Skip to contentSkip to conversation

net: dsa: add support for MT7988

RFC PATCH In review Daniel Golle 2 participants 30 messages Mar 29, 2023

Subsystems (6)
lore
Share & tools
lore

Daniel Golle

author maintainer
#0 lore raw

v3 cover net: dsa: add support for MT7988

The MediaTek MT7988 SoC comes with a built-in switch very similar to previous MT7530 and MT7531. However, the switch address space is mapped into the SoCs memory space rather than being connected via MDIO. Using MMIO simplifies register access and also removes the need for a bus lock, and for that reason also makes interrupt handling more light-weight.

Note that this is different from previous SoCs like MT7621 and MT7623N which also came with an integrated MT7530-like switch which yet had to be accessed via MDIO.

Split-off the part of the driver registering an MDIO driver, then add another module acting as MMIO/platform driver.

Changes since v2:
* split into many small commits to ease review
* introduce helper functions to reduce code duplication
* use helpers for locking to make lock-skipping easier and less ugly to implement.
* add dt-bindings for mediatek,mt7988-switch

Changes since initial RFC:
* use regmap for register access and move register access to bus- specific driver
* move initialization of MT7531 SGMII PCS to MDIO driver

Daniel Golle (15):
net: dsa: mt7530: refactor SGMII PCS creation
net: dsa: mt7530: use unlocked regmap accessors
net: dsa: mt7530: use regmap to access switch register space
net: dsa: mt7530: move SGMII PCS creation to mt7530_probe function
net: dsa: mt7530: introduce mutex helpers
net: dsa: mt7530: move p5_intf_modes() function to mt7530.c
net: dsa: mt7530: introduce mt7530_probe_common helper function
net: dsa: mt7530: introduce mt7530_remove_common helper function
net: dsa: mt7530: split-off common parts from mt7531_setup
net: dsa: mt7530: introduce separate MDIO driver
net: dsa: mt7530: skip locking if MDIO bus isn't present
net: dsa: mt7530: add support for single-chip reset line
net: dsa: mt7530: add support for 10G link modes for CPU port
net: dsa: mt7530: introduce driver for MT7988 built-in switch
dt-bindings: net: dsa: mediatek,mt7530: add mediatek,mt7988-switch

 .../bindings/net/dsa/mediatek,mt7530.yaml     |  26 +-
 MAINTAINERS                                   |   3 +
 drivers/net/dsa/Kconfig                       |  28 +-
 drivers/net/dsa/Makefile                      |   4 +-
 drivers/net/dsa/mt7530-mdio.c                 | 242 ++++++++
 drivers/net/dsa/mt7530-mmio.c                 |  96 ++++
 drivers/net/dsa/mt7530.c                      | 519 +++++++++---------
 drivers/net/dsa/mt7530.h                      |  38 +-
 8 files changed, 653 insertions(+), 303 deletions(-)
 create mode 100644 drivers/net/dsa/mt7530-mdio.c
 create mode 100644 drivers/net/dsa/mt7530-mmio.c

base-commit: 86e2eca4ddedc07d639c44c990e1c220cac3741e

Signature · 1 line
2.39.2
author maintainer
#1 lore raw

RFC PATCH v3 1/15 net: dsa: mt7530: refactor SGMII PCS creation

Instead of macro templates use a dedidated function and allocated regmap_config when creating the regmaps for the pcs-mtk-lynxi instances.
This is in preparation to switching to use unlocked regmap accessors and have regmap's locking API handle locking for us.

---
 drivers/net/dsa/mt7530.c | 74 +++++++++++++++++++++++++++-------------
 1 file changed, 50 insertions(+), 24 deletions(-)
drivers/net/dsa/mt7530.c +50 -24
index a0d99af897ace..9b88ce5cee5bd 100644
@@ -2926,26 +2926,56 @@ static const struct regmap_bus mt7531_regmap_bus = {
 	.reg_update_bits = mt7530_regmap_update_bits,
 };
 
-#define MT7531_PCS_REGMAP_CONFIG(_name, _reg_base) \
-	{				\
-		.name = _name,		\
-		.reg_bits = 16,		\
-		.val_bits = 32,		\
-		.reg_stride = 4,	\
-		.reg_base = _reg_base,	\
-		.max_register = 0x17c,	\
-	}
-
-static const struct regmap_config mt7531_pcs_config[] = {
-	MT7531_PCS_REGMAP_CONFIG("port5", MT7531_SGMII_REG_BASE(5)),
-	MT7531_PCS_REGMAP_CONFIG("port6", MT7531_SGMII_REG_BASE(6)),
-};
+static int
+mt7531_create_sgmii(struct mt7530_priv *priv)
+{
+	struct regmap_config *mt7531_pcs_config[2];
+	struct phylink_pcs *pcs;
+	struct regmap *regmap;
+	int i, ret = 0;
+
+	for (i = 0; i < 2; i++) {
+		mt7531_pcs_config[i] = devm_kzalloc(priv->dev,
+						    sizeof(struct regmap_config),
+						    GFP_KERNEL);
+		if (!mt7531_pcs_config[i]) {
+			ret = -ENOMEM;
+			break;
+		}
+
+		mt7531_pcs_config[i]->name = i ? "port6" : "port5";
+		mt7531_pcs_config[i]->reg_bits = 16;
+		mt7531_pcs_config[i]->val_bits = 32;
+		mt7531_pcs_config[i]->reg_stride = 4;
+		mt7531_pcs_config[i]->reg_base = MT7531_SGMII_REG_BASE(5 + i);
+		mt7531_pcs_config[i]->max_register = 0x17c;
+
+		regmap = devm_regmap_init(priv->dev,
+					  &mt7531_regmap_bus, priv,
+					  mt7531_pcs_config[i]);
+		if (IS_ERR(regmap)) {
+			ret = PTR_ERR(regmap);
+			break;
+		}
+		pcs = mtk_pcs_lynxi_create(priv->dev, regmap,
+					   MT7531_PHYA_CTRL_SIGNAL3, 0);
+		if (!pcs) {
+			ret = -ENXIO;
+			break;
+		}
+		priv->ports[5 + i].sgmii_pcs = pcs;
+	}
+
+	if (ret && i)
+		mtk_pcs_lynxi_destroy(priv->ports[5].sgmii_pcs);
+
+	return ret;
+}
 
 static int
 mt753x_setup(struct dsa_switch *ds)
 {
 	struct mt7530_priv *priv = ds->priv;
-	struct regmap *regmap;
 	int i, ret;
 
 	/* Initialise the PCS devices */
@@ -2967,15 +2997,11 @@ mt753x_setup(struct dsa_switch *ds)
 	if (ret && priv->irq)
 		mt7530_free_irq_common(priv);
 
-	if (priv->id == ID_MT7531)
-		for (i = 0; i < 2; i++) {
-			regmap = devm_regmap_init(ds->dev,
-						  &mt7531_regmap_bus, priv,
-						  &mt7531_pcs_config[i]);
-			priv->ports[5 + i].sgmii_pcs =
-				mtk_pcs_lynxi_create(ds->dev, regmap,
-						     MT7531_PHYA_CTRL_SIGNAL3, 0);
-		}
+	if (priv->id == ID_MT7531) {
+		ret = mt7531_create_sgmii(priv);
+		if (ret && priv->irq)
+			mt7530_free_irq_common(priv);
+	}
 
 	return ret;
 }
Signature · 1 line
2.39.2
author maintainer
#2 lore raw

RFC PATCH v3 2/15 net: dsa: mt7530: use unlocked regmap accessors

In reply to Daniel Golle

Instead of wrapping the locked register accessor functions, use the unlocked variants and add wrappers to let regmap handle the locking. This is a preparation towards being able to always use regmap to access switch registers instead of open-coded accessor functions.

