Skip to contentSkip to conversation

S3C24XX GPIO updates

PATCH New Ben Dooks 1 participant 24 messages May 6, 2010

Subsystems (3)
lore
Share & tools
lore

Ben Dooks

author
#0 lore raw

This is the series to remove the old style s3c2410_gpio calls and move to using the central gpiolib based s3c_gpio calls.

Please test this branch on s3c24xx based systems as i've not got much access to any of the older boards.

author
#1 lore raw

PATCH 1/23 ARM: S3C24XX: Add initial s3c_gpio configuration code

Add support for s3c_gpio_setcfg() and s3c_gpio_setpull() implementations to get ready for removal of the specific code being used by s3c24xx.

Also rename the s3c_gpio_setcfg_s3c24xx_banka to s3c_gpio_setcfg_s3c24xx_a as seen in the header file to correct a build warning.

---
 arch/arm/plat-s3c24xx/Kconfig                  |    1 +
 arch/arm/plat-s3c24xx/gpiolib.c                |   17 ++++++++++++++++-
 arch/arm/plat-samsung/gpio-config.c            |    4 ++--
 arch/arm/plat-samsung/include/plat/gpio-core.h |    3 +++
 4 files changed, 22 insertions(+), 3 deletions(-)
arch/arm/plat-s3c24xx/Kconfig +1 -0
index 6e93ef8..a830fad 100644
@@ -9,6 +9,7 @@ config PLAT_S3C24XX
 	select NO_IOPORT
 	select ARCH_REQUIRE_GPIOLIB
 	select S3C_DEVICE_NAND
+	select S3C_GPIO_CFG_S3C24XX
 	help
 	  Base platform code for any Samsung S3C24XX device
 
arch/arm/plat-s3c24xx/gpiolib.c +16 -1
index 4f0f11a..376b061 100644
@@ -21,6 +21,8 @@
 #include <linux/gpio.h>
 
 #include <plat/gpio-core.h>
+#include <plat/gpio-cfg.h>
+#include <plat/gpio-cfg-helpers.h>
 #include <mach/hardware.h>
 #include <asm/irq.h>
 #include <plat/pm.h>
@@ -77,10 +79,19 @@ static int s3c24xx_gpiolib_bankg_toirq(struct gpio_chip *chip, unsigned offset)
 	return IRQ_EINT8 + offset;
 }
 
+static struct s3c_gpio_cfg s3c24xx_gpiocfg_banka = {
+	.set_config	= s3c_gpio_setcfg_s3c24xx_a,
+};
+
+struct s3c_gpio_cfg s3c24xx_gpiocfg_default = {
+	.set_config	= s3c_gpio_setcfg_s3c24xx,
+};
+
 struct s3c_gpio_chip s3c24xx_gpios[] = {
 	[0] = {
 		.base	= S3C2410_GPACON,
 		.pm	= __gpio_pm(&s3c_gpio_pm_1bit),
+		.config	= &s3c24xx_gpiocfg_banka,
 		.chip	= {
 			.base			= S3C2410_GPA(0),
 			.owner			= THIS_MODULE,
@@ -168,8 +179,12 @@ static __init int s3c24xx_gpiolib_init(void)
 	struct s3c_gpio_chip *chip = s3c24xx_gpios;
 	int gpn;
 
-	for (gpn = 0; gpn < ARRAY_SIZE(s3c24xx_gpios); gpn++, chip++)
+	for (gpn = 0; gpn < ARRAY_SIZE(s3c24xx_gpios); gpn++, chip++) {
+		if (!chip->config)
+			chip->config = &s3c24xx_gpiocfg_default;
+
 		s3c_gpiolib_add(chip);
+	}
 
 	return 0;
 }
arch/arm/plat-samsung/gpio-config.c +2 -2
index 44a84e8..c583282 100644
@@ -61,8 +61,8 @@ int s3c_gpio_setpull(unsigned int pin, s3c_gpio_pull_t pull)
 EXPORT_SYMBOL(s3c_gpio_setpull);
 
 #ifdef CONFIG_S3C_GPIO_CFG_S3C24XX
-int s3c_gpio_setcfg_s3c24xx_banka(struct s3c_gpio_chip *chip,
-				  unsigned int off, unsigned int cfg)
+int s3c_gpio_setcfg_s3c24xx_a(struct s3c_gpio_chip *chip,
+			      unsigned int off, unsigned int cfg)
 {
 	void __iomem *reg = chip->base;
 	unsigned int shift = off;
arch/arm/plat-samsung/include/plat/gpio-core.h +3 -0
index 49ff406..f0584f2 100644
@@ -108,6 +108,9 @@ extern void samsung_gpiolib_add_4bit2_chips(struct s3c_gpio_chip *chip,
 extern void samsung_gpiolib_add_4bit(struct s3c_gpio_chip *chip);
 extern void samsung_gpiolib_add_4bit2(struct s3c_gpio_chip *chip);
 
+/* exported for core SoC support to change */
+extern struct s3c_gpio_cfg s3c24xx_gpiocfg_default;
+
 #ifdef CONFIG_S3C_GPIO_TRACK
 extern struct s3c_gpio_chip *s3c_gpios[S3C_GPIO_END];
 
Signature · 1 line
1.7.0.4
author
#2 lore raw

PATCH 2/23 ARM: S3C24XX: Add the gpio pull configuration for pull-up

In reply to Ben Dooks

Add the necessary gpio configuration helper for the devices which have a single-bit pull-up resistor disabled.

---
 arch/arm/mach-s3c2410/Kconfig                      |    1 +
 arch/arm/mach-s3c2410/s3c2410.c                    |    8 +++++
 arch/arm/mach-s3c2440/Kconfig                      |    1 +
 arch/arm/mach-s3c2440/s3c2440.c                    |    8 +++++
 arch/arm/plat-samsung/gpio-config.c                |   32 ++++++++++++++++++++
 .../plat-samsung/include/plat/gpio-cfg-helpers.h   |   11 +++++++
 6 files changed, 61 insertions(+), 0 deletions(-)
arch/arm/mach-s3c2410/Kconfig +1 -0
index 5547318..9e5e96f 100644
@@ -6,6 +6,7 @@ config CPU_S3C2410
 	bool
 	depends on ARCH_S3C2410
 	select CPU_ARM920T
+	select S3C_GPIO_PULL_UP
 	select S3C2410_CLOCK
 	select S3C2410_GPIO
 	select CPU_LLSERIAL_S3C2410
arch/arm/mach-s3c2410/s3c2410.c +8 -0
index 91ba42f..adc90a3 100644
@@ -16,6 +16,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/clk.h>
 #include <linux/sysdev.h>
 #include <linux/serial_core.h>
@@ -40,6 +41,10 @@
 #include <plat/clock.h>
 #include <plat/pll.h>
 
+#include <plat/gpio-core.h>
+#include <plat/gpio-cfg.h>
+#include <plat/gpio-cfg-helpers.h>
+
 /* Initial IO mappings */
 
 static struct map_desc s3c2410_iodesc[] __initdata = {
@@ -65,6 +70,9 @@ void __init s3c2410_init_uarts(struct s3c2410_uartcfg *cfg, int no)
 
 void __init s3c2410_map_io(void)
 {
+	s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_1up;
+	s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_1up;
+
 	iotable_init(s3c2410_iodesc, ARRAY_SIZE(s3c2410_iodesc));
 }
 
arch/arm/mach-s3c2440/Kconfig +1 -0
index 7f46526..9d102b9 100644
@@ -6,6 +6,7 @@ config CPU_S3C2440
 	bool
 	depends on ARCH_S3C2410
 	select CPU_ARM920T
+	select S3C_GPIO_PULL_UP
 	select S3C2410_CLOCK
 	select S3C2410_PM if PM
 	select S3C2410_GPIO
arch/arm/mach-s3c2440/s3c2440.c +8 -0
index 2b68f7e..d50f3ae 100644
@@ -19,6 +19,7 @@
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
 #include <linux/sysdev.h>
+#include <linux/gpio.h>
 #include <linux/clk.h>
 #include <linux/io.h>
 
@@ -33,6 +34,10 @@
 #include <plat/cpu.h>
 #include <plat/s3c244x.h>
 
+#include <plat/gpio-core.h>
+#include <plat/gpio-cfg.h>
+#include <plat/gpio-cfg-helpers.h>
+
 static struct sys_device s3c2440_sysdev = {
 	.cls		= &s3c2440_sysclass,
 };
@@ -41,6 +46,9 @@ int __init s3c2440_init(void)
 {
 	printk("S3C2440: Initialising architecture\n");
 
+	s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_1up;
+	s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_1up;
+
 	/* change irq for watchdog */
 
 	s3c_device_wdt.resource[1].start = IRQ_S3C2440_WDT;
arch/arm/plat-samsung/gpio-config.c +32 -0
index c583282..8aca88d 100644
@@ -164,3 +164,35 @@ s3c_gpio_pull_t s3c_gpio_getpull_updown(struct s3c_gpio_chip *chip,
 	return (__force s3c_gpio_pull_t)pup;
 }
 #endif
+
+#ifdef CONFIG_S3C_GPIO_PULL_UP
+int s3c_gpio_setpull_1up(struct s3c_gpio_chip *chip,
+			 unsigned int off, s3c_gpio_pull_t pull)
+{
+	void __iomem *reg = chip->base + 0x08;
+	u32 pup = __raw_readl(reg);
+
+	pup = __raw_readl(reg);
+
+	if (pup == S3C_GPIO_PULL_UP)
+		pup &= ~(1 << off);
+	else if (pup == S3C_GPIO_PULL_NONE)
+		pup |= (1 << off);
+	else
+		return -EINVAL;
+
+	__raw_writel(pup, reg);
+	return 0;
+}
+
+s3c_gpio_pull_t s3c_gpio_getpull_1up(struct s3c_gpio_chip *chip,
+				     unsigned int off)
+{
+	void __iomem *reg = chip->base + 0x08;
+	u32 pup = __raw_readl(reg);
+
+	pup &= (1 << off);
+	return pup ? S3C_GPIO_PULL_NONE : S3C_GPIO_PULL_UP;
+}
+#endif /* CONFIG_S3C_GPIO_PULL_UP */
+
arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h +11 -0
index dda19da..885e9ac 100644
@@ -146,6 +146,17 @@ extern s3c_gpio_pull_t s3c_gpio_getpull_updown(struct s3c_gpio_chip *chip,
 					       unsigned int off);
 
 /**
+ * s3c_gpio_getpull_1up() - Get configuration for choice of up or none
+ * @chip: The gpio chip that the GPIO pin belongs to
+ * @off: The offset to the pin to get the configuration of.
+ *
+ * This helper function reads the state of the pull-up resistor for the
+ * given GPIO in the same case as s3c_gpio_setpull_1up.
+*/
+extern s3c_gpio_pull_t s3c_gpio_getpull_1up(struct s3c_gpio_chip *chip,
+					    unsigned int off);
+
+/**
  * s3c_gpio_setpull_s3c2443() - Pull configuration for s3c2443.
  * @chip: The gpio chip that is being configured.
  * @off: The offset for the GPIO being configured.
Signature · 1 line
1.7.0.4
author
#3 lore raw

PATCH 3/23 ARM: S3C24XX: Add extended GPIO used on S3C2443 and beyond

In reply to Ben Dooks

Add the GPIO banks that are used on the S3C2443 and above to the list of available GPIOS.

