Add support for the IGEP v2 board.
v3 cover Add support for the IGEP v2 board.
Hello,
This is the version 3 of patch series to add initial support for OMAP3 IGEP v2 board.
CHANGES:
* since v2
- [1/3] keep lists sorted
- [2/3] fix multiline comment style
- [3/3] add entry to MAINTAINERS
* since v1
- [2/3] fix parens in NUMONYX_V_ACTIMB_165 define
- [3/3] add extra space after first &ctrl_base in file igep0020.c
- [3/3] add a space after the 57600 comma in file igep0020.h
- [3/3] remove CONFIG_SYS_ARM_WITHOUT_RELOC undef
$ git diff --stat origin/master MAINTAINERS | 4 + MAKEALL | 1 + arch/arm/include/asm/arch-omap3/mem.h | 43 ++++++ board/isee/igep0020/Makefile | 49 +++++++ board/isee/igep0020/config.mk | 33 +++++ board/isee/igep0020/igep0020.c | 128 ++++++++++++++++++ board/isee/igep0020/igep0020.h | 156 ++++++++++++++++++++++ boards.cfg | 1 + drivers/mtd/onenand/onenand_base.c | 1 + include/configs/igep0020.h | 228 +++++++++++++++++++++++++++++++++ include/linux/mtd/onenand.h | 1 + 11 files changed, 645 insertions(+), 0 deletions(-)
PATCH v3 1/3 mtd: OneNAND: add support for OneNAND manufactured by Numonyx
This patch adds the Numonyx manufacturer code (0x20) to onenand manufacturers.
--- drivers/mtd/onenand/onenand_base.c | 1 + include/linux/mtd/onenand.h | 1 + 2 files changed, 2 insertions(+), 0 deletions(-)
drivers/mtd/onenand/onenand_base.c +1 -0
@@ -2213,6 +2213,7 @@ char *onenand_print_device_info(int device, int version) }static const struct onenand_manufacturers onenand_manuf_ids[] = { + {ONENAND_MFR_NUMONYX ,"Numonyx" }, {ONENAND_MFR_SAMSUNG ,"Samsung" }, };
include/linux/mtd/onenand.h +1 -0
@@ -154,6 +154,7 @@ struct onenand_chip {/* * OneNAND Flash Manufacturer ID Codes */ +#define ONENAND_MFR_NUMONYX 0x20#define ONENAND_MFR_SAMSUNG 0xec/**
Signature · 1 line
1.7.0.4
PATCH v3 1/3 mtd: OneNAND: add support for OneNAND manufactured by Numonyx
Quoted 41 lines · Enric Balletbo i Serra
This patch adds the Numonyx manufacturer code (
0x20) to onenand manufacturers.Signed-off-by Enric Balletbo i Serra <[email protected]>---
?drivers/mtd/onenand/onenand_base.c | ? ?1 +
?include/linux/mtd/onenand.h ? ? ? ?| ? ?1 +
?2 files changed, 2 insertions(+), 0 deletions(-)drivers/mtd/onenand/onenand_base.c +1
-0@@ -2213,6 +2213,7 @@ char *onenand_print_device_info(int device, int version) ?} ?static const struct onenand_manufacturers onenand_manuf_ids[] = { + ? ? ? {ONENAND_MFR_NUMONYX, "Numonyx"}, ? ? ? ?{ONENAND_MFR_SAMSUNG, "Samsung"}, ?};include/linux/mtd/onenand.h +0
-0@@ -154,6 +154,7 @@ struct onenand_chip {?/*
?* OneNAND Flash Manufacturer ID Codes
?*/
+#defineONENAND_MFR_NUMONYX? ?0x20
?#defineONENAND_MFR_SAMSUNG? ?0xec?/**
--
1.7.0.4_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
PATCH v3 1/3 mtd: OneNAND: add support for OneNAND manufactured by Numonyx
In reply to Enric Balletbo i SerraQuoted 26 lines · Enric Balletbo i Serra
This patch adds the Numonyx manufacturer code (
0x20) to onenand manufacturers.Signed-off-by Enric Balletbo i Serra <[email protected]>--- drivers/mtd/onenand/onenand_base.c | 1 + include/linux/mtd/onenand.h | 1 + 2 files changed, 2 insertions(+), 0 deletions(-)drivers/mtd/onenand/onenand_base.c +1
-0@@ -2213,6 +2213,7 @@ char *onenand_print_device_info(int device, int version) }static const struct onenand_manufacturers onenand_manuf_ids[] = { + {ONENAND_MFR_NUMONYX ,"Numonyx" }, {ONENAND_MFR_SAMSUNG ,"Samsung" }, };include/linux/mtd/onenand.h +0
-0
include/linux/mtd/onenand.h struct onenand_chip { · line 160
Quoted 7 lines
include/linux/mtd/onenand.h +1
-0@@ -154,6 +154,7 @@ struct onenand_chip {/* * OneNAND Flash Manufacturer ID Codes */ +#define ONENAND_MFR_NUMONYX 0x20#define ONENAND_MFR_SAMSUNG 0xec/**
PATCH v3 2/3 OMAP3: SDRC: Introduce Numonyx DDR type
In reply to Enric Balletbo i SerraIntroduce Numonyx DDR timings and provide CONFIG_OMAP3_NUMONYX_DDR config options to allow for platform files to setup their timings.
