Skip to contentSkip to conversation

net: dsa: initial support for MaxLinear MxL862xx switches

PATCH Superseded Daniel Golle 2 participants 7 messages Jan 30

Subsystems (6)

v10 of 14 Superseded Latest is v14 →

lore
Share & tools
lore
author maintainer
#1 lore raw

PATCH v10 1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx

In reply to Daniel Golle

Add documentation and an example for MaxLinear MxL86282 and MxL86252 switches.

---
v10: add microcontroller port 0
v9: no changes
v8: no changes
v7: no changes
v6: no changes
v5: no changes
RFC v4:
* remove labels from example
* remove 'bindings for' from commit title
RFC v3: no changes
RFC v2: better description in dt-bindings doc

---
 .../bindings/net/dsa/maxlinear,mxl862xx.yaml  | 160 ++++++++++++++++++
 MAINTAINERS                                   |   6 +
 2 files changed, 166 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml
Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml new file +160 -0
new file mode 100644
index 000000000000..6a60e0881a49
@@ -0,0 +1,160 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/maxlinear,mxl862xx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MaxLinear MxL862xx Ethernet Switch Family
+
+maintainers:
+  - Daniel Golle <[email protected]>
+
+description:
+  The MaxLinear MxL862xx switch family are multi-port Ethernet switches with
+  integrated 2.5GE PHYs. The MxL86252 has five PHY ports and the MxL86282
+  has eight PHY ports. Both models come with two 10 Gigabit/s SerDes
+  interfaces to be used to connect external PHYs or SFP cages, or as CPU
+  port.
+
+allOf:
+  - $ref: dsa.yaml#/$defs/ethernet-ports
+
+properties:
+  compatible:
+    enum:
+      - maxlinear,mxl86252
+      - maxlinear,mxl86282
+
+  reg:
+    maxItems: 1
+    description: MDIO address of the switch
+
+  mdio:
+    $ref: /schemas/net/mdio.yaml#
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        switch@0 {
+            compatible = "maxlinear,mxl86282";
+            reg = <0>;
+
+            ethernet-ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                /* Microcontroller port */
+                port@0 {
+                    reg = <0>;
+                    status = "disabled";
+                };
+
+                port@1 {
+                    reg = <1>;
+                    phy-handle = <&phy0>;
+                    phy-mode = "internal";
+                };
+
+                port@2 {
+                    reg = <2>;
+                    phy-handle = <&phy1>;
+                    phy-mode = "internal";
+                };
+
+                port@3 {
+                    reg = <3>;
+                    phy-handle = <&phy2>;
+                    phy-mode = "internal";
+                };
+
+                port@4 {
+                    reg = <4>;
+                    phy-handle = <&phy3>;
+                    phy-mode = "internal";
+                };
+
+                port@5 {
+                    reg = <5>;
+                    phy-handle = <&phy4>;
+                    phy-mode = "internal";
+                };
+
+                port@6 {
+                    reg = <6>;
+                    phy-handle = <&phy5>;
+                    phy-mode = "internal";
+                };
+
+                port@7 {
+                    reg = <7>;
+                    phy-handle = <&phy6>;
+                    phy-mode = "internal";
+                };
+
+                port@8 {
+                    reg = <8>;
+                    phy-handle = <&phy7>;
+                    phy-mode = "internal";
+                };
+
+                port@9 {
+                    reg = <9>;
+                    label = "cpu";
+                    ethernet = <&gmac0>;
+                    phy-mode = "usxgmii";
+
+                    fixed-link {
+                        speed = <10000>;
+                        full-duplex;
+                    };
+                };
+            };
+
+            mdio {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                phy0: ethernet-phy@0 {
+                    reg = <0>;
+                };
+
+                phy1: ethernet-phy@1 {
+                    reg = <1>;
+                };
+
+                phy2: ethernet-phy@2 {
+                    reg = <2>;
+                };
+
+                phy3: ethernet-phy@3 {
+                    reg = <3>;
+                };
+
+                phy4: ethernet-phy@4 {
+                    reg = <4>;
+                };
+
+                phy5: ethernet-phy@5 {
+                    reg = <5>;
+                };
+
+                phy6: ethernet-phy@6 {
+                    reg = <6>;
+                };
+
+                phy7: ethernet-phy@7 {
+                    reg = <7>;
+                };
+            };
+        };
+    };
MAINTAINERS +6 -0
index c3df85fd5acd..8a0cc2609a88 100644
@@ -15619,6 +15619,12 @@ S:	Supported
 F:	drivers/net/phy/mxl-86110.c
 F:	drivers/net/phy/mxl-gpy.c
 
+MAXLINEAR MXL862XX SWITCH DRIVER
+M:	Daniel Golle <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml
+
 MCAN DEVICE DRIVER
 M:	Markus Schneider-Pargmann <[email protected]>
 L:	[email protected]
Signature · 1 line
2.52.0
author maintainer
#2 lore raw

PATCH v10 2/4 net: dsa: add tag format for MxL862xx switches

In reply to Daniel Golle

Add proprietary special tag format for the MaxLinear MXL862xx family of switches. While using the same Ethertype as MaxLinear's GSW1xx switches, the actual tag format differs significantly, hence we need a dedicated tag driver for that.

