
+
 	return owl_clk_probe(&pdev->dev, desc->hw_clks);
 }
 
Signature · 1 line
2.27.0
#8 lore raw

PATCH 8/11 dt-bindings: reset: Add binding constants for Actions S500 RMU

In reply to Cristian Ciocaltea

Add device tree binding constants for Actions Semi S500 SoC Reset Management Unit (RMU).

---
 .../dt-bindings/reset/actions,s500-reset.h    | 67 +++++++++++++++++++
 1 file changed, 67 insertions(+)
 create mode 100644 include/dt-bindings/reset/actions,s500-reset.h
include/dt-bindings/reset/actions,s500-reset.h new file +67 -0
new file mode 100644
index 000000000000..f5d94176d10b
@@ -0,0 +1,67 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Device Tree binding constants for Actions Semi S500 Reset Management Unit
+ *
+ * Copyright (c) 2014 Actions Semi Inc.
+ * Copyright (c) 2020 Cristian Ciocaltea <[email protected]>
+ */
+
+#ifndef __DT_BINDINGS_ACTIONS_S500_RESET_H
+#define __DT_BINDINGS_ACTIONS_S500_RESET_H
+
+#define RESET_DMAC				0
+#define RESET_NORIF				1
+#define RESET_DDR				2
+#define RESET_NANDC				3
+#define RESET_SD0				4
+#define RESET_SD1				5
+#define RESET_PCM1				6
+#define RESET_DE				7
+#define RESET_LCD				8
+#define RESET_SD2				9
+#define RESET_DSI				10
+#define RESET_CSI				11
+#define RESET_BISP				12
+#define RESET_KEY				13
+#define RESET_GPIO				14
+#define RESET_AUDIO				15
+#define RESET_PCM0				16
+#define RESET_VDE				17
+#define RESET_VCE				18
+#define RESET_GPU3D				19
+#define RESET_NIC301				20
+#define RESET_LENS				21
+#define RESET_PERIPHRESET			22
+#define RESET_USB2_0				23
+#define RESET_TVOUT				24
+#define RESET_HDMI				25
+#define RESET_HDCP2TX				26
+#define RESET_UART6				27
+#define RESET_UART0				28
+#define RESET_UART1				29
+#define RESET_UART2				30
+#define RESET_SPI0				31
+#define RESET_SPI1				32
+#define RESET_SPI2				33
+#define RESET_SPI3				34
+#define RESET_I2C0				35
+#define RESET_I2C1				36
+#define RESET_USB3				37
+#define RESET_UART3				38
+#define RESET_UART4				39
+#define RESET_UART5				40
+#define RESET_I2C2				41
+#define RESET_I2C3				42
+#define RESET_ETHERNET				43
+#define RESET_CHIPID				44
+#define RESET_USB2_1				45
+#define RESET_WD0RESET				46
+#define RESET_WD1RESET				47
+#define RESET_WD2RESET				48
+#define RESET_WD3RESET				49
+#define RESET_DBG0RESET				50
+#define RESET_DBG1RESET				51
+#define RESET_DBG2RESET				52
+#define RESET_DBG3RESET				53
+
+#endif /* __DT_BINDINGS_ACTIONS_S500_RESET_H */
Signature · 1 line
2.27.0
#2 lore raw

PATCH 2/11 arm: dts: owl-s500: Add Clock Management Unit

In reply to Cristian Ciocaltea

Add Clock Management Unit for Actions Semi S500 SoC.

---
 arch/arm/boot/dts/owl-s500.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
arch/arm/boot/dts/owl-s500.dtsi +14 -0
index 1dbe4e8b38ac..5d5ad9db549b 100644
@@ -5,6 +5,7 @@
  * Copyright (c) 2016-2017 Andreas Färber
  */
 
+#include <dt-bindings/clock/actions,s500-cmu.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/power/owl-s500-powergate.h>
 
@@ -70,6 +71,12 @@ hosc: hosc {
 		#clock-cells = <0>;
 	};
 
+	losc: losc {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -169,6 +176,13 @@ uart6: serial@b012c000 {
 			status = "disabled";
 		};
 
+		cmu: clock-controller@b0160000 {
+			compatible = "actions,s500-cmu";
+			reg = <0xb0160000 0x8000>;
+			clocks = <&hosc>, <&losc>;
+			#clock-cells = <1>;
+		};
+
 		timer: timer@b0168000 {
 			compatible = "actions,s500-timer";
 			reg = <0xb0168000 0x8000>;
Signature · 1 line
2.27.0
#7 lore raw

PATCH 7/11 arm: dts: owl-s500: Add DMA controller

In reply to Cristian Ciocaltea

Add DMA controller node for Actions Semi S500 SoC.

