Skip to contentSkip to conversation

PAS16 modules: The good, the bad, and the ugly.

DISCUSSION Kevin Turner 1 participant 1 message Jan 15, 1999 Sound

lore
Share & tools
lore
#0 lore raw

I know that lots of people have been fighting with the configuration on this one since the switch to modular sound. Here are the results of my latest battle under 2.2.0pre7.

* Things that work:

No more "Sound: DMA (output) timed out - IRQ/DRQ config error?" with current configuration when playing to /dev/dsp, audio. Happy day!

* Things that don't work:

Removing and adding the pas2 module again. This causes the Pro Audio Spectrum to be listed as Audio Device 1 instead of 0, and sounds don't play then. I have a hunch this is related to dmabuf=1, but haven't tested that. It makes configuration testing a bitch because you have to reboot. <grumble>

Playing to /dev/dsp1,audio1 works, but only plays the first bit of a clip. Then it goes silent or does the old "DMA (output) timed out" routine while clipping in and out.

Can't record from /dev/dsp1,audio1. DMA timed out etc. It may be that the emulation doesn't support this, but it would be nice if it told you so.

The PAS (not but not /dev/audio1) sometimes boots into weird moods where sound played through /dev/audio is way too fast, and dsp is noisy with our old friend "DMA (output) timed out". I haven't been able to figure out how to solve this except by cold reboot.

* Other odd stuff:

In pas2_card.c, there's a comment in detect_pas_hw that says W:1 disables warm boot reset of the card. I assume it's referring to the DOS driver mvsound.sys, but the documentation for that states that /W:1 *enables* a warm boot reset and is the default.

Note I have an Award BIOS. I don't know why this matters except the faq from spectrum says to disable warm boot reset if you have award bios. I haven't though, because I never have and the kernel source says not to.

* Configurations

==/etc/conf.modules:
# I have a ISA motherboard and over 16 MB ram. # DMA can only access the first 16 MB though, so... options sound dmabuf=1

# These things should load the sound module...
alias char-major-14 pas2
alias mixer0 pas2

# Options to pas module.
# DMA's 1-3 are 8 bit, 5-7 are 16 bit, using a 16 bit one for pas. # That might be important.
# io=0x388 is standard default for pas.
# SB parameters here are standard (sb emulation is 8 bit). options pas2 dma=5 irq io=0x388 sb_dma=1 sb_irq=5 sb_io=0x220

# To play midi files, use the adlib_card module.
alias synth0 adlib_card
# Point adlib_card module at pas ioport.
options adlib_card io=0x388

# This can use the sb emulation.
# It lets us use /dev/audio1
alias sound-slot-1 sb

# SB options for SB emulation.
# Notice that pas2=1 is NOT here,

# as I don't get "SB 2.0 detected OK (220)" that way.
options sb dma=1 irq=5 io=0x220

==/dosc/config.sys (for reference)
rem the X displays current configuration stats.
DEVICEHIGH /L:3,18480 =C:\SPECTRUM\MVSOUND.SYS D:5 Q:10 S:1,220,3,5 M:1,330,7 J:1 /W:1 X

==/proc/sound (once all relevant modules have been loaded) OSS/Free:3.8s2++-971130
Load type: Driver loaded as a module
Kernel: Linux uwanna.kompile.org 2.2.0-pre7 #1 Thu Jan 14 20:57:16 EST 1999 i486
Config options: 0

Installed drivers:

Card config:

Audio devices:
0: Pro Audio Spectrum
1: Sound Blaster (8 BIT/MONO ONLY) (2.0)

Synth devices:
0: Yamaha OPL3

Midi devices:
0: Pro Audio Spectrum
1: Sound Blaster

Timers:
0: System clock

Mixers:
0: Pro Audio Spectrum 16