net: dsa: mxl-gsw1xx: setup polarities and validate chip
Subsystems (5)
v3 cover net: dsa: mxl-gsw1xx: setup polarities and validate chip
Now that common PHY properties make it easy to configure the SerDes RX and TX polarities, use that for the SGMII/1000Base-X/2500Base-X port of the MaxLinear GSW1xx switches.
Also, validate hardware in probe() function to make sure the switch is actually present and MDIO communication works properly.
---
Changes since v2:
* be more clear about describing polarity at port, ie. external pin level
Changes since initial submission:
* use allOf to include phy-common-props in dt-schema
* use phy_get_manual_rx_polarity and phy_get_manual_tx_polarity helpers instead of open-coding them
Daniel Golle (3):
dt-bindings: net: dsa: lantiq,gswip: reference common PHY properties
net: dsa: mxl-gsw1xx: configure SerDes port polarities
net: dsa: mxl-gsw1xx: validate chip ID
.../bindings/net/dsa/lantiq,gswip.yaml | 4 ++ drivers/net/dsa/lantiq/Kconfig | 1 + drivers/net/dsa/lantiq/mxl-gsw1xx.c | 66 +++++++++++++++---- drivers/net/dsa/lantiq/mxl-gsw1xx.h | 9 +++ 4 files changed, 68 insertions(+), 12 deletions(-)
Signature · 1 line
2.52.0
PATCH v3 1/3 dt-bindings: net: dsa: lantiq,gswip: reference common PHY properties
Reference the common PHY properties so RX and TX SerDes lane polarity of the SGMII/1000Base-X/2500Base-X port can be configured.
---
v3: commit message: clarify that the intention is to configure polarity
at port level, as opposed to the internal polarity of the PCS component
v2: use allOf to include PHY common properties, add example use
--- Documentation/devicetree/bindings/net/dsa/lantiq,gswip.yaml | 4 ++++ 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/net/dsa/lantiq,gswip.yaml +4 -0
@@ -105,6 +105,8 @@ patternProperties: patternProperties: "^(ethernet-)?port@[0-6]$": $ref: dsa-port.yaml# + allOf: + - $ref: /schemas/phy/phy-common-props.yaml# unevaluatedProperties: false properties:
@@ -288,6 +290,7 @@ examples: - | #include <dt-bindings/leds/common.h> + #include <dt-bindings/phy/phy.h> mdio { #address-cells = <1>;
@@ -320,6 +323,7 @@ examples: label = "wan"; phy-mode = "1000base-x"; managed = "in-band-status"; + tx-polarity = <PHY_POL_INVERT>; }; port@5 {
Signature · 1 line
2.52.0
PATCH v3 2/3 net: dsa: mxl-gsw1xx: configure SerDes port polarities
In reply to Daniel GolleConfigure SerDes (port 4) RX and TX polarities using the newly introduced generic properties. The polarities are described at the port level which equals the polarities of the external pins of the chip.
Note that the RX lane is inverted internally and the vendor driver simply always sets bit GSW1XX_SGMII_PHY_RX0_CFG2_INVERT unconditionally to end up with the correct (ie. as documented in datasheets) polarity at the external pins.
In this sense, PHY_POLARITY_NORMAL denotes normal polarity for pins as documented for the MRQFN 105-pin package (GSW120, GSW125, GSW140, GSW141 and GSW145 all use the same package and have identical pin layouts except for TP port 2 and 3 being N/C on GSW12x):
pin B18 (TX0_P) positive signal of the differential SGMII data output pair pin B19 (TX0_M) negative signal of the differential SGMII data output pair pin B20 (RX0_P) positive signal of the differential SGMII data input pair pin B21 (RX0_M) negative signal of the differential SGMII data input pair
---
v3: be clear about describing polarity at external pins
v2: use phy_get_manual_rx_polarity and phy_get_manual_tx_polarity
--- drivers/net/dsa/lantiq/Kconfig | 1 + drivers/net/dsa/lantiq/mxl-gsw1xx.c | 39 +++++++++++++++++++++-------- 2 files changed, 29 insertions(+), 11 deletions(-)
drivers/net/dsa/lantiq/Kconfig +1 -0
@@ -15,6 +15,7 @@ config NET_DSA_MXL_GSW1XX tristate "MaxLinear GSW1xx Ethernet switch support" select NET_DSA_TAG_MXL_GSW1XX select NET_DSA_LANTIQ_COMMON + select PHY_COMMON_PROPS help This enables support for the Intel/MaxLinear GSW1xx family of 1GE switches.
