cxl: CXL Inject & Clear Poison
[email protected]
maintainerv3 cover cxl: CXL Inject & Clear Poison
From: Alison Schofield <[email protected]>
Changes in v3:
- Built on cxl/next plus the Get Poison list patchset here:
https://lore.kernel.org/linux-cxl/[email protected]/
- Two new patches are appended to address Dan's deprecate ask:
cxl/memdev: Make inject and clear poison cmds kernel exclusive cxl/mbox: Block inject and clear poison opcodes in raw mode
I didn't deprecate the ioctls as Dan suggested. Instead, I followed on Ira's recent clean up wrt enabled and exclusive commands, deciding that the honest response to a cxl_query() would be 'Enabled' (if hardware supports) and kernel 'Exclusive' (always). Please take a look.
- Move IS_ENABLED(CONFIG_CXL_POISON_INJECT) test into each attr check (Dan)
- Fail updates to poison_inject_max when poison list is not empty (DaveJ)
- Make poison_inject_max a sysfs attr, rather than module param (Dan)
- Kconfig: add note regarding debug intent (Dan)
- Kept Jonathan's Reviewed-by Tag on Patches 1-6
Link to v2: https://lore.kernel.org/linux-cxl/[email protected]/
Introducing Inject and Clear Poison support for CXL Devices.
These are optional commands, meaning not all CXL devices must support them. The sysfs attributes, inject_poison and clear_poison, are only visible for devices reporting support of the capability and when the kernel Kconfig option CONFIG_CXL_POISON_INJECT is on. (Default: off)
Example:
# echo 0x40000000 > /sys/bus/cxl/devices/mem1/inject_poison # echo 1 > /sys/bus/cxl/devices/mem1/trigger_poison_list
cxl_poison: memdev=mem1 pcidev=cxl_mem.1 region= region_uuid=00000000-0000-0000-0000-000000000000 hpa=0xffffffffffffffff dpa=0x40000000 length=0x40 source=Injected flags= overflow_time=0
Alison Schofield (8):
cxl/memdev: Add support for the Inject Poison mailbox command cxl/memdev: Add support for the Clear Poison mailbox command tools/testing/cxl: Mock the Inject Poison mailbox command tools/testing/cxl: Mock the Clear Poison mailbox command tools/testing/cxl: Use injected poison for get poison list tools/testing/cxl: Add a sysfs attr to test poison injection limits cxl/memdev: Make inject and clear poison cmds kernel exclusive cxl/mbox: Block inject and clear poison opcodes in raw mode
Documentation/ABI/testing/sysfs-bus-cxl | 40 +++++ drivers/cxl/Kconfig | 11 ++ drivers/cxl/core/mbox.c | 6 + drivers/cxl/core/memdev.c | 162 ++++++++++++++++++ drivers/cxl/cxlmem.h | 11 ++ include/uapi/linux/cxl_mem.h | 21 ++- tools/testing/cxl/test/mem.c | 216 +++++++++++++++++++++--- 7 files changed, 443 insertions(+), 24 deletions(-)
Signature · 1 line
2.37.3
[email protected]
maintainerPATCH v3 1/8 cxl/memdev: Add support for the Inject Poison mailbox command
From: Alison Schofield <[email protected]>
CXL devices optionally support the INJECT POISON mailbox command. Add a sysfs attribute and memdev driver support for injecting poison. The attribute is only visible for devices supporting the capability when the kernel is built with CONFIG_CXL_POISON_INJECT.
When a Device Physical Address (DPA) is written to the inject_poison sysfs attribute, send an inject poison command to the device for the specified address.
Per the CXL Specification (3.0 8.2.9.8.4.2), after receiving a valid inject poison request, the device will return poison when the address is accessed through the CXL.mem bus. Injecting poison adds the address to the device's Poison List and the error source is set to Injected. In addition, the device adds a poison creation event to its internal Informational Event log, updates the Event Status register, and if configured, interrupts the host.
Also, per the CXL Specification, it is not an error to inject poison into an address that already has poison present and no error is returned from the device.
--- Documentation/ABI/testing/sysfs-bus-cxl | 22 ++++++ drivers/cxl/Kconfig | 11 +++ drivers/cxl/core/memdev.c | 97 +++++++++++++++++++++++++ drivers/cxl/cxlmem.h | 5 ++ 4 files changed, 135 insertions(+)
Documentation/ABI/testing/sysfs-bus-cxl +22 -0
@@ -429,3 +429,25 @@ Description: attribute is only visible for devices supporting the capability. The retrieved errors are logged as kernel trace events with the label 'cxl_poison'. + + +What: /sys/bus/cxl/devices/memX/inject_poison +Date: January, 2023 +KernelVersion: v6.3 +Contact: [email protected] +Description: + (WO) When a Device Physical Address (DPA) is written to this + attribute, the memdev driver sends an inject poison command to + the device for the specified address. The DPA must be 64-byte + aligned and the length of the injected poison is 64-bytes. If + successful, the device returns poison when the address is + accessed through the CXL.mem bus. Injecting poison adds the + address to the device's Poison List and the error source is set + to Injected. In addition, the device adds a poison creation + event to its internal Informational Event log, updates the + Event Status register, and if configured, interrupts the host. + It is not an error to inject poison into an address that + already has poison present and no error is returned. The + inject_poison attribute is only visible for devices supporting + the capability. Kconfig option CXL_POISON_INJECT must be on + to enable this option. The default is off.
drivers/cxl/Kconfig +11 -0
@@ -139,4 +139,15 @@ config CXL_REGION_INVALIDATION_TEST If unsure, or if this kernel is meant for production environments, say N. +config CXL_POISON_INJECT + bool "CXL: Support CXL Memory Device Poison Inject" + depends on CXL_MEM + help + Selecting this option creates the sysfs attributes inject_poison + and clear_poison for CXL memory devices supporting the capability. + This option is intended for debug scenarios only and is disabled + by default. See Documentation/ABI/testing/sysfs-bus-cxl. + + If unsure, say N. + endif
drivers/cxl/core/memdev.c +97 -0
115 lines not on this page · raw message
drivers/cxl/cxlmem.h +5 -0
@@ -602,6 +602,11 @@ struct cxl_mbox_poison_payload_out {#define CXL_POISON_SOURCE_INJECTED 3#define CXL_POISON_SOURCE_VENDOR 7 +/* Inject & Clear Poison CXL 3.0 Spec 8.2.9.8.4.2/3 */ +struct cxl_mbox_inject_poison { +__le64 address; +}; +/** * struct cxl_mem_command - Driver representation of a memory device command * @info: Command information as it exists for the UAPI
Signature · 1 line
2.37.3
[email protected]
maintainerPATCH v3 2/8 cxl/memdev: Add support for the Clear Poison mailbox command
In reply to [email protected]From: Alison Schofield <[email protected]>
CXL devices optionally support the CLEAR POISON mailbox command. Add a sysfs attribute and memdev driver support for clearing poison. The attribute is only visible for devices supporting the capability when the kernel is built with CONFIG_CXL_POISON_INJECT.
When a Device Physical Address (DPA) is written to the clear_poison sysfs attribute, send a clear poison command to the device for the specified address.
Per the CXL Specification (3.0 8.2.9.8.4.3), after receiving a valid clear poison request, the device removes the address from the device's Poison List and writes 0 (zero) for 64 bytes starting at address. If the device cannot clear poison from the address, it returns a permanent media error and -ENXIO is returned to the user.
Additionally, and per the spec also, it is not an error to clear poison of an address that is not poisoned. In this case, the device does not overwrite the address and the device does not return an error.
*Implementation note: Although the CXL specification defines the clear command to accept 64 bytes of 'write-data' to be used when clearing the poisoned address, this implementation always uses 0 (zeros) for the write-data.