---
v10: count ports starting from 0
v9: no changes
v8: no changes
v7: no changes
v6:
* remove unnecessary check for skb != NULL
* merge consecutively printed warnings into single dev_warn_ratelimited

v5:
* remove unused macro definitions

RFC v4:
* describe fields and variables with comments
* sub-interface is only 5 bits
* harmonize Kconfig symbol name
* maintain alphabetic order in Kconfig
* fix typo s/beginnig/beginning/
* fix typo s/swtiches/switches/
* arrange local variables in reverse xmas tree order

RFC v3: no changes
RFC v2: make sure all tag fields are initialized

---
 MAINTAINERS            |   1 +
 include/net/dsa.h      |   2 +
 net/dsa/Kconfig        |   7 +++
 net/dsa/Makefile       |   1 +
 net/dsa/tag_mxl862xx.c | 110 +++++++++++++++++++++++++++++++++++++++++
 5 files changed, 121 insertions(+)
 create mode 100644 net/dsa/tag_mxl862xx.c
MAINTAINERS +1 -0
index 8a0cc2609a88..bd33de42604e 100644
@@ -15624,6 +15624,7 @@ M:	Daniel Golle <[email protected]>
 L:	[email protected]
 S:	Maintained
 F:	Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml
+F:	net/dsa/tag_mxl862xx.c
 
 MCAN DEVICE DRIVER
 M:	Markus Schneider-Pargmann <[email protected]>
include/net/dsa.h +2 -0
index 6b2b5ed64ea4..1e33242b6d94 100644
@@ -57,6 +57,7 @@ struct tc_action;
 #define DSA_TAG_PROTO_BRCM_LEGACY_FCS_VALUE	29
 #define DSA_TAG_PROTO_YT921X_VALUE		30
 #define DSA_TAG_PROTO_MXL_GSW1XX_VALUE		31
+#define DSA_TAG_PROTO_MXL862_VALUE		32
 
 enum dsa_tag_protocol {
 	DSA_TAG_PROTO_NONE		= DSA_TAG_PROTO_NONE_VALUE,
@@ -91,6 +92,7 @@ enum dsa_tag_protocol {
 	DSA_TAG_PROTO_VSC73XX_8021Q	= DSA_TAG_PROTO_VSC73XX_8021Q_VALUE,
 	DSA_TAG_PROTO_YT921X		= DSA_TAG_PROTO_YT921X_VALUE,
 	DSA_TAG_PROTO_MXL_GSW1XX	= DSA_TAG_PROTO_MXL_GSW1XX_VALUE,
+	DSA_TAG_PROTO_MXL862		= DSA_TAG_PROTO_MXL862_VALUE,
 };
 
 struct dsa_switch;
net/dsa/Kconfig +7 -0
index f86b30742122..efc95759a10e 100644
@@ -104,6 +104,13 @@ config NET_DSA_TAG_MTK
 	  Say Y or M if you want to enable support for tagging frames for
 	  Mediatek switches.
 
+config NET_DSA_TAG_MXL_862XX
+	tristate "Tag driver for MxL862xx switches"
+	help
+	  Say Y or M if you want to enable support for tagging frames for the
+	  Maxlinear MxL86252 and MxL86282 switches using their native 8-byte
+	  tagging protocol.
+
 config NET_DSA_TAG_MXL_GSW1XX
 	tristate "Tag driver for MaxLinear GSW1xx switches"
 	help
net/dsa/Makefile +1 -0
index 42d173f5a701..bf7247759a64 100644
@@ -28,6 +28,7 @@ obj-$(CONFIG_NET_DSA_TAG_HELLCREEK) += tag_hellcreek.o
 obj-$(CONFIG_NET_DSA_TAG_KSZ) += tag_ksz.o
 obj-$(CONFIG_NET_DSA_TAG_LAN9303) += tag_lan9303.o
 obj-$(CONFIG_NET_DSA_TAG_MTK) += tag_mtk.o
+obj-$(CONFIG_NET_DSA_TAG_MXL_862XX) += tag_mxl862xx.o
 obj-$(CONFIG_NET_DSA_TAG_MXL_GSW1XX) += tag_mxl-gsw1xx.o
 obj-$(CONFIG_NET_DSA_TAG_NONE) += tag_none.o
 obj-$(CONFIG_NET_DSA_TAG_OCELOT) += tag_ocelot.o
net/dsa/tag_mxl862xx.c new file +110 -0