---
 arch/arm/boot/dts/owl-s500.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
arch/arm/boot/dts/owl-s500.dtsi +14 -0
index ac3d04c75dd5..0f4fc5487dad 100644
@@ -205,5 +205,19 @@ sps: power-controller@b01b0100 {
 			reg = <0xb01b0100 0x100>;
 			#power-domain-cells = <1>;
 		};
+
+		dma: dma-controller@b0260000 {
+			compatible = "actions,s900-dma";
+			reg = <0xb0260000 0xd00>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			dma-channels = <12>;
+			dma-requests = <46>;
+			clocks = <&cmu CLK_DMAC>;
+			power-domains = <&sps S500_PD_DMA>;
+		};
 	};
 };
Signature · 1 line
2.27.0
#6 lore raw

PATCH 6/11 clk: actions: Add APB, DMAC, GPIO clock support for Actions S500 SoC

In reply to Cristian Ciocaltea

Add support for the missing APB, DMAC and GPIO clocks in the Actions Semi S500 SoC clock driver.

---
 drivers/clk/actions/owl-s500.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/clk/actions/owl-s500.c +9 -0
index 0eb83a0b70bc..025a8f6d6482 100644
@@ -175,6 +175,8 @@ static OWL_MUX(dev_clk, "dev_clk", dev_clk_mux_p, CMU_DEVPLL, 12, 1, CLK_SET_RAT
 static OWL_MUX(ahbprediv_clk, "ahbprediv_clk", ahbprediv_clk_mux_p, CMU_BUSCLK1, 8, 3, CLK_SET_RATE_PARENT);
 
 /* gate clocks */
+static OWL_GATE(gpio_clk, "gpio_clk", "apb_clk", CMU_DEVCLKEN0, 18, 0, 0);
+static OWL_GATE(dmac_clk, "dmac_clk", "h_clk", CMU_DEVCLKEN0, 1, 0, 0);
 static OWL_GATE(spi0_clk, "spi0_clk", "ahb_clk", CMU_DEVCLKEN1, 10, 0, CLK_IGNORE_UNUSED);
 static OWL_GATE(spi1_clk, "spi1_clk", "ahb_clk", CMU_DEVCLKEN1, 11, 0, CLK_IGNORE_UNUSED);
 static OWL_GATE(spi2_clk, "spi2_clk", "ahb_clk", CMU_DEVCLKEN1, 12, 0, CLK_IGNORE_UNUSED);
@@ -184,6 +186,7 @@ static OWL_GATE(hdmi_clk, "hdmi_clk", "hosc", CMU_DEVCLKEN1, 3, 0, 0);
 
 /* divider clocks */
 static OWL_DIVIDER(h_clk, "h_clk", "ahbprediv_clk", CMU_BUSCLK1, 12, 2, NULL, 0, 0);
+static OWL_DIVIDER(apb_clk, "apb_clk", "ahb_clk", CMU_BUSCLK1, 14, 2, NULL, 0, 0);
 static OWL_DIVIDER(rmii_ref_clk, "rmii_ref_clk", "ethernet_pll_clk", CMU_ETHERNETPLL, 1, 1, rmii_ref_div_table, 0, 0);
 
 /* factor clocks */
@@ -428,6 +431,9 @@ static struct owl_clk_common *s500_clks[] = {
 	&spdif_clk.common,
 	&nand_clk.common,
 	&ecc_clk.common,
+	&apb_clk.common,
+	&dmac_clk.common,
+	&gpio_clk.common,
 };
 
 static struct clk_hw_onecell_data s500_hw_clks = {
@@ -484,6 +490,9 @@ static struct clk_hw_onecell_data s500_hw_clks = {
 		[CLK_SPDIF]		= &spdif_clk.common.hw,
 		[CLK_NAND]		= &nand_clk.common.hw,
 		[CLK_ECC]		= &ecc_clk.common.hw,
+		[CLK_APB]		= &apb_clk.common.hw,
+		[CLK_DMAC]		= &dmac_clk.common.hw,
+		[CLK_GPIO]		= &gpio_clk.common.hw,
 	},
 	.num = CLK_NR_CLKS,
 };
Signature · 1 line
2.27.0
#5 lore raw

PATCH 5/11 dt-bindings: clock: Add APB, DMAC, GPIO bindings for Actions S500 SoC

In reply to Cristian Ciocaltea

Add the missing APB, DMAC and GPIO clock bindings constants for Actions Semi S500 SoC.