Currently we do not have any limit on the SoC GPIO, so these are being registered whether the SoC has them or not. It is currently up to the user not to try and use them.

---
 arch/arm/mach-s3c2410/include/mach/gpio-nrs.h   |   12 +++++++
 arch/arm/mach-s3c2410/include/mach/regs-gpio.h  |   17 +++++++++
 arch/arm/mach-s3c2410/include/mach/regs-gpioj.h |    4 --
 arch/arm/plat-s3c24xx/gpiolib.c                 |   41 ++++++++++++++++++++++-
 4 files changed, 69 insertions(+), 5 deletions(-)
arch/arm/mach-s3c2410/include/mach/gpio-nrs.h +12 -0
index 2edbb9c..f3182ff 100644
@@ -34,6 +34,10 @@
 #define S3C2410_GPIO_F_NR	(32)
 #define S3C2410_GPIO_G_NR	(32)
 #define S3C2410_GPIO_H_NR	(32)
+#define S3C2410_GPIO_J_NR	(32)	/* technically 16. */
+#define S3C2410_GPIO_K_NR	(32)	/* technically 16. */
+#define S3C2410_GPIO_L_NR	(32)	/* technically 15. */
+#define S3C2410_GPIO_M_NR	(32)	/* technically 2. */
 
 #if CONFIG_S3C_GPIO_SPACE != 0
 #error CONFIG_S3C_GPIO_SPACE cannot be zero at the moment
@@ -53,6 +57,10 @@ enum s3c_gpio_number {
 	S3C2410_GPIO_F_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_E),
 	S3C2410_GPIO_G_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_F),
 	S3C2410_GPIO_H_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_G),
+	S3C2410_GPIO_J_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_H),
+	S3C2410_GPIO_K_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_J),
+	S3C2410_GPIO_L_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_K),
+	S3C2410_GPIO_M_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_L),
 };
 
 #endif /* __ASSEMBLY__ */
@@ -67,6 +75,10 @@ enum s3c_gpio_number {
 #define S3C2410_GPF(_nr)	(S3C2410_GPIO_F_START + (_nr))
 #define S3C2410_GPG(_nr)	(S3C2410_GPIO_G_START + (_nr))
 #define S3C2410_GPH(_nr)	(S3C2410_GPIO_H_START + (_nr))
+#define S3C2410_GPJ(_nr)	(S3C2410_GPIO_J_START + (_nr))
+#define S3C2410_GPK(_nr)	(S3C2410_GPIO_K_START + (_nr))
+#define S3C2410_GPL(_nr)	(S3C2410_GPIO_L_START + (_nr))
+#define S3C2410_GPM(_nr)	(S3C2410_GPIO_M_START + (_nr))
 
 /* compatibility until drivers can be modified */
 
arch/arm/mach-s3c2410/include/mach/regs-gpio.h +17 -0
index fd672f3..821b966 100644
@@ -639,6 +639,23 @@
  * for the 2412/2413 from the 2410/2440/2442
 */
 
+/* S3C2443 and above */
+#define S3C2440_GPJCON	   S3C2410_GPIOREG(0xD0)
+#define S3C2440_GPJDAT	   S3C2410_GPIOREG(0xD4)
+#define S3C2440_GPJUP	   S3C2410_GPIOREG(0xD8)
+
+#define S3C2443_GPKCON	   S3C2410_GPIOREG(0xE0)
+#define S3C2443_GPKDAT	   S3C2410_GPIOREG(0xE4)
+#define S3C2443_GPKUP	   S3C2410_GPIOREG(0xE8)
+
+#define S3C2443_GPLCON	   S3C2410_GPIOREG(0xF0)
+#define S3C2443_GPLDAT	   S3C2410_GPIOREG(0xF4)
+#define S3C2443_GPLUP	   S3C2410_GPIOREG(0xF8)
+
+#define S3C2443_GPMCON	   S3C2410_GPIOREG(0x100)
+#define S3C2443_GPMDAT	   S3C2410_GPIOREG(0x104)
+#define S3C2443_GPMUP	   S3C2410_GPIOREG(0x108)
+
 /* miscellaneous control */
 #define S3C2400_MISCCR	   S3C2410_GPIOREG(0x54)
 #define S3C2410_MISCCR	   S3C2410_GPIOREG(0x80)
arch/arm/mach-s3c2410/include/mach/regs-gpioj.h +0 -4
index 1202ca5..de463bc 100644
@@ -24,10 +24,6 @@
 
 #define S3C2440_GPIO_BANKJ  (416)
 
-#define S3C2440_GPJCON	    S3C2410_GPIOREG(0xd0)
-#define S3C2440_GPJDAT	    S3C2410_GPIOREG(0xd4)
-#define S3C2440_GPJUP	    S3C2410_GPIOREG(0xd8)
-
 #define S3C2413_GPJCON		S3C2410_GPIOREG(0x80)
 #define S3C2413_GPJDAT		S3C2410_GPIOREG(0x84)
 #define S3C2413_GPJUP		S3C2410_GPIOREG(0x88)
arch/arm/plat-s3c24xx/gpiolib.c +40 -1

54 lines not on this page · raw message

Signature · 1 line
1.7.0.4
author
#4 lore raw

PATCH 4/23 ARM: H1940: Change h1940-bluetooth to use gpiolib API

In reply to Ben Dooks

Change the h1940-bluetooth driver to use gpiolib to set the output state of GPH1.

---
 arch/arm/mach-s3c2410/h1940-bluetooth.c |   16 ++++++++++++----
 1 files changed, 12 insertions(+), 4 deletions(-)
arch/arm/mach-s3c2410/h1940-bluetooth.c +12 -4
index a3f3c7b..6d06b7e 100644
@@ -33,14 +33,15 @@ static void h1940bt_enable(int on)
 		h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER);
 		/* Reset the chip */
 		mdelay(10);
-		s3c2410_gpio_setpin(S3C2410_GPH(1), 1);
+
+		gpio_set_value(S3C2410_GPH(1), 1);
 		mdelay(10);
-		s3c2410_gpio_setpin(S3C2410_GPH(1), 0);
+		gpio_set_value(S3C2410_GPH(1), 0);
 	}
 	else {
-		s3c2410_gpio_setpin(S3C2410_GPH(1), 1);
+		gpio_set_value(S3C2410_GPH(1), 1);
 		mdelay(10);
-		s3c2410_gpio_setpin(S3C2410_GPH(1), 0);
+		gpio_set_value(S3C2410_GPH(1), 0);
 		mdelay(10);
 		h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0);
 	}
@@ -61,6 +62,12 @@ static int __devinit h1940bt_probe(struct platform_device *pdev)
 	struct rfkill *rfk;
 	int ret = 0;
 
+	ret = gpio_request(S3C2410_GPH(1), dev_name(&pdev->dev));
+	if (ret) {
+		dev_err(&pdev->dev, "could not get GPH1\n");\
+		return ret;
+	}
+
 	/* Configures BT serial port GPIOs */
 	s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
 	s3c2410_gpio_pullup(S3C2410_GPH(0), 1);
@@ -100,6 +107,7 @@ static int h1940bt_remove(struct platform_device *pdev)
 	struct rfkill *rfk = platform_get_drvdata(pdev);
 
 	platform_set_drvdata(pdev, NULL);
+	gpio_free(S3C2410_GPH(1));
 
 	if (rfk) {
 		rfkill_unregister(rfk);
Signature · 1 line
1.7.0.4
author
#5 lore raw

PATCH 5/23 ARM: JIVE: Update mach-jive to use gpiolib API

In reply to Ben Dooks

Change mach-jive to use gpiolib for the GPIO lines that are directly manipulated by it.

Note, we ignore any errors from gpio_request(), unlikely to see any.

---
 arch/arm/mach-s3c2412/mach-jive.c |   19 +++++++++----------
 1 files changed, 9 insertions(+), 10 deletions(-)
arch/arm/mach-s3c2412/mach-jive.c +9 -10
index 14f4798..d2bb7d2 100644
@@ -357,8 +357,7 @@ static void jive_lcm_reset(unsigned int set)
 {
 	printk(KERN_DEBUG "%s(%d)\n", __func__, set);
 
-	s3c2410_gpio_setpin(S3C2410_GPG(13), set);
-	s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT);
+	gpio_set_value(S3C2410_GPG(13), set);
 }
 
 #undef LCD_UPPER_MARGIN
@@ -391,7 +390,7 @@ static struct ili9320_platdata jive_lcm_config = {
 
 static void jive_lcd_spi_chipselect(struct s3c2410_spigpio_info *spi, int cs)
 {
-	s3c2410_gpio_setpin(S3C2410_GPB(7), cs ? 0 : 1);
+	gpio_set_value(S3C2410_GPB(7), cs ? 0 : 1);
 }
 
 static struct s3c2410_spigpio_info jive_lcd_spi = {
@@ -413,7 +412,7 @@ static struct platform_device jive_device_lcdspi = {
 
 static void jive_wm8750_chipselect(struct s3c2410_spigpio_info *spi, int cs)
 {
-	s3c2410_gpio_setpin(S3C2410_GPH(10), cs ? 0 : 1);
+	gpio_set_value(S3C2410_GPH(10), cs ? 0 : 1);
 }
 
 static struct s3c2410_spigpio_info jive_wm8750_spi = {
@@ -636,11 +635,11 @@ static void __init jive_machine_init(void)
 
 	/* initialise the spi */
 
-	s3c2410_gpio_setpin(S3C2410_GPG(13), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT);
+	gpio_request(S3C2410_GPG(13), "lcm reset");
+	gpio_direction_output(S3C2410_GPG(13), 0);
 
-	s3c2410_gpio_setpin(S3C2410_GPB(7), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPB(7), S3C2410_GPIO_OUTPUT);
+	gpio_request(S3C2410_GPB(7), "jive spi");
+	gpio_direction_output(S3C2410_GPB(7), 1);
 
 	s3c2410_gpio_setpin(S3C2410_GPB(6), 0);
 	s3c2410_gpio_cfgpin(S3C2410_GPB(6), S3C2410_GPIO_OUTPUT);
@@ -650,8 +649,8 @@ static void __init jive_machine_init(void)
 
 	/* initialise the WM8750 spi */
 
-	s3c2410_gpio_setpin(S3C2410_GPH(10), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPH(10), S3C2410_GPIO_OUTPUT);
+	gpio_request(S3C2410_GPH(10), "jive wm8750 spi");
+	gpio_direction_output(S3C2410_GPH(10), 1);
 
 	/* Turn off suspend on both USB ports, and switch the
 	 * selectable USB port to USB device mode. */
Signature · 1 line
1.7.0.4
author
#6 lore raw

PATCH 6/23 ARM: H1940: Change mach-h1940 to use gpiolib API

In reply to Ben Dooks

Change mach-h1940 to use the gpiolib calls instead of s3c2410_gpio directly.