110 lines not on this page · raw message

Signature · 1 line
2.52.0
author maintainer
#3 lore raw

PATCH v10 3/4 net: mdio: add unlocked mdiodev C45 bus accessors

In reply to Daniel Golle

Add helper inline functions __mdiodev_c45_read() and __mdiodev_c45_write(), which are the C45 equivalents of the existing __mdiodev_read() and __mdiodev_write() added by commit e6a45700e7e1 ("net: mdio: add unlocked mdiobus and mdiodev bus accessors")

---
v10: no changes
v9: no changes
v8: no changes
v7: no changes
v6: no changes
v5: fix indentation
RFC v4: no changes
RFC v3: no changes
RFC v2: add this patch, initial submission

---
 include/linux/mdio.h | 13 +++++++++++++
 1 file changed, 13 insertions(+)
include/linux/mdio.h +13 -0
index 42d6d47e445b..52d94b8ae371 100644
@@ -648,6 +648,19 @@ static inline int mdiodev_modify_changed(struct mdio_device *mdiodev,
 				      mask, set);
 }
 
+static inline int __mdiodev_c45_read(struct mdio_device *mdiodev, int devad,
+				     u16 regnum)
+{
+	return __mdiobus_c45_read(mdiodev->bus, mdiodev->addr, devad, regnum);
+}
+
+static inline int __mdiodev_c45_write(struct mdio_device *mdiodev, u32 devad,
+				      u16 regnum, u16 val)
+{
+	return __mdiobus_c45_write(mdiodev->bus, mdiodev->addr, devad, regnum,
+				   val);
+}
+
 static inline int mdiodev_c45_modify(struct mdio_device *mdiodev, int devad,
 				     u32 regnum, u16 mask, u16 set)
 {
Signature · 1 line
2.52.0
author maintainer
#4 lore raw

PATCH v10 4/4 net: dsa: add basic initial driver for MxL862xx switches

In reply to Daniel Golle

Add very basic DSA driver for MaxLinear's MxL862xx switches.

In contrast to previous MaxLinear switches the MxL862xx has a built-in processor that runs a sophisticated firmware based on Zephyr RTOS. Interaction between the host and the switch hence is organized using a software API of that firmware rather than accessing hardware registers directly.

Add descriptions of the most basic firmware API calls to access the built-in MDIO bus hosting the 2.5GE PHYs, basic port control as well as setting up the CPU port.

Implement a very basic DSA driver using that API which is sufficient to get packets flowing between the user ports and the CPU port.

The firmware offers all features one would expect from a modern switch hardware, they will be added one by one in follow-up patch series.

---
v10:
* fix indentation in kernel-doc
* remove misleading comment regarding sub-interface IDs
* remove unused macros, set MXL862XX_MAX_PORTS to 17
* count ports starting from 0, 0 being the microcontroller
* improve port setup:
- split tag protocol and CTP port assignment
- use ports cpu_dp instead of relying on single (ie. first) CPU port
- handle CPU port like any other port
- prepare forward DT compatibility with multiple CPU ports

v9:
* remove practically unused struct hw_info
* lots of kerneldoc improvements in mxl862xx-api.h
* drop .mac_select_pcs() stub
* better handling for firmware error return value
* apply reverse xmas tree in mxl862xx_api_wrap
* guard headers with #ifdef macro
* include net/dsa.h and linux/mdio.h in mxl862xx.h
* call mxl862xx_port_fast_age() only once in .port_setup
* don't create isolation bridges for unused ports
* replace errornous cast with correct range of values denoting firmware errors

v8:
* use le32 endian in bridge_port_config API
* remove duplciate assignment of br_port_cfg.bridge_port_id when setting up CPU port

v7:
* fix kerneldoc style

v6:
* include bridge and bridgeport API needed to isolate ports
* remove warning in .setup as ports are now isolated
* make ready-after-reset check more robust by adding delay
* sort structs in order of struct definitions
* best effort to sort functions without introducing additional prototypes
* always use enums with kerneldoc comments in mxl862xx-api.h
* remove bogus .phy_read and .phy_write DSA ops as the driver anyway registers a user MDIO bus with Clause-22 and Clause-45 operations
* various small style fixes

v5:
* output warning in .setup regarding unknown pre-configuration
* add comment explaining why CFGGET is used in reset function

RFC v4:
* poll switch readiness after reset
* implement driver shutdown
* added port_fast_aging API call and driver op
* unified port setup in new .port_setup op
* improve comment explaining special handlign for unaligned API read
* various typos

RFC v3:
* fix return value being uninitialized on error in mxl862xx_api_wrap()
* add missing descrition in kerneldoc comment of
struct mxl862xx_ss_sp_tag

