quake3 issues
Hi,
I am using wshaper.htb from wondershaper 1.1a on 2.4.18 with htb2.
I have an adsl (german telekom) 128/768 line. I want to be able to play quake3 all the time without lag, even when there are heavy uploads going on.
I decided to use the fwmark method, then my line is not influenced at all by other minimize-delay TOS programs.
So I put marked all quake packets (-p udp --dport 20000:35000 -J MARK --set-mark 1).
Here you go:
-----------------------------------------------------------
DOWNLINK#00
UPLINK#00
DEV=eth0
# install root HTB, point default traffic to 1:20: tc qdisc add dev $DEV root handle 1: htb default 20
# shape everything at $UPLINK speed - this prevents huge queues in your
# DSL modem which destroy latency:
tc class add dev $DEV parent 1: classid 1:1 htb rate ${UPLINK}kbit \
burst 6k# high prio class 1:10:
tc class add dev $DEV parent 1:1 classid 1:10 htb rate ${UPLINK}kbit \
burst 6k prio 1# bulk & default class 1:20 - gets slightly less traffic, # and a lower priority: tc class add dev $DEV parent 1:1 classid 1:20 htb \ rate $[9*$UPLINK/10]kbit burst 6k prio 2
# all get Stochastic Fairness: tc qdisc add dev $DEV parent 1:10 handle 10: sfq perturb 10 tc qdisc add dev $DEV parent 1:20 handle 20: sfq perturb 10
# filters: quake and ping
tc filter add dev $DEV parent 1:0 protocol ip prio 1 handle 1 fw \
flowid 1:10
tc filter add dev $DEV parent 1:0 protocol ip prio 10 u32 \
match ip protocol 1 0xff flowid 1:10
-----------------------------------------------------------
So far, so good.
The only problem I have is that, if I dont play quake, all the normal traffic gets only 90% of my line speed ($[9*$UPLINK/10] kbit). But I want that traffic to get 100%, but only if I dont play).
Ok, then i modified the 1:20 class to have a ceil statement:
-----------------------------------------------------------
tc class add dev $DEV parent 1:1 classid 1:20 htb \
rate $[9*$UPLINK/10]kbit ceil ${UPLINK}kbit \
burst 6k prio 2
-----------------------------------------------------------
In theorie everything should be fine now, 1:20 gets the whole line as long as 1:10 doesn't need any bandwidth.
Problem: I have lag in quake!
So what do you guys think?
Is there any way to limit 1:20 to exactly 90% uplink, as soon as 1:10 has activity < 10% uplink? Then quake should have enough spare bandwidth. I tried lower burst settings without luck.
Thanks for your help.
Greetings,
Bjoern
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Oops,
Quoted 5 lines
Here you go:
-----------------------------------------------------------
DOWNLINK#00
UPLINK#00
DEV=eth0
This should read:
DOWNLINKv8
UPLINK8
DEV=eth0
pasted the wrong file, sorry.
Greetings,
Bjoern
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 22 lines
# install root HTB, point default traffic to 1:20: tc qdisc add dev $DEV root handle 1: htb default 20 tc class add dev $DEV parent 1: classid 1:1 htb rate ${UPLINK}kbit \ burst 6k tc class add dev $DEV parent 1:1 classid 1:10 htb rate ${UPLINK}kbit \ burst 6k prio 1 tc class add dev $DEV parent 1:1 classid 1:20 htb \ rate $[9*$UPLINK/10]kbit burst 6k prio 2 So far, so good.The only problem I have is that, if I dont play quake, all the normal traffic gets only 90% of my line speed ($[9*$UPLINK/10] kbit). But I want that traffic to get 100%, but only if I dont play).
Ok, then i modified the 1:20 class to have a ceil statement:
-----------------------------------------------------------
tc class add dev $DEV parent 1:1 classid 1:20 htb \
rate $[9*$UPLINK/10]kbit ceil ${UPLINK}kbit \
burst 6k prio 2
-----------------------------------------------------------
Quoted 4 lines
In theorie everything should be fine now, 1:20 gets the whole line as long as 1:10 doesn't need any bandwidth.
Problem: I have lag in quake!
If you read the htb pages, you can find some more info about delays. You can try to give the quake class a lower prio.
Quoted 5 lines
So what do you guys think?
Is there any way to limit 1:20 to exactly 90% uplink, as soon as 1:10 has activity < 10% uplink? Then quake should have enough spare bandwidth. I tried lower burst settings without luck.
I don't think it's possible without external scripting.
Stef
Signature · 7 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.openprojects.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/