---
 arch/arm/mach-s3c2410/mach-h1940.c    |   15 ++++++++-------
 arch/arm/mach-s3c2412/mach-smdk2413.c |    8 ++++----
 2 files changed, 12 insertions(+), 11 deletions(-)
arch/arm/mach-s3c2410/mach-h1940.c +8 -7
index fbedd07..5527f74 100644
@@ -207,7 +207,7 @@ static int h1940_backlight_init(struct device *dev)
 {
 	gpio_request(S3C2410_GPB(0), "Backlight");
 
-	s3c2410_gpio_setpin(S3C2410_GPB(0), 0);
+	gpio_direction_output(S3C2410_GPB(0), 0);
 	s3c2410_gpio_pullup(S3C2410_GPB(0), 0);
 	s3c2410_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPB0_TOUT0);
 
@@ -216,7 +216,7 @@ static int h1940_backlight_init(struct device *dev)
 
 static void h1940_backlight_exit(struct device *dev)
 {
-	s3c2410_gpio_cfgpin(S3C2410_GPB(0), 1/*S3C2410_GPB0_OUTP*/);
+	gpio_direction_output(S3C2410_GPB(0), 1);
 }
 
 static struct platform_pwm_backlight_data backlight_data = {
@@ -245,18 +245,18 @@ static void h1940_lcd_power_set(struct plat_lcd_data *pd,
 
 	if (!power) {
 		/* set to 3ec */
-		s3c2410_gpio_setpin(S3C2410_GPC(0), 0);
+		gpio_direction_output(S3C2410_GPC(0), 0);
 		/* wait for 3ac */
 		do {
-			value = s3c2410_gpio_getpin(S3C2410_GPC(6));
+			value = gpio_get_value(S3C2410_GPC(6));
 		} while (value);
 		/* set to 38c */
-		s3c2410_gpio_setpin(S3C2410_GPC(5), 0);
+		gpio_direction_output(S3C2410_GPC(5), 0);
 	} else {
 		/* Set to 3ac */
-		s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
+		gpio_direction_output(S3C2410_GPC(5), 1);
 		/* Set to 3ad */
-		s3c2410_gpio_setpin(S3C2410_GPC(0), 1);
+		gpio_direction_output(S3C2410_GPC(0), 1);
 	}
 }
 
@@ -332,6 +332,7 @@ static void __init h1940_init(void)
 	gpio_request(S3C2410_GPC(5), "LCD power");
 	gpio_request(S3C2410_GPC(6), "LCD power");
 
+	gpio_direction_input(S3C2410_GPC(6));
 
 	platform_add_devices(h1940_devices, ARRAY_SIZE(h1940_devices));
 }
arch/arm/mach-s3c2412/mach-smdk2413.c +4 -4
index 0392065..faddb36 100644
@@ -85,10 +85,10 @@ static void smdk2413_udc_pullup(enum s3c2410_udc_cmd_e cmd)
 	switch (cmd)
 	{
 		case S3C2410_UDC_P_ENABLE :
-			s3c2410_gpio_setpin(S3C2410_GPF(2), 1);
+			gpio_set_value(S3C2410_GPF(2), 1);
 			break;
 		case S3C2410_UDC_P_DISABLE :
-			s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
+			gpio_set_value(S3C2410_GPF(2), 0);
 			break;
 		case S3C2410_UDC_P_RESET :
 			break;
@@ -134,8 +134,8 @@ static void __init smdk2413_machine_init(void)
 {	/* Turn off suspend on both USB ports, and switch the
 	 * selectable USB port to USB device mode. */
 
-	s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT);
+	WARN_ON(gpio_request(S3C2410_GPF(2), "udc pull"));
+	gpio_direction_output(S3C2410_GPF(2), 0);
 
 	s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST |
 			      S3C2410_MISCCR_USBSUSPND0 |
Signature · 1 line
1.7.0.4
author
#7 lore raw

PATCH 7/23 ARM: QT2410: Update mach-qt2410 to use gpiolib API

In reply to Ben Dooks

Change mach-qt2410.c to use gpiolib for the GPIO lines that are directly manipulated by it.

---
 arch/arm/mach-s3c2410/mach-qt2410.c |    7 ++++---
 1 files changed, 4 insertions(+), 3 deletions(-)
arch/arm/mach-s3c2410/mach-qt2410.c +4 -3
index 92a4ec3..e9762fb 100644
@@ -219,10 +219,10 @@ static void spi_gpio_cs(struct s3c2410_spigpio_info *spi, int cs)
 {
 	switch (cs) {
 	case BITBANG_CS_ACTIVE:
-		s3c2410_gpio_setpin(S3C2410_GPB(5), 0);
+		gpio_set_value(S3C2410_GPB(5), 0);
 		break;
 	case BITBANG_CS_INACTIVE:
-		s3c2410_gpio_setpin(S3C2410_GPB(5), 1);
+		gpio_set_value(S3C2410_GPB(5), 1);
 		break;
 	}
 }
@@ -353,7 +353,8 @@ static void __init qt2410_machine_init(void)
 	s3c24xx_udc_set_platdata(&qt2410_udc_cfg);
 	s3c_i2c0_set_platdata(NULL);
 
-	s3c2410_gpio_cfgpin(S3C2410_GPB(5), S3C2410_GPIO_OUTPUT);
+	WARN_ON(gpio_request(S3C2410_GPB(5), "spi cs"));
+	gpio_direction_output(S3C2410_GPB(5), 1);
 
 	platform_add_devices(qt2410_devices, ARRAY_SIZE(qt2410_devices));
 	s3c_pm_init();
Signature · 1 line
1.7.0.4
author
#8 lore raw

PATCH 8/23 ARM: n30: Update mach-n30 to use gpiolib API

In reply to Ben Dooks

Change mach-n30.c to use gpiolib for the GPIO lines that are directly manipulated by it.

---
 arch/arm/mach-s3c2410/mach-n30.c |    7 +++++--
 1 files changed, 5 insertions(+), 2 deletions(-)
arch/arm/mach-s3c2410/mach-n30.c +5 -2
index 684710f..75a9fd3 100644
@@ -86,10 +86,10 @@ static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd)
 {
 	switch (cmd) {
 	case S3C2410_UDC_P_ENABLE :
-		s3c2410_gpio_setpin(S3C2410_GPB(3), 1);
+		gpio_set_value(S3C2410_GPB(3), 1);
 		break;
 	case S3C2410_UDC_P_DISABLE :
-		s3c2410_gpio_setpin(S3C2410_GPB(3), 0);
+		gpio_set_value(S3C2410_GPB(3), 0);
 		break;
 	case S3C2410_UDC_P_RESET :
 		break;
@@ -536,6 +536,9 @@ static void __init n30_init(void)
 
 		platform_add_devices(n35_devices, ARRAY_SIZE(n35_devices));
 	}
+
+	WARN_ON(gpio_request(S3C2410_GPB(3), "udc pup"));
+	gpio_direction_output(S3C2410_GPB(3), 0);
 }
 
 MACHINE_START(N30, "Acer-N30")
Signature · 1 line
1.7.0.4
author
#9 lore raw

PATCH 9/23 ARM: BAST: Update mach-bast to use gpiolib API

In reply to Ben Dooks

Change mach-bast .c to use gpiolib for the GPIO lines that are directly manipulated by it.

---
 arch/arm/mach-s3c2410/mach-bast.c |    6 +++---
 1 files changed, 3 insertions(+), 3 deletions(-)
arch/arm/mach-s3c2410/mach-bast.c +3 -3
index 02b1b62..d03cbe2 100644
@@ -216,9 +216,7 @@ static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = {
 static int bast_pm_suspend(struct sys_device *sd, pm_message_t state)
 {
 	/* ensure that an nRESET is not generated on resume. */
-	s3c2410_gpio_setpin(S3C2410_GPA(21), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT);
-
+	gpio_direction_output(S3C2410_GPA(21), 1);
 	return 0;
 }
 
@@ -658,6 +656,8 @@ static void __init bast_init(void)
 	nor_simtec_init();
 	simtec_audio_add(NULL, true, &bast_audio);
 
+	WARN_ON(gpio_request(S3C2410_GPA(21), "bast nreset"));
+	
 	s3c_cpufreq_setboard(&bast_cpufreq);
 }
 
Signature · 1 line
1.7.0.4
author
#10 lore raw

PATCH 10/23 ARM: VR1000: Update mach-vr1000.c to use gpiolib API

In reply to Ben Dooks

Change mach-vr1000.c to use gpiolib for gpio control.

---
 arch/arm/mach-s3c2410/mach-vr1000.c |    5 +++--
 1 files changed, 3 insertions(+), 2 deletions(-)
arch/arm/mach-s3c2410/mach-vr1000.c +3 -2
index 9051f0d..d540d79 100644
@@ -357,8 +357,7 @@ static struct clk *vr1000_clocks[] __initdata = {
 
 static void vr1000_power_off(void)
 {
-	s3c2410_gpio_cfgpin(S3C2410_GPB(9), S3C2410_GPIO_OUTPUT);
-	s3c2410_gpio_setpin(S3C2410_GPB(9), 1);
+	gpio_direction_output(S3C2410_GPB(9), 1);
 }
 
 static void __init vr1000_map_io(void)
@@ -395,6 +394,8 @@ static void __init vr1000_init(void)
 
 	nor_simtec_init();
 	simtec_audio_add(NULL, true, NULL);
+
+	WARN_ON(gpio_request(S3C2410_GPB(9), "power off"));
 }
 
 MACHINE_START(VR1000, "Thorcom-VR1000")
Signature · 1 line
1.7.0.4
author
#11 lore raw

PATCH 11/23 ARM: S3C2410: Change s3c2410_gpio_pullupl(x, 1) to use s3c_gpio_cfgpull()

In reply to Ben Dooks

Start moving code that is using the old s3c2410_gpio API to using the newer s3c_gpio variants by finding all the usages of s3c2410_gpio_pullup() which disable the pin's pull up and replacing them.

sed 's/s3c2410_gpio_pullup\(.*\), 1/s3c_gpio_cfgpull\1, S3C_GPIO_PULL_NONE/g'

---
 arch/arm/mach-s3c2410/h1940-bluetooth.c |    8 ++++----
 1 files changed, 4 insertions(+), 4 deletions(-)
arch/arm/mach-s3c2410/h1940-bluetooth.c +4 -4
index 6d06b7e..171a7c3 100644
@@ -70,13 +70,13 @@ static int __devinit h1940bt_probe(struct platform_device *pdev)
 