RFC v2:
* make use of struct mdio_device
* add phylink_mac_ops stubs
* drop leftover nonsense from mxl862xx_phylink_get_caps()
* use __le32 instead of enum types in over-the-wire structs
* use existing MDIO_* macros whenever possible
* simplify API constants to be more readable
* use readx_poll_timeout instead of open-coding poll timeout loop
* add mxl862xx_reg_read() and mxl862xx_reg_write() helpers
* demystify error codes returned by the firmware
* add #defines for mxl862xx_ss_sp_tag member values
* move reset to dedicated function, clarify magic number being the reset command ID

---
 MAINTAINERS                              |   1 +
 drivers/net/dsa/Kconfig                  |   2 +
 drivers/net/dsa/Makefile                 |   1 +
 drivers/net/dsa/mxl862xx/Kconfig         |  12 +
 drivers/net/dsa/mxl862xx/Makefile        |   3 +
 drivers/net/dsa/mxl862xx/mxl862xx-api.h  | 671 +++++++++++++++++++++++
 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h  |  49 ++
 drivers/net/dsa/mxl862xx/mxl862xx-host.c | 245 +++++++++
 drivers/net/dsa/mxl862xx/mxl862xx-host.h |  12 +
 drivers/net/dsa/mxl862xx/mxl862xx.c      | 476 ++++++++++++++++
 drivers/net/dsa/mxl862xx/mxl862xx.h      |  16 +
 11 files changed, 1488 insertions(+)
 create mode 100644 drivers/net/dsa/mxl862xx/Kconfig
 create mode 100644 drivers/net/dsa/mxl862xx/Makefile
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-api.h
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.c
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.h
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.c
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.h
MAINTAINERS +1 -0
index bd33de42604e..ca941ca5ddf1 100644
@@ -15624,6 +15624,7 @@ M:	Daniel Golle <[email protected]>
 L:	[email protected]
 S:	Maintained
 F:	Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml
+F:	drivers/net/dsa/mxl862xx/
 F:	net/dsa/tag_mxl862xx.c
 
 MCAN DEVICE DRIVER
drivers/net/dsa/Kconfig +2 -0
index 7eb301fd987d..18f6e8b7f4cb 100644
@@ -74,6 +74,8 @@ source "drivers/net/dsa/microchip/Kconfig"
 
 source "drivers/net/dsa/mv88e6xxx/Kconfig"
 
+source "drivers/net/dsa/mxl862xx/Kconfig"
+
 source "drivers/net/dsa/ocelot/Kconfig"
 
 source "drivers/net/dsa/qca/Kconfig"
drivers/net/dsa/Makefile +1 -0
index 16de4ba3fa38..f5a463b87ec2 100644
@@ -20,6 +20,7 @@ obj-y				+= hirschmann/
 obj-y				+= lantiq/
 obj-y				+= microchip/
 obj-y				+= mv88e6xxx/
+obj-y				+= mxl862xx/
 obj-y				+= ocelot/
 obj-y				+= qca/
 obj-y				+= realtek/
drivers/net/dsa/mxl862xx/Kconfig new file +12 -0
new file mode 100644
index 000000000000..3722260da7d8
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config NET_DSA_MXL862
+	tristate "MaxLinear MxL862xx"
+	depends on NET_DSA
+	select MAXLINEAR_GPHY
+	select NET_DSA_TAG_MXL_862XX
+	help
+	  This enables support for the MaxLinear MxL862xx switch family.
+	  These switches have two 10GE SerDes interfaces, one typically
+	  used as CPU port.
+	   MxL86282 has eight 2.5 Gigabit PHYs
+	   MxL86252 has five 2.5 Gigabit PHYs
drivers/net/dsa/mxl862xx/Makefile new file +3 -0
new file mode 100644
index 000000000000..d23dd3cd511d
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_NET_DSA_MXL862) += mxl862xx_dsa.o
+mxl862xx_dsa-y := mxl862xx.o mxl862xx-host.o
drivers/net/dsa/mxl862xx/mxl862xx-api.h new file +671 -0

671 lines not on this page · raw message

drivers/net/dsa/mxl862xx/mxl862xx-cmd.h new file +49 -0

49 lines not on this page · raw message

drivers/net/dsa/mxl862xx/mxl862xx-host.c new file +245 -0

245 lines not on this page · raw message

drivers/net/dsa/mxl862xx/mxl862xx-host.h new file +12 -0
new file mode 100644
index 000000000000..7cc496f6be5c
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+
+#ifndef __MXL862XX_HOST_H
+#define __MXL862XX_HOST_H
+
+#include "mxl862xx.h"
+
+int mxl862xx_api_wrap(struct mxl862xx_priv *priv, u16 cmd, void *data, u16 size,
+		      bool read, bool quiet);
+int mxl862xx_reset(struct mxl862xx_priv *priv);
+
+#endif /* __MXL862XX_HOST_H */
drivers/net/dsa/mxl862xx/mxl862xx.c new file +476 -0