---
 include/dt-bindings/clock/actions,s500-cmu.h | 77 ++++++++++----------
 1 file changed, 40 insertions(+), 37 deletions(-)
include/dt-bindings/clock/actions,s500-cmu.h +40 -37
index 030981cd2d56..a391d1651257 100644
@@ -33,45 +33,48 @@
 #define CLK_BISP		15
 #define CLK_VCE			16
 #define CLK_VDE			17
+#define CLK_APB			18
+#define CLK_DMAC		19
 
 /* peripheral device clock */
-#define CLK_TIMER		18
-#define CLK_I2C0		19
-#define CLK_I2C1		20
-#define CLK_I2C2		21
-#define CLK_I2C3		22
-#define CLK_PWM0		23
-#define CLK_PWM1		24
-#define CLK_PWM2		25
-#define CLK_PWM3		26
-#define CLK_PWM4		27
-#define CLK_PWM5		28
-#define CLK_SD0			29
-#define CLK_SD1			30
-#define CLK_SD2			31
-#define CLK_SENSOR0		32
-#define CLK_SENSOR1		33
-#define CLK_SPI0		34
-#define CLK_SPI1		35
-#define CLK_SPI2		36
-#define CLK_SPI3		37
-#define CLK_UART0		38
-#define CLK_UART1		39
-#define CLK_UART2		40
-#define CLK_UART3		41
-#define CLK_UART4		42
-#define CLK_UART5		43
-#define CLK_UART6		44
-#define CLK_DE1			45
-#define CLK_DE2			46
-#define CLK_I2SRX		47
-#define CLK_I2STX		48
-#define CLK_HDMI_AUDIO		49
-#define CLK_HDMI		50
-#define CLK_SPDIF		51
-#define CLK_NAND		52
-#define CLK_ECC			53
-#define CLK_RMII_REF		54
+#define CLK_GPIO		20
+#define CLK_TIMER		21
+#define CLK_I2C0		22
+#define CLK_I2C1		23
+#define CLK_I2C2		24
+#define CLK_I2C3		25
+#define CLK_PWM0		26
+#define CLK_PWM1		27
+#define CLK_PWM2		28
+#define CLK_PWM3		29
+#define CLK_PWM4		30
+#define CLK_PWM5		31
+#define CLK_SD0			32
+#define CLK_SD1			33
+#define CLK_SD2			34
+#define CLK_SENSOR0		35
+#define CLK_SENSOR1		36
+#define CLK_SPI0		37
+#define CLK_SPI1		38
+#define CLK_SPI2		39
+#define CLK_SPI3		40
+#define CLK_UART0		41
+#define CLK_UART1		42
+#define CLK_UART2		43
+#define CLK_UART3		44
+#define CLK_UART4		45
+#define CLK_UART5		46
+#define CLK_UART6		47
+#define CLK_DE1			48
+#define CLK_DE2			49
+#define CLK_I2SRX		50
+#define CLK_I2STX		51
+#define CLK_HDMI_AUDIO		52
+#define CLK_HDMI		53
+#define CLK_SPDIF		54
+#define CLK_NAND		55
+#define CLK_ECC			56
+#define CLK_RMII_REF		57
 
 #define CLK_NR_CLKS	       (CLK_RMII_REF + 1)
 
Signature · 1 line
2.27.0
#4 lore raw

PATCH 4/11 arm: dts: owl-s500-roseapplepi: Use UART clock from CMU

In reply to Cristian Ciocaltea

Remove the UART fixed clock and enable using the one provided by CMU.