--- arch/arm/include/asm/arch-omap3/mem.h | 43 +++++++++++++++++++++++++++++++++ 1 files changed, 43 insertions(+), 0 deletions(-)
arch/arm/include/asm/arch-omap3/mem.h +43 -0
@@ -128,6 +128,45 @@ enum { (MICRON_XSR_165 << 0) | (MICRON_TXP_165 << 8) | \ (MICRON_TWTR_165 << 16)) +/* +* NUMONYX part of IGEP v2 (165MHz optimized) 6.06ns +* ACTIMA +* TDAL = Twr/Tck + Trp/tck = 15/6 + 18/6 = 2.5 + 3 = 5.5 -> 6 +* TDPL (Twr) = 15/6 = 2.5 -> 3 +* TRRD = 12/6 = 2 +* TRCD = 22.5/6 = 3.75 -> 4 +* TRP = 18/6 = 3 +* TRAS = 42/6 = 7 +* TRC = 60/6 = 10 +* TRFC = 140/6 = 23.3 -> 24 +* ACTIMB +* TWTR = 2 +* TCKE = 2 +* TXSR = 200/6 = 33.3 -> 34 +* TXP = 1.0 + 1.1 = 2.1 -> 3 +*/ +#define NUMONYX_TDAL_165 6 +#define NUMONYX_TDPL_165 3 +#define NUMONYX_TRRD_165 2 +#define NUMONYX_TRCD_165 4 +#define NUMONYX_TRP_165 3 +#define NUMONYX_TRAS_165 7 +#define NUMONYX_TRC_165 10 +#define NUMONYX_TRFC_165 24 +#define NUMONYX_V_ACTIMA_165 ((NUMONYX_TRFC_165 << 27) | \ + (NUMONYX_TRC_165 << 22) | (NUMONYX_TRAS_165 << 18) | \ + (NUMONYX_TRP_165 << 15) | (NUMONYX_TRCD_165 << 12) | \ + (NUMONYX_TRRD_165 << 9) | (NUMONYX_TDPL_165 << 6) | \ + (NUMONYX_TDAL_165)) + +#define NUMONYX_TWTR_165 2 +#define NUMONYX_TCKE_165 2 +#define NUMONYX_TXP_165 3 +#define NUMONYX_XSR_165 34 +#define NUMONYX_V_ACTIMB_165 ((NUMONYX_TCKE_165 << 12) | \ + (NUMONYX_XSR_165 << 0) | (NUMONYX_TXP_165 << 8) | \ + (NUMONYX_TWTR_165 << 16)) +#ifdef CONFIG_OMAP3_INFINEON_DDR #define V_ACTIMA_165 INFINEON_V_ACTIMA_165#define V_ACTIMB_165 INFINEON_V_ACTIMB_165
@@ -136,6 +175,10 @@ enum {#define V_ACTIMA_165 MICRON_V_ACTIMA_165#define V_ACTIMB_165 MICRON_V_ACTIMB_165#endif +#ifdef CONFIG_OMAP3_NUMONYX_DDR +#define V_ACTIMA_165 NUMONYX_V_ACTIMA_165 +#define V_ACTIMB_165 NUMONYX_V_ACTIMB_165 +#endif #if !defined(V_ACTIMA_165 ) || !defined(V_ACTIMB_165 )#error "Please choose the right DDR type in config header"
Signature · 1 line
1.7.0.4
PATCH v3 2/3 OMAP3: SDRC: Introduce Numonyx DDR type
Quoted 59 lines · Enric Balletbo i Serra
Introduce Numonyx DDR timings and provide
CONFIG_OMAP3_NUMONYX_DDRconfig options to allow for platform files to setup their timings.Signed-off-by Enric Balletbo i Serra <[email protected]>--- arch/arm/include/asm/arch-omap3/mem.h | 43 +++++++++++++++++++++++++++++++++ 1 files changed, 43 insertions(+), 0 deletions(-)arch/arm/include/asm/arch-omap3/mem.h +39