--- Documentation/ABI/testing/sysfs-bus-cxl | 18 ++++++++ drivers/cxl/core/memdev.c | 59 +++++++++++++++++++++++++ drivers/cxl/cxlmem.h | 6 +++ 3 files changed, 83 insertions(+)
Documentation/ABI/testing/sysfs-bus-cxl +18 -0
@@ -451,3 +451,21 @@ Description: inject_poison attribute is only visible for devices supporting the capability. Kconfig option CXL_POISON_INJECT must be on to enable this option. The default is off. + + +What: /sys/bus/cxl/devices/memX/clear_poison +Date: January, 2023 +KernelVersion: v6.3 +Contact: [email protected] +Description: + (WO) When a Device Physical Address (DPA) is written to this + attribute, the memdev driver sends a clear poison command to + the device for the specified address. Clearing poison removes + the address from the device's Poison List and writes 0 (zero) + for 64 bytes starting at address. It is not an error to clear + poison from an address that does not have poison set, and if + poison was not set, the address is not overwritten. If the + device cannot clear poison from the address, -ENXIO is returned. + The clear_poison attribute is only visible for devices + supporting the capability. Kconfig option CXL_POISON_INJECT + must be on to enable this option. The default is off.
drivers/cxl/core/memdev.c +59 -0
77 lines not on this page · raw message
drivers/cxl/cxlmem.h +6 -0
@@ -607,6 +607,12 @@ struct cxl_mbox_inject_poison {__le64 address; }; +/* Clear Poison CXL 3.0 Spec 8.2.9.8.4.3 */ +struct cxl_mbox_clear_poison { +__le64 address; +u8 write_data[CXL_POISON_LEN_MULT ]; +} __packed; +/** * struct cxl_mem_command - Driver representation of a memory device command * @info: Command information as it exists for the UAPI
Signature · 1 line
2.37.3
[email protected]
maintainerPATCH v3 3/8 tools/testing/cxl: Mock the Inject Poison mailbox command
In reply to [email protected]From: Alison Schofield <[email protected]>
Mock the injection of poison by storing the device:address entries in mock_poison_list[]. Enforce a limit of 8 poison injections per memdev device and 128 total entries for the cxl_test mock driver.
Introducing the mock_poison[] list here, makes it available for use in the mock of Clear Poison, and the mock of Get Poison List.
--- tools/testing/cxl/test/mem.c | 77 ++++++++++++++++++++++++++++++++++++ 1 file changed, 77 insertions(+)
tools/testing/cxl/test/mem.c +77 -0
@@ -16,6 +16,9 @@#define DEV_SIZE SZ_2G#define EFFECT (x) (1U << x) +#define MOCK_INJECT_DEV_MAX 8 +#define MOCK_INJECT_TEST_MAX 128 +static struct cxl_cel_entry mock_cel[] = { { .opcode =cpu_to_le16 (CXL_MBOX_OP_GET_SUPPORTED_LOGS ),
@@ -45,6 +48,10 @@ static struct cxl_cel_entry mock_cel[] = { .opcode = cpu_to_le16(CXL_MBOX_OP_GET_POISON), .effect = cpu_to_le16(0), }, + { + .opcode = cpu_to_le16(CXL_MBOX_OP_INJECT_POISON), + .effect = cpu_to_le16(0), + }, };/* See CXL 2.0 Table 181 Get Health Info Output Payload */
@@ -474,6 +481,7 @@ static int mock_id(struct cxl_dev_state *cxlds, struct cxl_mbox_cmd *cmd) cpu_to_le64(SZ_256M / CXL_CAPACITY_MULTIPLIER), .total_capacity = cpu_to_le64(DEV_SIZE / CXL_CAPACITY_MULTIPLIER), + .inject_poison_limit =cpu_to_le16 (MOCK_INJECT_DEV_MAX ), };put_unaligned_le24 (CXL_POISON_LIST_MAX , id.poison_list_max_mer);
@@ -895,6 +903,11 @@ static int mock_health_info(struct cxl_dev_state *cxlds,return 0 ; } +static struct mock_poison { +struct cxl_dev_state *cxlds; +u64 dpa; +} mock_poison_list[MOCK_INJECT_TEST_MAX ]; +static int mock_get_poison (struct cxl_dev_state *cxlds,struct cxl_mbox_cmd *cmd) {
@@ -923,6 +936,67 @@ static int mock_get_poison(struct cxl_dev_state *cxlds,return 0 ; } +static bool mock_poison_dev_max_injected (struct cxl_dev_state *cxlds) +{ +int count =0 ; + +for (int i =0 ; i <MOCK_INJECT_TEST_MAX ; i++) { +if (mock_poison_list[i].cxlds == cxlds) + count++; + } +return (count >=MOCK_INJECT_DEV_MAX ); +} + +static bool mock_poison_add (struct cxl_dev_state *cxlds,u64 dpa) +{ +if (mock_poison_dev_max_injected (cxlds)) { +dev_dbg (cxlds->dev, +"Device poison injection limit has been reached: %d\n" , +MOCK_INJECT_DEV_MAX ); +return false; + } + +for (int i =0 ; i <MOCK_INJECT_TEST_MAX ; i++) { +if (!mock_poison_list[i].cxlds) { + mock_poison_list[i].cxlds = cxlds; + mock_poison_list[i].dpa = dpa; +return true; + } + } +dev_dbg (cxlds->dev, +"Mock test poison injection limit has been reached: %d\n" , +MOCK_INJECT_TEST_MAX ); + +return false; +} + +static bool mock_poison_found (struct cxl_dev_state *cxlds,u64 dpa) +{ +for (int i =0 ; i <MOCK_INJECT_TEST_MAX ; i++) { +if (mock_poison_list[i].cxlds == cxlds && + mock_poison_list[i].dpa == dpa) +return true; + } +return false; +} + +static int mock_inject_poison (struct cxl_dev_state *cxlds, +struct cxl_mbox_cmd *cmd) +{ +struct cxl_mbox_inject_poison *pi = cmd->payload_in; +u64 dpa =le64_to_cpu (pi->address); + +if (mock_poison_found (cxlds, dpa)) { +/* Not an error to inject poison if already poisoned */ +dev_dbg (cxlds->dev,"DPA: 0x%llx already poisoned\n" , dpa); +return 0 ; + } +if (!mock_poison_add (cxlds, dpa)) +return -ENXIO ; + +return 0 ; +} +static int cxl_mock_mbox_send (struct cxl_dev_state *cxlds,struct cxl_mbox_cmd *cmd) {struct device *dev = cxlds->dev;
@@ -980,6 +1054,9 @@ static int cxl_mock_mbox_send(struct cxl_dev_state *cxlds, struct cxl_mbox_cmd *case CXL_MBOX_OP_GET_POISON : rc =mock_get_poison (cxlds, cmd);break ; +case CXL_MBOX_OP_INJECT_POISON : + rc =mock_inject_poison (cxlds, cmd); +break ;default :break ; }
Signature · 1 line
2.37.3
[email protected]
maintainerPATCH v3 4/8 tools/testing/cxl: Mock the Clear Poison mailbox command
In reply to [email protected]From: Alison Schofield <[email protected]>
Mock the clear of poison by deleting the device:address entry from the mock_poison_list[]. Behave like a real CXL device and do not fail if the address is not in the poison list, but offer a dev_dbg() message.