 	/* Configures BT serial port GPIOs */
 	s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
-	s3c2410_gpio_pullup(S3C2410_GPH(0), 1);
+	s3c_gpio_cfgpull(S3C2410_GPH(0), S3C_GPIO_PULL_NONE);
 	s3c2410_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT);
-	s3c2410_gpio_pullup(S3C2410_GPH(1), 1);
+	s3c_gpio_cfgpull(S3C2410_GPH(1), S3C_GPIO_PULL_NONE);
 	s3c2410_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
-	s3c2410_gpio_pullup(S3C2410_GPH(2), 1);
+	s3c_gpio_cfgpull(S3C2410_GPH(2), S3C_GPIO_PULL_NONE);
 	s3c2410_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
-	s3c2410_gpio_pullup(S3C2410_GPH(3), 1);
+	s3c_gpio_cfgpull(S3C2410_GPH(3), S3C_GPIO_PULL_NONE);
 
 
 	rfk = rfkill_alloc(DRV_NAME, &pdev->dev, RFKILL_TYPE_BLUETOOTH,
Signature · 1 line
1.7.0.4
author
#12 lore raw

PATCH 12/23 ARM: S3C24XX: Change s3c2410_gpio_pullupl(x, 1) to use s3c_gpio_cfgpull()

In reply to Ben Dooks

Start moving code that is using the old s3c2410_gpio API to using the newer s3c_gpio variants by finding all the usages of s3c2410_gpio_pullup() which disable the pin's pull up and replacing them.

sed 's/s3c2410_gpio_pullup\(.*\), 1/s3c_gpio_cfgpull\1, S3C_GPIO_PULL_NONE/g'

---
 arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c |    6 +++---
 arch/arm/plat-s3c24xx/spi-bus1-gpd8_9_10.c   |    6 +++---
 arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c    |    6 +++---
 3 files changed, 9 insertions(+), 9 deletions(-)
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c +3 -3
index da7a617..71256ad 100644
@@ -29,8 +29,8 @@ void s3c24xx_spi_gpiocfg_bus0_gpe11_12_13(struct s3c2410_spi_info *spi,
 	} else {
 		s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPIO_INPUT);
 		s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_pullup(S3C2410_GPE(11), 1);
-		s3c2410_gpio_pullup(S3C2410_GPE(12), 1);
-		s3c2410_gpio_pullup(S3C2410_GPE(13), 1);
+		s3c_gpio_cfgpull(S3C2410_GPE(11), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPE(12), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPE(13), S3C_GPIO_PULL_NONE);
 	}
 }
arch/arm/plat-s3c24xx/spi-bus1-gpd8_9_10.c +3 -3
index 89fcf53..31bda55 100644
@@ -31,8 +31,8 @@ void s3c24xx_spi_gpiocfg_bus1_gpd8_9_10(struct s3c2410_spi_info *spi,
 	} else {
 		s3c2410_gpio_cfgpin(S3C2410_GPD(8), S3C2410_GPIO_INPUT);
 		s3c2410_gpio_cfgpin(S3C2410_GPD(9), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_pullup(S3C2410_GPD(10), 1);
-		s3c2410_gpio_pullup(S3C2410_GPD(9), 1);
-		s3c2410_gpio_pullup(S3C2410_GPD(8), 1);
+		s3c_gpio_cfgpull(S3C2410_GPD(10), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPD(9), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPD(8), S3C_GPIO_PULL_NONE);
 	}
 }
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c +3 -3
index 86b9edc..7910501 100644
@@ -29,8 +29,8 @@ void s3c24xx_spi_gpiocfg_bus1_gpg5_6_7(struct s3c2410_spi_info *spi,
 	} else {
 		s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPIO_INPUT);
 		s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_pullup(S3C2410_GPG(5), 1);
-		s3c2410_gpio_pullup(S3C2410_GPG(6), 1);
-		s3c2410_gpio_pullup(S3C2410_GPG(7), 1);
+		s3c_gpio_cfgpull(S3C2410_GPG(5), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPG(6), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPG(7), S3C_GPIO_PULL_NONE);
 	}
 }
Signature · 1 line
1.7.0.4
author
#13 lore raw

PATCH 13/23 ARM: S3C24XX: Drop s3c2410 specific s3c2410_gpio_cfgpin()

In reply to Ben Dooks

The s3c_gpio_cfgpin() call should be functionally equivalent, so replace the s3c2410_gpio_cfgpin() calls in the s3c24xx code with s3c_gpio_cfgpin to allow moving away from a fixed GPIO number to register address mapping

---
 arch/arm/mach-s3c2410/h1940-bluetooth.c      |    8 ++++----
 arch/arm/mach-s3c2410/mach-amlm5900.c        |    3 ++-
 arch/arm/mach-s3c2410/mach-bast.c            |    3 ++-
 arch/arm/mach-s3c2410/mach-h1940.c           |    3 ++-
 arch/arm/mach-s3c2410/mach-qt2410.c          |    3 ++-
 arch/arm/mach-s3c2412/mach-jive.c            |    7 ++++---
 arch/arm/mach-s3c2440/mach-mini2440.c        |   11 ++++++-----
 arch/arm/mach-s3c2440/mach-nexcoder.c        |    9 +++++----
 arch/arm/mach-s3c2440/mach-osiris.c          |    5 +++--
 arch/arm/plat-s3c24xx/common-smdk.c          |    9 +++++----
 arch/arm/plat-s3c24xx/pm.c                   |    3 ++-
 arch/arm/plat-s3c24xx/setup-i2c.c            |    5 +++--
 arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c |   10 +++++-----
 arch/arm/plat-s3c24xx/spi-bus1-gpd8_9_10.c   |   10 +++++-----
 arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c    |   10 +++++-----
 15 files changed, 55 insertions(+), 44 deletions(-)
arch/arm/mach-s3c2410/h1940-bluetooth.c +4 -4
index 171a7c3..8cdeb14 100644
@@ -69,13 +69,13 @@ static int __devinit h1940bt_probe(struct platform_device *pdev)
 	}
 
 	/* Configures BT serial port GPIOs */
-	s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
+	s3c_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
 	s3c_gpio_cfgpull(S3C2410_GPH(0), S3C_GPIO_PULL_NONE);
-	s3c2410_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT);
 	s3c_gpio_cfgpull(S3C2410_GPH(1), S3C_GPIO_PULL_NONE);
-	s3c2410_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
+	s3c_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
 	s3c_gpio_cfgpull(S3C2410_GPH(2), S3C_GPIO_PULL_NONE);
-	s3c2410_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
+	s3c_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
 	s3c_gpio_cfgpull(S3C2410_GPH(3), S3C_GPIO_PULL_NONE);
 
 
arch/arm/mach-s3c2410/mach-amlm5900.c +2 -1
index 7047317..b42a760 100644
@@ -56,6 +56,7 @@
 #include <plat/iic.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
+#include <plat/gpio-cfg.h>
 
 #ifdef CONFIG_MTD_PARTITIONS
 
@@ -225,7 +226,7 @@ static void amlm5900_init_pm(void)
 	} else {
 		enable_irq_wake(IRQ_EINT9);
 		/* configure the suspend/resume status pin */
-		s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT);
+		s3c_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT);
 		s3c2410_gpio_pullup(S3C2410_GPF(2), 0);
 	}
 }
arch/arm/mach-s3c2410/mach-bast.c +2 -1
index d03cbe2..b061ddc 100644
@@ -61,6 +61,7 @@
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/cpu-freq.h>
+#include <plat/gpio-cfg.h>
 #include <plat/audio-simtec.h>
 
 #include "usb-simtec.h"
@@ -222,7 +223,7 @@ static int bast_pm_suspend(struct sys_device *sd, pm_message_t state)
 
 static int bast_pm_resume(struct sys_device *sd)
 {
-	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
+	s3c_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
 	return 0;
 }
 
arch/arm/mach-s3c2410/mach-h1940.c +2 -1
index 5527f74..e2f7e64 100644
@@ -50,6 +50,7 @@
 #include <plat/udc.h>
 #include <plat/iic.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
@@ -209,7 +210,7 @@ static int h1940_backlight_init(struct device *dev)
 
 	gpio_direction_output(S3C2410_GPB(0), 0);
 	s3c2410_gpio_pullup(S3C2410_GPB(0), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPB0_TOUT0);
+	s3c_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPB0_TOUT0);
 
 	return 0;
 }
arch/arm/mach-s3c2410/mach-qt2410.c +2 -1
index e9762fb..d0e87b6 100644
@@ -58,6 +58,7 @@
 #include <plat/iic.h>
 
 #include <plat/common-smdk.h>
+#include <plat/gpio-cfg.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/pm.h>
@@ -347,7 +348,7 @@ static void __init qt2410_machine_init(void)
 	}
 	s3c24xx_fb_set_platdata(&qt2410_fb_info);
 
-	s3c2410_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPIO_OUTPUT);
 	s3c2410_gpio_setpin(S3C2410_GPB(0), 1);
 
 	s3c24xx_udc_set_platdata(&qt2410_udc_cfg);
arch/arm/mach-s3c2412/mach-jive.c +4 -3
index d2bb7d2..4316018 100644
@@ -48,6 +48,7 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
@@ -530,7 +531,7 @@ static void jive_power_off(void)
 	printk(KERN_INFO "powering system down...\n");
 
 	s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
 }
 
 static void __init jive_machine_init(void)
@@ -642,10 +643,10 @@ static void __init jive_machine_init(void)
 	gpio_direction_output(S3C2410_GPB(7), 1);
 
 	s3c2410_gpio_setpin(S3C2410_GPB(6), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPB(6), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPB(6), S3C2410_GPIO_OUTPUT);
 
 	s3c2410_gpio_setpin(S3C2410_GPG(8), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPG(8), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPG(8), S3C2410_GPIO_OUTPUT);
 
 	/* initialise the WM8750 spi */
 
arch/arm/mach-s3c2440/mach-mini2440.c +6 -5
index 571b176..362a2f9 100644
@@ -53,6 +53,7 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
@@ -632,24 +633,24 @@ static void __init mini2440_init(void)
 	mini2440_parse_features(&features, mini2440_features_str);
 
 	/* turn LCD on */
-	s3c2410_gpio_cfgpin(S3C2410_GPC(0), S3C2410_GPC0_LEND);
+	s3c_gpio_cfgpin(S3C2410_GPC(0), S3C2410_GPC0_LEND);
 
 	/* Turn the backlight early on */
 	s3c2410_gpio_setpin(S3C2410_GPG(4), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPG(4), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPG(4), S3C2410_GPIO_OUTPUT);
 
 	/* remove pullup on optional PWM backlight -- unused on 3.5 and 7"s */
 	s3c2410_gpio_pullup(S3C2410_GPB(1), 0);
 	s3c2410_gpio_setpin(S3C2410_GPB(1), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPB(1), S3C2410_GPIO_INPUT);
+	s3c_gpio_cfgpin(S3C2410_GPB(1), S3C2410_GPIO_INPUT);
 
