Skip to contentSkip to conversation

ppc4xx: Add GDsys PowerPC 440 ETX board support.

PATCH Superseded Dirk Eibach 2 participants 2 messages Dec 9, 2008 Kbuild

v4 of 7 Superseded Latest is v7 →

lore
Share & tools
lore
#0 lore raw

PATCH v4 1/1 ppc4xx: Add GDsys PowerPC 440 ETX board support.

Board support for the Guntermann & Drunck PowerPC 440 ETX module. Based on the AMCC Yosemite board support by Stefan Roese.

---

Depends on [PATCH v3] ppc4xx: Improve DDR autodetect

Removed legacy includes in board/gdsys/gdppc440etx/gdppc440etx.c. Used mfebc()/mtebc() in board/gdsys/gdppc440etx/gdppc440etx.c. Identation with tabs instead of spaces in include/configs/gdppc440etx.h.

 MAINTAINERS                           |    1 +
 MAKEALL                               |    1 +
 Makefile                              |    3 +
 board/gdsys/gdppc440etx/Makefile      |   51 +++++
 board/gdsys/gdppc440etx/config.mk     |   44 +++++
 board/gdsys/gdppc440etx/gdppc440etx.c |  325 +++++++++++++++++++++++++++++++++
 board/gdsys/gdppc440etx/init.S        |   75 ++++++++
 board/gdsys/gdppc440etx/u-boot.lds    |  144 +++++++++++++++
 include/configs/gdppc440etx.h         |  194 ++++++++++++++++++++
 9 files changed, 838 insertions(+), 0 deletions(-)
 create mode 100644 Makefile
 create mode 100644 board/gdsys/gdppc440etx/config.mk
 create mode 100644 board/gdsys/gdppc440etx/gdppc440etx.c
 create mode 100644 board/gdsys/gdppc440etx/init.S
 create mode 100644 board/gdsys/gdppc440etx/u-boot.lds
 create mode 100644 include/configs/gdppc440etx.h
MAINTAINERS +1 -0
index 127604b..b836263 100644
@@ -132,6 +132,7 @@ Jon Diekema <[email protected]>
 
 Dirk Eibach <[email protected]>
 
+	gdppc440etx	PPC440EP/GR
 	neo		PPC405EP
 
 Dave Ellis <[email protected]>
MAKEALL +1 -0
index dbed268..3789bb9 100755
@@ -188,6 +188,7 @@ LIST_4xx="		\
 	EXBITGEN	\
 	fx12mm		\
 	G2000		\
+	gdppc440etx	\
 	glacier		\
 	haleakala	\
 	haleakala_nand	\
Makefile +3 -0
index befb608..d77ab3a 100644
@@ -1315,6 +1315,9 @@ fx12mm_config: unconfig
 G2000_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx g2000
 
+gdppc440etx_config:	unconfig
+	@$(MKCONFIG) $(@:_config=) ppc ppc4xx gdppc440etx gdsys
+
 hcu4_config:	unconfig
 	@mkdir -p $(obj)board/netstal/common
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx hcu4 netstal
board/gdsys/gdppc440etx/Makefile new file +51 -0

51 lines not on this page · raw message

board/gdsys/gdppc440etx/config.mk new file +44 -0

44 lines not on this page · raw message

board/gdsys/gdppc440etx/gdppc440etx.c new file +325 -0

325 lines not on this page · raw message

board/gdsys/gdppc440etx/init.S new file +75 -0

75 lines not on this page · raw message

board/gdsys/gdppc440etx/u-boot.lds new file +144 -0

144 lines not on this page · raw message

include/configs/gdppc440etx.h new file +194 -0

194 lines not on this page · raw message

Signature · 1 line
1.5.6.5
#1 lore raw

PATCH v4 1/1 ppc4xx: Add GDsys PowerPC 440 ETX board support.

Quoted 11 lines · Dirk Eibach

Board support for the Guntermann & Drunck PowerPC 440 ETX module. Based on the AMCC Yosemite board support by Stefan Roese.

---

Depends on [PATCH v3] ppc4xx: Improve DDR autodetect

Removed legacy includes in board/gdsys/gdppc440etx/gdppc440etx.c. Used mfebc()/mtebc() in board/gdsys/gdppc440etx/gdppc440etx.c. Identation with tabs instead of spaces in include/configs/gdppc440etx.h.

Still some nitpicking comments below.

<snip>

Quoted 37 lines
include/configs/gdppc440etx.h new file +31 -0
new file mode 100644
index 0000000..edee177
@@ -0,0 +1,194 @@
+/*
+ * (C) Copyright 2008
+ * Dirk Eibach,  Guntermann & Drunck GmbH, eibach at gdsys.de
+ *
+ * Based on include/configs/yosemite.h
+ * (C) Copyright 2005-2007
+ * Stefan Roese, DENX Software Engineering, sr at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * gdppc440etx.h - configuration for G&D 440EP/GR ETX-Module
+ */
+#ifndef __CONFIG_H

include/configs/gdppc440etx.h line 41

Quoted 10 lines
include/configs/gdppc440etx.h new file +10 -0
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_440GR		1	   /* Specific PPC440GR support */
+#define CONFIG_HOSTNAME		gdppc440etx
+#define CONFIG_440		1          /* ... PPC440 family         */
+#define CONFIG_4xx		1          /* ... PPC4xx family         */
+#define CONFIG_SYS_CLK_FREQ	66666666   /* external freq to pll      */

Please use tab to indent to the comment column as well.