--- tools/testing/cxl/test/mem.c | 36 ++++++++++++++++++++++++++++++++++++ 1 file changed, 36 insertions(+)
tools/testing/cxl/test/mem.c +36 -0
@@ -52,6 +52,10 @@ static struct cxl_cel_entry mock_cel[] = { .opcode = cpu_to_le16(CXL_MBOX_OP_INJECT_POISON), .effect = cpu_to_le16(0), }, + { + .opcode = cpu_to_le16(CXL_MBOX_OP_CLEAR_POISON), + .effect = cpu_to_le16(0), + }, };/* See CXL 2.0 Table 181 Get Health Info Output Payload */
@@ -997,6 +1001,35 @@ static int mock_inject_poison(struct cxl_dev_state *cxlds,return 0 ; } +static bool mock_poison_del (struct cxl_dev_state *cxlds,u64 dpa) +{ +for (int i =0 ; i <MOCK_INJECT_TEST_MAX ; i++) { +if (mock_poison_list[i].cxlds == cxlds && + mock_poison_list[i].dpa == dpa) { + mock_poison_list[i].cxlds =NULL ; +return true; + } + } +return false; +} + +static int mock_clear_poison (struct cxl_dev_state *cxlds, +struct cxl_mbox_cmd *cmd) +{ +struct cxl_mbox_clear_poison *pi = cmd->payload_in; +u64 dpa =le64_to_cpu (pi->address); + +/* +* A real CXL device will write pi->write_data to the address +* being cleared. In this mock, just delete this address from +* the mock poison list. +*/ +if (!mock_poison_del (cxlds, dpa)) +dev_dbg (cxlds->dev,"DPA: 0x%llx not in poison list\n" , dpa); + +return 0 ; +} +static int cxl_mock_mbox_send (struct cxl_dev_state *cxlds,struct cxl_mbox_cmd *cmd) {struct device *dev = cxlds->dev;
@@ -1057,6 +1090,9 @@ static int cxl_mock_mbox_send(struct cxl_dev_state *cxlds, struct cxl_mbox_cmd *case CXL_MBOX_OP_INJECT_POISON : rc =mock_inject_poison (cxlds, cmd);break ; +case CXL_MBOX_OP_CLEAR_POISON : + rc =mock_clear_poison (cxlds, cmd); +break ;default :break ; }
Signature · 1 line
2.37.3
[email protected]
maintainerPATCH v3 5/8 tools/testing/cxl: Use injected poison for get poison list
In reply to [email protected]From: Alison Schofield <[email protected]>
Prior to poison inject support, the mock of 'Get Poison List' returned a poison list containing a single mocked error record.
Following the addition of poison inject and clear support to the mock driver, use the mock_poison_list[], rather than faking an error record. Mock_poison_list[] list tracks the actual poison inject and clear requests issued by userspace.
--- tools/testing/cxl/test/mem.c | 59 ++++++++++++++++++++++++------------ 1 file changed, 40 insertions(+), 19 deletions(-)
tools/testing/cxl/test/mem.c +40 -19
@@ -912,31 +912,52 @@ static struct mock_poison {u64 dpa; } mock_poison_list[MOCK_INJECT_TEST_MAX ]; +static struct cxl_mbox_poison_payload_out +*cxl_get_injected_po (struct cxl_dev_state *cxlds,u64 offset,u64 length) +{ +struct cxl_mbox_poison_payload_out *po; +int nr_records =0 ; +u64 dpa; + + po =kzalloc (struct_size (po, record,MOCK_INJECT_DEV_MAX ),GFP_KERNEL ); +if (!po) +return NULL ; + +for (int i =0 ; i <MOCK_INJECT_TEST_MAX ; i++) { +if (mock_poison_list[i].cxlds != cxlds) +continue ; +if (mock_poison_list[i].dpa < offset || + mock_poison_list[i].dpa > offset + length -1 ) +continue ; + + dpa = mock_poison_list[i].dpa +CXL_POISON_SOURCE_INJECTED ; + po->record[nr_records].address =cpu_to_le64 (dpa); + po->record[nr_records].length =cpu_to_le32 (1 ); + nr_records++; +if (nr_records ==MOCK_INJECT_DEV_MAX ) +break ; + } + +/* Always return count, even when zero */ + po->count =cpu_to_le16 (nr_records); + +return po; +} +static int mock_get_poison (struct cxl_dev_state *cxlds,struct cxl_mbox_cmd *cmd) {struct cxl_mbox_poison_payload_in *pi = cmd->payload_in; +struct cxl_mbox_poison_payload_out *po; +u64 offset =le64_to_cpu (pi->offset); +u64 length =le64_to_cpu (pi->length); +int nr_records; -/* Mock one poison record at pi.offset for 64 bytes */ -struct { -struct cxl_mbox_poison_payload_out po; -struct cxl_poison_record record; - } __packed mock_plist = { - .po = { - .count =cpu_to_le16 (1 ), - }, - .record = { - .length =cpu_to_le32 (1 ), - .address =cpu_to_le64 (le64_to_cpu (pi->offset) + -CXL_POISON_SOURCE_INJECTED ), - }, - }; + po =cxl_get_injected_po (cxlds, offset, length); + nr_records =le16_to_cpu (po->count); +memcpy (cmd->payload_out, po,struct_size (po, record, nr_records)); + cmd->size_out =struct_size (po, record, nr_records); -if (cmd->size_out <sizeof (mock_plist)) -return -EINVAL ; - -memcpy (cmd->payload_out, &mock_plist,sizeof (mock_plist)); - cmd->size_out =sizeof (mock_plist);return 0 ; }
Signature · 1 line
2.37.3
[email protected]
maintainerPATCH v3 6/8 tools/testing/cxl: Add a sysfs attr to test poison injection limits
In reply to [email protected]From: Alison Schofield <[email protected]>
CXL devices may report a maximum number of addresses that a device allows to be poisoned using poison injection. When cxl_test creates mock CXL memory devices, it defaults to MOCK_INJECT_DEV_MAX==88 for all mocked memdevs.
Add a sysfs attribute, poison_inject_max to module cxl_mock_mem so that users can set a custom device injection limit. Fail, and return -EBUSY, if the mock poison list is not empty.
/sys/bus/platform/drivers/cxl_mock_mem/poison_inject_max
A simple usage model is to set the attribute before running a test in order to emulate a device's poison handling.