---
 drivers/net/dsa/mt7530.c | 23 ++++++++++++++---------
 1 file changed, 14 insertions(+), 9 deletions(-)
drivers/net/dsa/mt7530.c +14 -9
index 9b88ce5cee5bd..deb0b338b22c2 100644
@@ -2899,7 +2899,7 @@ static int mt7530_regmap_read(void *context, unsigned int reg, unsigned int *val
 {
 	struct mt7530_priv *priv = context;
 
-	*val = mt7530_read(priv, reg);
+	*val = mt7530_mii_read(priv, reg);
 	return 0;
 };
 
@@ -2907,23 +2907,25 @@ static int mt7530_regmap_write(void *context, unsigned int reg, unsigned int val
 {
 	struct mt7530_priv *priv = context;
 
-	mt7530_write(priv, reg, val);
+	mt7530_mii_write(priv, reg, val);
 	return 0;
 };
 
-static int mt7530_regmap_update_bits(void *context, unsigned int reg,
-				     unsigned int mask, unsigned int val)
+static void
+mt7530_mdio_regmap_lock(void *mdio_lock)
 {
-	struct mt7530_priv *priv = context;
+	mutex_lock_nested(mdio_lock, MDIO_MUTEX_NESTED);
+}
 
-	mt7530_rmw(priv, reg, mask, val);
-	return 0;
-};
+static void
+mt7530_mdio_regmap_unlock(void *mdio_lock)
+{
+	mutex_unlock(mdio_lock);
+}
 
 static const struct regmap_bus mt7531_regmap_bus = {
 	.reg_write = mt7530_regmap_write,
 	.reg_read = mt7530_regmap_read,
-	.reg_update_bits = mt7530_regmap_update_bits,
 };
 
 static int
@@ -2949,6 +2951,9 @@ mt7531_create_sgmii(struct mt7530_priv *priv)
 		mt7531_pcs_config[i]->reg_stride = 4;
 		mt7531_pcs_config[i]->reg_base = MT7531_SGMII_REG_BASE(5 + i);
 		mt7531_pcs_config[i]->max_register = 0x17c;
+		mt7531_pcs_config[i]->lock = mt7530_mdio_regmap_lock;
+		mt7531_pcs_config[i]->unlock = mt7530_mdio_regmap_unlock;
+		mt7531_pcs_config[i]->lock_arg = &priv->bus->mdio_lock;
 
 		regmap = devm_regmap_init(priv->dev,
 					  &mt7531_regmap_bus, priv,
Signature · 1 line
2.39.2
author maintainer
#3 lore raw

RFC PATCH v3 3/15 net: dsa: mt7530: use regmap to access switch register space

In reply to Daniel Golle

Use regmap API to access the switch register space.

---
 drivers/net/dsa/mt7530.c | 88 +++++++++++++++++++++++++---------------
 drivers/net/dsa/mt7530.h |  2 +
 2 files changed, 58 insertions(+), 32 deletions(-)
drivers/net/dsa/mt7530.c +56 -32
index deb0b338b22c2..fffeac8d34855 100644
@@ -183,9 +183,9 @@ core_clear(struct mt7530_priv *priv, u32 reg, u32 val)
 }
 
 static int
-mt7530_mii_write(struct mt7530_priv *priv, u32 reg, u32 val)
+mt7530_regmap_write(void *context, unsigned int reg, unsigned int val)
 {
-	struct mii_bus *bus = priv->bus;
+	struct mii_bus *bus = context;
 	u16 page, r, lo, hi;
 	int ret;
 
@@ -197,24 +197,33 @@ mt7530_mii_write(struct mt7530_priv *priv, u32 reg, u32 val)
 	/* MT7530 uses 31 as the pseudo port */
 	ret = bus->write(bus, 0x1f, 0x1f, page);
 	if (ret < 0)
-		goto err;
+		return ret;
 
 	ret = bus->write(bus, 0x1f, r,  lo);
 	if (ret < 0)
-		goto err;
+		return ret;
 
 	ret = bus->write(bus, 0x1f, 0x10, hi);
-err:
+	return ret;
+}
+
+static int
+mt7530_mii_write(struct mt7530_priv *priv, u32 reg, u32 val)
+{
+	int ret;
+
+	ret = regmap_write(priv->regmap, reg, val);
+
 	if (ret < 0)
-		dev_err(&bus->dev,
+		dev_err(priv->dev,
 			"failed to write mt7530 register\n");
 	return ret;
 }
 
-static u32
-mt7530_mii_read(struct mt7530_priv *priv, u32 reg)
+static int
+mt7530_regmap_read(void *context, unsigned int reg, unsigned int *val)
 {
-	struct mii_bus *bus = priv->bus;
+	struct mii_bus *bus = context;
 	u16 page, r, lo, hi;
 	int ret;
 
@@ -223,16 +232,31 @@ mt7530_mii_read(struct mt7530_priv *priv, u32 reg)
 
 	/* MT7530 uses 31 as the pseudo port */
 	ret = bus->write(bus, 0x1f, 0x1f, page);
-	if (ret < 0) {
-		dev_err(&bus->dev,
-			"failed to read mt7530 register\n");
+	if (ret < 0)
 		return ret;
-	}
 
 	lo = bus->read(bus, 0x1f, r);
 	hi = bus->read(bus, 0x1f, 0x10);
 
-	return (hi << 16) | (lo & 0xffff);
+	*val = (hi << 16) | (lo & 0xffff);
+
+	return 0;
+}
+
+static u32
+mt7530_mii_read(struct mt7530_priv *priv, u32 reg)
+{
+	int ret;
+	u32 val;
+
+	ret = regmap_read(priv->regmap, reg, &val);
+	if (ret) {
+		dev_err(priv->dev,
+			"failed to read mt7530 register\n");
+		return ret;
+	}
+
+	return val;
 }
 
 static void
@@ -2895,22 +2919,6 @@ static const struct phylink_pcs_ops mt7530_pcs_ops = {
 	.pcs_an_restart = mt7530_pcs_an_restart,
 };
 
-static int mt7530_regmap_read(void *context, unsigned int reg, unsigned int *val)
-{
-	struct mt7530_priv *priv = context;
-
-	*val = mt7530_mii_read(priv, reg);
-	return 0;
-};
-
-static int mt7530_regmap_write(void *context, unsigned int reg, unsigned int val)
-{
-	struct mt7530_priv *priv = context;
-
-	mt7530_mii_write(priv, reg, val);
-	return 0;
-};
-
 static void
 mt7530_mdio_regmap_lock(void *mdio_lock)
 {
@@ -2923,7 +2931,7 @@ mt7530_mdio_regmap_unlock(void *mdio_lock)
 	mutex_unlock(mdio_lock);
 }
 
-static const struct regmap_bus mt7531_regmap_bus = {
+static const struct regmap_bus mt7530_regmap_bus = {
 	.reg_write = mt7530_regmap_write,
 	.reg_read = mt7530_regmap_read,
 };
@@ -2956,7 +2964,7 @@ mt7531_create_sgmii(struct mt7530_priv *priv)
 		mt7531_pcs_config[i]->lock_arg = &priv->bus->mdio_lock;
 
 		regmap = devm_regmap_init(priv->dev,
-					  &mt7531_regmap_bus, priv,
+					  &mt7530_regmap_bus, priv->bus,
 					  mt7531_pcs_config[i]);
 		if (IS_ERR(regmap)) {
 			ret = PTR_ERR(regmap);
@@ -3127,6 +3135,7 @@ MODULE_DEVICE_TABLE(of, mt7530_of_match);
 static int
 mt7530_probe(struct mdio_device *mdiodev)
 {
+	static struct regmap_config *regmap_config;
 	struct mt7530_priv *priv;
 	struct device_node *dn;
 
@@ -3206,6 +3215,21 @@ mt7530_probe(struct mdio_device *mdiodev)
 	mutex_init(&priv->reg_mutex);
 	dev_set_drvdata(&mdiodev->dev, priv);
 
+	regmap_config = devm_kzalloc(&mdiodev->dev, sizeof(*regmap_config),
+				     GFP_KERNEL);
+	if (!regmap_config)
+		return -ENOMEM;
+
+	regmap_config->reg_bits = 16;
+	regmap_config->val_bits = 32;
+	regmap_config->reg_stride = 4;
+	regmap_config->max_register = MT7530_CREV;
+	regmap_config->disable_locking = true;
+	priv->regmap = devm_regmap_init(priv->dev, &mt7530_regmap_bus,
+					priv->bus, regmap_config);
+	if (IS_ERR(priv->regmap))
+		return PTR_ERR(priv->regmap);
+
 	return dsa_register_switch(priv->ds);
 }
 
drivers/net/dsa/mt7530.h +2 -0
index c5d29f3fc1d80..39aaca50961bd 100644
@@ -754,6 +754,7 @@ struct mt753x_info {
  * @dev:		The device pointer
  * @ds:			The pointer to the dsa core structure
  * @bus:		The bus used for the device and built-in PHY
+ * @regmap:		The regmap instance representing all switch registers
  * @rstc:		The pointer to reset control used by MCM
  * @core_pwr:		The power supplied into the core
  * @io_pwr:		The power supplied into the I/O
@@ -774,6 +775,7 @@ struct mt7530_priv {
 	struct device		*dev;
 	struct dsa_switch	*ds;
 	struct mii_bus		*bus;
+	struct regmap		*regmap;
 	struct reset_control	*rstc;
 	struct regulator	*core_pwr;
 	struct regulator	*io_pwr;
Signature · 1 line
2.39.2
author maintainer
#7 lore raw

RFC PATCH v3 4/15 net: dsa: mt7530: move SGMII PCS creation to mt7530_probe function

In reply to Daniel Golle

Move creating the SGMII PCS from mt753x_setup() to the more appropriate mt7530_probe() function.
This is done also in preparation of moving all functions related to MDIO-connected MT753x switches to a separate module.