---
 arch/arm/boot/dts/owl-s500-roseapplepi.dts | 7 -------
 1 file changed, 7 deletions(-)
arch/arm/boot/dts/owl-s500-roseapplepi.dts +0 -7
index a2087e617cb2..800edf5d2d12 100644
@@ -25,12 +25,6 @@ memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x80000000>; /* 2GB */
 	};
-
-	uart2_clk: uart2-clk {
-		compatible = "fixed-clock";
-		clock-frequency = <921600>;
-		#clock-cells = <0>;
-	};
 };
 
 &twd_timer {
@@ -43,5 +37,4 @@ &timer {
 
 &uart2 {
 	status = "okay";
-	clocks = <&uart2_clk>;
 };
Signature · 1 line
2.27.0
maintainer
#10 lore raw

Re: [PATCH 09/11] clk: actions: Add Actions S500 SoC Reset Management Unit support

In reply to Cristian Ciocaltea

Quoting Cristian Ciocaltea (2020-06-17 09:48:09)

Quoted 12 lines

Add Reset Management Unit (RMU) support for Actions Semi S500 SoC.

---
 drivers/clk/actions/owl-s500.c | 80 ++++++++++++++++++++++++++++++++++
 1 file changed, 80 insertions(+)
drivers/clk/actions/owl-s500.c +0 -0
index 025a8f6d6482..3bce72301c65 100644

drivers/clk/actions/owl-s500.c line 14

Quoted 5 lines
drivers/clk/actions/owl-s500.c +2 -0
@@ -10,6 +10,8 @@
  *
  * Copyright (c) 2018 LSI-TEC - Caninos Loucos
  * Author: Edgar Bernardi Righi <[email protected]>
+ *
+ * Copyright (c) 2020 Cristian Ciocaltea <[email protected]>

You should only add your copyright when you modify a large amount of the file. Adding 80 lines to a 500 line file doesn't count. Sorry.

Quoted 3 lines
drivers/clk/actions/owl-s500.c +0 -0
  */
 
 #include <linux/clk-provider.h>
#15 lore raw
In reply to a message not in the archive
Quoted 19 lines · Stephen Boyd

Quoting Cristian Ciocaltea (2020-06-17 09:48:00)

Quoted 18 lines

This patch series improves the existing implementation of the Clock Management Unit for the Actions Semi S500 SoC, by adding support for some missing clocks, like DMAC and GPIO.

Additionally, it enables the UART nodes in the common owl-s500 DTS to use the clock provided by the CMU. That means the S500 based SBCs can now get rid of their (fake) UART fixed clock and, as a matter of fact, this has been already done here for RoseapplePi, the new board which is going to be supported (hopefully) via the following patchset:
https://lore.kernel.org/lkml/[email protected]/

Eventually, the patchset adds support for the Actions Semi S500 SoC's DMA controller and Reset Management Unit. Please note the already existing Actions Semi Owl SoCs DMA driver seems to be fully compatible with S500, even though this is not explicitly mentioned in the source code. For the moment, I have just enabled the DMA controller node in owl-s500 DTS using the "actions,s900-dma" compatible string.

Quoted 8 lines
Quoted 3 lines

In the upcoming patch series I will provide a pinctrl driver and enable access to MMC and I2C.

Can you please untangle this from the DTS changes? The clk driver changes will go through the clk tree and the DTS changes will go through arm-soc. Please send them as separate patch series to the respective maintainers.

Hi Stephen,

Thank you for reviewing!
I will submit v2 having the DTS related changes removed from this patch series.

Regards,
Cristi

#11 lore raw

Re: [PATCH 09/11] clk: actions: Add Actions S500 SoC Reset Management Unit support

In reply to Stephen Boyd
Quoted 8 lines · Stephen Boyd

Quoting Cristian Ciocaltea (2020-06-17 09:48:09)

Quoted 7 lines

Add Reset Management Unit (RMU) support for Actions Semi S500 SoC.

---
 drivers/clk/actions/owl-s500.c | 80 ++++++++++++++++++++++++++++++++++
 1 file changed, 80 insertions(+)
Quoted 14 lines

drivers/clk/actions/owl-s500.c line 14

Quoted 10 lines
drivers/clk/actions/owl-s500.c +2 -0
index 025a8f6d6482..3bce72301c65 100644
@@ -10,6 +10,8 @@
  *
  * Copyright (c) 2018 LSI-TEC - Caninos Loucos
  * Author: Edgar Bernardi Righi <[email protected]>
+ *
+ * Copyright (c) 2020 Cristian Ciocaltea <[email protected]>

You should only add your copyright when you modify a large amount of the file. Adding 80 lines to a 500 line file doesn't count. Sorry.

Sure, I removed it. Thanks!

Quoted 3 lines
Quoted 3 lines
drivers/clk/actions/owl-s500.c +0 -0
  */
 
 #include <linux/clk-provider.h>