Quoted 68 lines
include/configs/gdppc440etx.h new file +47 -0
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
+#define CONFIG_BOARD_EARLY_INIT_F	1     /* call board_early_init_f*/
+#define CONFIG_MISC_INIT_R		1     /* call misc_init_r()     */
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_FLASH_BASE		0xfc000000  /* start of FLASH    */
+#define CONFIG_SYS_PCI_MEMBASE		0xa0000000  /* mapped pci memory */
+#define CONFIG_SYS_PCI_MEMBASE1		CONFIG_SYS_PCI_MEMBASE  + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE2		CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE3		CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
+
+/*Don't change either of these*/
+#define CONFIG_SYS_PERIPHERAL_BASE	0xef600000  /* internal peripherals */
+#define CONFIG_SYS_PCI_BASE		0xe0000000  /* internal PCI regs */
+/*Don't change either of these*/
+
+#define CONFIG_SYS_USB_DEVICE		0x50000000
+#define CONFIG_SYS_BOOT_BASE_ADDR	0xf0000000
+
+/*
+ * Initial RAM & stack pointer (placed in SDRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_DCACHE	1     /* d-cache as init ram    */
+#define CONFIG_SYS_INIT_RAM_ADDR	0x70000000 /* DCache            */
+#define CONFIG_SYS_INIT_RAM_END		(4 << 10)
+#define CONFIG_SYS_GBL_DATA_SIZE	256   /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END \
+					 - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/*
+ * Serial Port
+ */
+#define CONFIG_SYS_EXT_SERIAL_CLOCK	11059200 /* use ext. 11.059MHz clk */
+#define CONFIG_UART1_CONSOLE
+
+/*
+ * Environment
+ * Define here the location of the environment variables (FLASH or

EEPROM). + * Note: DENX encourages to use redundant environment in FLASH.
+ */

include/configs/gdppc440etx.h new file +8 -0
+#define CONFIG_ENV_IS_IN_FLASH		1  /* use FLASH for environment vars */
+
+/*
+ * FLASH related
+ */
+#define CONFIG_SYS_FLASH_CFI		    /* The flash is CFI compatible*/
+#define CONFIG_FLASH_CFI_DRIVER		    /* Use common CFI driver	*/
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET	1   /* AMD RESET for STM

29W320DB!*/ +

include/configs/gdppc440etx.h new file +4 -0
+#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max number of memory banks  */
+#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max number of sectors/chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 	120000 /* Timeout/Flash Erase (in ms)

*/ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout/Flash Write (in
ms) */ +
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1/* use buffered writes (20x faster)*/ +
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +

include/configs/gdppc440etx.h line 113

Quoted 4 lines
include/configs/gdppc440etx.h new file +4 -0
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE		0x20000 /* size of one complete sector*/
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define	CONFIG_ENV_SIZE			0x2000 /* Total Size of Env. Sector */

Space instead of tab after "#define".

Quoted 8 lines
include/configs/gdppc440etx.h new file +8 -0
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND		(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND		(CONFIG_ENV_SIZE)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
+
+/*
+ * DDR SDRAM

include/configs/gdppc440etx.h line 131

Quoted 10 lines
include/configs/gdppc440etx.h new file +10 -0
+ */
+#undef CONFIG_SPD_EEPROM		/* Don't use SPD EEPROM for setup*/
+#define CONFIG_SYS_KBYTES_SDRAM		(128 * 1024)    /* 128MB         */
+#define CONFIG_SYS_SDRAM_BANKS		(2)
+
+#define CONFIG_SDRAM_BANK0
+#define CONFIG_SDRAM_BANK1
+
+#define	CONFIG_SYS_SDRAM0_TR0		0x410a4012
+#define	CONFIG_SYS_SDRAM0_WDDCTR	0x40000000

Space instead of tab after "#define".

include/configs/gdppc440etx.h line 145

Quoted 12 lines
include/configs/gdppc440etx.h new file +12 -0
+
+#undef CONFIG_SDRAM_ECC
+
+/*
+ * I2C
+ */
+#define CONFIG_SYS_I2C_SPEED		400000 /* I2C speed+slave address*/
+
+/*
+ * Default environment variables
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS					\

Space instead of tab after "#define".

include/configs/gdppc440etx.h line 151

Quoted 6 lines
include/configs/gdppc440etx.h new file +6 -0
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
+	"kernel_addr=fc000000\0"					\
+	"ramdisk_addr=fc180000\0"					\
+	""

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================