Skip to contentSkip to conversation

microblaze: Cleanup series

PATCH Superseded Michal Simek 1 participant 7 messages Nov 4, 2020 Arm/Zynq architecture

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

cover microblaze: Cleanup series

Hi,

I looked at microblaze configs and clean up some things. All changes were done in connection to detect nor flash based on information taken from DT.

Thanks
Michal

Michal Simek (6):
microblaze: Clean config file from ifdef mess
microblaze: Simplify cache handling
microblaze: Get rid of xparameters.h
microblaze: Remove CONFIG_SYS_FDT_SIZE
microblaze: Get rid of setting for SPL_NOR/XIP support
microblaze: Detect NOR flash based on DT

 board/xilinx/microblaze-generic/xparameters.h | 18 ----
 configs/microblaze-generic_defconfig          |  2 +
 include/configs/microblaze-generic.h          | 86 ++-----------------
 scripts/config_whitelist.txt                  |  1 -
 4 files changed, 8 insertions(+), 99 deletions(-)
 delete mode 100644 board/xilinx/microblaze-generic/xparameters.h
Signature · 1 line
2.29.2
#1 lore raw

PATCH 1/6 microblaze: Clean config file from ifdef mess

A lot of configs has been moved to Kconfig and it ends up in ifdef mess with no bodies. That's why remove all of them.

---

 include/configs/microblaze-generic.h | 24 ------------------------
 1 file changed, 24 deletions(-)
include/configs/microblaze-generic.h +0 -24
index 2b4124235082..d5b2bd856608 100644
@@ -67,24 +67,6 @@
 # define CONFIG_SYS_MAX_FLASH_BANKS	1
 /* max number of sectors on one chip */
 # define CONFIG_SYS_MAX_FLASH_SECT	512
-/* hardware flash protection */
-/* use buffered writes (20x faster) */
-# ifdef	RAMENV
-# else	/* FLASH && !RAMENV */
-/* 128K(one sector) for env */
-# endif /* FLASH && !RAMBOOT */
-#else /* !FLASH */
-
-#ifdef SPIFLASH
-# ifdef	RAMENV
-# else	/* SPIFLASH && !RAMENV */
-/* 128K(two sectors) for env */
-/* Warning: adjust the offset in respect of other flash content and size */
-# endif /* SPIFLASH && !RAMBOOT */
-#else /* !SPIFLASH */
-
-/* ENV in RAM */
-#endif /* !SPIFLASH */
 #endif /* !FLASH */
 
 #define XILINX_USE_ICACHE 1
@@ -111,12 +93,6 @@
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 
-#if defined(CONFIG_MTD_PARTITIONS)
-/* MTD partitions */
-
-/* default mtd partition table */
-#endif
-
 /* size of console buffer */
 #define	CONFIG_SYS_CBSIZE	512
 /* max number of command args */
Signature · 1 line
2.29.2
#2 lore raw

PATCH 2/6 microblaze: Simplify cache handling

In reply to Michal Simek

Enable caches by default. For now just simplify config file but it should be read from DT or PVRs.

---

 include/configs/microblaze-generic.h | 16 ++--------------
 1 file changed, 2 insertions(+), 14 deletions(-)
include/configs/microblaze-generic.h +2 -14
index d5b2bd856608..05ea64b16312 100644
@@ -69,20 +69,8 @@
 # define CONFIG_SYS_MAX_FLASH_SECT	512
 #endif /* !FLASH */
 
-#define XILINX_USE_ICACHE 1
-#define XILINX_USE_DCACHE 1
-
-#if defined(XILINX_USE_ICACHE)
-# define CONFIG_ICACHE
-#else
-# undef CONFIG_ICACHE
-#endif
-
-#if defined(XILINX_USE_DCACHE)
-# define CONFIG_DCACHE
-#else
-# undef CONFIG_DCACHE
-#endif
+#define CONFIG_ICACHE
+#define CONFIG_DCACHE
 
 #ifndef XILINX_DCACHE_BYTE_SIZE
 #define XILINX_DCACHE_BYTE_SIZE	32768
Signature · 1 line
2.29.2
#3 lore raw

PATCH 3/6 microblaze: Get rid of xparameters.h

In reply to Michal Simek

There is no need to use this file anymore. Include it in main config file and simplify logic based on it.