 	/* Make sure the D+ pullup pin is output */
-	s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
 
 	/* mark the key as input, without pullups (there is one on the board) */
 	for (i = 0; i < ARRAY_SIZE(mini2440_buttons); i++) {
 		s3c2410_gpio_pullup(mini2440_buttons[i].gpio, 0);
-		s3c2410_gpio_cfgpin(mini2440_buttons[i].gpio,
+		s3c_gpio_cfgpin(mini2440_buttons[i].gpio,
 					S3C2410_GPIO_INPUT);
 	}
 	if (features.lcd_index != -1) {
arch/arm/mach-s3c2440/mach-nexcoder.c +5 -4
index 3420415..3ff62de 100644
@@ -40,6 +40,7 @@
 #include <plat/regs-serial.h>
 #include <plat/iic.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/s3c2410.h>
 #include <plat/s3c244x.h>
 #include <plat/clock.h>
@@ -122,15 +123,15 @@ static void __init nexcoder_sensorboard_init(void)
 {
 	// Initialize SCCB bus
 	s3c2410_gpio_setpin(S3C2410_GPE(14), 1); // IICSCL
-	s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPIO_OUTPUT);
 	s3c2410_gpio_setpin(S3C2410_GPE(15), 1); // IICSDA
-	s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPIO_OUTPUT);
 
 	// Power up the sensor board
 	s3c2410_gpio_setpin(S3C2410_GPF(1), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(1), S3C2410_GPIO_OUTPUT); // CAM_GPIO7 => nLDO_PWRDN
+	s3c_gpio_cfgpin(S3C2410_GPF(1), S3C2410_GPIO_OUTPUT); // CAM_GPIO7 => nLDO_PWRDN
 	s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); // CAM_GPIO6 => CAM_PWRDN
+	s3c_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); // CAM_GPIO6 => CAM_PWRDN
 }
 
 static void __init nexcoder_map_io(void)
arch/arm/mach-s3c2440/mach-osiris.c +3 -2
index f35371d..319458d 100644
@@ -49,6 +49,7 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
@@ -298,7 +299,7 @@ static int osiris_pm_suspend(struct sys_device *sd, pm_message_t state)
 
 	/* ensure that an nRESET is not generated on resume. */
 	s3c2410_gpio_setpin(S3C2410_GPA(21), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT);
 
 	return 0;
 }
@@ -310,7 +311,7 @@ static int osiris_pm_resume(struct sys_device *sd)
 
 	__raw_writeb(pm_osiris_ctrl0, OSIRIS_VA_CTRL0);
 
-	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
+	s3c_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
 
 	return 0;
 }
arch/arm/plat-s3c24xx/common-smdk.c +5 -4
index 9e0e20a..7b44d0c 100644
@@ -42,6 +42,7 @@
 #include <plat/nand.h>
 
 #include <plat/common-smdk.h>
+#include <plat/gpio-cfg.h>
 #include <plat/devs.h>
 #include <plat/pm.h>
 
@@ -185,10 +186,10 @@ void __init smdk_machine_init(void)
 {
 	/* Configure the LEDs (even if we have no LED support)*/
 
-	s3c2410_gpio_cfgpin(S3C2410_GPF(4), S3C2410_GPIO_OUTPUT);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(5), S3C2410_GPIO_OUTPUT);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(6), S3C2410_GPIO_OUTPUT);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(7), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPF(4), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPF(5), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPF(6), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPF(7), S3C2410_GPIO_OUTPUT);
 
 	s3c2410_gpio_setpin(S3C2410_GPF(4), 1);
 	s3c2410_gpio_setpin(S3C2410_GPF(5), 1);
arch/arm/plat-s3c24xx/pm.c +2 -1
index 3620dd2..37ea822 100644
@@ -43,6 +43,7 @@
 
 #include <asm/mach/time.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/pm.h>
 
 #define PFX "s3c24xx-pm: "
@@ -105,7 +106,7 @@ static void s3c_pm_check_resume_pin(unsigned int pin, unsigned int irqoffs)
 	} else {
 		if (pinstate == S3C2410_GPIO_IRQ) {
 			S3C_PMDBG("Disabling IRQ %d (pin %d)\n", irq, pin);
-			s3c2410_gpio_cfgpin(pin, S3C2410_GPIO_INPUT);
+			s3c_gpio_cfgpin(pin, S3C2410_GPIO_INPUT);
 		}
 	}
 }
arch/arm/plat-s3c24xx/setup-i2c.c +3 -2
index 71a6acc..9e90a7c 100644
@@ -15,12 +15,13 @@
 
 struct platform_device;
 
+#include <plat/gpio-cfg.h>
 #include <plat/iic.h>
 #include <mach/hardware.h>
 #include <mach/regs-gpio.h>
 
 void s3c_i2c0_cfg_gpio(struct platform_device *dev)
 {
-	s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPE15_IICSDA);
-	s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPE14_IICSCL);
+	s3c_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPE15_IICSDA);
+	s3c_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPE14_IICSCL);
 }
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c +5 -5
index 71256ad..9793544 100644
@@ -21,14 +21,14 @@ void s3c24xx_spi_gpiocfg_bus0_gpe11_12_13(struct s3c2410_spi_info *spi,
 					  int enable)
 {
 	if (enable) {
-		s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPE13_SPICLK0);
-		s3c2410_gpio_cfgpin(S3C2410_GPE(12), S3C2410_GPE12_SPIMOSI0);
-		s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPE11_SPIMISO0);
+		s3c_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPE13_SPICLK0);
+		s3c_gpio_cfgpin(S3C2410_GPE(12), S3C2410_GPE12_SPIMOSI0);
+		s3c_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPE11_SPIMISO0);
 		s3c2410_gpio_pullup(S3C2410_GPE(11), 0);
 		s3c2410_gpio_pullup(S3C2410_GPE(13), 0);
 	} else {
-		s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPIO_INPUT);
 		s3c_gpio_cfgpull(S3C2410_GPE(11), S3C_GPIO_PULL_NONE);
 		s3c_gpio_cfgpull(S3C2410_GPE(12), S3C_GPIO_PULL_NONE);
 		s3c_gpio_cfgpull(S3C2410_GPE(13), S3C_GPIO_PULL_NONE);
arch/arm/plat-s3c24xx/spi-bus1-gpd8_9_10.c +5 -5
index 31bda55..db9e9e4 100644
@@ -23,14 +23,14 @@ void s3c24xx_spi_gpiocfg_bus1_gpd8_9_10(struct s3c2410_spi_info *spi,
 
 	printk(KERN_INFO "%s(%d)\n", __func__, enable);
 	if (enable) {
-		s3c2410_gpio_cfgpin(S3C2410_GPD(10), S3C2440_GPD10_SPICLK1);
-		s3c2410_gpio_cfgpin(S3C2410_GPD(9), S3C2440_GPD9_SPIMOSI1);
-		s3c2410_gpio_cfgpin(S3C2410_GPD(8), S3C2440_GPD8_SPIMISO1);
+		s3c_gpio_cfgpin(S3C2410_GPD(10), S3C2440_GPD10_SPICLK1);
+		s3c_gpio_cfgpin(S3C2410_GPD(9), S3C2440_GPD9_SPIMOSI1);
+		s3c_gpio_cfgpin(S3C2410_GPD(8), S3C2440_GPD8_SPIMISO1);
 		s3c2410_gpio_pullup(S3C2410_GPD(10), 0);
 		s3c2410_gpio_pullup(S3C2410_GPD(9), 0);
 	} else {
-		s3c2410_gpio_cfgpin(S3C2410_GPD(8), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_cfgpin(S3C2410_GPD(9), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpin(S3C2410_GPD(8), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpin(S3C2410_GPD(9), S3C2410_GPIO_INPUT);
 		s3c_gpio_cfgpull(S3C2410_GPD(10), S3C_GPIO_PULL_NONE);
 		s3c_gpio_cfgpull(S3C2410_GPD(9), S3C_GPIO_PULL_NONE);
 		s3c_gpio_cfgpull(S3C2410_GPD(8), S3C_GPIO_PULL_NONE);
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c +5 -5
index 7910501..8ea663a 100644
@@ -21,14 +21,14 @@ void s3c24xx_spi_gpiocfg_bus1_gpg5_6_7(struct s3c2410_spi_info *spi,
 				       int enable)
 {
 	if (enable) {
-		s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPG7_SPICLK1);
-		s3c2410_gpio_cfgpin(S3C2410_GPG(6), S3C2410_GPG6_SPIMOSI1);
-		s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPG5_SPIMISO1);
+		s3c_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPG7_SPICLK1);
+		s3c_gpio_cfgpin(S3C2410_GPG(6), S3C2410_GPG6_SPIMOSI1);
+		s3c_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPG5_SPIMISO1);
 		s3c2410_gpio_pullup(S3C2410_GPG(5), 0);
 		s3c2410_gpio_pullup(S3C2410_GPG(6), 0);
 	} else {
-		s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPIO_INPUT);
 		s3c_gpio_cfgpull(S3C2410_GPG(5), S3C_GPIO_PULL_NONE);
 		s3c_gpio_cfgpull(S3C2410_GPG(6), S3C_GPIO_PULL_NONE);
 		s3c_gpio_cfgpull(S3C2410_GPG(7), S3C_GPIO_PULL_NONE);
Signature · 1 line
1.7.0.4
author
#14 lore raw

PATCH 14/23 ARM: S3C24XX: Remove s3c2410_gpio_setcfg()

In reply to Ben Dooks

Remove the implementation of s3c2410_gpio_setcfg() as it should now be functionally equivalent to s3c_gpio_cfgpin(), and add a wrapper for those drivers that are still using this call.