--- tools/testing/cxl/test/mem.c | 52 +++++++++++++++++++++++++++++++++--- 1 file changed, 48 insertions(+), 4 deletions(-)
tools/testing/cxl/test/mem.c +48 -4
@@ -19,6 +19,8 @@#define MOCK_INJECT_DEV_MAX 8#define MOCK_INJECT_TEST_MAX 128 +static unsigned int poison_inject_dev_max =MOCK_INJECT_DEV_MAX ; +static struct cxl_cel_entry mock_cel[] = { { .opcode =cpu_to_le16 (CXL_MBOX_OP_GET_SUPPORTED_LOGS ),
@@ -485,7 +487,7 @@ static int mock_id(struct cxl_dev_state *cxlds, struct cxl_mbox_cmd *cmd) cpu_to_le64(SZ_256M / CXL_CAPACITY_MULTIPLIER), .total_capacity = cpu_to_le64(DEV_SIZE / CXL_CAPACITY_MULTIPLIER), - .inject_poison_limit =cpu_to_le16 (MOCK_INJECT_DEV_MAX ), + .inject_poison_limit =cpu_to_le16 (MOCK_INJECT_TEST_MAX ), };put_unaligned_le24 (CXL_POISON_LIST_MAX , id.poison_list_max_mer);
@@ -919,7 +921,7 @@ static struct cxl_mbox_poison_payload_outint nr_records =0 ;u64 dpa; - po =kzalloc (struct_size (po, record,MOCK_INJECT_DEV_MAX ),GFP_KERNEL ); + po =kzalloc (struct_size (po, record, poison_inject_dev_max),GFP_KERNEL );if (!po)return NULL ;
@@ -934,7 +936,7 @@ static struct cxl_mbox_poison_payload_out po->record[nr_records].address =cpu_to_le64 (dpa); po->record[nr_records].length =cpu_to_le32 (1 ); nr_records++; -if (nr_records ==MOCK_INJECT_DEV_MAX ) +if (nr_records == poison_inject_dev_max)break ; }
@@ -969,7 +971,7 @@ static bool mock_poison_dev_max_injected(struct cxl_dev_state *cxlds)if (mock_poison_list[i].cxlds == cxlds) count++; } -return (count >=MOCK_INJECT_DEV_MAX ); +return (count >= poison_inject_dev_max); }static bool mock_poison_add (struct cxl_dev_state *cxlds,u64 dpa)
@@ -1051,6 +1053,47 @@ static int mock_clear_poison(struct cxl_dev_state *cxlds,return 0 ; } +static bool mock_poison_list_empty (void ) +{ +for (int i =0 ; i <MOCK_INJECT_TEST_MAX ; i++) { +if (mock_poison_list[i].cxlds) +return false; + } +return true; +} + +static ssize_t poison_inject_max_show (struct device_driver *drv,char *buf) +{ +return sysfs_emit (buf,"%u\n" , poison_inject_dev_max); +} + +static ssize_t poison_inject_max_store (struct device_driver *drv, +const char *buf,size_t len) +{ +int val; + +if (kstrtoint (buf,0 , &val) <0 ) +return -EINVAL ; + +if (!mock_poison_list_empty ()) +return -EBUSY ; + +if (val <=MOCK_INJECT_TEST_MAX ) + poison_inject_dev_max = val; +else +return -EINVAL ; + +return len; +} + +static DRIVER_ATTR_RW (poison_inject_max); + +static struct attribute *cxl_mock_mem_core_attrs[] = { + &driver_attr_poison_inject_max.attr, +NULL +}; +ATTRIBUTE_GROUPS (cxl_mock_mem_core); +static int cxl_mock_mbox_send (struct cxl_dev_state *cxlds,struct cxl_mbox_cmd *cmd) {struct device *dev = cxlds->dev;
@@ -1259,6 +1302,7 @@ static struct platform_driver cxl_mock_mem_driver = { .driver = { .name = KBUILD_MODNAME, .dev_groups = cxl_mock_mem_groups, + .groups = cxl_mock_mem_core_groups, }, };
Signature · 1 line
2.37.3
[email protected]
maintainerPATCH v3 7/8 cxl/memdev: Make inject and clear poison cmds kernel exclusive
In reply to [email protected]From: Alison Schofield <[email protected]>
Inject and clear poison commands are intended to be used in debug mode only, and if improperly used, can lead to data corruption. The kernel provides a sysfs interface that provides the protection needed to issue these commands.[1]
The CXL driver defines Enabled commands in its ABI.[2] Enabled means that the device and the driver both support the command. If a device supports inject and/or clear, those commands are flagged Enabled.
The ABI also defines another command flag: Exclusive. Exclusive commands are reserved for kernel use. The exclusive flags can be temporal, but for inject and clear, the status is permanent.
Document the exclusivity of Inject and Clear in the ABI kernel doc. (Clean up a typo in kdoc too: 'CXL_MEM_COMMAND_FLAG_ENABLED')
Create an exclusive commands bitmap in the memdev driver, add the inject and clear poison commands, and set it in the cxl_dev_state.
[1] Documentation/ABI/testing/sysfs-bus-cxl
[2] include/uapi/linux/cxl_mem.h
--- drivers/cxl/core/memdev.c | 6 ++++++ include/uapi/linux/cxl_mem.h | 21 ++++++++++++++++----- 2 files changed, 22 insertions(+), 5 deletions(-)
drivers/cxl/core/memdev.c +6 -0
@@ -10,6 +10,8 @@static DECLARE_RWSEM (cxl_memdev_rwsem); +static __read_mostly DECLARE_BITMAP(exclusive_cmds, CXL_MEM_COMMAND_ID_MAX); +/* * An entire PCI topology full of devices should be enough for any * config
@@ -571,6 +573,10 @@ struct cxl_memdev *devm_cxl_add_memdev(struct cxl_dev_state *cxlds) cxlmd->cxlds = cxlds; cxlds->cxlmd = cxlmd; +set_bit (CXL_MEM_COMMAND_ID_INJECT_POISON , exclusive_cmds); +set_bit (CXL_MEM_COMMAND_ID_CLEAR_POISON , exclusive_cmds); +set_exclusive_cxl_commands (cxlds, exclusive_cmds); + cdev = &cxlmd->cdev; rc =cdev_device_add (cdev, dev);if (rc)
include/uapi/linux/cxl_mem.h +16 -5
@@ -74,17 +74,28 @@ static const struct {* @id: ID number for the command. * @flags: Flags that specify command behavior. * -* CXL_MEM_COMMAND_FLAG_USER_ENABLED +* CXL_MEM_COMMAND_FLAG_ENABLED * * The given command id is supported by the driver and is supported by * a related opcode on the device. * * CXL_MEM_COMMAND_FLAG_EXCLUSIVE * -* Requests with the given command id will terminate with EBUSY as the -* kernel actively owns management of the given resource. For example, -* the label-storage-area can not be written while the kernel is -* actively managing that space. +* The given command id is for kernel exclusive use and is not +* available to userspace. Requests will terminate with EBUSY. +* +* The exclusive flag may be temporal, and only set while the +* kernel actively owns management of the given resource. For +* example, the label-storage-area can not be written while the +* kernel is actively managing that space. +* +* The exclusive flag can be permanent, as in commands that can +* never be issued through the ioctl interface. +* +* INJECT_POISON and CLEAR_POISON are permanently kernel exclusive. +* They are supported through a sysfs interface that validates the +* safety of each command based on the state of the memdev. +* See: Documentation/ABI/testing/sysfs-bus-cxl * * @size_in: Expected input size, or ~0 if variable length. * @size_out: Expected output size, or ~0 if variable length.
Signature · 1 line
2.37.3
[email protected]
maintainerPATCH v3 8/8 cxl/mbox: Block inject and clear poison opcodes in raw mode
In reply to [email protected]From: Alison Schofield <[email protected]>
Inject and clear poison are commands intended for debug environments, and can cause data corruption if issued without validation. They are kernel exclusive commands not available to userspace through ioctls, but could be submitted via the raw mode ioctl.
Add inject and clear poison to the cxl_disabled_raw_commands[] list. Attempts by userspace to issue either command via the RAW ioctl fail with -EPERM.
--- drivers/cxl/core/mbox.c | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/cxl/core/mbox.c +6 -0
@@ -89,6 +89,10 @@ static struct cxl_mem_command cxl_mem_commands[CXL_MEM_COMMAND_ID_MAX] = {* * CXL_MBOX_OP_[GET_]SCAN_MEDIA: The kernel provides a native error list that * is kept up to date with patrol notifications and error management. +* +* CXL_MBOX_OP_[INJECT|CLEAR]_POISON: The kernel provides a sysfs interface +* to these commands that ensures data protection of mapped resources. +* See: Documentation/ABI/testing/sysfs-bus-cxl */ static u16 cxl_disabled_raw_commands[] = {CXL_MBOX_OP_ACTIVATE_FW ,
@@ -97,6 +101,8 @@ static u16 cxl_disabled_raw_commands[] = {CXL_MBOX_OP_SET_SHUTDOWN_STATE ,CXL_MBOX_OP_SCAN_MEDIA ,CXL_MBOX_OP_GET_SCAN_MEDIA , +CXL_MBOX_OP_INJECT_POISON , + CXL_MBOX_OP_CLEAR_POISON, };/*
Signature · 1 line
2.37.3
Alison Schofield
maintainerRe: [PATCH v3 6/8] tools/testing/cxl: Add a sysfs attr to test poison injection limits
In reply to [email protected]Quoted 5 lines · On Wed, Mar 01, 2023 at 01:36:31PM -0800, [email protected] wrote:
From: Alison Schofield <[email protected]>
CXL devices may report a maximum number of addresses that a device allows to be poisoned using poison injection. When
cxl_testcreates mock CXL memory devices, it defaults to MOCK_INJECT_DEV_MAX==88 for
oops...MOCK_INJECT_DEV_MAX==8 (not 88)
Quoted 26 lines
all mocked memdevs.
Add a sysfs attribute,
poison_inject_maxto modulecxl_mock_memso that users can set a custom device injection limit. Fail, and return-EBUSY, if the mock poison list is not empty.