---

 board/xilinx/microblaze-generic/xparameters.h | 18 ------------------
 include/configs/microblaze-generic.h          |  7 ++++++-
 2 files changed, 6 insertions(+), 19 deletions(-)
 delete mode 100644 board/xilinx/microblaze-generic/xparameters.h
board/xilinx/microblaze-generic/xparameters.h deleted +0 -18
deleted file mode 100644
index 5e0911faf633..000000000000
@@ -1,18 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2007 Michal Simek
- *
- * Michal  SIMEK <[email protected]>
- *
- * CAUTION: This file is a faked configuration !!!
- *          There is no real target for the microblaze-generic
- *          configuration. You have to replace this file with
- *          the generated file from your Xilinx design flow.
- */
-
-/* Microblaze is microblaze_0 */
-#define XILINX_FSL_NUMBER	3
-
-/* Flash Memory is FLASH_2Mx32 */
-#define XILINX_FLASH_START	0x2c000000
-#define XILINX_FLASH_SIZE	0x00800000
include/configs/microblaze-generic.h +6 -1
index 05ea64b16312..2cfcace7b066 100644
@@ -8,7 +8,12 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#include "../board/xilinx/microblaze-generic/xparameters.h"
+/* Microblaze is microblaze_0 */
+#define XILINX_FSL_NUMBER	3
+
+/* Flash Memory is FLASH_2Mx32 */
+#define XILINX_FLASH_START	0x2c000000
+#define XILINX_FLASH_SIZE	0x00800000
 
 /* MicroBlaze CPU */
 #define	MICROBLAZE_V5		1
Signature · 1 line
2.29.2
#4 lore raw

PATCH 4/6 microblaze: Remove CONFIG_SYS_FDT_SIZE

In reply to Michal Simek

CONFIG_SYS_FDT_SIZE is not use anywhere that's why remove it.

---

 include/configs/microblaze-generic.h | 1 -
 scripts/config_whitelist.txt         | 1 -
 2 files changed, 2 deletions(-)
include/configs/microblaze-generic.h +0 -1
index 2cfcace7b066..72550113cefa 100644
@@ -171,7 +171,6 @@
 
 #define CONFIG_SYS_FDT_BASE		(CONFIG_SYS_FLASH_BASE + \
 					 0x40000)
-#define CONFIG_SYS_FDT_SIZE		(16 << 10)
 #define CONFIG_SYS_SPL_ARGS_ADDR	(CONFIG_SYS_TEXT_BASE + \
 					 0x1000000)
 
scripts/config_whitelist.txt +0 -1
index 0aabe7a45165..8b4fcba395a3 100644
@@ -2170,7 +2170,6 @@ CONFIG_SYS_FCC_PSMR
 CONFIG_SYS_FDT_BASE
 CONFIG_SYS_FDT_LOAD_ADDR
 CONFIG_SYS_FDT_PAD
-CONFIG_SYS_FDT_SIZE
 CONFIG_SYS_FEC0_IOBASE
 CONFIG_SYS_FEC1_IOBASE
 CONFIG_SYS_FECI2C
Signature · 1 line
2.29.2
#5 lore raw

PATCH 5/6 microblaze: Get rid of setting for SPL_NOR/XIP support

In reply to Michal Simek

SPL_NOR/XIP is not enabled in SPL that's why no reason to keep macros for it. These macros are hardcoded to certain offset which doesn't work for generic target. Information has to be found at run time based on DT anyway.

---

 include/configs/microblaze-generic.h | 7 -------
 1 file changed, 7 deletions(-)
include/configs/microblaze-generic.h +0 -7
index 72550113cefa..cc68327266e8 100644
@@ -163,14 +163,7 @@
 
 /* SPL part */
 
-#ifdef CONFIG_SYS_FLASH_BASE
-# define CONFIG_SYS_UBOOT_BASE		CONFIG_SYS_FLASH_BASE
-#endif
-
 /* for booting directly linux */
-
-#define CONFIG_SYS_FDT_BASE		(CONFIG_SYS_FLASH_BASE + \
-					 0x40000)
 #define CONFIG_SYS_SPL_ARGS_ADDR	(CONFIG_SYS_TEXT_BASE + \
 					 0x1000000)
 
Signature · 1 line
2.29.2
#6 lore raw

PATCH 6/6 microblaze: Detect NOR flash based on DT

In reply to Michal Simek

Remove fixed configuration and detect flash based on DT.

Also increase amount of flash sectors to 2048 because on kc705 flash has 1027 sectors.

Bank # 1: CFI conformant flash (16 x 16) Size: 128 MB in 1027 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8962 Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes

---

 configs/microblaze-generic_defconfig |  2 ++
 include/configs/microblaze-generic.h | 41 ++--------------------------
 2 files changed, 5 insertions(+), 38 deletions(-)
configs/microblaze-generic_defconfig +2 -0
index 6045e6a0129f..4389ce2e38dd 100644
@@ -54,8 +54,10 @@ CONFIG_DM_I2C=y
 CONFIG_LED=y
 CONFIG_LED_GPIO=y
 CONFIG_MTD=y
+CONFIG_DM_MTD=y
 CONFIG_MTD_NOR_FLASH=y
 CONFIG_FLASH_CFI_DRIVER=y
+CONFIG_CFI_FLASH=y
 CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
 CONFIG_FLASH_CFI_MTD=y
 CONFIG_SYS_FLASH_PROTECTION=y
include/configs/microblaze-generic.h +3 -38

63 lines not on this page · raw message

Signature · 1 line
2.29.2