Skip to contentSkip to conversation

quake3 issues

LARTC Bjoern Metzdorf 2 participants 3 messages Jul 4, 2002

lore
Share & tools
lore
#0 lore raw

Hi,

I am using wshaper.htb from wondershaper 1.1a on 2.4.18 with htb2.

I have an adsl (german telekom) 128/768 line. I want to be able to play quake3 all the time without lag, even when there are heavy uploads going on.

I decided to use the fwmark method, then my line is not influenced at all by other minimize-delay TOS programs.

So I put marked all quake packets (-p udp --dport 20000:35000 -J MARK --set-mark 1).

Here you go:
-----------------------------------------------------------
DOWNLINK#00
UPLINK#00
DEV=eth0

# install root HTB, point default traffic to 1:20:
tc qdisc add dev $DEV root handle 1: htb default 20
# shape everything at $UPLINK speed - this prevents huge queues in your
# DSL modem which destroy latency:
tc class add dev $DEV parent 1: classid 1:1 htb rate ${UPLINK}kbit \
   burst 6k
# high prio class 1:10:
tc class add dev $DEV parent 1:1 classid 1:10 htb rate ${UPLINK}kbit \
   burst 6k prio 1
# bulk & default class 1:20 - gets slightly less traffic,
# and a lower priority:
tc class add dev $DEV parent 1:1 classid 1:20 htb \
   rate $[9*$UPLINK/10]kbit burst 6k prio 2
# all get Stochastic Fairness:
tc qdisc add dev $DEV parent 1:10 handle 10: sfq perturb 10
tc qdisc add dev $DEV parent 1:20 handle 20: sfq perturb 10

# filters: quake and ping
tc filter add dev $DEV parent 1:0 protocol ip prio 1 handle 1 fw \
flowid 1:10
tc filter add dev $DEV parent 1:0 protocol ip prio 10 u32 \
match ip protocol 1 0xff flowid 1:10
-----------------------------------------------------------

So far, so good.

The only problem I have is that, if I dont play quake, all the normal traffic gets only 90% of my line speed ($[9*$UPLINK/10] kbit). But I want that traffic to get 100%, but only if I dont play).

Ok, then i modified the 1:20 class to have a ceil statement:

-----------------------------------------------------------
tc class add dev $DEV parent 1:1 classid 1:20 htb \
rate $[9*$UPLINK/10]kbit ceil ${UPLINK}kbit \
burst 6k prio 2
-----------------------------------------------------------

In theorie everything should be fine now, 1:20 gets the whole line as long as 1:10 doesn't need any bandwidth.

Problem: I have lag in quake!

So what do you guys think?

Is there any way to limit 1:20 to exactly 90% uplink, as soon as 1:10 has activity < 10% uplink? Then quake should have enough spare bandwidth. I tried lower burst settings without luck.

Thanks for your help.

Greetings,
Bjoern

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Bjoern Metzdorf
Quoted 22 lines
# install root HTB, point default traffic to 1:20:
tc qdisc add dev $DEV root handle 1: htb default 20
tc class add dev $DEV parent 1: classid 1:1 htb rate ${UPLINK}kbit \
   burst 6k
tc class add dev $DEV parent 1:1 classid 1:10 htb rate ${UPLINK}kbit \
   burst 6k prio 1
tc class add dev $DEV parent 1:1 classid 1:20 htb \
   rate $[9*$UPLINK/10]kbit burst 6k prio 2
So far, so good.

The only problem I have is that, if I dont play quake, all the normal traffic gets only 90% of my line speed ($[9*$UPLINK/10] kbit). But I want that traffic to get 100%, but only if I dont play).

Ok, then i modified the 1:20 class to have a ceil statement:

-----------------------------------------------------------
tc class add dev $DEV parent 1:1 classid 1:20 htb \
rate $[9*$UPLINK/10]kbit ceil ${UPLINK}kbit \
burst 6k prio 2
-----------------------------------------------------------

Quoted 4 lines

In theorie everything should be fine now, 1:20 gets the whole line as long as 1:10 doesn't need any bandwidth.

Problem: I have lag in quake!

If you read the htb pages, you can find some more info about delays. You can try to give the quake class a lower prio.

Quoted 5 lines

So what do you guys think?

Is there any way to limit 1:20 to exactly 90% uplink, as soon as 1:10 has activity < 10% uplink? Then quake should have enough spare bandwidth. I tried lower burst settings without luck.

I don't think it's possible without external scripting.

Stef

Signature · 7 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/