---
 drivers/net/dsa/mt7530.c | 13 +++++++------
 1 file changed, 7 insertions(+), 6 deletions(-)
drivers/net/dsa/mt7530.c +7 -6
index fffeac8d34855..42c89d4863cd5 100644
@@ -3010,12 +3010,6 @@ mt753x_setup(struct dsa_switch *ds)
 	if (ret && priv->irq)
 		mt7530_free_irq_common(priv);
 
-	if (priv->id == ID_MT7531) {
-		ret = mt7531_create_sgmii(priv);
-		if (ret && priv->irq)
-			mt7530_free_irq_common(priv);
-	}
-
 	return ret;
 }
 
@@ -3138,6 +3132,7 @@ mt7530_probe(struct mdio_device *mdiodev)
 	static struct regmap_config *regmap_config;
 	struct mt7530_priv *priv;
 	struct device_node *dn;
+	int ret;
 
 	dn = mdiodev->dev.of_node;
 
@@ -3230,6 +3225,12 @@ mt7530_probe(struct mdio_device *mdiodev)
 	if (IS_ERR(priv->regmap))
 		return PTR_ERR(priv->regmap);
 
+	if (priv->id == ID_MT7531) {
+		ret = mt7531_create_sgmii(priv);
+		if (ret)
+			return ret;
+	}
+
 	return dsa_register_switch(priv->ds);
 }
 
Signature · 1 line
2.39.2
author maintainer
#8 lore raw

RFC PATCH v3 5/15 net: dsa: mt7530: introduce mutex helpers

In reply to Daniel Golle

As the MDIO bus lock only needs to be involved if actually operating on an MDIO-connected switch we will need to skip locking for built-in switches which are accessed via MMIO.
Create helper functions which simplify that upcoming change.

---
 drivers/net/dsa/mt7530.c | 72 ++++++++++++++++++++--------------------
 1 file changed, 36 insertions(+), 36 deletions(-)
drivers/net/dsa/mt7530.c +36 -36
index 42c89d4863cd5..033e70b42b12a 100644
@@ -143,31 +143,40 @@ core_write_mmd_indirect(struct mt7530_priv *priv, int prtad,
 }
 
 static void
-core_write(struct mt7530_priv *priv, u32 reg, u32 val)
+mt7530_mutex_lock(struct mt7530_priv *priv)
 {
-	struct mii_bus *bus = priv->bus;
+	mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED);
+}
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+static void
+mt7530_mutex_unlock(struct mt7530_priv *priv)
+{
+	mutex_unlock(&priv->bus->mdio_lock);
+}
+
+static void
+core_write(struct mt7530_priv *priv, u32 reg, u32 val)
+{
+	mt7530_mutex_lock(priv);
 
 	core_write_mmd_indirect(priv, reg, MDIO_MMD_VEND2, val);
 
-	mutex_unlock(&bus->mdio_lock);
+	mt7530_mutex_unlock(priv);
 }
 
 static void
 core_rmw(struct mt7530_priv *priv, u32 reg, u32 mask, u32 set)
 {
-	struct mii_bus *bus = priv->bus;
 	u32 val;
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	mt7530_mutex_lock(priv);
 
 	val = core_read_mmd_indirect(priv, reg, MDIO_MMD_VEND2);
 	val &= ~mask;
 	val |= set;
 	core_write_mmd_indirect(priv, reg, MDIO_MMD_VEND2, val);
 
-	mutex_unlock(&bus->mdio_lock);
+	mt7530_mutex_unlock(priv);
 }
 
 static void
@@ -262,13 +271,11 @@ mt7530_mii_read(struct mt7530_priv *priv, u32 reg)
 static void
 mt7530_write(struct mt7530_priv *priv, u32 reg, u32 val)
 {
-	struct mii_bus *bus = priv->bus;
-
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	mt7530_mutex_lock(priv);
 
 	mt7530_mii_write(priv, reg, val);
 
-	mutex_unlock(&bus->mdio_lock);
+	mt7530_mutex_unlock(priv);
 }
 
 static u32
@@ -280,14 +287,13 @@ _mt7530_unlocked_read(struct mt7530_dummy_poll *p)
 static u32
 _mt7530_read(struct mt7530_dummy_poll *p)
 {
-	struct mii_bus		*bus = p->priv->bus;
 	u32 val;
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	mt7530_mutex_lock(p->priv);
 
 	val = mt7530_mii_read(p->priv, p->reg);
 
-	mutex_unlock(&bus->mdio_lock);
+	mt7530_mutex_unlock(p->priv);
 
 	return val;
 }
@@ -305,17 +311,16 @@ static void
 mt7530_rmw(struct mt7530_priv *priv, u32 reg,
 	   u32 mask, u32 set)
 {
-	struct mii_bus *bus = priv->bus;
 	u32 val;
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	mt7530_mutex_lock(priv);
 
 	val = mt7530_mii_read(priv, reg);
 	val &= ~mask;
 	val |= set;
 	mt7530_mii_write(priv, reg, val);
 
-	mutex_unlock(&bus->mdio_lock);
+	mt7530_mutex_unlock(priv);
 }
 
 static void
@@ -659,14 +664,13 @@ static int
 mt7531_ind_c45_phy_read(struct mt7530_priv *priv, int port, int devad,
 			int regnum)
 {
-	struct mii_bus *bus = priv->bus;
 	struct mt7530_dummy_poll p;
 	u32 reg, val;
 	int ret;
 
 	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	mt7530_mutex_lock(priv);
 
 	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
 				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
@@ -699,7 +703,7 @@ mt7531_ind_c45_phy_read(struct mt7530_priv *priv, int port, int devad,
 
 	ret = val & MT7531_MDIO_RW_DATA_MASK;
 out:
-	mutex_unlock(&bus->mdio_lock);
+	mt7530_mutex_unlock(priv);
 
 	return ret;
 }
@@ -708,14 +712,13 @@ static int
 mt7531_ind_c45_phy_write(struct mt7530_priv *priv, int port, int devad,
 			 int regnum, u16 data)
 {
-	struct mii_bus *bus = priv->bus;
 	struct mt7530_dummy_poll p;
 	u32 val, reg;
 	int ret;
 
 	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	mt7530_mutex_lock(priv);
 
 	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
 				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
@@ -747,7 +750,7 @@ mt7531_ind_c45_phy_write(struct mt7530_priv *priv, int port, int devad,
 	}
 
 out:
-	mutex_unlock(&bus->mdio_lock);
+	mt7530_mutex_unlock(priv);
 
 	return ret;
 }
@@ -755,14 +758,13 @@ mt7531_ind_c45_phy_write(struct mt7530_priv *priv, int port, int devad,
 static int
 mt7531_ind_c22_phy_read(struct mt7530_priv *priv, int port, int regnum)
 {
-	struct mii_bus *bus = priv->bus;
 	struct mt7530_dummy_poll p;
 	int ret;
 	u32 val;
 
 	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	mt7530_mutex_lock(priv);
 
 	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
 				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
@@ -785,7 +787,7 @@ mt7531_ind_c22_phy_read(struct mt7530_priv *priv, int port, int regnum)
 
 	ret = val & MT7531_MDIO_RW_DATA_MASK;
 out:
-	mutex_unlock(&bus->mdio_lock);
+	mt7530_mutex_unlock(priv);
 
 	return ret;
 }
@@ -794,14 +796,13 @@ static int
 mt7531_ind_c22_phy_write(struct mt7530_priv *priv, int port, int regnum,
 			 u16 data)
 {
-	struct mii_bus *bus = priv->bus;
 	struct mt7530_dummy_poll p;
 	int ret;
 	u32 reg;
 
 	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	mt7530_mutex_lock(priv);
 
 	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, reg,
 				 !(reg & MT7531_PHY_ACS_ST), 20, 100000);
@@ -823,7 +824,7 @@ mt7531_ind_c22_phy_write(struct mt7530_priv *priv, int port, int regnum,
 	}
 
 out:
-	mutex_unlock(&bus->mdio_lock);
+	mt7530_mutex_unlock(priv);
 
 	return ret;
 }
@@ -1104,7 +1105,6 @@ static int
 mt7530_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 {
 	struct mt7530_priv *priv = ds->priv;
-	struct mii_bus *bus = priv->bus;
 	int length;
 	u32 val;
 
@@ -1115,7 +1115,7 @@ mt7530_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 	if (!dsa_is_cpu_port(ds, port))
 		return 0;
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	mt7530_mutex_lock(priv);
 
 	val = mt7530_mii_read(priv, MT7530_GMACCR);
 	val &= ~MAX_RX_PKT_LEN_MASK;
@@ -1136,7 +1136,7 @@ mt7530_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 
 	mt7530_mii_write(priv, MT7530_GMACCR, val);
 
-	mutex_unlock(&bus->mdio_lock);
+	mt7530_mutex_unlock(priv);
 
 	return 0;
 }
@@ -1937,10 +1937,10 @@ mt7530_irq_thread_fn(int irq, void *dev_id)
 	u32 val;
 	int p;
 