-0@@ -128,6 +128,45 @@ enum { (MICRON_XSR_165 << 0) | (MICRON_TXP_165 << 8) | \ (MICRON_TWTR_165 << 16)) +/* +* NUMONYX part of IGEP v2 (165MHz optimized) 6.06ns +* ACTIMA +* TDAL = Twr/Tck + Trp/tck = 15/6 + 18/6 = 2.5 + 3 = 5.5 -> 6 +* TDPL (Twr) = 15/6 = 2.5 -> 3 +* TRRD = 12/6 = 2 +* TRCD = 22.5/6 = 3.75 -> 4 +* TRP = 18/6 = 3 +* TRAS = 42/6 = 7 +* TRC = 60/6 = 10 +* TRFC = 140/6 = 23.3 -> 24 +* ACTIMB +* TWTR = 2 +* TCKE = 2 +* TXSR = 200/6 = 33.3 -> 34 +* TXP = 1.0 + 1.1 = 2.1 -> 3 +*/ +#define NUMONYX_TDAL_165 6 +#define NUMONYX_TDPL_165 3 +#define NUMONYX_TRRD_165 2 +#define NUMONYX_TRCD_165 4 +#define NUMONYX_TRP_165 3 +#define NUMONYX_TRAS_165 7 +#define NUMONYX_TRC_165 10 +#define NUMONYX_TRFC_165 24 +#define NUMONYX_V_ACTIMA_165 ((NUMONYX_TRFC_165 << 27) | \ + (NUMONYX_TRC_165 << 22) | (NUMONYX_TRAS_165 << 18) | \ + (NUMONYX_TRP_165 << 15) | (NUMONYX_TRCD_165 << 12) | \ + (NUMONYX_TRRD_165 << 9) | (NUMONYX_TDPL_165 << 6) | \ + (NUMONYX_TDAL_165)) + +#define NUMONYX_TWTR_165 2 +#define NUMONYX_TCKE_165 2 +#define NUMONYX_TXP_165 3 +#define NUMONYX_XSR_165 34 +#define NUMONYX_V_ACTIMB_165 ((NUMONYX_TCKE_165 << 12) | \ + (NUMONYX_XSR_165 << 0) | (NUMONYX_TXP_165 << 8) | \ + (NUMONYX_TWTR_165 << 16)) +#ifdef CONFIG_OMAP3_INFINEON_DDR #define V_ACTIMA_165 INFINEON_V_ACTIMA_165#define V_ACTIMB_165 INFINEON_V_ACTIMB_165
arch/arm/include/asm/arch-omap3/mem.h enum { · line 184
Quoted 10 lines
arch/arm/include/asm/arch-omap3/mem.h +4
-0@@ -136,6 +175,10 @@ enum {#define V_ACTIMA_165 MICRON_V_ACTIMA_165#define V_ACTIMB_165 MICRON_V_ACTIMB_165#endif +#ifdef CONFIG_OMAP3_NUMONYX_DDR +#define V_ACTIMA_165 NUMONYX_V_ACTIMA_165 +#define V_ACTIMB_165 NUMONYX_V_ACTIMB_165 +#endif #if !defined(V_ACTIMA_165 ) || !defined(V_ACTIMB_165 )#error "Please choose the right DDR type in config header"
PATCH v3 3/3 OMAP3: Add support for the IGEP v2 board.
In reply to Enric Balletbo i SerraThe IGEP v2 board is a low-cost, fan-less and industrial temperature range single board computer that unleashes laptop-like performance and expandability without the bulk, expense, or noise of typical desktop machines. Its architecture shares much in common with other OMAP3 boards.