476 lines not on this page · raw message

drivers/net/dsa/mxl862xx/mxl862xx.h new file +16 -0
new file mode 100644
index 000000000000..bfeb436942d5
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+
+#ifndef __MXL862XX_H
+#define __MXL862XX_H
+
+#include <linux/mdio.h>
+#include <net/dsa.h>
+
+#define MXL862XX_MAX_PORTS		17
+
+struct mxl862xx_priv {
+	struct dsa_switch *ds;
+	struct mdio_device *mdiodev;
+};
+
+#endif /* __MXL862XX_H */
Signature · 1 line
2.52.0

Daniel Golle

author maintainer
#0 lore raw

v10 cover net: dsa: initial support for MaxLinear MxL862xx switches

This series adds very basic DSA support for the MaxLinear MxL86252 (5x 2500Base-T PHYs) and MxL86282 (8x 2500Base-T PHYs) switches. In addition to the 2.5G TP ports both switches also come with two SerDes interfaces which can be used either to connect external PHYs or SFP cages, or as CPU port when using the switch with this DSA driver.

MxL862xx integrates a firmware running on an embedded processor (running Zephyr RTOS). Host interaction uses a simple netlink-like API transported over MDIO/MMD.

This series includes only what's needed to pass traffic between user ports and the CPU port: relayed MDIO to internal PHYs, basic port enable/disable, and CPU-port special tagging.

The SerDes interface of the CPU port is automatically configured by the switch after reset using a board-specific configuration stored together with the firmware in the flash chip attached to the switch, so no action is needed from the driver to setup the interface mode of the CPU port.

Also MAC settings of the PHY ports are automatically configured, which means the driver works fine with phylink_mac_ops being all no-op stubs.

Multiple follow up series will bring support for setting up the other SerDes PCS interface (ie. not used for the CPU port), bridge, VLAN, ... offloading, and support for using an 802.1Q-based special tag instead of the proprietary 8-byte tag.
---
basic DSA selftests were run, results:
* no_forwarding.sh: all tests PASS
* bridge_vlan_unaware.sh: all tests PASS
* bridge_vlan_mcast.sh: all tests PASS
* bridge_vlan_aware.sh: all tests PASS
* local_termination.sh: all tests PASS or XFAIL, except for
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address [FAIL]
reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address, allmulti [FAIL]
reception succeeded, but should have failed

As obviously this is mostly testing the Linux software bridge at this point so I didn't bother to run any of the FDB or MDB related tests.

Some mystery about the relationship between the sub-interface ID and CTP port assignment remains for now, so I cannot yet fully explain the magic numbers when calculating the two.
(Why is it neccesary to allocate 23 CTPs when using port 9 as CPU port while there are at most 17 phyiscal interfaces in total, and only at most 13 when using one of the two SerDes as CPU interface? Why is there an offset of 16 when calculating the sub-interface ID? How will a total of 17 ports be possibly represented in a 4-bit field in the tag RX path?)

At this point this doesn't impact functionality, and I hope for further clarification discussing all that with MaxLinear engineers.

I believe the initial driver is anyway in good shape now, a follow-up series addressing configuring the SerDes interfaces will also have to take care of CTP assignment and sub-interfaces to not hit the mentioned 4-bit cap in the tag driver.

Changes since v9:
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* add microcontroller port 0
2/4 net: dsa: add tag format for MxL862xx switches
* count ports starting from 0
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix indentation in kernel-doc
* remove misleading comment regarding sub-interface IDs
* remove unused macros, set MXL862XX_MAX_PORTS to 17
* count ports starting from 0, 0 being the microcontroller
* improve port setup:
- split tag protocol and CTP port assignment
- use ports cpu_dp instead of relying on single (ie. first) CPU port
- handle CPU port like any other port
- prepare forward DT compatibility with multiple CPU ports

Changes since v8:
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* remove practically unused struct hw_info
* lots of kerneldoc improvements in mxl862xx-api.h
* drop .mac_select_pcs() stub
* better handling for firmware error return value
* apply reverse xmas tree in mxl862xx_api_wrap
* guard headers with #ifdef macro
* include net/dsa.h and linux/mdio.h in mxl862xx.h
* call mxl862xx_port_fast_age() only once in .port_setup
* don't create isolation bridges for unused ports
* replace errornous cast with correct range of values denoting firmware errors

Changes since v7
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* use little-endian in bridge_port_config API
* remove duplciate assignment of br_port_cfg.bridge_port_id when setting up CPU port

Changes since v6
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix kerneldoc style