---
 arch/arm/mach-s3c2410/include/mach/gpio-fns.h |   35 ++++++++++++------
 arch/arm/plat-s3c24xx/gpio.c                  |   48 -------------------------
 2 files changed, 24 insertions(+), 59 deletions(-)
arch/arm/mach-s3c2410/include/mach/gpio-fns.h +24 -11
index 035a493..f50c2a5 100644
@@ -10,14 +10,28 @@
  * published by the Free Software Foundation.
 */
 
+#ifndef __MACH_GPIO_FNS_H
+#define __MACH_GPIO_FNS_H __FILE__
+
 /* These functions are in the to-be-removed category and it is strongly
  * encouraged not to use these in new code. They will be marked deprecated
  * very soon.
  *
  * Most of the functionality can be either replaced by the gpiocfg calls
  * for the s3c platform or by the generic GPIOlib API.
+ *
+ * As of 2.6.35-rc, these will be removed, with the few drivers using them
+ * either replaced or given a wrapper until the calls can be removed.
 */
 
+#include <plat/gpio-cfg.h>
+
+static inline void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int cfg)
+{
+	/* 1:1 mapping between cfgpin and setcfg calls at the moment */
+	s3c_gpio_cfgpin(pin, cfg);
+}
+
 /* external functions for GPIO support
  *
  * These allow various different clients to access the same GPIO
@@ -25,17 +39,6 @@
  * GPIO register, then it is safe to ioremap/__raw_{read|write} to it.
 */
 
-/* s3c2410_gpio_cfgpin
- *
- * set the configuration of the given pin to the value passed.
- *
- * eg:
- *    s3c2410_gpio_cfgpin(S3C2410_GPA(0), S3C2410_GPA0_ADDR0);
- *    s3c2410_gpio_cfgpin(S3C2410_GPE(8), S3C2410_GPE8_SDDAT1);
-*/
-
-extern void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function);
-
 extern unsigned int s3c2410_gpio_getcfg(unsigned int pin);
 
 /* s3c2410_gpio_getirq
@@ -73,6 +76,14 @@ extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
 
 /* s3c2410_gpio_pullup
  *
+ * This call should be replaced with s3c_gpio_setpull().
+ *
+ * As a note, there is currently no distinction between pull-up and pull-down
+ * in the s3c24xx series devices with only an on/off configuration.
+ */
+
+/* s3c2410_gpio_pullup
+ *
  * configure the pull-up control on the given pin
  *
  * to = 1 => disable the pull-up
@@ -101,3 +112,5 @@ extern int s3c2410_gpio_getpull(unsigned int pin);
 extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to);
 
 extern unsigned int s3c2410_gpio_getpin(unsigned int pin);
+
+#endif /* __MACH_GPIO_FNS_H */
arch/arm/plat-s3c24xx/gpio.c +0 -48

54 lines not on this page · raw message

Signature · 1 line
1.7.0.4
author
#15 lore raw

PATCH 15/23 ARM: S3C24XX: Remove s3c2410_gpio_getpull()

In reply to Ben Dooks

Remove the unused s3c2410_gpio_getpull()

---
 arch/arm/mach-s3c2410/include/mach/gpio-fns.h |   12 ------------
 arch/arm/plat-s3c24xx/gpio.c                  |   13 -------------
 2 files changed, 0 insertions(+), 25 deletions(-)
arch/arm/mach-s3c2410/include/mach/gpio-fns.h +0 -12
index f50c2a5..f453c4f 100644
@@ -97,18 +97,6 @@ extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
 
 extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to);
 
-/* s3c2410_gpio_getpull
- *
- * Read the state of the pull-up on a given pin
- *
- * return:
- *	< 0 => error code
- *	  0 => enabled
- *	  1 => disabled
-*/
-
-extern int s3c2410_gpio_getpull(unsigned int pin);
-
 extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to);
 
 extern unsigned int s3c2410_gpio_getpin(unsigned int pin);
arch/arm/plat-s3c24xx/gpio.c +0 -13
index 0b3b2cb..9b3d74c 100644
@@ -20,7 +20,6 @@
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */
 
-
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/module.h>
@@ -75,18 +74,6 @@ void s3c2410_gpio_pullup(unsigned int pin, unsigned int to)
 
 EXPORT_SYMBOL(s3c2410_gpio_pullup);
 
-int s3c2410_gpio_getpull(unsigned int pin)
-{
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
-
-	if (pin < S3C2410_GPIO_BANKB)
-		return -EINVAL;
-
-	return (__raw_readl(base + 0x08) & (1L << offs)) ? 1 : 0;
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_getpull);
 
 void s3c2410_gpio_setpin(unsigned int pin, unsigned int to)
 {
Signature · 1 line
1.7.0.4
author
#16 lore raw

PATCH 16/23 ARM: S3C24XX: Remove s3c2410_gpio_getirq()

In reply to Ben Dooks

Remove s3c2410_gpio_getirq() as the only users is the pm code, and it can be replicated by using gpio_to_irq().

---
 arch/arm/plat-s3c24xx/gpio.c |   19 -------------------
 arch/arm/plat-s3c24xx/pm.c   |    2 +-
 2 files changed, 1 insertions(+), 20 deletions(-)
arch/arm/plat-s3c24xx/gpio.c +0 -19
index 9b3d74c..24c0047 100644
@@ -120,22 +120,3 @@ unsigned int s3c2410_modify_misccr(unsigned int clear, unsigned int change)
 }
 
 EXPORT_SYMBOL(s3c2410_modify_misccr);
-
-int s3c2410_gpio_getirq(unsigned int pin)
-{
-	if (pin < S3C2410_GPF(0) || pin > S3C2410_GPG(15))
-		return -EINVAL;	/* not valid interrupts */
-
-	if (pin < S3C2410_GPG(0) && pin > S3C2410_GPF(7))
-		return -EINVAL;	/* not valid pin */
-
-	if (pin < S3C2410_GPF(4))
-		return (pin - S3C2410_GPF(0)) + IRQ_EINT0;
-
-	if (pin < S3C2410_GPG(0))
-		return (pin - S3C2410_GPF(4)) + IRQ_EINT4;
-
-	return (pin - S3C2410_GPG(0)) + IRQ_EINT8;
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_getirq);
arch/arm/plat-s3c24xx/pm.c +1 -1
index 37ea822..691fecc 100644
@@ -91,7 +91,7 @@ static void s3c_pm_check_resume_pin(unsigned int pin, unsigned int irqoffs)
 {
 	unsigned long irqstate;
 	unsigned long pinstate;
-	int irq = s3c2410_gpio_getirq(pin);
+	int irq = gpio_to_irq(pin);
 
 	if (irqoffs < 4)
 		irqstate = s3c_irqwake_intmask & (1L<<irqoffs);
Signature · 1 line
1.7.0.4
author
#17 lore raw

PATCH 17/23 ARM: SAMSUNG: Add GPIO configuration read calls

In reply to Ben Dooks

Add the necessary 1,2 and 4 bit configuration read calls for the new gpio code to allow removal of the old s3c24xx gpio code.

---
 arch/arm/mach-s3c64xx/gpiolib.c                    |    6 +++
 arch/arm/mach-s5p6440/gpio.c                       |    5 ++
 arch/arm/plat-s3c24xx/gpiolib.c                    |    2 +
 arch/arm/plat-samsung/gpio-config.c                |   47 +++++++++++++++++++-
 .../plat-samsung/include/plat/gpio-cfg-helpers.h   |   41 +++++++++++++++++
 5 files changed, 100 insertions(+), 1 deletions(-)
arch/arm/mach-s3c64xx/gpiolib.c +6 -0
index 66e6794..60c929a 100644
@@ -51,6 +51,7 @@
 
 static struct s3c_gpio_cfg gpio_4bit_cfg_noint = {
 	.set_config	= s3c_gpio_setcfg_s3c64xx_4bit,
+	.get_config	= s3c_gpio_getcfg_s3c64xx_4bit,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
 };
@@ -58,12 +59,14 @@ static struct s3c_gpio_cfg gpio_4bit_cfg_noint = {
 static struct s3c_gpio_cfg gpio_4bit_cfg_eint0111 = {
 	.cfg_eint	= 7,
 	.set_config	= s3c_gpio_setcfg_s3c64xx_4bit,
+	.get_config	= s3c_gpio_getcfg_s3c64xx_4bit,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
 };
 
 static struct s3c_gpio_cfg gpio_4bit_cfg_eint0011 = {
 	.cfg_eint	= 3,
+	.get_config	= s3c_gpio_getcfg_s3c64xx_4bit,
 	.set_config	= s3c_gpio_setcfg_s3c64xx_4bit,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
@@ -171,6 +174,7 @@ static struct s3c_gpio_chip gpio_4bit2[] = {
 
 static struct s3c_gpio_cfg gpio_2bit_cfg_noint = {
 	.set_config	= s3c_gpio_setcfg_s3c24xx,
+	.get_config	= s3c_gpio_getcfg_s3c24xx,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
 };
@@ -178,6 +182,7 @@ static struct s3c_gpio_cfg gpio_2bit_cfg_noint = {
 static struct s3c_gpio_cfg gpio_2bit_cfg_eint10 = {
 	.cfg_eint	= 2,
 	.set_config	= s3c_gpio_setcfg_s3c24xx,
+	.get_config	= s3c_gpio_getcfg_s3c24xx,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
 };
@@ -185,6 +190,7 @@ static struct s3c_gpio_cfg gpio_2bit_cfg_eint10 = {
 static struct s3c_gpio_cfg gpio_2bit_cfg_eint11 = {
 	.cfg_eint	= 3,
 	.set_config	= s3c_gpio_setcfg_s3c24xx,
+	.get_config	= s3c_gpio_getcfg_s3c24xx,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
 };
arch/arm/mach-s5p6440/gpio.c +5 -0
index b0ea741..262dc75 100644
@@ -161,12 +161,15 @@ static struct s3c_gpio_cfg s5p6440_gpio_cfgs[] = {
 	}, {
 		.cfg_eint	= 0,
 		.set_config	= s3c_gpio_setcfg_s3c24xx,
+		.get_config	= s3c_gpio_getcfg_s3c24xx,
 	}, {
 		.cfg_eint	= 2,
 		.set_config	= s3c_gpio_setcfg_s3c24xx,
+		.get_config	= s3c_gpio_getcfg_s3c24xx,
 	}, {
 		.cfg_eint	= 3,
 		.set_config	= s3c_gpio_setcfg_s3c24xx,
+		.get_config	= s3c_gpio_getcfg_s3c24xx,
 	},
 };
 
@@ -279,6 +282,8 @@ void __init s5p6440_gpiolib_set_cfg(struct s3c_gpio_cfg *chipcfg, int nr_chips)
 	for (; nr_chips > 0; nr_chips--, chipcfg++) {
 		if (!chipcfg->set_config)
 			chipcfg->set_config	= s3c_gpio_setcfg_s3c64xx_4bit;
+		if (!chipcfg->get_config)
+			chipcfg->get_config	= s3c_gpio_getcfg_s3c64xx_4bit;
 		if (!chipcfg->set_pull)
 			chipcfg->set_pull	= s3c_gpio_setpull_updown;
 		if (!chipcfg->get_pull)
arch/arm/plat-s3c24xx/gpiolib.c +2 -0
index e8c0e8a..4c0896f 100644
@@ -81,10 +81,12 @@ static int s3c24xx_gpiolib_bankg_toirq(struct gpio_chip *chip, unsigned offset)
 
 static struct s3c_gpio_cfg s3c24xx_gpiocfg_banka = {
 	.set_config	= s3c_gpio_setcfg_s3c24xx_a,
+	.get_config	= s3c_gpio_getcfg_s3c24xx_a,
 };
 
 struct s3c_gpio_cfg s3c24xx_gpiocfg_default = {
 	.set_config	= s3c_gpio_setcfg_s3c24xx,
+	.get_config	= s3c_gpio_getcfg_s3c24xx,
 };
 
 struct s3c_gpio_chip s3c24xx_gpios[] = {
arch/arm/plat-samsung/gpio-config.c +46 -1

71 lines not on this page · raw message

arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h +41 -0

59 lines not on this page · raw message

Signature · 1 line
1.7.0.4
author
#18 lore raw

PATCH 18/23 ARM: S3C24XX: Remove s3c2410_gpio_getcfg(), implement s3c_gpio_getcfg()

In reply to Ben Dooks

Add s3c_gpio_getcfg() and change anything using s3c2410_gpio_getcfg() to use this instead.