--- MAINTAINERS | 4 + MAKEALL | 1 + board/isee/igep0020/Makefile | 49 +++++++++ board/isee/igep0020/config.mk | 33 ++++++ board/isee/igep0020/igep0020.c | 128 ++++++++++++++++++++++ board/isee/igep0020/igep0020.h | 156 +++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/igep0020.h | 228 ++++++++++++++++++++++++++++++++++++++++ 8 files changed, 600 insertions(+), 0 deletions(-) create mode 100644 board/isee/igep0020/Makefile create mode 100644 board/isee/igep0020/config.mk create mode 100644 board/isee/igep0020/igep0020.c create mode 100644 board/isee/igep0020/igep0020.h create mode 100644 include/configs/igep0020.h
MAINTAINERS +4 -0
@@ -818,6 +818,10 @@ Alex Z lart SA1100 dnp1110 SA1110 +Enric Balletbo i Serra <[email protected]> + + igep0020 ARM ARMV7 (OMAP3xx SoC) + ------------------------------------------------------------------------- Unknown / orphaned boards:
MAKEALL +1 -0
@@ -490,6 +490,7 @@ LIST_ARM11=" \ LIST_ARMV7=" \ am3517_evm \ devkit8000 \ + igep0020 \ mx51evk \ omap3_beagle \ omap3_overo \
board/isee/igep0020/Makefile new file +49 -0
49 lines not on this page · raw message
board/isee/igep0020/config.mk new file +33 -0
@@ -0,0 +1,33 @@ +# +# (C) Copyright 2009 +# ISEE 2007 SL, <www.iseebcn.com> +# +# IGEP0020 uses OMAP3 (ARM-CortexA8) cpu +# see http://www.ti.com/ for more information on Texas Instruments +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +# Physical Address: +# 8000'0000 (bank0) +# A000/0000 (bank1) +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 +# (mem base + reserved) + +# For use with external or internal boots. +TEXT_BASE = 0x80008000
board/isee/igep0020/igep0020.c new file +128 -0
128 lines not on this page · raw message
board/isee/igep0020/igep0020.h new file +156 -0
156 lines not on this page · raw message
boards.cfg +1 -0
@@ -262,6 +262,7 @@ omap4_panda arm armv7 panda ti omap4 omap4_sdp4430 arm armv7 sdp4430 ti omap4 am3517_evm arm armv7 am3517evm logicpd omap3 devkit8000 arm armv7 devkit8000 timll omap3 +igep0020 arm armv7 igep0020 isee omap3 s5p_goni arm armv7 goni samsung s5pc1xx smdkc100 arm armv7 smdkc100 samsung s5pc1xx ixdpg425 arm ixp
include/configs/igep0020.h new file +228 -0
228 lines not on this page · raw message
Signature · 1 line
1.7.0.4
PATCH v3 3/3 OMAP3: Add support for the IGEP v2 board.
Quoted 675 lines · Enric Balletbo i Serra
The IGEP v2 board is a low-cost, fan-less and industrial temperature range single board computer that unleashes laptop-like performance and expandability without the bulk, expense, or noise of typical desktop machines. Its architecture shares much in common with other OMAP3 boards.
Signed-off-by Enric Balletbo i Serra <[email protected]>--- MAINTAINERS | 4 + MAKEALL | 1 + board/isee/igep0020/Makefile | 49 +++++++++ board/isee/igep0020/config.mk | 33 ++++++ board/isee/igep0020/igep0020.c | 128 ++++++++++++++++++++++ board/isee/igep0020/igep0020.h | 156 +++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/igep0020.h | 228 ++++++++++++++++++++++++++++++++++++++++ 8 files changed, 600 insertions(+), 0 deletions(-) create mode 100644 board/isee/igep0020/Makefile create mode 100644 board/isee/igep0020/config.mk create mode 100644 board/isee/igep0020/igep0020.c create mode 100644 board/isee/igep0020/igep0020.h create mode 100644 include/configs/igep0020.hMAINTAINERS +4
-0@@ -818,6 +818,10 @@ Alex Z lart SA1100 dnp1110 SA1110 +Enric Balletbo i Serra <[email protected]> + + igep0020 ARM ARMV7 (OMAP3xx SoC) + ------------------------------------------------------------------------- Unknown / orphaned boards:MAKEALL +1
-0@@ -490,6 +490,7 @@ LIST_ARM11=" \ LIST_ARMV7=" \ am3517_evm \ devkit8000 \ + igep0020 \ mx51evk \ omap3_beagle \ omap3_overo \board/isee/igep0020/Makefile new file +49
-0@@ -0,0 +1,49 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := igep0020.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################board/isee/igep0020/config.mk new file +33
-0@@ -0,0 +1,33 @@ +# +# (C) Copyright 2009 +# ISEE 2007 SL, <www.iseebcn.com> +# +# IGEP0020 uses OMAP3 (ARM-CortexA8) cpu +# see http://www.ti.com/ for more information on Texas Instruments +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +# Physical Address: +# 8000'0000 (bank0) +# A000/0000 (bank1) +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 +# (mem base + reserved) + +# For use with external or internal boots. +TEXT_BASE = 0x80008000board/isee/igep0020/igep0020.c new file +128
