PAS16 modules: The good, the bad, and the ugly.
I know that lots of people have been fighting with the configuration on this one since the switch to modular sound. Here are the results of my latest battle under 2.2.0pre7.
* Things that work:
No more "Sound: DMA (output) timed out - IRQ/DRQ config error?" with current configuration when playing to /dev/dsp, audio. Happy day!
* Things that don't work:
Removing and adding the pas2 module again. This causes the Pro Audio Spectrum to be listed as Audio Device 1 instead of 0, and sounds don't play then. I have a hunch this is related to dmabuf=1, but haven't tested that. It makes configuration testing a bitch because you have to reboot. <grumble>
Playing to /dev/dsp1,audio1 works, but only plays the first bit of a clip. Then it goes silent or does the old "DMA (output) timed out" routine while clipping in and out.
Can't record from /dev/dsp1,audio1. DMA timed out etc. It may be that the emulation doesn't support this, but it would be nice if it told you so.
The PAS (not but not /dev/audio1) sometimes boots into weird moods where sound played through /dev/audio is way too fast, and dsp is noisy with our old friend "DMA (output) timed out". I haven't been able to figure out how to solve this except by cold reboot.
* Other odd stuff:
In pas2_card.c, there's a comment in detect_pas_hw that says W:1 disables warm boot reset of the card. I assume it's referring to the DOS driver mvsound.sys, but the documentation for that states that /W:1 *enables* a warm boot reset and is the default.
Note I have an Award BIOS. I don't know why this matters except the faq from spectrum says to disable warm boot reset if you have award bios. I haven't though, because I never have and the kernel source says not to.
* Configurations
==/etc/conf.modules:
# I have a ISA motherboard and over 16 MB ram. # DMA can only access the first 16 MB though, so... options sound dmabuf=1
# These things should load the sound module...
alias char-major-14 pas2
alias mixer0 pas2
# Options to pas module.
# DMA's 1-3 are 8 bit, 5-7 are 16 bit, using a 16 bit one for pas. # That might be important.
# io=0x388 is standard default for pas.
# SB parameters here are standard (sb emulation is 8 bit). options pas2 dma=5 irq io=0x388 sb_dma=1 sb_irq=5 sb_io=0x220
# To play midi files, use the adlib_card module.
alias synth0 adlib_card
# Point adlib_card module at pas ioport.
options adlib_card io=0x388
# This can use the sb emulation.
# It lets us use /dev/audio1
alias sound-slot-1 sb
# SB options for SB emulation.
# Notice that pas2=1 is NOT here,
# as I don't get "SB 2.0 detected OK (220)" that way. options sb dma=1 irq=5 io=0x220
==/dosc/config.sys (for reference)
rem the X displays current configuration stats.
DEVICEHIGH /L:3,18480 =C:\SPECTRUM\MVSOUND.SYS D:5 Q:10 S:1,220,3,5 M:1,330,7 J:1 /W:1 X
==/proc/sound (once all relevant modules have been loaded) OSS/Free:3.8s2++-971130
Load type: Driver loaded as a module
Kernel: Linux uwanna.kompile.org 2.2.0-pre7 #1 Thu Jan 14 20:57:16 EST 1999 i486
Config options: 0
Installed drivers:
Card config:
Audio devices:
0: Pro Audio Spectrum
1: Sound Blaster (8 BIT/MONO ONLY) (2.0)
Synth devices:
0: Yamaha OPL3
Midi devices:
0: Pro Audio Spectrum
1: Sound Blaster
Timers:
0: System clock
Mixers:
0: Pro Audio Spectrum 16