-	mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED);
+	mt7530_mutex_lock(priv);
 	val = mt7530_mii_read(priv, MT7530_SYS_INT_STS);
 	mt7530_mii_write(priv, MT7530_SYS_INT_STS, val);
-	mutex_unlock(&priv->bus->mdio_lock);
+	mt7530_mutex_unlock(priv);
 
 	for (p = 0; p < MT7530_NUM_PHYS; p++) {
 		if (BIT(p) & val) {
@@ -1976,7 +1976,7 @@ mt7530_irq_bus_lock(struct irq_data *d)
 {
 	struct mt7530_priv *priv = irq_data_get_irq_chip_data(d);
 
-	mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED);
+	mt7530_mutex_lock(priv);
 }
 
 static void
@@ -1985,7 +1985,7 @@ mt7530_irq_bus_sync_unlock(struct irq_data *d)
 	struct mt7530_priv *priv = irq_data_get_irq_chip_data(d);
 
 	mt7530_mii_write(priv, MT7530_SYS_INT_EN, priv->irq_enable);
-	mutex_unlock(&priv->bus->mdio_lock);
+	mt7530_mutex_unlock(priv);
 }
 
 static struct irq_chip mt7530_irq_chip = {
Signature · 1 line
2.39.2
author maintainer
#10 lore raw

RFC PATCH v3 6/15 net: dsa: mt7530: move p5_intf_modes() function to mt7530.c

In reply to Daniel Golle

In preparation of splitting mt7530.c into a driver for MDIO-connected as well as MDIO-accessed built-in switches on one hand and MMIO-accessed built-in switches move the p5_inft_modes() function from mt7530.h to mt7530.c. The function is only needed there and will trigger a compiler warning about a defined but unused function otherwise when including mt7530.h in the to-be-introduced bus-specific drivers.

---
 drivers/net/dsa/mt7530.c | 18 ++++++++++++++++++
 drivers/net/dsa/mt7530.h | 18 ------------------
 2 files changed, 18 insertions(+), 18 deletions(-)
drivers/net/dsa/mt7530.c +18 -0
index 033e70b42b12a..221d56cf9e710 100644
@@ -946,6 +946,24 @@ mt7530_set_ageing_time(struct dsa_switch *ds, unsigned int msecs)
 	return 0;
 }
 
+static const char *p5_intf_modes(unsigned int p5_interface)
+{
+	switch (p5_interface) {
+	case P5_DISABLED:
+		return "DISABLED";
+	case P5_INTF_SEL_PHY_P0:
+		return "PHY P0";
+	case P5_INTF_SEL_PHY_P4:
+		return "PHY P4";
+	case P5_INTF_SEL_GMAC5:
+		return "GMAC5";
+	case P5_INTF_SEL_GMAC5_SGMII:
+		return "GMAC5_SGMII";
+	default:
+		return "unknown";
+	}
+}
+
 static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
 {
 	struct mt7530_priv *priv = ds->priv;
drivers/net/dsa/mt7530.h +0 -18
index 39aaca50961bd..2a611173a7d08 100644
@@ -682,24 +682,6 @@ enum p5_interface_select {
 	P5_INTF_SEL_GMAC5_SGMII,
 };
 
-static const char *p5_intf_modes(unsigned int p5_interface)
-{
-	switch (p5_interface) {
-	case P5_DISABLED:
-		return "DISABLED";
-	case P5_INTF_SEL_PHY_P0:
-		return "PHY P0";
-	case P5_INTF_SEL_PHY_P4:
-		return "PHY P4";
-	case P5_INTF_SEL_GMAC5:
-		return "GMAC5";
-	case P5_INTF_SEL_GMAC5_SGMII:
-		return "GMAC5_SGMII";
-	default:
-		return "unknown";
-	}
-}
-
 struct mt7530_priv;
 
 struct mt753x_pcs {
Signature · 1 line
2.39.2
author maintainer
#12 lore raw

RFC PATCH v3 7/15 net: dsa: mt7530: introduce mt7530_probe_common helper function

In reply to Daniel Golle

Move commonly used parts from mt7530_probe into new mt7530_probe_common helper function which will be used by both, mt7530_probe and the to-be-introduced mt7988_probe.

---
 drivers/net/dsa/mt7530.c | 86 ++++++++++++++++++++++------------------
 1 file changed, 47 insertions(+), 39 deletions(-)
drivers/net/dsa/mt7530.c +47 -39
index 221d56cf9e710..32875762b3d96 100644
@@ -3145,44 +3145,47 @@ static const struct of_device_id mt7530_of_match[] = {
 MODULE_DEVICE_TABLE(of, mt7530_of_match);
 
 static int
-mt7530_probe(struct mdio_device *mdiodev)
+mt7530_probe_common(struct mt7530_priv *priv)
 {
-	static struct regmap_config *regmap_config;
-	struct mt7530_priv *priv;
-	struct device_node *dn;
-	int ret;
-
-	dn = mdiodev->dev.of_node;
-
-	priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
+	struct device *dev = priv->dev;
+	struct device_node *dn = dev->of_node;
 
-	priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL);
+	priv->ds = devm_kzalloc(dev, sizeof(*priv->ds), GFP_KERNEL);
 	if (!priv->ds)
 		return -ENOMEM;
 
-	priv->ds->dev = &mdiodev->dev;
+	priv->ds->dev = dev;
 	priv->ds->num_ports = MT7530_NUM_PORTS;
 
 	/* Use medatek,mcm property to distinguish hardware type that would
-	 * casues a little bit differences on power-on sequence.
+	 * cause a little bit differences on power-on sequence.
+	 * Note MCM that indicates switch works as the remote standalone
+	 * integrated circuit so the GPIO pin would be used to complete
+	 * the reset, otherwise memory-mapped register accessing used
+	 * through syscon provides in the case of MCM.
 	 */
 	priv->mcm = of_property_read_bool(dn, "mediatek,mcm");
 	if (priv->mcm) {
-		dev_info(&mdiodev->dev, "MT7530 adapts as multi-chip module\n");
+		dev_dbg(dev, "MT7530 adapts as multi-chip module\n");
 
-		priv->rstc = devm_reset_control_get(&mdiodev->dev, "mcm");
+		priv->rstc = devm_reset_control_get(dev, "mcm");
 		if (IS_ERR(priv->rstc)) {
-			dev_err(&mdiodev->dev, "Couldn't get our reset line\n");
+			dev_err(dev, "Couldn't get our reset line\n");
 			return PTR_ERR(priv->rstc);
 		}
+	} else {
+		priv->reset = devm_gpiod_get_optional(dev, "reset",
+						      GPIOD_OUT_LOW);
+		if (IS_ERR(priv->reset)) {
+			dev_err(dev, "Couldn't get our reset line\n");
+			return PTR_ERR(priv->reset);
+		}
 	}
 
 	/* Get the hardware identifier from the devicetree node.
 	 * We will need it for some of the clock and regulator setup.
 	 */
-	priv->info = of_device_get_match_data(&mdiodev->dev);
+	priv->info = of_device_get_match_data(dev);
 	if (!priv->info)
 		return -EINVAL;
 
@@ -3196,6 +3199,32 @@ mt7530_probe(struct mdio_device *mdiodev)
 		return -EINVAL;
 
 	priv->id = priv->info->id;
+	priv->dev = dev;
+	priv->ds->priv = priv;
+	priv->ds->ops = &mt7530_switch_ops;
+	mutex_init(&priv->reg_mutex);
+	dev_set_drvdata(dev, priv);
+
+	return 0;
+}
+
+static int
+mt7530_probe(struct mdio_device *mdiodev)
+{
+	static struct regmap_config *regmap_config;
+	struct mt7530_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->bus = mdiodev->bus;
+	priv->dev = &mdiodev->dev;
+
+	ret = mt7530_probe_common(priv);
+	if (ret)
+		return ret;
 
 	if (priv->id == ID_MT7530) {
 		priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core");
@@ -3207,27 +3236,6 @@ mt7530_probe(struct mdio_device *mdiodev)
 			return PTR_ERR(priv->io_pwr);
 	}
 
-	/* Not MCM that indicates switch works as the remote standalone
-	 * integrated circuit so the GPIO pin would be used to complete
-	 * the reset, otherwise memory-mapped register accessing used
-	 * through syscon provides in the case of MCM.
-	 */
-	if (!priv->mcm) {
-		priv->reset = devm_gpiod_get_optional(&mdiodev->dev, "reset",
-						      GPIOD_OUT_LOW);
-		if (IS_ERR(priv->reset)) {
-			dev_err(&mdiodev->dev, "Couldn't get our reset line\n");
-			return PTR_ERR(priv->reset);
-		}
-	}
-
-	priv->bus = mdiodev->bus;
-	priv->dev = &mdiodev->dev;
-	priv->ds->priv = priv;
-	priv->ds->ops = &mt7530_switch_ops;
-	mutex_init(&priv->reg_mutex);
-	dev_set_drvdata(&mdiodev->dev, priv);
-
 	regmap_config = devm_kzalloc(&mdiodev->dev, sizeof(*regmap_config),
 				     GFP_KERNEL);
 	if (!regmap_config)
Signature · 1 line
2.39.2
author maintainer
#14 lore raw

RFC PATCH v3 8/15 net: dsa: mt7530: introduce mt7530_remove_common helper function

In reply to Daniel Golle

Move commonly used parts from mt7530_remove into new mt7530_remove_common helper function which will be used by both, mt7530_remove and the to-be-introduced mt7988_remove.

