help, a children can not borrow from a parent?
SORRY! not 12bits, should 12mbits
WHEN i send packets from 10.1.1.1 at rate frome 12mbit to 50mbit BY
using
SMARTBIT 600, the rate of class 10:100 is always 12Mbits.
Quoted 2 lines
I suppose it's the SMATRBIT 600 that says it sends 12bits. WHAT if you change 12mbit to 15mbit. WHAT if you send more then 20Mbit.
WHAT
Quoted 3 lines
if you change 12mbit to a lower value (1mbit). CAN you can do that and post the results?
I don't think there is an error in your setup.
WHEN i change 12mbit to 15mbit and send packets at rate 15mbit,20mbit,30mbit,50mbit, the rate of class 10:100 is always 15mbits. WHEN i change 12mbit to 30mbit and send packets at rate 30mbit,40mbit,50mbit, the rate of class 10:100 is always 30mbits. WHEN i change 12mbit to a lower value (1mbit) and send packets at rate 1mbit,2mbit,10mbit,20mbit, the rate of class 10:100 is always 1mbits.
Quoted 1 line
Quoted 1 line
WHEN i send packets from 10.1.1.1 at rate frome 12mbit to 50mbit BY
using
Quoted 5 lines
Quoted 2 lines
SMATRBIT 600,
the rate of class 10:100 is always 12bits.I suppose it's the SMATRBIT 600 that says it sends 12bits.
WHAT if you change 12mbit to 15mbit. WHAT if you send more then 20Mbit.
WHAT
Quoted 32 lines
if you change 12mbit to a lower value (1mbit). CAN you can do that and post the results?
I don't think there is an error in your setup.Stef
Quoted 10 lines
Quoted 10 lines
Hi ;
MY script:
tc-htb3 qdisc del dev eth2 root
ipchains -Ftc-htb3 qdisc add dev eth2 root handle 10: htb default 20 r2q 40
tc-htb3 class add dev eth2 parent 10: classid 10:1 htb rate 50Mbit
burst
Quoted 3 lines
Quoted 3 lines
2000
tc-htb3 class add dev eth2 parent 10:1 classid 10:100 htb rate 12mbit
ceil
Quoted 2 lines
Quoted 2 lines
50mbit prio 1
tc-htb3 class add dev eth2 parent 10:1 classid 10:20 htb rate 38mbitceil
Quoted 18 lines
Quoted 6 lines
Quoted 6 lines
50Mbit prio 8
ipchains -A fw -s 10.1.1.1 -m 100
ipchains -A fw -s 0.0.0.0 -d 0.0.0.0 -j ACCEPTtc-htb3 filter add dev eth2 protocol ip parent 10:0 prio 1 handle 100
fw
Quoted 9 lines
Quoted 9 lines
classid 10:100
WHEN i send packets at 20mbit from 10.1.1.1 ,
#tc -s -d qdisc show dev eth2
qdisc htb 10:
Sent 246602122 bytes 487287 pkts (dropped 323938, overlimits 1850710)#tc -s -d class show dev eth2
class htb 10:1 root prio 0 rate 50Mbit ceil 50Mbit burst 1985b/8 mpu
0b
Quoted 6 lines
Quoted 5 lines
Quoted 5 lines
cburst 67121b/8 mpu 0b quantum 0 level 7
Sent 246602122 bytes 487287 pkts (dropped 0, overlimits 0) rate 8bpsclass htb 10:100 parent 10:1 prio 1 rate 12Mbit ceil 50Mbit burst
Quoted 20 lines
17325b/8
Quoted 4 lines
Quoted 4 lines
mpu 0b cburst 67121b/8 mpu 0b quantum 39321 level 0
Sent 246552164 bytes 486503 pkts (dropped 323938, overlimits 0)class htb 10:20 parent 10:1 prio 1 rate 38Mbit ceil 50Mbit burst
51396b/8
Quoted 10 lines
Quoted 6 lines
mpu 0b cburst 67121b/8 mpu 0b quantum 124518 level 0
Sent 49958 bytes 784 pkts (dropped 0, overlimits 0) rate 8bpsa class 10:100 can not borrow from a parent 10:0 ,WHY?
How do you come to that conclustion ?????
Stef
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 16 lines · On Tuesday 22 October 2002 11:14, [email protected] wrote:
SORRY! not 12bits, should 12mbits
WHEN i send packets from 10.1.1.1 at rate frome 12mbit to 50mbit BY
using
SMARTBIT 600, the rate of class 10:100 is always 12Mbits.Quoted 2 lines
I suppose it's the SMATRBIT 600 that says it sends 12bits. WHAT if you change 12mbit to 15mbit. WHAT if you send more then 20Mbit.
WHAT
Quoted 3 lines
if you change 12mbit to a lower value (1mbit). CAN you can do that and post the results?
I don't think there is an error in your setup.
Quoted 6 lines
WHEN i change 12mbit to 15mbit and send packets at rate 15mbit,20mbit,30mbit,50mbit, the rate of class 10:100 is always 15mbits. WHEN i change 12mbit to 30mbit and send packets at rate 30mbit,40mbit,50mbit, the rate of class 10:100 is always 30mbits. WHEN i change 12mbit to a lower value (1mbit) and send packets at rate 1mbit,2mbit,10mbit,20mbit, the rate of class 10:100 is always 1mbits.
The ceil parameter always worked for me. What version of tc/htb/kernel are you using?
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/