---
 arch/arm/plat-s3c24xx/gpio.c                       |   19 -------------------
 arch/arm/plat-s3c24xx/pm.c                         |    4 ++--
 arch/arm/plat-samsung/gpio-config.c                |   20 ++++++++++++++++++++
 .../plat-samsung/include/plat/gpio-cfg-helpers.h   |    6 ++++++
 arch/arm/plat-samsung/include/plat/gpio-cfg.h      |   11 +++++++++++
 5 files changed, 39 insertions(+), 21 deletions(-)
arch/arm/plat-s3c24xx/gpio.c +0 -19
index 24c0047..c7c0cd7 100644
@@ -33,25 +33,6 @@
 
 #include <mach/regs-gpio.h>
 
-unsigned int s3c2410_gpio_getcfg(unsigned int pin)
-{
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long val = __raw_readl(base);
-
-	if (pin < S3C2410_GPIO_BANKB) {
-		val >>= S3C2410_GPIO_OFFSET(pin);
-		val &= 1;
-		val += 1;
-	} else {
-		val >>= S3C2410_GPIO_OFFSET(pin)*2;
-		val &= 3;
-	}
-
-	return val | S3C2410_GPIO_INPUT;
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_getcfg);
-
 void s3c2410_gpio_pullup(unsigned int pin, unsigned int to)
 {
 	void __iomem *base = S3C24XX_GPIO_BASE(pin);
arch/arm/plat-s3c24xx/pm.c +2 -2
index 691fecc..60627e6 100644
@@ -98,11 +98,11 @@ static void s3c_pm_check_resume_pin(unsigned int pin, unsigned int irqoffs)
 	else
 		irqstate = s3c_irqwake_eintmask & (1L<<irqoffs);
 
-	pinstate = s3c2410_gpio_getcfg(pin);
+	pinstate = s3c_gpio_getcfg(pin);
 
 	if (!irqstate) {
 		if (pinstate == S3C2410_GPIO_IRQ)
-			S3C_PMDBG("Leaving IRQ %d (pin %d) enabled\n", irq, pin);
+			S3C_PMDBG("Leaving IRQ %d (pin %d) as is\n", irq, pin);
 	} else {
 		if (pinstate == S3C2410_GPIO_IRQ) {
 			S3C_PMDBG("Disabling IRQ %d (pin %d)\n", irq, pin);
arch/arm/plat-samsung/gpio-config.c +20 -0
index 19ab89d..3282db3 100644
@@ -41,6 +41,26 @@ int s3c_gpio_cfgpin(unsigned int pin, unsigned int config)
 }
 EXPORT_SYMBOL(s3c_gpio_cfgpin);
 
+unsigned s3c_gpio_getcfg(unsigned int pin)
+{
+	struct s3c_gpio_chip *chip = s3c_gpiolib_getchip(pin);
+	unsigned long flags;
+	unsigned ret = 0;
+	int offset;
+
+	if (chip) {
+		offset = pin - chip->chip.base;
+
+		local_irq_save(flags);
+		ret = s3c_gpio_do_getcfg(chip, offset);
+		local_irq_restore(flags);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL(s3c_gpio_getcfg);
+
+
 int s3c_gpio_setpull(unsigned int pin, s3c_gpio_pull_t pull)
 {
 	struct s3c_gpio_chip *chip = s3c_gpiolib_getchip(pin);
arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h +6 -0
index a8868c4..3e21c75 100644
@@ -30,6 +30,12 @@ static inline int s3c_gpio_do_setcfg(struct s3c_gpio_chip *chip,
 	return (chip->config->set_config)(chip, off, config);
 }
 
+static inline unsigned s3c_gpio_do_getcfg(struct s3c_gpio_chip *chip,
+					  unsigned int off)
+{
+	return (chip->config->get_config)(chip, off);
+}
+
 static inline int s3c_gpio_do_setpull(struct s3c_gpio_chip *chip,
 				      unsigned int off, s3c_gpio_pull_t pull)
 {
arch/arm/plat-samsung/include/plat/gpio-cfg.h +11 -0
index 29cd6a8..8d01e85 100644
@@ -77,6 +77,17 @@ struct s3c_gpio_cfg {
  */
 extern int s3c_gpio_cfgpin(unsigned int pin, unsigned int to);
 
+/**
+ * s3c_gpio_getcfg - Read the current function for a GPIO pin
+ * @pin: The pin to read the configuration value for.
+ *
+ * Read the configuration state of the given @pin, returning a value that
+ * could be passed back to s3c_gpio_cfgpin().
+ *
+ * @sa s3c_gpio_cfgpin
+ */
+extern unsigned s3c_gpio_getcfg(unsigned int pin);
+
 /* Define values for the pull-{up,down} available for each gpio pin.
  *
  * These values control the state of the weak pull-{up,down} resistors
Signature · 1 line
1.7.0.4
author
#19 lore raw

PATCH 19/23 ARM: mini2440: Move to using gpiolib API and s3c_gpio functions

In reply to Ben Dooks

Move the mach-mini2440 to using the gpiolib API for GPIOS it directly uses, and s3c_gpio calls for configuration.

---
 arch/arm/mach-s3c2440/mach-mini2440.c |   18 +++++++++---------
 1 files changed, 9 insertions(+), 9 deletions(-)
arch/arm/mach-s3c2440/mach-mini2440.c +9 -9
index 362a2f9..a76bcda 100644
@@ -103,10 +103,10 @@ static void mini2440_udc_pullup(enum s3c2410_udc_cmd_e cmd)
 
 	switch (cmd) {
 		case S3C2410_UDC_P_ENABLE :
-			s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
+			gpio_set_value(S3C2410_GPC(5), 1);
 			break;
 		case S3C2410_UDC_P_DISABLE :
-			s3c2410_gpio_setpin(S3C2410_GPC(5), 0);
+			gpio_set_value(S3C2410_GPC(5), 0);
 			break;
 		case S3C2410_UDC_P_RESET :
 			break;
@@ -636,22 +636,22 @@ static void __init mini2440_init(void)
 	s3c_gpio_cfgpin(S3C2410_GPC(0), S3C2410_GPC0_LEND);
 
 	/* Turn the backlight early on */
-	s3c2410_gpio_setpin(S3C2410_GPG(4), 1);
-	s3c_gpio_cfgpin(S3C2410_GPG(4), S3C2410_GPIO_OUTPUT);
+	WARN_ON(gpio_request(S3C2410_GPG(4), "backlight"));
+	gpio_direction_output(S3C2410_GPG(4), 1);
 
 	/* remove pullup on optional PWM backlight -- unused on 3.5 and 7"s */
-	s3c2410_gpio_pullup(S3C2410_GPB(1), 0);
+	s3c_gpio_setpull(S3C2410_GPB(1), S3C_GPIO_PULL_UP);
 	s3c2410_gpio_setpin(S3C2410_GPB(1), 0);
 	s3c_gpio_cfgpin(S3C2410_GPB(1), S3C2410_GPIO_INPUT);
 
 	/* Make sure the D+ pullup pin is output */
-	s3c_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
+	WARN_ON(gpio_request(S3C2410_GPC(5), "udc pup"));
+	gpio_direction_output(S3C2410_GPC(5), 0);
 
 	/* mark the key as input, without pullups (there is one on the board) */
 	for (i = 0; i < ARRAY_SIZE(mini2440_buttons); i++) {
-		s3c2410_gpio_pullup(mini2440_buttons[i].gpio, 0);
-		s3c_gpio_cfgpin(mini2440_buttons[i].gpio,
-					S3C2410_GPIO_INPUT);
+		s3c_gpio_setpull(mini2440_buttons[i].gpio, S3C_GPIO_PULL_UP);
+		s3c_gpio_cfgpin(mini2440_buttons[i].gpio, S3C2410_GPIO_INPUT);
 	}
 	if (features.lcd_index != -1) {
 		int li;
Signature · 1 line
1.7.0.4
author
#20 lore raw

PATCH 20/23 ARM: S3C2410: Remove the users of s3c2410_gpio_pullup()

In reply to Ben Dooks

Remove the last s3c2410_gpio_pullup() users in arch/arm/mach-s3c2410

Note, since mach-h1940.c is setting output and a pull-up, the call has vbeen chanerd to S3C_GPIO_PULL_NONE instead of S3C_GPIO_PULL_UP.

---
 arch/arm/mach-s3c2410/mach-amlm5900.c |    2 +-
 arch/arm/mach-s3c2410/mach-h1940.c    |    2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
arch/arm/mach-s3c2410/mach-amlm5900.c +1 -1
index b42a760..34fc05a 100644
@@ -227,7 +227,7 @@ static void amlm5900_init_pm(void)
 		enable_irq_wake(IRQ_EINT9);
 		/* configure the suspend/resume status pin */
 		s3c_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT);
-		s3c2410_gpio_pullup(S3C2410_GPF(2), 0);
+		s3c_gpio_setpull(S3C2410_GPF(2), S3C_GPIO_PULL_UP);
 	}
 }
 static void __init amlm5900_init(void)
arch/arm/mach-s3c2410/mach-h1940.c +1 -1
index e2f7e64..9531b4c 100644
@@ -209,7 +209,7 @@ static int h1940_backlight_init(struct device *dev)
 	gpio_request(S3C2410_GPB(0), "Backlight");
 
 	gpio_direction_output(S3C2410_GPB(0), 0);
-	s3c2410_gpio_pullup(S3C2410_GPB(0), 0);
+	s3c_gpio_setpull(S3C2410_GPB(0), S3C_GPIO_PULL_NONE);
 	s3c_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPB0_TOUT0);
 
 	return 0;
Signature · 1 line
1.7.0.4
author
#21 lore raw

PATCH 21/23 ARM: S3C24XX: Wrapper s3c2410_gpio_setpin and s3c2410_gpio_pullup()

In reply to Ben Dooks

Change s3c2410_gpio_setpin() and s3c2410_gpio_pullup() to use the new s3c_ gpio configuration calls until all their users are converted.