/sys/bus/platform/drivers/cxl_mock_mem/poison_inject_maxA simple usage model is to set the attribute before running a test in order to emulate a device's poison handling.
Suggested-by Dave Jiang <[email protected]>Signed-off-by Alison Schofield <[email protected]>Reviewed-by Jonathan Cameron <[email protected]>--- tools/testing/cxl/test/mem.c | 52 +++++++++++++++++++++++++++++++++--- 1 file changed, 48 insertions(+), 4 deletions(-)tools/testing/cxl/test/mem.c +0
-0@@ -19,6 +19,8 @@#define MOCK_INJECT_DEV_MAX 8#define MOCK_INJECT_TEST_MAX 128
snip
Re: [PATCH v3 1/8] cxl/memdev: Add support for the Inject Poison mailbox command
In reply to [email protected]Quoted 19 lines · On Wed, 1 Mar 2023 13:36:26 -0800 [email protected] wrote:
From: Alison Schofield <[email protected]>
CXL devices optionally support the INJECT POISON mailbox command. Add a sysfs attribute and memdev driver support for injecting poison. The attribute is only visible for devices supporting the capability when the kernel is built with
CONFIG_CXL_POISON_INJECT.When a Device Physical Address (DPA) is written to the
inject_poisonsysfs attribute, send an inject poison command to the device for the specified address.Per the CXL Specification (3.0 8.2.9.8.4.2), after receiving a valid inject poison request, the device will return poison when the address is accessed through the CXL.mem bus. Injecting poison adds the address to the device's Poison List and the error source is set to Injected. In addition, the device adds a poison creation event to its internal Informational Event log, updates the Event Status register, and if configured, interrupts the host.
Quoted 6 lines
Also, per the CXL Specification, it is not an error to inject poison into an address that already has poison present and no error is returned from the device.
Signed-off-by Alison Schofield <[email protected]>Reviewed-by Jonathan Cameron <[email protected]>
One query inline about the protection against DPAs that are mapped. I'm not sure the checks won't rule out injection on a DPA that is a configured but not yet committed HDM decoder range.
I think we should allow injection into such a memory address as it's not in use.
Quoted 43 lines
--- Documentation/ABI/testing/sysfs-bus-cxl | 22 ++++++ drivers/cxl/Kconfig | 11 +++ drivers/cxl/core/memdev.c | 97 +++++++++++++++++++++++++ drivers/cxl/cxlmem.h | 5 ++ 4 files changed, 135 insertions(+)Documentation/ABI/testing/sysfs-bus-cxl +22
-0@@ -429,3 +429,25 @@ Description: attribute is only visible for devices supporting the capability. The retrieved errors are logged as kernel trace events with the label 'cxl_poison'. + + +What: /sys/bus/cxl/devices/memX/inject_poison +Date: January, 2023 +KernelVersion: v6.3 +Contact: [email protected] +Description: + (WO) When a Device Physical Address (DPA) is written to this + attribute, the memdev driver sends an inject poison command to + the device for the specified address. The DPA must be 64-byte + aligned and the length of the injected poison is 64-bytes. If + successful, the device returns poison when the address is + accessed through the CXL.mem bus. Injecting poison adds the + address to the device's Poison List and the error source is set + to Injected. In addition, the device adds a poison creation + event to its internal Informational Event log, updates the + Event Status register, and if configured, interrupts the host. + It is not an error to inject poison into an address that + already has poison present and no error is returned. The + inject_poison attribute is only visible for devices supporting + the capability. Kconfig option CXL_POISON_INJECT must be on + to enable this option. The default is off.drivers/cxl/Kconfig +0
-0@@ -139,4 +139,15 @@ config CXL_REGION_INVALIDATION_TEST If unsure, or if this kernel is meant for production environments,
drivers/cxl/Kconfig config CXL_REGION_INVALIDATION_TEST · line 149
Quoted 10 lines
drivers/cxl/Kconfig +8
-0say N. +config CXL_POISON_INJECT + bool "CXL: Support CXL Memory Device Poison Inject" + depends on CXL_MEM + help + Selecting this option creates the sysfs attributes inject_poison + and clear_poison for CXL memory devices supporting the capability. + This option is intended for debug scenarios only and is disabled + by default. See Documentation/ABI/testing/sysfs-bus-cxl.
Default for almost everything in Kconfig is off. Is it useful to call that out for this one? The unsure bit below is enough for me.
Quoted 15 lines
drivers/cxl/Kconfig +3
-0+ + If unsure, say N. + endifdrivers/cxl/core/memdev.c +3
-0@@ -165,6 +165,92 @@ static ssize_t trigger_poison_list_store(struct device *dev, }static DEVICE_ATTR_WO (trigger_poison_list); +static int cxl_dpa_mapped (struct device *dev,void *data) +{ +struct cxl_endpoint_decoder *cxled;
drivers/cxl/core/memdev.c static ssize_t trigger_poison_list_store(struct device *dev, · line 180
Quoted 10 lines
drivers/cxl/core/memdev.c +10
-0+u64 *dpa = data; + +if (!is_endpoint_decoder (dev)) +return 0 ; + + cxled =to_cxl_endpoint_decoder (dev); +if (!cxled->dpa_res || !resource_size (cxled->dpa_res)) +return 0 ; + +if (*dpa <= cxled->dpa_res->end && *dpa >= cxled->dpa_res->start) {
I haven't chased it all the way through, but are we guaranteed that this particular decoder is committed if we reach here?
I think the resource is setup when we set size not at point of committing so checking that may not be sufficient.
