Skip to contentSkip to conversation

a question about tc filter

LARTC Folke Aeon 2 participants 3 messages Dec 1, 2002

lore
Share & tools
lore

Folke Aeon

author
#0 lore raw

hi, all

i run the following scripts :
tc qdisc add dev eth0 handle ffff: ingress
tc filter add dev eth0 parent ffff: protocol ip \

    pref 4 u32 match ip dst 10.0.0.1 flowid :1

my question is :

can i know how many packets are matched by
this filter?
if i can , what should i do to get this
counter value, then.

thanks :)

_________________________________________________________________
MSN 8 helps eliminate e-mail viruses. Get 2 months FREE*.
http://join.msn.com/?pageþatures/virus

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 11 lines · Folke Aeon

hi, all

i run the following scripts :
tc qdisc add dev eth0 handle ffff: ingress
tc filter add dev eth0 parent ffff: protocol ip \

    pref 4 u32 match ip dst 10.0.0.1 flowid :1

my question is :

can i know how many packets are matched by
this filter?

No

Quoted 2 lines

if i can , what should i do to get this
counter value, then.

But you can make a iptables rule that matches the same packets. Iptables has builtin counters for bytes and packets.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
author
#2 lore raw
In reply to Folke Aeon

thanks :)

but what if i setup color-aware filters for AF PHB? say, there is two filters , both have to match the packets from the source ip 10.0.0.1/24 to the destination 10.0.1.1/24 , and at same time, the first one with a police rate and a burst size and a continue option, while the second one with a relatively lower priority which will match the packets excess the police rate. thus, the iptables cannot tell me the two colored-counters value respectively, it can only tell me the total packets matched by the two filters , am i right?

Quoted 25 lines

From: Stef Coene <[email protected]>
To: "Folke Aeon" <[email protected]>, [email protected]
Subject: Re: [LARTC] a question about tc filter
Date: Sun, 1 Dec 2002 10:58:50 +0100

Quoted 11 lines · Folke Aeon

hi, all

i run the following scripts :
tc qdisc add dev eth0 handle ffff: ingress
tc filter add dev eth0 parent ffff: protocol ip \

    pref 4 u32 match ip dst 10.0.0.1 flowid :1

my question is :

can i know how many packets are matched by
this filter?

No

Quoted 2 lines

if i can , what should i do to get this
counter value, then.

But you can make a iptables rule that matches the same packets. Iptables has
builtin counters for bytes and packets.

Quoted 8 lines

Stef

--

[email protected]
"Using Linux as bandwidth manager"
http://www.docum.org/
#lartc @ irc.oftc.net

_________________________________________________________________
Add photos to your e-mail with MSN 8. Get 2 months FREE*.
http://join.msn.com/?pageþatures/featuredemail

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/