---
 drivers/net/dsa/mt7530.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)
drivers/net/dsa/mt7530.c +12 -6
index 32875762b3d96..f84cbd251d1c1 100644
@@ -3260,6 +3260,17 @@ mt7530_probe(struct mdio_device *mdiodev)
 	return dsa_register_switch(priv->ds);
 }
 
+static void
+mt7530_remove_common(struct mt7530_priv *priv)
+{
+	if (priv->irq)
+		mt7530_free_irq(priv);
+
+	dsa_unregister_switch(priv->ds);
+
+	mutex_destroy(&priv->reg_mutex);
+}
+
 static void
 mt7530_remove(struct mdio_device *mdiodev)
 {
@@ -3279,15 +3290,10 @@ mt7530_remove(struct mdio_device *mdiodev)
 		dev_err(priv->dev, "Failed to disable io pwr: %d\n",
 			ret);
 
-	if (priv->irq)
-		mt7530_free_irq(priv);
-
-	dsa_unregister_switch(priv->ds);
+	mt7530_remove_common(priv);
 
 	for (i = 0; i < 2; ++i)
 		mtk_pcs_lynxi_destroy(priv->ports[5 + i].sgmii_pcs);
-
-	mutex_destroy(&priv->reg_mutex);
 }
 
 static void mt7530_shutdown(struct mdio_device *mdiodev)
Signature · 1 line
2.39.2
author maintainer
#16 lore raw

RFC PATCH v3 9/15 net: dsa: mt7530: split-off common parts from mt7531_setup

In reply to Daniel Golle

MT7988 shares a significant part of the setup function with MT7531. Split-off those parts into a shared function which is going to be used also by mt7988_setup.

---
 drivers/net/dsa/mt7530.c | 99 ++++++++++++++++++++++------------------
 1 file changed, 55 insertions(+), 44 deletions(-)
drivers/net/dsa/mt7530.c +55 -44
index f84cbd251d1c1..c9b6b11273683 100644
@@ -2350,12 +2350,65 @@ mt7530_setup(struct dsa_switch *ds)
 	return 0;
 }
 
+static int
+mt7531_setup_common(struct dsa_switch *ds)
+{
+	struct mt7530_priv *priv = ds->priv;
+	struct dsa_port *cpu_dp;
+	int ret, i;
+
+	/* BPDU to CPU port */
+	dsa_switch_for_each_cpu_port(cpu_dp, ds) {
+		mt7530_rmw(priv, MT7531_CFC, MT7531_CPU_PMAP_MASK,
+			   BIT(cpu_dp->index));
+		break;
+	}
+	mt7530_rmw(priv, MT753X_BPC, MT753X_BPDU_PORT_FW_MASK,
+		   MT753X_BPDU_CPU_ONLY);
+
+	/* Enable and reset MIB counters */
+	mt7530_mib_reset(ds);
+
+	for (i = 0; i < MT7530_NUM_PORTS; i++) {
+		/* Disable forwarding by default on all ports */
+		mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
+			   PCR_MATRIX_CLR);
+
+		/* Disable learning by default on all ports */
+		mt7530_set(priv, MT7530_PSC_P(i), SA_DIS);
+
+		mt7530_set(priv, MT7531_DBG_CNT(i), MT7531_DIS_CLR);
+
+		if (dsa_is_cpu_port(ds, i)) {
+			ret = mt753x_cpu_port_enable(ds, i);
+			if (ret)
+				return ret;
+		} else {
+			mt7530_port_disable(ds, i);
+
+			/* Set default PVID to 0 on all user ports */
+			mt7530_rmw(priv, MT7530_PPBV1_P(i), G0_PORT_VID_MASK,
+				   G0_PORT_VID_DEF);
+		}
+
+		/* Enable consistent egress tag */
+		mt7530_rmw(priv, MT7530_PVC_P(i), PVC_EG_TAG_MASK,
+			   PVC_EG_TAG(MT7530_VLAN_EG_CONSISTENT));
+	}
+
+	/* Flush the FDB table */
+	ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
 static int
 mt7531_setup(struct dsa_switch *ds)
 {
 	struct mt7530_priv *priv = ds->priv;
 	struct mt7530_dummy_poll p;
-	struct dsa_port *cpu_dp;
 	u32 val, id;
 	int ret, i;
 
@@ -2433,44 +2486,7 @@ mt7531_setup(struct dsa_switch *ds)
 	mt7531_ind_c45_phy_write(priv, MT753X_CTRL_PHY_ADDR, MDIO_MMD_VEND2,
 				 CORE_PLL_GROUP4, val);
 
-	/* BPDU to CPU port */
-	dsa_switch_for_each_cpu_port(cpu_dp, ds) {
-		mt7530_rmw(priv, MT7531_CFC, MT7531_CPU_PMAP_MASK,
-			   BIT(cpu_dp->index));
-		break;
-	}
-	mt7530_rmw(priv, MT753X_BPC, MT753X_BPDU_PORT_FW_MASK,
-		   MT753X_BPDU_CPU_ONLY);
-
-	/* Enable and reset MIB counters */
-	mt7530_mib_reset(ds);
-
-	for (i = 0; i < MT7530_NUM_PORTS; i++) {
-		/* Disable forwarding by default on all ports */
-		mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
-			   PCR_MATRIX_CLR);
-
-		/* Disable learning by default on all ports */
-		mt7530_set(priv, MT7530_PSC_P(i), SA_DIS);
-
-		mt7530_set(priv, MT7531_DBG_CNT(i), MT7531_DIS_CLR);
-
-		if (dsa_is_cpu_port(ds, i)) {
-			ret = mt753x_cpu_port_enable(ds, i);
-			if (ret)
-				return ret;
-		} else {
-			mt7530_port_disable(ds, i);
-
-			/* Set default PVID to 0 on all user ports */
-			mt7530_rmw(priv, MT7530_PPBV1_P(i), G0_PORT_VID_MASK,
-				   G0_PORT_VID_DEF);
-		}
-
-		/* Enable consistent egress tag */
-		mt7530_rmw(priv, MT7530_PVC_P(i), PVC_EG_TAG_MASK,
-			   PVC_EG_TAG(MT7530_VLAN_EG_CONSISTENT));
-	}
+	mt7531_setup_common(ds);
 
 	/* Setup VLAN ID 0 for VLAN-unaware bridges */
 	ret = mt7530_setup_vlan0(priv);
@@ -2480,11 +2496,6 @@ mt7531_setup(struct dsa_switch *ds)
 	ds->assisted_learning_on_cpu_port = true;
 	ds->mtu_enforcement_ingress = true;
 
-	/* Flush the FDB table */
-	ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
-	if (ret < 0)
-		return ret;
-
 	return 0;
 }
 
Signature · 1 line
2.39.2
author maintainer
#18 lore raw

RFC PATCH v3 10/15 net: dsa: mt7530: introduce separate MDIO driver

In reply to Daniel Golle

Split MT7530 switch driver into a common part and a part specific for MDIO connected switches and multi-chip modules.
Move MDIO-specific functions to newly introduced mt7530-mdio.c while keeping the common parts in mt7530.c.
In order to maintain compatibility with existing kernel configurations keep CONFIG_NET_DSA_MT7530 as symbol to select the MDIO-specific driver while the newly introduced hidden symbol CONFIG_NET_DSA_MT7530_COMMON is selected by CONFIG_NET_DSA_MT7530.

---
 MAINTAINERS                   |   1 +
 drivers/net/dsa/Kconfig       |  16 ++-
 drivers/net/dsa/Makefile      |   3 +-
 drivers/net/dsa/mt7530-mdio.c | 242 ++++++++++++++++++++++++++++++++++
 drivers/net/dsa/mt7530.c      | 235 ++-------------------------------
 drivers/net/dsa/mt7530.h      |   6 +
 6 files changed, 271 insertions(+), 232 deletions(-)
 create mode 100644 drivers/net/dsa/mt7530-mdio.c
MAINTAINERS +1 -0
index fbbda4671e734..7feb52d9ae0b9 100644
@@ -13176,6 +13176,7 @@ M:	Landen Chao <[email protected]>
 M:	DENG Qingfang <[email protected]>
 L:	[email protected]
 S:	Maintained
+F:	drivers/net/dsa/mt7530-mdio.c
 F:	drivers/net/dsa/mt7530.*
 F:	net/dsa/tag_mtk.c
 
drivers/net/dsa/Kconfig +12 -4
index 6b45fa8b69078..c2551b13324c2 100644
@@ -34,15 +34,23 @@ config NET_DSA_LANTIQ_GSWIP
 	  This enables support for the Lantiq / Intel GSWIP 2.1 found in
 	  the xrx200 / VR9 SoC.
 