Quoted 117 lines
drivers/cxl/core/memdev.c +84
-0+dev_dbg (dev,"dpa:0x%llx mapped in region:%s\n" , + *dpa,dev_name (&cxled->cxld.region->dev)); +return 1 ; + } + +return 0 ; +} + +static int cxl_validate_poison_dpa (struct cxl_memdev *cxlmd,u64 dpa) +{ +struct cxl_dev_state *cxlds = cxlmd->cxlds; +struct cxl_port *port; +int rc; + +if (!resource_size (&cxlds->dpa_res)) { +dev_dbg (cxlds->dev,"device has no dpa resource\n" ); +return -EINVAL ; + } +if (dpa < cxlds->dpa_res.start || dpa > cxlds->dpa_res.end) { +dev_dbg (cxlds->dev,"dpa:0x%llx not in resource:%pR\n" , + dpa, &cxlds->dpa_res); +return -EINVAL ; + } +if (!IS_ALIGNED (dpa,64 )) { +dev_dbg (cxlds->dev,"dpa:0x%llx is not 64-byte aligned\n" , dpa); +return -EINVAL ; + } + port =dev_get_drvdata (&cxlmd->dev); +if (port &&is_cxl_endpoint (port) && port->commit_end !=-1 ) { + rc =device_for_each_child (&port->dev, &dpa, cxl_dpa_mapped); +if (rc) +return -EINVAL ; + } + +return 0 ; +} + +static ssize_t inject_poison_store (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t len) +{ +struct cxl_memdev *cxlmd =to_cxl_memdev (dev); +struct cxl_mbox_inject_poison inject; +struct cxl_mbox_cmd mbox_cmd; +u64 dpa; +int rc; + + rc =kstrtou64 (buf,0 , &dpa); +if (rc) +return rc; + +down_read (&cxl_dpa_rwsem); + rc =cxl_validate_poison_dpa (cxlmd, dpa); +if (rc) { +up_read (&cxl_dpa_rwsem); +return rc; + } + + inject = (struct cxl_mbox_inject_poison ) { + .address =cpu_to_le64 (dpa) + }; + mbox_cmd = (struct cxl_mbox_cmd ) { + .opcode =CXL_MBOX_OP_INJECT_POISON , + .size_in =sizeof (inject), + .payload_in = &inject, + }; + rc =cxl_internal_send_cmd (cxlmd->cxlds, &mbox_cmd); + +up_read (&cxl_dpa_rwsem); +return rc ? rc : len; +} +static DEVICE_ATTR_WO (inject_poison); +static struct attribute *cxl_memdev_attributes[] = { &dev_attr_serial.attr, &dev_attr_firmware_version.attr,@@ -172,6 +258,7 @@ static struct attribute *cxl_memdev_attributes[] = { &dev_attr_label_storage_size.attr, &dev_attr_numa_node.attr, &dev_attr_trigger_poison_list.attr, + &dev_attr_inject_poison.attr, NULL, };@@ -198,6 +285,16 @@ static umode_t cxl_memdev_visible(struct kobject *kobj, struct attribute *a, to_cxl_memdev(dev)->cxlds->enabled_cmds))return 0 ; } +if (a == &dev_attr_inject_poison.attr) { +struct device *dev =kobj_to_dev (kobj); + +if (!IS_ENABLED (CONFIG_CXL_POISON_INJECT )) +return 0 ; + +if (!test_bit (CXL_MEM_COMMAND_ID_INJECT_POISON , +to_cxl_memdev (dev)->cxlds->enabled_cmds)) +return 0 ; + }return a->mode; }drivers/cxl/cxlmem.h +5
-0@@ -602,6 +602,11 @@ struct cxl_mbox_poison_payload_out {#define CXL_POISON_SOURCE_INJECTED 3#define CXL_POISON_SOURCE_VENDOR 7 +/* Inject & Clear Poison CXL 3.0 Spec 8.2.9.8.4.2/3 */ +struct cxl_mbox_inject_poison { +__le64 address; +}; +/** * struct cxl_mem_command - Driver representation of a memory device command * @info: Command information as it exists for the UAPI
Re: [PATCH v3 2/8] cxl/memdev: Add support for the Clear Poison mailbox command
In reply to [email protected]Quoted 17 lines · On Wed, 1 Mar 2023 13:36:27 -0800 [email protected] wrote:
From: Alison Schofield <[email protected]>
CXL devices optionally support the CLEAR POISON mailbox command. Add a sysfs attribute and memdev driver support for clearing poison. The attribute is only visible for devices supporting the capability when the kernel is built with
CONFIG_CXL_POISON_INJECT.When a Device Physical Address (DPA) is written to the
clear_poisonsysfs attribute, send a clear poison command to the device for the specified address.Per the CXL Specification (3.0 8.2.9.8.4.3), after receiving a valid clear poison request, the device removes the address from the device's Poison List and writes 0 (zero) for 64 bytes starting at address. If the device cannot clear poison from the address, it returns a permanent media error and
-ENXIOis returned to the user.
Quoted 3 lines
Additionally, and per the spec also, it is not an error to clear poison of an address that is not poisoned. In this case, the device does not overwrite the address and the device does not return an error.
That's not inline with the spec.
"Clear Poison Write Data: The data the device shall always write into the requested physical address, atomically, while clearing poison if the location is marked as being poisoned."
The overwrite always happens whether or not it's poisoned.
Quoted 26 lines
*Implementation note: Although the CXL specification defines the clear command to accept 64 bytes of 'write-data' to be used when clearing the poisoned address, this implementation always uses 0 (zeros) for the write-data.
Signed-off-by Alison Schofield <[email protected]>Reviewed-by Jonathan Cameron <[email protected]>--- Documentation/ABI/testing/sysfs-bus-cxl | 18 ++++++++ drivers/cxl/core/memdev.c | 59 +++++++++++++++++++++++++ drivers/cxl/cxlmem.h | 6 +++ 3 files changed, 83 insertions(+)Documentation/ABI/testing/sysfs-bus-cxl +4
-0@@ -451,3 +451,21 @@ Description: inject_poison attribute is only visible for devices supporting the capability. Kconfig option CXL_POISON_INJECT must be on to enable this option. The default is off. + + +What: /sys/bus/cxl/devices/memX/clear_poison +Date: January, 2023
Documentation/ABI/testing/sysfs-bus-cxl Description: · line 467
Quoted 10 lines
Documentation/ABI/testing/sysfs-bus-cxl +10
-0+KernelVersion: v6.3 +Contact: [email protected] +Description: + (WO) When a Device Physical Address (DPA) is written to this + attribute, the memdev driver sends a clear poison command to + the device for the specified address. Clearing poison removes + the address from the device's Poison List and writes 0 (zero) + for 64 bytes starting at address. It is not an error to clear + poison from an address that does not have poison set, and if + poison was not set, the address is not overwritten. If the
As above.
Quoted 29 lines
Documentation/ABI/testing/sysfs-bus-cxl +4
-0+ device cannot clear poison from the address, -ENXIO is returned. + The clear_poison attribute is only visible for devices + supporting the capability. Kconfig option CXL_POISON_INJECT + must be on to enable this option. The default is off.drivers/cxl/core/memdev.c +17
-0@@ -251,6 +251,53 @@ static ssize_t inject_poison_store(struct device *dev, }static DEVICE_ATTR_WO (inject_poison); +static ssize_t clear_poison_store (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t len) +{ +struct cxl_memdev *cxlmd =to_cxl_memdev (dev); +struct cxl_mbox_clear_poison clear; +struct cxl_mbox_cmd mbox_cmd; +u64 dpa; +int rc; + + rc =kstrtou64 (buf,0 , &dpa); +if (rc) +return rc; + +down_read (&cxl_dpa_rwsem); + rc =cxl_validate_poison_dpa (cxlmd, dpa); +if (rc) {
drivers/cxl/core/memdev.c static ssize_t inject_poison_store(struct device *dev, · line 280
Quoted 10 lines
drivers/cxl/core/memdev.c +10
-0+up_read (&cxl_dpa_rwsem); +return rc; + } + +/* +* In CXL 3.0 Spec 8.2.9.8.4.3, the Clear Poison mailbox command +* is defined to accept 64 bytes of 'write-data', along with the +* address to clear. The device writes the data into the address +* atomically, while clearing poison if the location is marked as +* being poisoned.
This statement is correct in that it says the data is always written whether or not there is poison at the address.
Quoted 66 lines
drivers/cxl/core/memdev.c +32
-0+* +* Always use '0' for the write-data. +*/ + clear = (struct cxl_mbox_clear_poison ) { + .address =cpu_to_le64 (dpa) + }; + + mbox_cmd = (struct cxl_mbox_cmd ) { + .opcode =CXL_MBOX_OP_CLEAR_POISON , + .size_in =sizeof (clear), + .payload_in = &clear, + }; + + rc =cxl_internal_send_cmd (cxlmd->cxlds, &mbox_cmd); + +up_read (&cxl_dpa_rwsem); +return rc ? rc : len; +} +static DEVICE_ATTR_WO (clear_poison); +static struct attribute *cxl_memdev_attributes[] = { &dev_attr_serial.attr, &dev_attr_firmware_version.attr,@@ -259,6 +306,7 @@ static struct attribute *cxl_memdev_attributes[] = { &dev_attr_numa_node.attr, &dev_attr_trigger_poison_list.attr, &dev_attr_inject_poison.attr, + &dev_attr_clear_poison.attr, NULL, };@@ -295,6 +343,17 @@ static umode_t cxl_memdev_visible(struct kobject *kobj, struct attribute *a, to_cxl_memdev(dev)->cxlds->enabled_cmds))return 0 ; } +if (a == &dev_attr_clear_poison.attr) { +struct device *dev =kobj_to_dev (kobj); + +if (!IS_ENABLED (CONFIG_CXL_POISON_INJECT )) +return 0 ; + +if (!test_bit (CXL_MEM_COMMAND_ID_CLEAR_POISON , +to_cxl_memdev (dev)->cxlds->enabled_cmds)) { +return 0 ; + } + }return a->mode; }drivers/cxl/cxlmem.h +6
-0@@ -607,6 +607,12 @@ struct cxl_mbox_inject_poison {__le64 address; }; +/* Clear Poison CXL 3.0 Spec 8.2.9.8.4.3 */ +struct cxl_mbox_clear_poison { +__le64 address; +u8 write_data[CXL_POISON_LEN_MULT ]; +} __packed; +/** * struct cxl_mem_command - Driver representation of a memory device command * @info: Command information as it exists for the UAPI
Re: [PATCH v3 7/8] cxl/memdev: Make inject and clear poison cmds kernel exclusive
In reply to [email protected]Quoted 35 lines · On Wed, 1 Mar 2023 13:36:32 -0800 [email protected] wrote:
From: Alison Schofield <[email protected]>
Inject and clear poison commands are intended to be used in debug mode only, and if improperly used, can lead to data corruption. The kernel provides a sysfs interface that provides the protection needed to issue these commands.[1]
The CXL driver defines Enabled commands in its ABI.[2] Enabled means that the device and the driver both support the command. If a device supports inject and/or clear, those commands are flagged Enabled.