---
 arch/arm/plat-s3c24xx/gpio.c |   47 +++++++++++++++++-------------------------
 1 files changed, 19 insertions(+), 28 deletions(-)
arch/arm/plat-s3c24xx/gpio.c +19 -28
index c7c0cd7..45126d3 100644
@@ -1,6 +1,6 @@
 /* linux/arch/arm/plat-s3c24xx/gpio.c
  *
- * Copyright (c) 2004-2005 Simtec Electronics
+ * Copyright (c) 2004-2010 Simtec Electronics
  *	Ben Dooks <[email protected]>
  *
  * S3C24XX GPIO support
@@ -25,6 +25,7 @@
 #include <linux/module.h>
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
+#include <linux/gpio.h>
 #include <linux/io.h>
 
 #include <mach/hardware.h>
@@ -33,44 +34,34 @@
 
 #include <mach/regs-gpio.h>
 
+/* gpiolib wrappers until these are totally eliminated */
+
 void s3c2410_gpio_pullup(unsigned int pin, unsigned int to)
 {
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
-	unsigned long flags;
-	unsigned long up;
+	int ret;
 
-	if (pin < S3C2410_GPIO_BANKB)
-		return;
+	WARN_ON(to);	/* should be none of these left */
 
-	local_irq_save(flags);
-
-	up = __raw_readl(base + 0x08);
-	up &= ~(1L << offs);
-	up |= to << offs;
-	__raw_writel(up, base + 0x08);
+	if (!to) {
+		/* if pull is enabled, try first with up, and if that
+		 * fails, try using down */
 
-	local_irq_restore(flags);
+		ret = s3c_gpio_setpull(pin, S3C_GPIO_PULL_UP);
+		if (ret)
+			s3c_gpio_setpull(pin, S3C_GPIO_PULL_DOWN);
+	} else {
+		s3c_gpio_setpull(pin, S3C_GPIO_PULL_NONE);
+	}
 }
-
 EXPORT_SYMBOL(s3c2410_gpio_pullup);
 
-
 void s3c2410_gpio_setpin(unsigned int pin, unsigned int to)
 {
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
-	unsigned long flags;
-	unsigned long dat;
+	/* do this via gpiolib until all users removed */
 
-	local_irq_save(flags);
-
-	dat = __raw_readl(base + 0x04);
-	dat &= ~(1 << offs);
-	dat |= to << offs;
-	__raw_writel(dat, base + 0x04);
-
-	local_irq_restore(flags);
+	gpio_request(pin, "temporary");
+	gpio_set_value(pin, to);
+	gpio_free(pin);
 }
 
 EXPORT_SYMBOL(s3c2410_gpio_setpin);
Signature · 1 line
1.7.0.4
author
#22 lore raw

PATCH 22/23 ARM: S3C24XX: Remove S3C2410_GPJ numbering

In reply to Ben Dooks

Remove the old S3C2410_GPJ as we will be moving to the new gpiolib based driver code and these numbers will become invalid.

---
 arch/arm/mach-s3c2410/include/mach/regs-gpioj.h |   19 -------------------
 1 files changed, 0 insertions(+), 19 deletions(-)
arch/arm/mach-s3c2410/include/mach/regs-gpioj.h +0 -19
index de463bc..5025757 100644
@@ -22,81 +22,62 @@
  * pull up works like all other ports.
 */
 
-#define S3C2440_GPIO_BANKJ  (416)
-
 #define S3C2413_GPJCON		S3C2410_GPIOREG(0x80)
 #define S3C2413_GPJDAT		S3C2410_GPIOREG(0x84)
 #define S3C2413_GPJUP		S3C2410_GPIOREG(0x88)
 #define S3C2413_GPJSLPCON	S3C2410_GPIOREG(0x8C)
 
-#define S3C2440_GPJ0            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 0)
 #define S3C2440_GPJ0_INP        (0x00 << 0)
 #define S3C2440_GPJ0_OUTP       (0x01 << 0)
 #define S3C2440_GPJ0_CAMDATA0   (0x02 << 0)
 
-#define S3C2440_GPJ1            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 1)
 #define S3C2440_GPJ1_INP        (0x00 << 2)
 #define S3C2440_GPJ1_OUTP       (0x01 << 2)
 #define S3C2440_GPJ1_CAMDATA1   (0x02 << 2)
 
-#define S3C2440_GPJ2            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 2)
 #define S3C2440_GPJ2_INP        (0x00 << 4)
 #define S3C2440_GPJ2_OUTP       (0x01 << 4)
 #define S3C2440_GPJ2_CAMDATA2   (0x02 << 4)
 
-#define S3C2440_GPJ3            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 3)
 #define S3C2440_GPJ3_INP        (0x00 << 6)
 #define S3C2440_GPJ3_OUTP       (0x01 << 6)
 #define S3C2440_GPJ3_CAMDATA3   (0x02 << 6)
 
-#define S3C2440_GPJ4            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 4)
 #define S3C2440_GPJ4_INP        (0x00 << 8)
 #define S3C2440_GPJ4_OUTP       (0x01 << 8)
 #define S3C2440_GPJ4_CAMDATA4   (0x02 << 8)
 
-#define S3C2440_GPJ5            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 5)
 #define S3C2440_GPJ5_INP        (0x00 << 10)
 #define S3C2440_GPJ5_OUTP       (0x01 << 10)
 #define S3C2440_GPJ5_CAMDATA5   (0x02 << 10)
 
-#define S3C2440_GPJ6            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 6)
 #define S3C2440_GPJ6_INP        (0x00 << 12)
 #define S3C2440_GPJ6_OUTP       (0x01 << 12)
 #define S3C2440_GPJ6_CAMDATA6   (0x02 << 12)
 
-#define S3C2440_GPJ7            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 7)
 #define S3C2440_GPJ7_INP        (0x00 << 14)
 #define S3C2440_GPJ7_OUTP       (0x01 << 14)
 #define S3C2440_GPJ7_CAMDATA7   (0x02 << 14)
 
-#define S3C2440_GPJ8            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 8)
 #define S3C2440_GPJ8_INP        (0x00 << 16)
 #define S3C2440_GPJ8_OUTP       (0x01 << 16)
 #define S3C2440_GPJ8_CAMPCLK    (0x02 << 16)
 
-#define S3C2440_GPJ9            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 9)
 #define S3C2440_GPJ9_INP        (0x00 << 18)
 #define S3C2440_GPJ9_OUTP       (0x01 << 18)
 #define S3C2440_GPJ9_CAMVSYNC   (0x02 << 18)
 
-#define S3C2440_GPJ10           S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 10)
 #define S3C2440_GPJ10_INP       (0x00 << 20)
 #define S3C2440_GPJ10_OUTP      (0x01 << 20)
 #define S3C2440_GPJ10_CAMHREF   (0x02 << 20)
 
-#define S3C2440_GPJ11           S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 11)
 #define S3C2440_GPJ11_INP       (0x00 << 22)
 #define S3C2440_GPJ11_OUTP      (0x01 << 22)
 #define S3C2440_GPJ11_CAMCLKOUT (0x02 << 22)
 
-#define S3C2440_GPJ12           S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 12)
 #define S3C2440_GPJ12_INP       (0x00 << 24)
 #define S3C2440_GPJ12_OUTP      (0x01 << 24)
 #define S3C2440_GPJ12_CAMRESET  (0x02 << 24)
 
-#define S3C2443_GPJ13		S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 13)
-#define S3C2443_GPJ14		S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 14)
-#define S3C2443_GPJ15		S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 15)
-
 #endif	/* __ASM_ARCH_REGS_GPIOJ_H */
 
Signature · 1 line
1.7.0.4
author
#23 lore raw

PATCH 23/23 ARM: S3C24XX: Remove _INP macros in <mach/regs-gpioj.h>

In reply to Ben Dooks

Remove the _INP definitions, they are all zero and also unused

---
 arch/arm/mach-s3c2410/include/mach/regs-gpioj.h |   13 -------------
 1 files changed, 0 insertions(+), 13 deletions(-)
arch/arm/mach-s3c2410/include/mach/regs-gpioj.h +0 -13
index 5025757..19575e0 100644
@@ -27,55 +27,42 @@
 #define S3C2413_GPJUP		S3C2410_GPIOREG(0x88)
 #define S3C2413_GPJSLPCON	S3C2410_GPIOREG(0x8C)
 
-#define S3C2440_GPJ0_INP        (0x00 << 0)
 #define S3C2440_GPJ0_OUTP       (0x01 << 0)
 #define S3C2440_GPJ0_CAMDATA0   (0x02 << 0)
 
-#define S3C2440_GPJ1_INP        (0x00 << 2)
 #define S3C2440_GPJ1_OUTP       (0x01 << 2)
 #define S3C2440_GPJ1_CAMDATA1   (0x02 << 2)
 
-#define S3C2440_GPJ2_INP        (0x00 << 4)
 #define S3C2440_GPJ2_OUTP       (0x01 << 4)
 #define S3C2440_GPJ2_CAMDATA2   (0x02 << 4)
 
-#define S3C2440_GPJ3_INP        (0x00 << 6)
 #define S3C2440_GPJ3_OUTP       (0x01 << 6)
 #define S3C2440_GPJ3_CAMDATA3   (0x02 << 6)
 
-#define S3C2440_GPJ4_INP        (0x00 << 8)
 #define S3C2440_GPJ4_OUTP       (0x01 << 8)
 #define S3C2440_GPJ4_CAMDATA4   (0x02 << 8)
 
-#define S3C2440_GPJ5_INP        (0x00 << 10)
 #define S3C2440_GPJ5_OUTP       (0x01 << 10)
 #define S3C2440_GPJ5_CAMDATA5   (0x02 << 10)
 
-#define S3C2440_GPJ6_INP        (0x00 << 12)
 #define S3C2440_GPJ6_OUTP       (0x01 << 12)
 #define S3C2440_GPJ6_CAMDATA6   (0x02 << 12)
 
-#define S3C2440_GPJ7_INP        (0x00 << 14)
 #define S3C2440_GPJ7_OUTP       (0x01 << 14)
 #define S3C2440_GPJ7_CAMDATA7   (0x02 << 14)
 
-#define S3C2440_GPJ8_INP        (0x00 << 16)
 #define S3C2440_GPJ8_OUTP       (0x01 << 16)
 #define S3C2440_GPJ8_CAMPCLK    (0x02 << 16)
 
-#define S3C2440_GPJ9_INP        (0x00 << 18)
 #define S3C2440_GPJ9_OUTP       (0x01 << 18)
 #define S3C2440_GPJ9_CAMVSYNC   (0x02 << 18)
 
-#define S3C2440_GPJ10_INP       (0x00 << 20)
 #define S3C2440_GPJ10_OUTP      (0x01 << 20)
 #define S3C2440_GPJ10_CAMHREF   (0x02 << 20)
 
-#define S3C2440_GPJ11_INP       (0x00 << 22)
 #define S3C2440_GPJ11_OUTP      (0x01 << 22)
 #define S3C2440_GPJ11_CAMCLKOUT (0x02 << 22)
 
-#define S3C2440_GPJ12_INP       (0x00 << 24)
 #define S3C2440_GPJ12_OUTP      (0x01 << 24)
 #define S3C2440_GPJ12_CAMRESET  (0x02 << 24)
 
Signature · 1 line
1.7.0.4