-config NET_DSA_MT7530
-	tristate "MediaTek MT7530 and MT7531 Ethernet switch support"
+config NET_DSA_MT7530_COMMON
+	tristate
 	select NET_DSA_TAG_MTK
 	select MEDIATEK_GE_PHY
+	help
+	  This enables support for the common parts of MediaTek Ethernet
+	  switch chips.
+
+config NET_DSA_MT7530
+	tristate "MediaTek MT7530 and MT7531 Ethernet switch support"
+	select NET_DSA_MT7530_COMMON
 	select PCS_MTK_LYNXI
 	help
 	  This enables support for the MediaTek MT7530 and MT7531 Ethernet
-	  switch chips. Multi-chip module MT7530 in MT7621AT, MT7621DAT,
-	  MT7621ST and MT7623AI SoCs is supported.
+	  switch chips which are connected via MDIO.
+	  Multi-chip module MT7530 in MT7621AT, MT7621DAT, MT7621ST and
+	  MT7623AI SoCs is supported as well.
 
 config NET_DSA_MV88E6060
 	tristate "Marvell 88E6060 ethernet switch chip support"
drivers/net/dsa/Makefile +2 -1
index 16eb879e0cb4d..71250d7dd41af 100644
@@ -6,7 +6,8 @@ ifdef CONFIG_NET_DSA_LOOP
 obj-$(CONFIG_FIXED_PHY)		+= dsa_loop_bdinfo.o
 endif
 obj-$(CONFIG_NET_DSA_LANTIQ_GSWIP) += lantiq_gswip.o
-obj-$(CONFIG_NET_DSA_MT7530)	+= mt7530.o
+obj-$(CONFIG_NET_DSA_MT7530_COMMON) += mt7530.o
+obj-$(CONFIG_NET_DSA_MT7530)	+= mt7530-mdio.o
 obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
 obj-$(CONFIG_NET_DSA_RZN1_A5PSW) += rzn1_a5psw.o
 obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
drivers/net/dsa/mt7530-mdio.c new file +242 -0

242 lines not on this page · raw message

drivers/net/dsa/mt7530.c +8 -227

286 lines not on this page · raw message

drivers/net/dsa/mt7530.h +6 -0
index 2a611173a7d08..ce02aa592a7a8 100644
@@ -814,4 +814,10 @@ static inline void INIT_MT7530_DUMMY_POLL(struct mt7530_dummy_poll *p,
 	p->reg = reg;
 }
 
+int mt7530_probe_common(struct mt7530_priv *priv);
+void mt7530_remove_common(struct mt7530_priv *priv);
+
+extern const struct dsa_switch_ops mt7530_switch_ops;
+extern const struct mt753x_info mt753x_table[];
+
 #endif /* __MT7530_H */
Signature · 1 line
2.39.2
author maintainer
#20 lore raw

RFC PATCH v3 11/15 net: dsa: mt7530: skip locking if MDIO bus isn't present

In reply to Daniel Golle

As MT7530 and MT7531 internally use 32-bit wide registers, each access to any register of the switch requires several operations on the MDIO bus. Hence if there is congruent access, e.g. due to PCS or PHY polling, this can mess up and interfere with another ongoing register access sequence.

However, the MDIO bus mutex is only relevant for MDIO-connected switches. Prepare switches which have there registers directly mapped into the SoCs register space via MMIO which do not require such locking. There we can simply use regmap's default locking mechanism.

Hence guard mutex operations to only be performed in case of MDIO connected switches.

---
 drivers/net/dsa/mt7530.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/net/dsa/mt7530.c +4 -2
index ce2665abaaf57..c6fad2d156160 100644
@@ -145,13 +145,15 @@ core_write_mmd_indirect(struct mt7530_priv *priv, int prtad,
 static void
 mt7530_mutex_lock(struct mt7530_priv *priv)
 {
-	mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED);
+	if (priv->bus)
+		mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED);
 }
 
 static void
 mt7530_mutex_unlock(struct mt7530_priv *priv)
 {
-	mutex_unlock(&priv->bus->mdio_lock);
+	if (priv->bus)
+		mutex_unlock(&priv->bus->mdio_lock);
 }
 
 static void
Signature · 1 line
2.39.2
author maintainer
#22 lore raw

RFC PATCH v3 12/15 net: dsa: mt7530: add support for single-chip reset line

In reply to Daniel Golle

Similar to multi-chip-module MT7530 also MT7988 uses an internal reset line instead of using an optional reset GPIO like it is the case for external MT7530 and MT7531 ICs.
Add support for internal but non-MCM reset line in preparation for adding support for MT7988.

---
 drivers/net/dsa/mt7530.c | 6 ++++++
 1 file changed, 6 insertions(+)
drivers/net/dsa/mt7530.c +6 -0
index c6fad2d156160..fd55ddc2d1eb3 100644
@@ -3066,6 +3066,12 @@ mt7530_probe_common(struct mt7530_priv *priv)
 			dev_err(dev, "Couldn't get our reset line\n");
 			return PTR_ERR(priv->rstc);
 		}
+	} else if (!priv->bus) {
+		priv->rstc = devm_reset_control_get(dev, NULL);
+		if (IS_ERR(priv->rstc)) {
+			dev_err(dev, "Couldn't get our reset line\n");
+			return PTR_ERR(priv->rstc);
+		}
 	} else {
 		priv->reset = devm_gpiod_get_optional(dev, "reset",
 						      GPIOD_OUT_LOW);
Signature · 1 line
2.39.2
author maintainer
#24 lore raw

RFC PATCH v3 13/15 net: dsa: mt7530: add support for 10G link modes for CPU port

In reply to Daniel Golle

The built-in switch of the MT7988 SoC is internally connected using a stateless 10G link. Add support for 10G interface modes to silence a warning otherwise occurring when the switch driver is setup.

---
 drivers/net/dsa/mt7530.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
drivers/net/dsa/mt7530.c +6 -1
index fd55ddc2d1eb3..a4b49e5753bdc 100644
@@ -2616,6 +2616,9 @@ mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 	case PHY_INTERFACE_MODE_1000BASEX:
 	case PHY_INTERFACE_MODE_2500BASEX:
 		/* handled in SGMII PCS driver */
+	case PHY_INTERFACE_MODE_USXGMII:
+	case PHY_INTERFACE_MODE_10GKR:
+		/* internal stateless 10G link */
 		return 0;
 	default:
 		return -EINVAL;
@@ -2739,7 +2742,9 @@ static void mt753x_phylink_mac_link_up(struct dsa_switch *ds, int port,
 	 * variants.
 	 */
 	if (interface == PHY_INTERFACE_MODE_TRGMII ||
-	    (phy_interface_mode_is_8023z(interface))) {
+	    interface == PHY_INTERFACE_MODE_USXGMII ||
+	    interface == PHY_INTERFACE_MODE_10GKR ||
+	    phy_interface_mode_is_8023z(interface)) {
 		speed = SPEED_1000;
 		duplex = DUPLEX_FULL;
 	}
Signature · 1 line
2.39.2
author maintainer
#26 lore raw

RFC PATCH v3 14/15 net: dsa: mt7530: introduce driver for MT7988 built-in switch

In reply to Daniel Golle

Add driver for the built-in Gigabit Ethernet switch which can be found in the MediaTek MT7988 SoC.

The switch shares most of its design with MT7530 and MT7531, but has it's registers mapped into the SoCs register space rather than being connected externally or internally via MDIO.

Introduce a new platform driver to support that.

---
 MAINTAINERS                   |  2 +
 drivers/net/dsa/Kconfig       | 12 +++++
 drivers/net/dsa/Makefile      |  1 +
 drivers/net/dsa/mt7530-mmio.c | 96 +++++++++++++++++++++++++++++++++++
 drivers/net/dsa/mt7530.c      | 86 ++++++++++++++++++++++++++++++-
 drivers/net/dsa/mt7530.h      | 12 ++---
 6 files changed, 201 insertions(+), 8 deletions(-)
 create mode 100644 drivers/net/dsa/mt7530-mmio.c
MAINTAINERS +2 -0
index 7feb52d9ae0b9..f39c2520d5323 100644
@@ -13174,9 +13174,11 @@ MEDIATEK SWITCH DRIVER
 M:	Sean Wang <[email protected]>
 M:	Landen Chao <[email protected]>
 M:	DENG Qingfang <[email protected]>
+M:	Daniel Golle <[email protected]>
 L:	[email protected]
 S:	Maintained
 F:	drivers/net/dsa/mt7530-mdio.c
+F:	drivers/net/dsa/mt7530-mmio.c
 F:	drivers/net/dsa/mt7530.*
 F:	net/dsa/tag_mtk.c
 
drivers/net/dsa/Kconfig +12 -0
index c2551b13324c2..de4d86e37973f 100644
@@ -52,6 +52,18 @@ config NET_DSA_MT7530
 	  Multi-chip module MT7530 in MT7621AT, MT7621DAT, MT7621ST and
 	  MT7623AI SoCs is supported as well.
 