The ABI also defines another command flag: Exclusive. Exclusive commands are reserved for kernel use. The exclusive flags can be temporal, but for inject and clear, the status is permanent.
Document the exclusivity of Inject and Clear in the ABI kernel doc. (Clean up a typo in kdoc too: '
CXL_MEM_COMMAND_FLAG_ENABLED')Create an exclusive commands bitmap in the memdev driver, add the inject and clear poison commands, and set it in the
cxl_dev_state.[1]
Documentation/ABI/testing/sysfs-bus-cxl
[2]include/uapi/linux/cxl_mem.hSigned-off-by Alison Schofield <[email protected]>--- drivers/cxl/core/memdev.c | 6 ++++++ include/uapi/linux/cxl_mem.h | 21 ++++++++++++++++----- 2 files changed, 22 insertions(+), 5 deletions(-)drivers/cxl/core/memdev.c +0
-0
drivers/cxl/core/memdev.c line 13
Quoted 4 lines
drivers/cxl/core/memdev.c +1
-0@@ -10,6 +10,8 @@static DECLARE_RWSEM (cxl_memdev_rwsem); +static __read_mostly DECLARE_BITMAP(exclusive_cmds, CXL_MEM_COMMAND_ID_MAX);
Seems like a macro to wrap up the DECLARE_BITMAP and the length
so that we don't have to be careful these are the correct size might be useful.
Quoted 26 lines
drivers/cxl/core/memdev.c +5
-0+/* * An entire PCI topology full of devices should be enough for any * config @@ -571,6 +573,10 @@ struct cxl_memdev *devm_cxl_add_memdev(struct cxl_dev_state *cxlds) cxlmd->cxlds = cxlds; cxlds->cxlmd = cxlmd; +set_bit (CXL_MEM_COMMAND_ID_INJECT_POISON , exclusive_cmds); +set_bit (CXL_MEM_COMMAND_ID_CLEAR_POISON , exclusive_cmds); +set_exclusive_cxl_commands (cxlds, exclusive_cmds); + cdev = &cxlmd->cdev; rc =cdev_device_add (cdev, dev);if (rc)include/uapi/linux/cxl_mem.h +1
-1@@ -74,17 +74,28 @@ static const struct {* @id: ID number for the command. * @flags: Flags that specify command behavior. * -* CXL_MEM_COMMAND_FLAG_USER_ENABLED +* CXL_MEM_COMMAND_FLAG_ENABLED *
include/uapi/linux/cxl_mem.h static const struct { · line 84
Quoted 10 lines
include/uapi/linux/cxl_mem.h +1
-4* The given command id is supported by the driver and is supported by * a related opcode on the device. * * CXL_MEM_COMMAND_FLAG_EXCLUSIVE * -* Requests with the given command id will terminate with EBUSY as the -* kernel actively owns management of the given resource. For example, -* the label-storage-area can not be written while the kernel is -* actively managing that space. +* The given command id is for kernel exclusive use and is not
I'm guessing tabs and space differences to the above?
Other than those little things LGTM
Quoted 17 lines
include/uapi/linux/cxl_mem.h +14
-0+* available to userspace. Requests will terminate with EBUSY. +* +* The exclusive flag may be temporal, and only set while the +* kernel actively owns management of the given resource. For +* example, the label-storage-area can not be written while the +* kernel is actively managing that space. +* +* The exclusive flag can be permanent, as in commands that can +* never be issued through the ioctl interface. +* +* INJECT_POISON and CLEAR_POISON are permanently kernel exclusive. +* They are supported through a sysfs interface that validates the +* safety of each command based on the state of the memdev. +* See: Documentation/ABI/testing/sysfs-bus-cxl * * @size_in: Expected input size, or ~0 if variable length. * @size_out: Expected output size, or ~0 if variable length.
Re: [PATCH v3 8/8] cxl/mbox: Block inject and clear poison opcodes in raw mode
In reply to [email protected]Quoted 7 lines · On Wed, 1 Mar 2023 13:36:33 -0800 [email protected] wrote:
From: Alison Schofield <[email protected]>
Inject and clear poison are commands intended for debug environments, and can cause data corruption if issued without validation. They are kernel exclusive commands not available to userspace through ioctls, but could be submitted via the raw mode ioctl.
Quoted 5 lines
Add inject and clear poison to the cxl_disabled_raw_commands[] list. Attempts by userspace to issue either command via the RAW ioctl fail with
-EPERM.Signed-off-by Alison Schofield <[email protected]>
Quoted 28 lines
--- drivers/cxl/core/mbox.c | 6 ++++++ 1 file changed, 6 insertions(+)drivers/cxl/core/mbox.c +6
-0@@ -89,6 +89,10 @@ static struct cxl_mem_command cxl_mem_commands[CXL_MEM_COMMAND_ID_MAX] = {* * CXL_MBOX_OP_[GET_]SCAN_MEDIA: The kernel provides a native error list that * is kept up to date with patrol notifications and error management. +* +* CXL_MBOX_OP_[INJECT|CLEAR]_POISON: The kernel provides a sysfs interface +* to these commands that ensures data protection of mapped resources. +* See: Documentation/ABI/testing/sysfs-bus-cxl */ static u16 cxl_disabled_raw_commands[] = {CXL_MBOX_OP_ACTIVATE_FW ,@@ -97,6 +101,8 @@ static u16 cxl_disabled_raw_commands[] = {CXL_MBOX_OP_SET_SHUTDOWN_STATE ,CXL_MBOX_OP_SCAN_MEDIA ,CXL_MBOX_OP_GET_SCAN_MEDIA , +CXL_MBOX_OP_INJECT_POISON , + CXL_MBOX_OP_CLEAR_POISON, };/*
Re: [PATCH v3 1/8] cxl/memdev: Add support for the Inject Poison mailbox command
In reply to Jonathan CameronQuoted 26 lines · On Thu, 30 Mar 2023 19:13:35 +0100 Jonathan Cameron…
Quoted 23 lines · On Wed, 1 Mar 2023 13:36:26 -0800 [email protected] wrote:
From: Alison Schofield <[email protected]>
CXL devices optionally support the INJECT POISON mailbox command. Add a sysfs attribute and memdev driver support for injecting poison. The attribute is only visible for devices supporting the capability when the kernel is built with
CONFIG_CXL_POISON_INJECT.When a Device Physical Address (DPA) is written to the
inject_poisonsysfs attribute, send an inject poison command to the device for the specified address.Per the CXL Specification (3.0 8.2.9.8.4.2), after receiving a valid inject poison request, the device will return poison when the address is accessed through the CXL.mem bus. Injecting poison adds the address to the device's Poison List and the error source is set to Injected. In addition, the device adds a poison creation event to its internal Informational Event log, updates the Event Status register, and if configured, interrupts the host.
Also, per the CXL Specification, it is not an error to inject poison into an address that already has poison present and no error is returned from the device.