drivers/net/dsa/lantiq/mxl-gsw1xx.c +28 -11
@@ -15,6 +15,8 @@#include <linux/module.h> #include <linux/of_device.h> #include <linux/of_mdio.h> +#include <linux/phy/phy-common-props.h> +#include <linux/property.h> #include <linux/regmap.h> #include <linux/workqueue.h> #include <net/dsa.h>
@@ -229,11 +231,17 @@ static int gsw1xx_pcs_phy_xaui_write(struct gsw1xx_priv *priv, u16 addr, 1000, 100000); } -static int gsw1xx_pcs_reset (struct gsw1xx_priv *priv) +static int gsw1xx_pcs_reset (struct gsw1xx_priv *priv,phy_interface_t interface) { +struct dsa_port *sgmii_port; +unsigned int pol;int ret;u16 val; + sgmii_port =dsa_to_port (priv->gswip.ds,GSW1XX_SGMII_PORT ); +if (!sgmii_port) +return -EINVAL ; +/* Assert and deassert SGMII shell reset */ ret =regmap_set_bits (priv->shell,GSW1XX_SHELL_RST_REQ ,GSW1XX_RST_REQ_SGMII_SHELL );
@@ -260,15 +268,20 @@ static int gsw1xx_pcs_reset(struct gsw1xx_priv *priv)FIELD_PREP (GSW1XX_SGMII_PHY_RX0_CFG2_FILT_CNT ,GSW1XX_SGMII_PHY_RX0_CFG2_FILT_CNT_DEF ); + ret =phy_get_manual_rx_polarity (of_fwnode_handle (sgmii_port->dn), +phy_modes (interface), &pol); +if (ret) +return ret; +/* RX lane seems to be inverted internally, so bit * GSW1XX_SGMII_PHY_RX0_CFG2_INVERT needs to be set for normal -* (ie. non-inverted) operation. -* -* TODO: Take care of inverted RX pair once generic property is -* available +* (ie. non-inverted) operation matching the chips external pins as +* described in datasheets dated 2023-11-08, ie. pin B20 (RX0_P) being +* the positive signal and pin B21 (RX0_M) being the negative signal of +* the differential input pair. */ - - val |=GSW1XX_SGMII_PHY_RX0_CFG2_INVERT ; +if (pol ==PHY_POL_NORMAL ) + val |=GSW1XX_SGMII_PHY_RX0_CFG2_INVERT ; ret =regmap_write (priv->sgmii,GSW1XX_SGMII_PHY_RX0_CFG2 , val);if (ret <0 )
@@ -277,9 +290,13 @@ static int gsw1xx_pcs_reset(struct gsw1xx_priv *priv) val =FIELD_PREP (GSW1XX_SGMII_PHY_TX0_CFG3_VBOOST_LEVEL ,GSW1XX_SGMII_PHY_TX0_CFG3_VBOOST_LEVEL_DEF ); -/* TODO: Take care of inverted TX pair once generic property is -* available -*/ + ret =phy_get_manual_tx_polarity (of_fwnode_handle (sgmii_port->dn), +phy_modes (interface), &pol); +if (ret) +return ret; + +if (pol ==PHY_POL_INVERT ) + val |=GSW1XX_SGMII_PHY_TX0_CFG3_INVERT ; ret =regmap_write (priv->sgmii,GSW1XX_SGMII_PHY_TX0_CFG3 , val);if (ret <0 )
@@ -336,7 +353,7 @@ static int gsw1xx_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode, priv->tbi_interface =PHY_INTERFACE_MODE_NA ;if (!reconf) - ret =gsw1xx_pcs_reset (priv); + ret =gsw1xx_pcs_reset (priv, interface);if (ret)return ret;
Signature · 1 line
2.52.0
PATCH v3 3/3 net: dsa: mxl-gsw1xx: validate chip ID
In reply to Daniel GolleNo check for actually present hardware is being performed in the probe function of the mxl-gsw1xx switch driver. So even if the switch isn't present at the configured MDIO bus address the driver wrongly tells the user that a "GSWIP version 0 mod 0" was found, outputting errors about PHY capabilities not matching.