Changes since RFC v5
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes

2/4 net: dsa: add tag format for MxL862xx switches
* remove unnecessary check for skb != NULL
* merge consecutively printed warnings into single dev_warn_ratelimited

3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes

4/4 net: dsa: add basic initial driver for MxL862xx switches
* include bridge and bridgeport API needed to isolate ports
* remove warning in .setup as ports are now isolated
* make ready-after-reset check more robust by adding delay
* sort structs in order of struct definitions
* best effort to sort functions without introducing additional prototypes
* always use enums with kerneldoc comments in mxl862xx-api.h
* remove bogus .phy_read and .phy_write DSA ops as the driver anyway registers a user MDIO bus with Clause-22 and Clause-45 operations
* various small style fixes

Changes since RFC v4
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes

2/4 net: dsa: add tag format for MxL862xx switches
* drop unused precompiler macros

3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* fix indentation

4/4 net: dsa: add basic initial driver for MxL862xx switches
* output warning in .setup regarding unknown pre-configuration
* add comment explaining why CFGGET is used in reset function

Changes since RFC v3
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* remove labels from example
* remove 'bindings for' from commit title

2/4 net: dsa: add tag format for MxL862xx switches
* describe fields and variables with comments
* sub-interface is only 5 bits
* harmonize Kconfig symbol name
* maintain alphabetic order in Kconfig
* fix typo s/beginnig/beginning/
* fix typo s/swtiches/switches/
* arrange local variables in reverse xmas tree order

3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* unchanged

4/4 net: dsa: add basic initial driver for MxL862xx switches
* poll switch readiness after reset
* implement driver shutdown
* added port_fast_aging API call and driver op
* unified port setup in new .port_setup op
* improve comment explaining special handlign for unaligned API read
* various typos and formatting improvements

Changes since RFC v2
1/4, 2/4, 3/4: unchanged

4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix return value being uninitialized on error in mxl862xx_api_wrap()
* add missing description in kerneldoc comment of
struct mxl862xx_ss_sp_tag

Changes since initial RFC

1/4 dt-bindings: net: dsa: add bindings for MaxLinear MxL862xx
* better description in dt-bindings doc

2/4 net: dsa: add tag formats for MxL862xx switches
* make sure all tag fields are initialized

3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* new patch

4/4 net: dsa: add basic initial driver for MxL862xx switches
* make use of struct mdio_device
* add phylink_mac_ops stubs
* drop leftover nonsense from mxl862xx_phylink_get_caps()
* fix endian conversions
* use __le32 instead of enum types in over-the-wire structs
* use existing MDIO_* macros whenever possible
* simplify API constants to be more readable
* use readx_poll_timeout instead of open-coding poll timeout loop
* add mxl862xx_reg_read() and mxl862xx_reg_write() helpers
* demystify error codes returned by the firmware
* add #defines for mxl862xx_ss_sp_tag member values
* move reset to dedicated function, clarify magic number being the reset command ID

Daniel Golle (4):
dt-bindings: net: dsa: add MaxLinear MxL862xx
net: dsa: add tag format for MxL862xx switches
net: mdio: add unlocked mdiodev C45 bus accessors
net: dsa: add basic initial driver for MxL862xx switches

 .../bindings/net/dsa/maxlinear,mxl862xx.yaml  | 160 +++++
 MAINTAINERS                                   |   8 +
 drivers/net/dsa/Kconfig                       |   2 +
 drivers/net/dsa/Makefile                      |   1 +
 drivers/net/dsa/mxl862xx/Kconfig              |  12 +
 drivers/net/dsa/mxl862xx/Makefile             |   3 +
 drivers/net/dsa/mxl862xx/mxl862xx-api.h       | 671 ++++++++++++++++++
 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h       |  49 ++
 drivers/net/dsa/mxl862xx/mxl862xx-host.c      | 245 +++++++
 drivers/net/dsa/mxl862xx/mxl862xx-host.h      |  12 +
 drivers/net/dsa/mxl862xx/mxl862xx.c           | 476 +++++++++++++
 drivers/net/dsa/mxl862xx/mxl862xx.h           |  16 +
 include/linux/mdio.h                          |  13 +
 include/net/dsa.h                             |   2 +
 net/dsa/Kconfig                               |   7 +
 net/dsa/Makefile                              |   1 +
 net/dsa/tag_mxl862xx.c                        | 110 +++
 17 files changed, 1788 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml
 create mode 100644 drivers/net/dsa/mxl862xx/Kconfig
 create mode 100644 drivers/net/dsa/mxl862xx/Makefile
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-api.h
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.c
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.h
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.c
 create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.h
 create mode 100644 net/dsa/tag_mxl862xx.c
Signature · 1 line
2.52.0
#5 lore raw

Re: [PATCH net-next v10 4/4] net: dsa: add basic initial driver for MxL862xx switches

In reply to Daniel Golle
kernel test robot noticed the following build errors:

Hi Daniel,

kernel test robot noticed the following build errors:

[auto build test ERROR on net-next/main]

url:    https://github.com/intel-lab-lkp/linux/commits/Daniel-Golle/dt-bindings-net-dsa-add-MaxLinear-MxL862xx/20260130-085313
base:   net-next/main
patch link:    https://lore.kernel.org/r/281fd7e777b51849fac9ef5191679586cc2a1b54.1769731630.git.daniel%40makrotopia.org
patch subject: [PATCH net-next v10 4/4] net: dsa: add basic initial driver for MxL862xx switches
config: nios2-allmodconfig (https://download.01.org/0day-ci/archive/20260130/[email protected]/config)
compiler: nios2-linux-gcc (GCC) 11.5.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20260130/[email protected]/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/

All errors (new ones prefixed by >>):

drivers/net/dsa/mxl862xx/mxl862xx.c: In function 'mxl862xx_port_setup':
drivers/net/dsa/mxl862xx/mxl862xx.c:331:32: error: passing argument 1 of 'dsa_port_is_unused' from incompatible pointer type [-Werror=incompatible-pointer-types]

     331 |         if (dsa_port_is_unused(ds, port) ||
         |                                ^~
         |                                |
         |                                struct dsa_switch *
   In file included from drivers/net/dsa/mxl862xx/mxl862xx.c:16:
   include/net/dsa.h:546:56: note: expected 'struct dsa_port *' but argument is of type 'struct dsa_switch *'
     546 | static inline bool dsa_port_is_unused(struct dsa_port *dp)
         |                                       ~~~~~~~~~~~~~~~~~^~
>> drivers/net/dsa/mxl862xx/mxl862xx.c:331:13: error: too many arguments to function 'dsa_port_is_unused'
     331 |         if (dsa_port_is_unused(ds, port) ||
         |             ^~~~~~~~~~~~~~~~~~
   In file included from drivers/net/dsa/mxl862xx/mxl862xx.c:16:
   include/net/dsa.h:546:20: note: declared here
     546 | static inline bool dsa_port_is_unused(struct dsa_port *dp)
         |                    ^~~~~~~~~~~~~~~~~~
   drivers/net/dsa/mxl862xx/mxl862xx.c:332:29: error: passing argument 1 of 'dsa_port_is_dsa' from incompatible pointer type [-Werror=incompatible-pointer-types]
     332 |             dsa_port_is_dsa(ds, port))
         |                             ^~
         |                             |
         |                             struct dsa_switch *
   In file included from drivers/net/dsa/mxl862xx/mxl862xx.c:16:
   include/net/dsa.h:531:53: note: expected 'struct dsa_port *' but argument is of type 'struct dsa_switch *'
     531 | static inline bool dsa_port_is_dsa(struct dsa_port *port)
         |                                    ~~~~~~~~~~~~~~~~~^~~~
>> drivers/net/dsa/mxl862xx/mxl862xx.c:332:13: error: too many arguments to function 'dsa_port_is_dsa'
     332 |             dsa_port_is_dsa(ds, port))
         |             ^~~~~~~~~~~~~~~

In file included from drivers/net/dsa/mxl862xx/mxl862xx.c:16:
include/net/dsa.h:531:20: note: declared here
531 | static inline bool dsa_port_is_dsa(struct dsa_port *port)
| ^~~~~~~~~~~~~~~
cc1: some warnings being treated as errors

vim +/dsa_port_is_unused +331 drivers/net/dsa/mxl862xx/mxl862xx.c

317
318 static int mxl862xx_port_setup(struct dsa_switch *ds, int port)
319 {
320 bool is_cpu_port = dsa_is_cpu_port(ds, port);
321 int ret;
322
323 /* disable port and flush MAC entries */
324 ret = mxl862xx_port_state(ds, port, false);
325 if (ret)
326 return ret;
327
328 mxl862xx_port_fast_age(ds, port);
329
330 /* skip setup for unused and DSA ports */

 > 331		if (dsa_port_is_unused(ds, port) ||
 > 332		    dsa_port_is_dsa(ds, port))

333 return 0;
334
335 /* configure tag protocol */
336 ret = mxl862xx_configure_sp_tag_proto(ds, port, is_cpu_port);
337 if (ret)
338 return ret;
339
340 /* assign CTP port IDs */
341 ret = mxl862xx_configure_ctp_port(ds, port, port,
342 is_cpu_port ? 32 - port : 1);
343 if (ret)
344 return ret;
345
346 if (is_cpu_port)
347 /* assign user ports to CPU port bridge */
348 return mxl862xx_setup_cpu_bridge(ds, port);
349
350 /* setup single-port bridge for user ports */
351 return mxl862xx_add_single_port_bridge(ds, port);
352 }
353