Quoted 8 lines
Quoted 2 lines
Signed-off-by Alison Schofield <[email protected]>Reviewed-by Jonathan Cameron <[email protected]>One query inline about the protection against DPAs that are mapped. I'm not sure the checks won't rule out injection on a DPA that is a configured but not yet committed HDM decoder range.
I think we should allow injection into such a memory address as it's not in use.
Oops. I've managed to find an old version. Ignore these comments, I'll take a look at v5.
Jonathan
Quoted 207 lines
Quoted 44 lines
--- Documentation/ABI/testing/sysfs-bus-cxl | 22 ++++++ drivers/cxl/Kconfig | 11 +++ drivers/cxl/core/memdev.c | 97 +++++++++++++++++++++++++ drivers/cxl/cxlmem.h | 5 ++ 4 files changed, 135 insertions(+)Documentation/ABI/testing/sysfs-bus-cxl +22
-0@@ -429,3 +429,25 @@ Description: attribute is only visible for devices supporting the capability. The retrieved errors are logged as kernel trace events with the label 'cxl_poison'. + + +What: /sys/bus/cxl/devices/memX/inject_poison +Date: January, 2023 +KernelVersion: v6.3 +Contact: [email protected] +Description: + (WO) When a Device Physical Address (DPA) is written to this + attribute, the memdev driver sends an inject poison command to + the device for the specified address. The DPA must be 64-byte + aligned and the length of the injected poison is 64-bytes. If + successful, the device returns poison when the address is + accessed through the CXL.mem bus. Injecting poison adds the + address to the device's Poison List and the error source is set + to Injected. In addition, the device adds a poison creation + event to its internal Informational Event log, updates the + Event Status register, and if configured, interrupts the host. + It is not an error to inject poison into an address that + already has poison present and no error is returned. The + inject_poison attribute is only visible for devices supporting + the capability. Kconfig option CXL_POISON_INJECT must be on + to enable this option. The default is off.drivers/cxl/Kconfig +0
-0@@ -139,4 +139,15 @@ config CXL_REGION_INVALIDATION_TEST If unsure, or if this kernel is meant for production environments,drivers/cxl/Kconfig config CXL_REGION_INVALIDATION_TEST · line 149
Quoted 10 lines
drivers/cxl/Kconfig +8
-0say N. +config CXL_POISON_INJECT + bool "CXL: Support CXL Memory Device Poison Inject" + depends on CXL_MEM + help + Selecting this option creates the sysfs attributes inject_poison + and clear_poison for CXL memory devices supporting the capability. + This option is intended for debug scenarios only and is disabled + by default. See Documentation/ABI/testing/sysfs-bus-cxl.Default for almost everything in
Kconfigis off. Is it useful to call that out for this one? The unsure bit below is enough for me.Quoted 15 lines
drivers/cxl/Kconfig +3
-0+ + If unsure, say N. + endifdrivers/cxl/core/memdev.c +3
-0@@ -165,6 +165,92 @@ static ssize_t trigger_poison_list_store(struct device *dev, }static DEVICE_ATTR_WO (trigger_poison_list); +static int cxl_dpa_mapped (struct device *dev,void *data) +{ +struct cxl_endpoint_decoder *cxled;drivers/cxl/core/memdev.c static ssize_t trigger_poison_list_store(struct device *dev, · line 180
Quoted 10 lines
drivers/cxl/core/memdev.c +10
-0+u64 *dpa = data; + +if (!is_endpoint_decoder (dev)) +return 0 ; + + cxled =to_cxl_endpoint_decoder (dev); +if (!cxled->dpa_res || !resource_size (cxled->dpa_res)) +return 0 ; + +if (*dpa <= cxled->dpa_res->end && *dpa >= cxled->dpa_res->start) {I haven't chased it all the way through, but are we guaranteed that this particular decoder is committed if we reach here?
I think the resource is setup when we set size not at point of committing so checking that may not be sufficient.Quoted 117 lines
drivers/cxl/core/memdev.c +84
-0+dev_dbg (dev,"dpa:0x%llx mapped in region:%s\n" , + *dpa,dev_name (&cxled->cxld.region->dev)); +return 1 ; + } + +return 0 ; +} + +static int cxl_validate_poison_dpa (struct cxl_memdev *cxlmd,u64 dpa) +{ +struct cxl_dev_state *cxlds = cxlmd->cxlds; +struct cxl_port *port; +int rc; + +if (!resource_size (&cxlds->dpa_res)) { +dev_dbg (cxlds->dev,"device has no dpa resource\n" ); +return -EINVAL ; + } +if (dpa < cxlds->dpa_res.start || dpa > cxlds->dpa_res.end) { +dev_dbg (cxlds->dev,"dpa:0x%llx not in resource:%pR\n" , + dpa, &cxlds->dpa_res); +return -EINVAL ; + } +if (!IS_ALIGNED (dpa,64 )) { +dev_dbg (cxlds->dev,"dpa:0x%llx is not 64-byte aligned\n" , dpa); +return -EINVAL ; + } + port =dev_get_drvdata (&cxlmd->dev); +if (port &&is_cxl_endpoint (port) && port->commit_end !=-1 ) { + rc =device_for_each_child (&port->dev, &dpa, cxl_dpa_mapped); +if (rc) +return -EINVAL ; + } + +return 0 ; +} + +static ssize_t inject_poison_store (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t len) +{ +struct cxl_memdev *cxlmd =to_cxl_memdev (dev); +struct cxl_mbox_inject_poison inject; +struct cxl_mbox_cmd mbox_cmd; +u64 dpa; +int rc; + + rc =kstrtou64 (buf,0 , &dpa); +if (rc) +return rc; + +down_read (&cxl_dpa_rwsem); + rc =cxl_validate_poison_dpa (cxlmd, dpa); +if (rc) { +up_read (&cxl_dpa_rwsem); +return rc; + } + + inject = (struct cxl_mbox_inject_poison ) { + .address =cpu_to_le64 (dpa) + }; + mbox_cmd = (struct cxl_mbox_cmd ) { + .opcode =CXL_MBOX_OP_INJECT_POISON , + .size_in =sizeof (inject), + .payload_in = &inject, + }; + rc =cxl_internal_send_cmd (cxlmd->cxlds, &mbox_cmd); + +up_read (&cxl_dpa_rwsem); +return rc ? rc : len; +} +static DEVICE_ATTR_WO (inject_poison); +static struct attribute *cxl_memdev_attributes[] = { &dev_attr_serial.attr, &dev_attr_firmware_version.attr,@@ -172,6 +258,7 @@ static struct attribute *cxl_memdev_attributes[] = { &dev_attr_label_storage_size.attr, &dev_attr_numa_node.attr, &dev_attr_trigger_poison_list.attr, + &dev_attr_inject_poison.attr, NULL, };@@ -198,6 +285,16 @@ static umode_t cxl_memdev_visible(struct kobject *kobj, struct attribute *a, to_cxl_memdev(dev)->cxlds->enabled_cmds))return 0 ; } +if (a == &dev_attr_inject_poison.attr) { +struct device *dev =kobj_to_dev (kobj); + +if (!IS_ENABLED (CONFIG_CXL_POISON_INJECT )) +return 0 ; + +if (!test_bit (CXL_MEM_COMMAND_ID_INJECT_POISON , +to_cxl_memdev (dev)->cxlds->enabled_cmds)) +return 0 ; + }return a->mode; }drivers/cxl/cxlmem.h +5
-0@@ -602,6 +602,11 @@ struct cxl_mbox_poison_payload_out {#define CXL_POISON_SOURCE_INJECTED 3#define CXL_POISON_SOURCE_VENDOR 7 +/* Inject & Clear Poison CXL 3.0 Spec 8.2.9.8.4.2/3 */ +struct cxl_mbox_inject_poison { +__le64 address; +}; +/** * struct cxl_mem_command - Driver representation of a memory device command * @info: Command information as it exists for the UAPI