Read and validate the chip MANU_ID and PNUM_ID registers and output information while probing, but return an error and abort probing in case the hardware is not actually present.
---
v3: no changes
v2: no changes
drivers/net/dsa/lantiq/mxl-gsw1xx.c | 27 ++++++++++++++++++++++++++- drivers/net/dsa/lantiq/mxl-gsw1xx.h | 9 +++++++++ 2 files changed, 35 insertions(+), 1 deletion(-)
drivers/net/dsa/lantiq/mxl-gsw1xx.c +26 -1
@@ -688,7 +688,9 @@ static int gsw1xx_probe(struct mdio_device *mdiodev) {struct device *dev = &mdiodev->dev;struct gsw1xx_priv *priv; -u32 version; +u32 version, val; +u8 shellver; +u16 pnum;int ret; priv =devm_kzalloc (dev,sizeof (*priv),GFP_KERNEL );
@@ -736,6 +738,27 @@ static int gsw1xx_probe(struct mdio_device *mdiodev)if (IS_ERR (priv->shell))return PTR_ERR (priv->shell); + ret =regmap_read (priv->shell,GSW1XX_SHELL_MANU_ID , &val); +if (ret <0 ) +return ret; + +/* validate chip ID */ +if (FIELD_GET (GSW1XX_SHELL_MANU_ID_FIX1 , val) !=1 ) +return -ENODEV ; + +if (FIELD_GET (GSW1XX_SHELL_MANU_ID_MANID , val) != +GSW1XX_SHELL_MANU_ID_MANID_VAL ) +return -ENODEV ; + + pnum =FIELD_GET (GSW1XX_SHELL_MANU_ID_PNUML , val); + + ret =regmap_read (priv->shell,GSW1XX_SHELL_PNUM_ID , &val); +if (ret <0 ) +return ret; + + pnum |=FIELD_GET (GSW1XX_SHELL_PNUM_ID_PNUMM , val) <<4 ; + shellver =FIELD_GET (GSW1XX_SHELL_PNUM_ID_VER , val); + ret =gsw1xx_serdes_pcs_init (priv);if (ret <0 )return ret;
@@ -756,6 +779,8 @@ static int gsw1xx_probe(struct mdio_device *mdiodev)if (ret)return ret; +dev_info (dev,"standalone switch part number 0x%x v1.%u\n" , pnum, shellver); +dev_set_drvdata (dev, &priv->gswip);return 0 ;
drivers/net/dsa/lantiq/mxl-gsw1xx.h +9 -0
@@ -110,6 +110,15 @@#define GSW1XX_SHELL_BASE 0xfa00#define GSW1XX_SHELL_RST_REQ 0x01#define GSW1XX_RST_REQ_SGMII_SHELL BIT(5) +#define GSW1XX_SHELL_MANU_ID 0x10 +#define GSW1XX_SHELL_MANU_ID_PNUML GENMASK(15, 12) +#define GSW1XX_SHELL_MANU_ID_MANID GENMASK(11, 1) +#define GSW1XX_SHELL_MANU_ID_MANID_VAL 0x389 +#define GSW1XX_SHELL_MANU_ID_FIX1 BIT(0) +#define GSW1XX_SHELL_PNUM_ID 0x11 +#define GSW1XX_SHELL_PNUM_ID_VER GENMASK(15, 12) +#define GSW1XX_SHELL_PNUM_ID_PNUMM GENMASK(11, 0) +/* RGMII PAD Slew Control Register */ #define GSW1XX_SHELL_RGMII_SLEW_CFG 0x78#define RGMII_SLEW_CFG_DRV_TXC BIT(2)
Signature · 1 line
2.52.0
Quoted 10 lines · Daniel Golle
Now that common PHY properties make it easy to configure the SerDes RX and TX polarities, use that for the SGMII/1000Base-X/2500Base-X port of the MaxLinear GSW1xx switches.