Signature · 2 lines
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki
#6 lore raw

Re: [PATCH net-next v10 4/4] net: dsa: add basic initial driver for MxL862xx switches

In reply to Daniel Golle
kernel test robot noticed the following build errors:

Hi Daniel,

kernel test robot noticed the following build errors:

[auto build test ERROR on net-next/main]

url:    https://github.com/intel-lab-lkp/linux/commits/Daniel-Golle/dt-bindings-net-dsa-add-MaxLinear-MxL862xx/20260130-085313
base:   net-next/main
patch link:    https://lore.kernel.org/r/281fd7e777b51849fac9ef5191679586cc2a1b54.1769731630.git.daniel%40makrotopia.org
patch subject: [PATCH net-next v10 4/4] net: dsa: add basic initial driver for MxL862xx switches
config: sh-allmodconfig (https://download.01.org/0day-ci/archive/20260130/[email protected]/config)
compiler: sh4-linux-gcc (GCC) 15.2.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20260130/[email protected]/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/

All errors (new ones prefixed by >>):

drivers/net/dsa/mxl862xx/mxl862xx.c: In function 'mxl862xx_port_setup':

>> drivers/net/dsa/mxl862xx/mxl862xx.c:331:32: error: passing argument 1 of 'dsa_port_is_unused' from incompatible pointer type [-Wincompatible-pointer-types]
     331 |         if (dsa_port_is_unused(ds, port) ||
         |                                ^~
         |                                |
         |                                struct dsa_switch *
   In file included from drivers/net/dsa/mxl862xx/mxl862xx.c:16:
   include/net/dsa.h:546:56: note: expected 'struct dsa_port *' but argument is of type 'struct dsa_switch *'
     546 | static inline bool dsa_port_is_unused(struct dsa_port *dp)
         |                                       ~~~~~~~~~~~~~~~~~^~
>> drivers/net/dsa/mxl862xx/mxl862xx.c:331:13: error: too many arguments to function 'dsa_port_is_unused'; expected 1, have 2
     331 |         if (dsa_port_is_unused(ds, port) ||
         |             ^~~~~~~~~~~~~~~~~~     ~~~~
   include/net/dsa.h:546:20: note: declared here
     546 | static inline bool dsa_port_is_unused(struct dsa_port *dp)
         |                    ^~~~~~~~~~~~~~~~~~
>> drivers/net/dsa/mxl862xx/mxl862xx.c:332:29: error: passing argument 1 of 'dsa_port_is_dsa' from incompatible pointer type [-Wincompatible-pointer-types]
     332 |             dsa_port_is_dsa(ds, port))
         |                             ^~
         |                             |
         |                             struct dsa_switch *
   include/net/dsa.h:531:53: note: expected 'struct dsa_port *' but argument is of type 'struct dsa_switch *'
     531 | static inline bool dsa_port_is_dsa(struct dsa_port *port)
         |                                    ~~~~~~~~~~~~~~~~~^~~~
>> drivers/net/dsa/mxl862xx/mxl862xx.c:332:13: error: too many arguments to function 'dsa_port_is_dsa'; expected 1, have 2
     332 |             dsa_port_is_dsa(ds, port))
         |             ^~~~~~~~~~~~~~~     ~~~~

include/net/dsa.h:531:20: note: declared here
531 | static inline bool dsa_port_is_dsa(struct dsa_port *port)
| ^~~~~~~~~~~~~~~

vim +/dsa_port_is_unused +331 drivers/net/dsa/mxl862xx/mxl862xx.c

317
318 static int mxl862xx_port_setup(struct dsa_switch *ds, int port)
319 {
320 bool is_cpu_port = dsa_is_cpu_port(ds, port);
321 int ret;
322
323 /* disable port and flush MAC entries */
324 ret = mxl862xx_port_state(ds, port, false);
325 if (ret)
326 return ret;
327
328 mxl862xx_port_fast_age(ds, port);
329
330 /* skip setup for unused and DSA ports */

 > 331		if (dsa_port_is_unused(ds, port) ||
 > 332		    dsa_port_is_dsa(ds, port))

333 return 0;
334
335 /* configure tag protocol */
336 ret = mxl862xx_configure_sp_tag_proto(ds, port, is_cpu_port);
337 if (ret)
338 return ret;
339
340 /* assign CTP port IDs */
341 ret = mxl862xx_configure_ctp_port(ds, port, port,
342 is_cpu_port ? 32 - port : 1);
343 if (ret)
344 return ret;
345
346 if (is_cpu_port)
347 /* assign user ports to CPU port bridge */
348 return mxl862xx_setup_cpu_bridge(ds, port);
349
350 /* setup single-port bridge for user ports */
351 return mxl862xx_add_single_port_bridge(ds, port);
352 }
353

Signature · 2 lines
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki