ARMv7 SVC mode: PSCI not loaded and only 1st CPU core gets activated
Hi,
when building u-boot for ARMv7 with these settings for SVC mode (ie. "Secure Mode"), instead of HYPervisor mode:
ARM architecture ---> ... [*] Enable support for booting in non-secure mode [*] Boot in secure mode by default [ ] Enable support for hardware virtualization [*] Enable PSCI support (2) Maximum supported CPUs for PSCI
[ ] Use LPAE page table format
...
then only the first CPU core gets activated.
How to bring the other core(s) online?
I tried this from https://www.kernel.org/doc/html/v5.0/core-api/cpu_hotplug.html :
# echo 1 > /sys/devices/system/cpu/cpu1/online bash: /sys/devices/system/cpu/cpu1/online: Permission denied
(actually there is no "online" entry under cpu1, but also not under cpu0. Attached is the tree under /sys/devices/system/cpu/ )
#
# Automatically generated file; DO NOT EDIT.
# U-Boot 2019.04-rc4 Configuration
...CONFIG_SYS_ARCH="arm"CONFIG_SYS_CPU="armv7"CONFIG_SYS_SOC="sunxi"CONFIG_SYS_BOARD="sunxi"CONFIG_SYS_CONFIG_NAME="sun7i"
...CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-lamobo-r1"
...
# uname -a Linux r1-3 5.0.5 #1 SMP Sat Mar 30 05:34:40 CET 2019 armv7l GNU/Linux
kernel conf has CONFIG_HOTPLUG_CPU=y
# dmesg | grep -i "smp\|psci\|started in" [ 0.000000] Linux version 5.0.5 (u-ps at c22-local) (gcc version 9.0.1 20190326 (experimental) [trunk revision 269955] (GCC)) #1 SMP Sat Mar 30 05:34:40 CET 2019 [ 0.004154] smp: Bringing up secondary CPUs ... [ 0.004753] smp: Brought up 1 node, 1 CPU [ 0.004766] SMP: Total of 1 processors activated (48.00 BogoMIPS). [ 0.004772] CPU: All CPU(s) started in SVC mode.
(ie. this means that PSCI is not loaded b/c otherwise there would be some "psci" lines in the log)
# lscpu Architecture: armv7l Byte Order: Little Endian CPU(s): 2 On-line CPU(s) list: 0 Off-line CPU(s) list: 1 Thread(s) per core: 1 Core(s) per socket: 1 Socket(s): 1 Model name: ARMv7 Processor rev 4 (v7l) CPU max MHz: 960.0000 CPU min MHz: 144.0000
See also:
---------
http://linux-sunxi.org/PSCI
https://www.kernel.org/doc/Documentation/devicetree/bindings/arm/psci.txt
According to this page
https://falstaff.agner.ch/2016/07/03/u-bootlinux-and-hyp-mode-on-armv7/
it seems in older u-boot versions it did activate all CPUs in SVC mode:
"
Brought up 2 CPUs
SMP: Total of 2 processors activated (96.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
"
-------------- next part --------------/sys/devices/system/cpu/
├── cpu0 │ ├── cpu_capacity │ ├── cpufreq -> ../cpufreq/policy0 │ ├── hotplug │ │ ├── fail │ │ ├── state │ │ └── target │ ├── of_node -> ../../../../firmware/devicetree/base/cpus/cpu at 0 │ ├── power │ │ ├── autosuspend_delay_ms │ │ ├── control │ │ ├── pm_qos_resume_latency_us │ │ ├── runtime_active_time │ │ ├── runtime_status │ │ └── runtime_suspended_time │ ├── subsystem -> ../../../../bus/cpu │ ├── topology │ │ ├── core_id │ │ ├── core_siblings │ │ ├── core_siblings_list │ │ ├── physical_package_id │ │ ├── thread_siblings │ │ └── thread_siblings_list │ └── uevent ├── cpu1 │ ├── cpu_capacity │ ├── cpufreq -> ../cpufreq/policy0 │ ├── hotplug │ │ ├── fail │ │ ├── state │ │ └── target │ ├── of_node -> ../../../../firmware/devicetree/base/cpus/cpu at 1 │ ├── power │ │ ├── autosuspend_delay_ms │ │ ├── control │ │ ├── pm_qos_resume_latency_us │ │ ├── runtime_active_time │ │ ├── runtime_status │ │ └── runtime_suspended_time │ ├── subsystem -> ../../../../bus/cpu │ └── uevent ├── cpufreq │ ├── policy0 │ │ ├── affected_cpus │ │ ├── cpuinfo_cur_freq │ │ ├── cpuinfo_max_freq │ │ ├── cpuinfo_min_freq │ │ ├── cpuinfo_transition_latency │ │ ├── related_cpus │ │ ├── scaling_available_frequencies │ │ ├── scaling_available_governors │ │ ├── scaling_cur_freq │ │ ├── scaling_driver │ │ ├── scaling_governor │ │ ├── scaling_max_freq │ │ ├── scaling_min_freq │ │ ├── scaling_setspeed │ │ └── stats │ │ ├── reset │ │ ├── time_in_state │ │ ├── total_trans │ │ └── trans_table │ └── schedutil │ └── rate_limit_us ├── cpuidle │ ├── current_driver │ └── current_governor_ro ├── hotplug │ └── states ├── isolated ├── kernel_max ├── modalias ├── offline ├── online ├── possible ├── power │ ├── autosuspend_delay_ms │ ├── control │ ├── runtime_active_time │ ├── runtime_status │ └── runtime_suspended_time ├── present └── uevent
20 directories, 63 files