Also, validate hardware in
probe()function to make sure the switch is actually present and MDIO communication works properly.
---
Changes since v2:
* be more clear about describing polarity at port, ie. external pin level
Quoted 4 lines
Changes since initial submission:
* use allOf to include phy-common-props in dt-schema
* usephy_get_manual_rx_polarityandphy_get_manual_tx_polarityhelpers instead of open-coding them
For the set:
Re: [PATCH net-next v3 1/3] dt-bindings: net: dsa: lantiq,gswip: reference common PHY properties
In reply to Daniel GolleQuoted 17 lines · Daniel Golle
Reference the common PHY properties so RX and TX SerDes lane polarity of the SGMII/1000Base-X/2500Base-X port can be configured.
Signed-off-by Daniel Golle <[email protected]>---
v3: commit message: clarify that the intention is to configure polarity
at port level, as opposed to the internal polarity of the PCS component
v2: use allOf to include PHY common properties, add example use--- Documentation/devicetree/bindings/net/dsa/lantiq,gswip.yaml | 4 ++++ 1 file changed, 4 insertions(+)Documentation/devicetree/bindings/net/dsa/lantiq,gswip.yaml +0
-0
Documentation/devicetree/bindings/net/dsa/lantiq,gswip.yaml patternProperties: · line 109
Quoted 5 lines
Documentation/devicetree/bindings/net/dsa/lantiq,gswip.yaml +2
-0@@ -105,6 +105,8 @@ patternProperties: patternProperties: "^(ethernet-)?port@[0-6]$": $ref: dsa-port.yaml# + allOf: + - $ref: /schemas/phy/phy-common-props.yaml#
If you respin, put both $ref's under the allOf.
Quoted 21 lines
Documentation/devicetree/bindings/net/dsa/lantiq,gswip.yaml +2
-0unevaluatedProperties: false properties:@@ -288,6 +290,7 @@ examples: - | #include <dt-bindings/leds/common.h> + #include <dt-bindings/phy/phy.h> mdio { #address-cells = <1>;@@ -320,6 +323,7 @@ examples: label = "wan"; phy-mode = "1000base-x"; managed = "in-band-status"; + tx-polarity = <PHY_POL_INVERT>; }; port@5 {Signature · 1 line
2.52.0
This series was applied to netdev/net-next.git (main) by Paolo Abeni <[email protected]>:
Hello:
This series was applied to netdev/net-next.git (main) by Paolo Abeni <[email protected]>:
Quoted 8 lines · On Sun, 1 Feb 2026 03:41:34 +0000 you wrote:
Now that common PHY properties make it easy to configure the SerDes RX and TX polarities, use that for the SGMII/1000Base-X/2500Base-X port of the MaxLinear GSW1xx switches.
Also, validate hardware in
probe()function to make sure the switch is actually present and MDIO communication works properly.[...]
Here is the summary with links:
- [net-next,v3,1/3] dt-bindings: net: dsa: lantiq,gswip: reference common PHY properties
https://git.kernel.org/netdev/net-next/c/431b777762d7 - [net-next,v3,2/3] net: dsa: mxl-gsw1xx: configure SerDes port polarities https://git.kernel.org/netdev/net-next/c/ffd034ac0912 - [net-next,v3,3/3] net: dsa: mxl-gsw1xx: validate chip ID https://git.kernel.org/netdev/net-next/c/a046d6fc54d4
You are awesome, thank you!
Signature · 2 lines
Deet-doot-dot, I am a bot. https://korg.docs.kernel.org/patchwork/pwbot.html