+config NET_DSA_MT7988
+	tristate "MediaTek MT7988 built-in Ethernet switch support"
+	select NET_DSA_MT7530_COMMON
+	depends on HAS_IOMEM
+	help
+	  This enables support for the built-in Ethernet switch found
+	  in the MediaTek MT7988 SoC.
+	  The switch is a similar design as MT7531, however, unlike
+	  other MT7530 and MT7531 the switch registers are directly
+	  mapped into the SoCs register space rather than being accessible
+	  via MDIO.
+
 config NET_DSA_MV88E6060
 	tristate "Marvell 88E6060 ethernet switch chip support"
 	select NET_DSA_TAG_TRAILER
drivers/net/dsa/Makefile +1 -0
index 71250d7dd41af..103a33e20de4b 100644
@@ -8,6 +8,7 @@ endif
 obj-$(CONFIG_NET_DSA_LANTIQ_GSWIP) += lantiq_gswip.o
 obj-$(CONFIG_NET_DSA_MT7530_COMMON) += mt7530.o
 obj-$(CONFIG_NET_DSA_MT7530)	+= mt7530-mdio.o
+obj-$(CONFIG_NET_DSA_MT7988)	+= mt7530-mmio.o
 obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
 obj-$(CONFIG_NET_DSA_RZN1_A5PSW) += rzn1_a5psw.o
 obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
drivers/net/dsa/mt7530-mmio.c new file +96 -0

96 lines not on this page · raw message

drivers/net/dsa/mt7530.c +84 -2

110 lines not on this page · raw message

drivers/net/dsa/mt7530.h +6 -6
index ce02aa592a7a8..01db5c9724fa8 100644
@@ -18,6 +18,7 @@ enum mt753x_id {
 	ID_MT7530 = 0,
 	ID_MT7621 = 1,
 	ID_MT7531 = 2,
+	ID_MT7988 = 3,
 };
 
 #define	NUM_TRGMII_CTRL			5
@@ -54,11 +55,11 @@ enum mt753x_id {
 #define  MT7531_MIRROR_PORT_SET(x)	(((x) & MIRROR_MASK) << 16)
 #define  MT7531_CPU_PMAP_MASK		GENMASK(7, 0)
 
-#define MT753X_MIRROR_REG(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_REG(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_CFC : MT7530_MFC)
-#define MT753X_MIRROR_EN(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_EN(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_MIRROR_EN : MIRROR_EN)
-#define MT753X_MIRROR_MASK(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_MASK(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_MIRROR_MASK : MIRROR_MASK)
 
 /* Registers for BPDU and PAE frame control*/
@@ -295,9 +296,8 @@ enum mt7530_vlan_port_acc_frm {
 					 MT7531_FORCE_DPX | \
 					 MT7531_FORCE_RX_FC | \
 					 MT7531_FORCE_TX_FC)
-#define  PMCR_FORCE_MODE_ID(id)		(((id) == ID_MT7531) ? \
-					 MT7531_FORCE_MODE : \
-					 PMCR_FORCE_MODE)
+#define  PMCR_FORCE_MODE_ID(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
+					 MT7531_FORCE_MODE : PMCR_FORCE_MODE)
 #define  PMCR_LINK_SETTINGS_MASK	(PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
 					 PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
 					 PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
Signature · 1 line
2.39.2
author maintainer
#29 lore raw

RFC PATCH v3 15/15 dt-bindings: net: dsa: mediatek,mt7530: add mediatek,mt7988-switch

In reply to Daniel Golle

Add documentation for the built-in switch which can be found in the MediaTek MT7988 SoC.

---
 .../bindings/net/dsa/mediatek,mt7530.yaml     | 26 +++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml +24 -2
index 5ae9cd8f99a24..15953f0e9d1a6 100644
@@ -11,16 +11,23 @@ maintainers:
   - Landen Chao <[email protected]>
   - DENG Qingfang <[email protected]>
   - Sean Wang <[email protected]>
+  - Daniel Golle <[email protected]>
 
 description: |
-  There are two versions of MT7530, standalone and in a multi-chip module.
+  There are three versions of MT7530, standalone, in a multi-chip module and
+  built-into a SoC.
 
   MT7530 is a part of the multi-chip module in MT7620AN, MT7620DA, MT7620DAN,
   MT7620NN, MT7621AT, MT7621DAT, MT7621ST and MT7623AI SoCs.
 
+  The MT7988 SoC comes a built-in switch similar to MT7531 as well as 4 Gigabit
+  Ethernet PHYs and the switch registers are directly mapped into SoC's memory
+  map rather than using MDIO. It comes with an internally connected 10G CPU port
+  and 4 user ports connected to the built-in Gigabit Ethernet PHYs.
+
   MT7530 in MT7620AN, MT7620DA, MT7620DAN and MT7620NN SoCs has got 10/100 PHYs
   and the switch registers are directly mapped into SoC's memory map rather than
-  using MDIO. The DSA driver currently doesn't support this.
+  using MDIO. The DSA driver currently doesn't support MT7620 variants.
 
   There is only the standalone version of MT7531.
 
@@ -81,6 +88,10 @@ properties:
           Multi-chip module MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs
         const: mediatek,mt7621
 
+      - description:
+          Built-in switch of the MT7988 SoC
+        const: mediatek,mt7988-switch
+
   reg:
     maxItems: 1
 
@@ -268,6 +279,17 @@ allOf:
       required:
         - mediatek,mcm
 
+  - if:
+      properties:
+        compatible:
+          const: mediatek,mt7988-switch
+    then:
+      $ref: "#/$defs/mt7530-dsa-port"
+      properties:
+        gpio-controller: false
+        mediatek,mcm: false
+        reset-names: false
+
 unevaluatedProperties: false
 
 examples:
Signature · 1 line
2.39.2
maintainer
#4 lore raw

Re: [RFC PATCH net-next v3 03/15] net: dsa: mt7530: use regmap to access switch register space

In reply to Daniel Golle

Thanks for splitting this patchset up. This is much easier to review.

drivers/net/dsa/mt7530.c mt7530_mii_read(struct mt7530_priv *priv, u32 reg) · line 256

Quoted 11 lines
drivers/net/dsa/mt7530.c +11 -0
+static u32
+mt7530_mii_read(struct mt7530_priv *priv, u32 reg)
+{
+	int ret;
+	u32 val;
+
+	ret = regmap_read(priv->regmap, reg, &val);
+	if (ret) {
+		dev_err(priv->dev,
+			"failed to read mt7530 register\n");
+		return ret;

This is a u32 function. ret should be negative on error, which is going to be turned positive in order to return a u32. So you probably want to make this an int function.

Andrew

maintainer Reviewed-by on v3 5/15
#9 lore raw

Re: [RFC PATCH net-next v3 05/15] net: dsa: mt7530: introduce mutex helpers

In reply to Daniel Golle
Quoted 6 lines · Daniel Golle

As the MDIO bus lock only needs to be involved if actually operating on an MDIO-connected switch we will need to skip locking for built-in switches which are accessed via MMIO.
Create helper functions which simplify that upcoming change.

Andrew

maintainer Reviewed-by on v3 6/15
#11 lore raw

Re: [RFC PATCH net-next v3 06/15] net: dsa: mt7530: move p5_intf_modes() function to mt7530.c

In reply to Daniel Golle
Quoted 6 lines · Daniel Golle

In preparation of splitting mt7530.c into a driver for MDIO-connected as well as MDIO-accessed built-in switches on one hand and MMIO-accessed built-in switches move the p5_inft_modes() function from mt7530.h to mt7530.c. The function is only needed there and will trigger a compiler warning about a defined but unused function otherwise when including mt7530.h in the to-be-introduced bus-specific drivers.

The other way to avoid the warning is to mark it inline. The compiler will not warn than. But this solution is also good.

Andrew

maintainer Reviewed-by on v3 8/15
#15 lore raw

Re: [RFC PATCH net-next v3 08/15] net: dsa: mt7530: introduce mt7530_remove_common helper function

In reply to Daniel Golle
Quoted 5 lines · Daniel Golle

Move commonly used parts from mt7530_remove into new mt7530_remove_common helper function which will be used by both, mt7530_remove and the to-be-introduced mt7988_remove.

Andrew

maintainer Reviewed-by on v3 10/15
#19 lore raw

Re: [RFC PATCH net-next v3 10/15] net: dsa: mt7530: introduce separate MDIO driver

In reply to Daniel Golle
Quoted 10 lines · Daniel Golle

Split MT7530 switch driver into a common part and a part specific for MDIO connected switches and multi-chip modules.
Move MDIO-specific functions to newly introduced mt7530-mdio.c while keeping the common parts in mt7530.c.
In order to maintain compatibility with existing kernel configurations keep CONFIG_NET_DSA_MT7530 as symbol to select the MDIO-specific driver while the newly introduced hidden symbol CONFIG_NET_DSA_MT7530_COMMON is selected by CONFIG_NET_DSA_MT7530.

Andrew

maintainer Reviewed-by on v3 11/15
#21 lore raw

Re: [RFC PATCH net-next v3 11/15] net: dsa: mt7530: skip locking if MDIO bus isn't present

In reply to Daniel Golle
Quoted 11 lines · Daniel Golle

As MT7530 and MT7531 internally use 32-bit wide registers, each access to any register of the switch requires several operations on the MDIO bus. Hence if there is congruent access, e.g. due to PCS or PHY polling, this can mess up and interfere with another ongoing register access sequence.

However, the MDIO bus mutex is only relevant for MDIO-connected switches. Prepare switches which have there registers directly mapped into the SoCs register space via MMIO which do not require such locking. There we can simply use regmap's default locking mechanism.

Quoted 4 lines

Hence guard mutex operations to only be performed in case of MDIO connected switches.

Andrew

maintainer
#23 lore raw

Re: [RFC PATCH net-next v3 12/15] net: dsa: mt7530: add support for single-chip reset line

In reply to Daniel Golle
Quoted 16 lines · Daniel Golle

Similar to multi-chip-module MT7530 also MT7988 uses an internal reset line instead of using an optional reset GPIO like it is the case for external MT7530 and MT7531 ICs.
Add support for internal but non-MCM reset line in preparation for adding support for MT7988.

---
 drivers/net/dsa/mt7530.c | 6 ++++++
 1 file changed, 6 insertions(+)
drivers/net/dsa/mt7530.c +0 -0
index c6fad2d156160..fd55ddc2d1eb3 100644

drivers/net/dsa/mt7530.c mt7530_probe_common(struct mt7530_priv *priv) · line 3069

Quoted 4 lines
drivers/net/dsa/mt7530.c +1 -0
@@ -3066,6 +3066,12 @@ mt7530_probe_common(struct mt7530_priv *priv)
 			dev_err(dev, "Couldn't get our reset line\n");
 			return PTR_ERR(priv->rstc);
 		}
+	} else if (!priv->bus) {

!priv->bus is being used as a proxy here for MT7988. Maybe it would be better to unconditionally use devm_reset_control_get_optional()? Or move the reset out of mt7530_probe_common() because it is not actually common?

Andrew

maintainer Reviewed-by on v3 13/15
#25 lore raw

Re: [RFC PATCH net-next v3 13/15] net: dsa: mt7530: add support for 10G link modes for CPU port

In reply to Daniel Golle
Quoted 5 lines · Daniel Golle

The built-in switch of the MT7988 SoC is internally connected using a stateless 10G link. Add support for 10G interface modes to silence a warning otherwise occurring when the switch driver is setup.

Andrew

maintainer
#27 lore raw

Re: [RFC PATCH net-next v3 14/15] net: dsa: mt7530: introduce driver for MT7988 built-in switch

In reply to Daniel Golle
Quoted 11 lines
drivers/net/dsa/mt7530.h +1 -0
@@ -18,6 +18,7 @@ enum mt753x_id {
 	ID_MT7530 = 0,
 	ID_MT7621 = 1,
 	ID_MT7531 = 2,
+	ID_MT7988 = 3,
 };
 
 #define	NUM_TRGMII_CTRL			5
@@ -54,11 +55,11 @@ enum mt753x_id {
 #define  MT7531_MIRROR_PORT_SET(x)	(((x) & MIRROR_MASK) << 16)
 #define  MT7531_CPU_PMAP_MASK		GENMASK(7, 0)

drivers/net/dsa/mt7530.h enum mt753x_id { · line 63

Quoted 10 lines
drivers/net/dsa/mt7530.h +3 -3
 
-#define MT753X_MIRROR_REG(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_REG(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_CFC : MT7530_MFC)
-#define MT753X_MIRROR_EN(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_EN(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_MIRROR_EN : MIRROR_EN)
-#define MT753X_MIRROR_MASK(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_MASK(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_MIRROR_MASK : MIRROR_MASK)

Are there more devices coming soon? I'm just wondering if these should change into static inline functions with a switch statement? The current code is not going to scale too much more.

Andrew

author maintainer
#5 lore raw

Re: [RFC PATCH net-next v3 03/15] net: dsa: mt7530: use regmap to access switch register space

In reply to Andrew Lunn
Quoted 17 lines · Andrew Lunn

Thanks for splitting this patchset up. This is much easier to review.

drivers/net/dsa/mt7530.c mt7530_mii_read(struct mt7530_priv *priv, u32 reg) · line 256

Quoted 11 lines
drivers/net/dsa/mt7530.c +11 -0
+static u32
+mt7530_mii_read(struct mt7530_priv *priv, u32 reg)
+{
+	int ret;
+	u32 val;
+
+	ret = regmap_read(priv->regmap, reg, &val);
+	if (ret) {
+		dev_err(priv->dev,
+			"failed to read mt7530 register\n");
+		return ret;

This is a u32 function. ret should be negative on error, which is going to be turned positive in order to return a u32. So you probably want to make this an int function.

This is a pre-existing flaw in the code. As we are accessing 32-bit registers there has just never been any meaningful error handling. I guess the correct solution would be to not use the return value only to indicate success or error, and use an additional u32* parameter for the read value.

However, I was hestitating to convert all the calls (they are many) to follow that improved paradigm.

Should I?

author maintainer
#28 lore raw

Re: [RFC PATCH net-next v3 14/15] net: dsa: mt7530: introduce driver for MT7988 built-in switch

In reply to Andrew Lunn
Quoted 12 lines · Andrew Lunn
Quoted 12 lines
drivers/net/dsa/mt7530.h +1 -0
@@ -18,6 +18,7 @@ enum mt753x_id {
 	ID_MT7530 = 0,
 	ID_MT7621 = 1,
 	ID_MT7531 = 2,
+	ID_MT7988 = 3,
 };
 
 #define	NUM_TRGMII_CTRL			5
@@ -54,11 +55,11 @@ enum mt753x_id {
 #define  MT7531_MIRROR_PORT_SET(x)	(((x) & MIRROR_MASK) << 16)
 #define  MT7531_CPU_PMAP_MASK		GENMASK(7, 0)
 
Quoted 13 lines

drivers/net/dsa/mt7530.h enum mt753x_id { · line 63

Quoted 9 lines
drivers/net/dsa/mt7530.h +3 -3
-#define MT753X_MIRROR_REG(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_REG(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_CFC : MT7530_MFC)
-#define MT753X_MIRROR_EN(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_EN(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_MIRROR_EN : MIRROR_EN)
-#define MT753X_MIRROR_MASK(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_MASK(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_MIRROR_MASK : MIRROR_MASK)

Are there more devices coming soon? I'm just wondering if these should change into static inline functions with a switch statement? The current code is not going to scale too much more.

Afaik no devices with different built-in switches are in the pipe at this time, so this should be fine for a while.

maintainer
#6 lore raw

Re: [RFC PATCH net-next v3 03/15] net: dsa: mt7530: use regmap to access switch register space

In reply to Daniel Golle
Quoted 19 lines · Daniel Golle
Quoted 17 lines · Andrew Lunn

Thanks for splitting this patchset up. This is much easier to review.

drivers/net/dsa/mt7530.c mt7530_mii_read(struct mt7530_priv *priv, u32 reg) · line 256

Quoted 11 lines
drivers/net/dsa/mt7530.c +11 -0
+static u32
+mt7530_mii_read(struct mt7530_priv *priv, u32 reg)
+{
+	int ret;
+	u32 val;
+
+	ret = regmap_read(priv->regmap, reg, &val);
+	if (ret) {
+		dev_err(priv->dev,
+			"failed to read mt7530 register\n");
+		return ret;

This is a u32 function. ret should be negative on error, which is going to be turned positive in order to return a u32. So you probably want to make this an int function.

Quoted 2 lines

This is a pre-existing flaw in the code. As we are accessing 32-bit registers there has just never been any meaningful error handling.

O.K. At least i would not return the negative error code. Return 0, or 0xdeadbeef or something. And consider adding a WARN_ON_ONCE() so it is very loud when it goes wrong.

Quoted 3 lines

I guess the correct solution would be to not use the return value only to indicate success or error, and use an additional u32* parameter for the read value.

Yes, that is what mv88e6xxx does.

Quoted 2 lines

However, I was hestitating to convert all the calls (they are many) to follow that improved paradigm.

Yes, leave that for another time.

Andrew