-0@@ -0,0 +1,128 @@ +/* +* (C) Copyright 2010 +* ISEE 2007 SL, <www.iseebcn.com> +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ +#include <common.h> +#include <twl4030.h> +#include <asm/io.h> +#include <asm/arch/gpio.h> +#include <asm/arch/mem.h> +#include <asm/arch/mux.h> +#include <asm/arch/sys_proto.h> +#include <asm/mach-types.h> +#include "igep0020.h" + +/* GPMC definitions for LAN9221 chips */ +static const u32 gpmc_lan_config[] = { +NET_LAN9221_GPMC_CONFIG1 , +NET_LAN9221_GPMC_CONFIG2 , +NET_LAN9221_GPMC_CONFIG3 , +NET_LAN9221_GPMC_CONFIG4 , +NET_LAN9221_GPMC_CONFIG5 , +NET_LAN9221_GPMC_CONFIG6 , +}; + +/* +* Routine: board_init +* Description: Early hardware init. +*/ +int board_init (void ) +{ +DECLARE_GLOBAL_DATA_PTR ; + +gpmc_init ();/* in SRAM or SDRAM, finish GPMC */ +/* board id for Linux */ + gd->bd->bi_arch_number =MACH_TYPE_IGEP0020 ; +/* boot param addr */ + gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 +0x100 ); + +return 0 ; +} + +/* +* Routine: setup_net_chip +* Description: Setting up the configuration GPMC registers specific to the +* Ethernet hardware. +*/ +#if defined(CONFIG_CMD_NET ) +static void setup_net_chip (void ) +{ +struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE ; + +enable_gpmc_cs_config (gpmc_lan_config, &gpmc_cfg->cs[5 ],0x2C000000 , +GPMC_SIZE_16M ); + +/* Enable off mode for NWE in PADCONF_GPMC_NWE register */ +writew (readw (&ctrl_base->gpmc_nwe) |0x0E00 , &ctrl_base->gpmc_nwe); +/* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */ +writew (readw (&ctrl_base->gpmc_noe) |0x0E00 , &ctrl_base->gpmc_noe); +/* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */ +writew (readw (&ctrl_base->gpmc_nadv_ale) |0x0E00 , + &ctrl_base->gpmc_nadv_ale); + +/* Make GPIO 64 as output pin and send a magic pulse through it */ +if (!omap_request_gpio (64 )) { +omap_set_gpio_direction (64 ,0 ); +omap_set_gpio_dataout (64 ,1 ); +udelay (1 ); +omap_set_gpio_dataout (64 ,0 ); +udelay (1 ); +omap_set_gpio_dataout (64 ,1 ); + } +} +#endif + +/* +* Routine: misc_init_r +* Description: Configure board specific parts +*/ +int misc_init_r (void ) +{ +twl4030_power_init (); + +#if defined(CONFIG_CMD_NET ) +setup_net_chip (); +#endif + +dieid_num_r (); + +return 0 ; +} + +/* +* Routine: set_muxconf_regs +* Description: Setting up the configuration Mux registers specific to the +* hardware. Many pins need to be moved from protect to primary +* mode. +*/ +void set_muxconf_regs (void ) +{ +MUX_DEFAULT (); +} + +int board_eth_init (bd_t *bis) +{ +int rc =0 ; +#ifdef CONFIG_SMC911X + rc =smc911x_initialize (0 ,CONFIG_SMC911X_BASE ); +#endif +return rc; +}board/isee/igep0020/igep0020.h new file +156
-0@@ -0,0 +1,156 @@ +/* +* (C) Copyright 2010 +* ISEE 2007 SL, <www.iseebcn.com> +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ +#ifndef _IGEP0020_H_ +#define _IGEP0020_H_ + +const omap3_sysinfo sysinfo = { +DDR_STACKED , +"IGEP v2 board" , +"ONENAND" , +}; + +/* GPMC CS 5 connected to an SMSC LAN9221 ethernet controller */ +#define NET_LAN9221_GPMC_CONFIG1 0x00001000 +#define NET_LAN9221_GPMC_CONFIG2 0x00080701 +#define NET_LAN9221_GPMC_CONFIG3 0x00020201 +#define NET_LAN9221_GPMC_CONFIG4 0x08030703 +#define NET_LAN9221_GPMC_CONFIG5 0x00060908 +#define NET_LAN9221_GPMC_CONFIG6 0x87030000 +#define NET_LAN9221_GPMC_CONFIG7 0x00000f6c + +static void setup_net_chip (void ); + +/* +* IEN - Input Enable +* IDIS - Input Disable +* PTD - Pull type Down +* PTU - Pull type Up +* DIS - Pull type selection is inactive +* EN - Pull type selection is active +* M0 - Mode 0 +* The commented string gives the final mux configuration for that pin +*/ +#define MUX_DEFAULT ()\ + MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0))/* SDRC_D0 */ \ + MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /* SDRC_D1 */\ + MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /* SDRC_D2 */\ + MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /* SDRC_D3 */\ + MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /* SDRC_D4 */\ + MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /* SDRC_D5 */\ + MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /* SDRC_D6 */\ + MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /* SDRC_D7 */\ + MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /* SDRC_D8 */\ + MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /* SDRC_D9 */\ + MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /* SDRC_D10 */\ + MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /* SDRC_D11 */\ + MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /* SDRC_D12 */\ + MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /* SDRC_D13 */\ + MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /* SDRC_D14 */\ + MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /* SDRC_D15 */\ + MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /* SDRC_D16 */\ + MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /* SDRC_D17 */\ + MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /* SDRC_D18 */\ + MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /* SDRC_D19 */\ + MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /* SDRC_D20 */\ + MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /* SDRC_D21 */\ + MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /* SDRC_D22 */\ + MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /* SDRC_D23 */\ + MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /* SDRC_D24 */\ + MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /* SDRC_D25 */\ + MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /* SDRC_D26 */\ + MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /* SDRC_D27 */\ + MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /* SDRC_D28 */\ + MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /* SDRC_D29 */\ + MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /* SDRC_D30 */\ + MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /* SDRC_D31 */\ + MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /* SDRC_CLK */\ + MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /* SDRC_DQS0 */\ + MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /* SDRC_DQS1 */\ + MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /* SDRC_DQS2 */\ + MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /* SDRC_DQS3 */\ + MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0)) /* GPMC_A1 */\ + MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0)) /* GPMC_A2 */\ + MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0)) /* GPMC_A3 */\ + MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0)) /* GPMC_A4 */\ + MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0)) /* GPMC_A5 */\ + MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /* GPMC_A6 */\ + MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /* GPMC_A7 */\ + MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /* GPMC_A8 */\ + MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /* GPMC_A9 */\ + MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /* GPMC_A10 */\ + MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /* GPMC_D0 */\ + MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /* GPMC_D1 */\ + MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /* GPMC_D2 */\ + MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0)) /* GPMC_D3 */\ + MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0)) /* GPMC_D4 */\ + MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0)) /* GPMC_D5 */\ + MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0)) /* GPMC_D6 */\ + MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0)) /* GPMC_D7 */\ + MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0)) /* GPMC_D8 */\ + MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0)) /* GPMC_D9 */\ + MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0)) /* GPMC_D10 */\ + MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0)) /* GPMC_D11 */\ + MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0)) /* GPMC_D12 */\ + MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0)) /* GPMC_D13 */\ + MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0)) /* GPMC_D14 */\ + MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0)) /* GPMC_D15 */\ + MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /* GPMC_nCS0 */\ + MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) /* GPMC_nCS1 */\ + MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) /* GPIO_nCS2 */\ + MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /* GPIO_nCS3 */\ + MUX_VAL(CP(GPMC_NCS4), (IDIS | PTU | EN | M0)) /* GPMC_nCS4 */\ + MUX_VAL(CP(GPMC_NCS5), (IDIS | PTU | EN | M0)) /* GPMC_nCS5 */\ + MUX_VAL(CP(GPMC_NCS6), (IDIS | PTU | EN | M0)) /* GPMC_nCS6 */\ + MUX_VAL(CP(GPMC_NCS7), (IDIS | PTU | EN | M0)) /* GPMC_nCS7 */\ + MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0)) /* GPMC_CLK */\ + MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /* GPMC_nADV_ALE */\ + MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /* GPMC_nOE */\ + MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /* GPMC_nWE */\ + MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0)) /* GPMC_nBE0_CLE */\ + MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /* GPMC_nBE1 */\ + MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /* GPMC_nWP */\ + MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /* GPMC_WAIT0 */\ + MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | DIS | M4)) /* GPIO_64-ETH_NRST */\ + MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /* MMC1_CLK */\ + MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /* MMC1_CMD */\ + MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /* MMC1_DAT0 */\ + MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /* MMC1_DAT1 */\ + MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /* MMC1_DAT2 */\ + MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /* MMC1_DAT3 */\ + MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) /* UART3_TX */\ + MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) /* UART3_RX */\ + MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /* I2C1_SCL */\ + MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /* I2C1_SDA */\ + MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) /* I2C4_SCL */\ + MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) /* I2C4_SDA */\ + MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /* SYS_32K */\ + MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /* GPIO_2 */\ + MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /* GPIO_3 */\ + MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /* GPIO_4 */\ + MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /* GPIO_5 */\ + MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /* GPIO_6 */\ + MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /* GPIO_7 */\ + MUX_VAL(CP(SYS_BOOT6), (IEN | PTD | DIS | M4)) /* GPIO_8 */\ + MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /* SDRC_CKE0 */\ + MUX_VAL(CP(SDRC_CKE1), (IDIS | PTU | EN | M0)) /* SDRC_CKE1 */ +#endif boards.cfg +1
-0@@ -262,6 +262,7 @@ omap4_panda arm armv7 panda ti omap4 omap4_sdp4430 arm armv7 sdp4430 ti omap4 am3517_evm arm armv7 am3517evm logicpd omap3 devkit8000 arm armv7 devkit8000 timll omap3 +igep0020 arm armv7 igep0020 isee omap3 s5p_goni arm armv7 goni samsung s5pc1xx smdkc100 arm armv7 smdkc100 samsung s5pc1xx ixdpg425 arm ixpinclude/configs/igep0020.h new file +218
-0@@ -0,0 +1,228 @@ +/* +* (C) Copyright 2010 +* ISEE 2007 SL, <www.iseebcn.com> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H +#include <asm/sizes.h> + +/* +* High Level Configuration Options +*/ +#define CONFIG_ARMV7 1/* This is an ARM V7 CPU core */ +#define CONFIG_OMAP 1/* in a TI OMAP core */ +#define CONFIG_OMAP34XX 1/* which is a 34XX */ +#define CONFIG_OMAP3430 1/* which is in a 3430 */ +#define CONFIG_OMAP3_IGEP0020 1/* working with IGEP0020 */ + +#define CONFIG_SDRC /* The chip has SDRC controller */ + +#include <asm/arch/cpu.h> +#include <asm/arch/omap3.h> + +/* +* Display CPU and Board information +*/ +#define CONFIG_DISPLAY_CPUINFO 1 +#define CONFIG_DISPLAY_BOARDINFO 1 + +/* Clock Defines */ +#define V_OSCK 26000000/* Clock output from T2 */ +#define V_SCLK (V_OSCK >> 1) + +#define CONFIG_MISC_INIT_R + +#define CONFIG_CMDLINE_TAG 1/* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 +#define CONFIG_REVISION_TAG 1 + +/* +* NS16550 Configuration +*/ + +#define V_NS16550_CLK 48000000/* 48MHz (APLL96/2) */ + +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK + +/* select serial console configuration */ +#define CONFIG_CONS_INDEX 3 +#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 +#define CONFIG_SERIAL3 3 + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200} +#define CONFIG_MMC 1 +#define CONFIG_OMAP3_MMC 1 +#define CONFIG_DOS_PARTITION 1 + +/* DDR */ +#define CONFIG_OMAP3_NUMONYX_DDR 1 + +/* USB */ +#define CONFIG_MUSB_UDC 1 +#define CONFIG_USB_OMAP3 1 +#define CONFIG_TWL4030_USB 1 + +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 + +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "IGEP" + +/* commands to include */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_EXT2 /* EXT2 Support */ +#define CONFIG_CMD_FAT /* FAT support */ +#define CONFIG_CMD_I2C /* I2C serial bus support */ +#define CONFIG_CMD_MMC /* MMC support */ +#define CONFIG_CMD_ONENAND /* ONENAND support */ +#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_NFS /* NFS support */ +#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ +#define CONFIG_MTD_DEVICE + +#undef CONFIG_CMD_FLASH/* flinfo, erase, protect */ +#undef CONFIG_CMD_IMLS/* List all found images */ + +#define CONFIG_SYS_NO_FLASH +#define CONFIG_HARD_I2C 1 +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_BUS 0 +#define CONFIG_SYS_I2C_BUS_SELECT 1 +#define CONFIG_DRIVER_OMAP34XX_I2C 1 + +/* +* TWL4030 +*/ +#define CONFIG_TWL4030_POWER 1 + +/* Environment information */ +#define CONFIG_BOOTCOMMAND \ + "mmc init 0 ; fatload mmc 0 0x80000000 setup.ini ; source \0" + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "usbtty=cdc_acm\0" + +#define CONFIG_AUTO_COMPLETE 1 + +/* +* Miscellaneous configurable options +*/ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_PROMPT "U-Boot # " +#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16/* max number of command args */ +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) + +#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)/* memtest */ +/* works on */ +#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ + 0x01F00000)/* 31MB */ + +#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)/* default */ +/* load address */ + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) + +/* +* OMAP3 has 12 GP timers, they can be driven by the system clock +* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). +* This rate is divided by a local divisor. +*/ +#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) +#define CONFIG_SYS_PTV 2/* Divisor: 2^(PTV+1) => 8 */ +#define CONFIG_SYS_HZ 1000 + +/* +* Stack sizes +* +* The stack sizes are set up in start.S using the settings below +*/ +#define CONFIG_STACKSIZE (128 << 10)/* regular stack 128 KiB */ + +/* +* Physical Memory Map +* +*/ +#define CONFIG_NR_DRAM_BANKS 2/* CS1 may or may not be populated */ +#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 +#define PHYS_SDRAM_1_SIZE (32 << 20)/*@least 32 meg */ +#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 + +/* SDRAM Bank Allocation method */ +#define SDRC_R_B_C 1 + +/* +* FLASH and environment organization +*/ + +#define PISMO1_ONEN_SIZE GPMC_SIZE_128M/* Configure the PISMO */ + +#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP + +#define ONENAND_ENV_OFFSET 0x260000/* environment starts here */ + +#define CONFIG_ENV_IS_IN_ONENAND 1 +#define CONFIG_ENV_SIZE (512 << 10)/* Total Size Environment */ +#define CONFIG_ENV_ADDR ONENAND_ENV_OFFSET + +/* +* Size of malloc() pool +*/ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) +#define CONFIG_SYS_GBL_DATA_SIZE 128/* bytes for initial data */ + +/* +* SMSC911x Ethernet +*/ +#if defined(CONFIG_CMD_NET )
include/configs/igep0020.h line 228
Quoted 10 lines
include/configs/igep0020.h new file +10
-0+#define CONFIG_NET_MULTI +#define CONFIG_SMC911X +#define CONFIG_SMC911X_32_BIT +#define CONFIG_SMC911X_BASE 0x2C000000 +#endif /* (CONFIG_CMD_NET) */ + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE) + +#endif /* __CONFIG_H */
I did both build and run tests on the v3 patch series.
There is one warning in the build:
igep0020.c: In function 'board_eth_init':
igep0020.c:125: warning: implicit declaration of function 'smc911x_initialize'
If this is fixed you have my:
v3 cover Add support for the IGEP v2 board.
In reply to Enric Balletbo i SerraQuoted 18 lines · Enric Balletbo i Serra
Hello,
This is the version 3 of patch series to add initial support for OMAP3 IGEP v2 board.
CHANGES:
* since v2
- [1/3] keep lists sorted
- [2/3] fix multiline comment style
- [3/3] add entry toMAINTAINERS* since v1
- [2/3] fix parens inNUMONYX_V_ACTIMB_165define
- [3/3] add extra space after first&ctrl_basein fileigep0020.c
- [3/3] add a space after the 57600 comma in fileigep0020.h
- [3/3] removeCONFIG_SYS_ARM_WITHOUT_RELOCundef
Quoted 13 lines
$ git diff --stat origin/master MAINTAINERS | 4 + MAKEALL | 1 + arch/arm/include/asm/arch-omap3/mem.h | 43 ++++++ board/isee/igep0020/Makefile | 49 +++++++ board/isee/igep0020/config.mk | 33 +++++ board/isee/igep0020/igep0020.c | 128 ++++++++++++++++++ board/isee/igep0020/igep0020.h | 156 ++++++++++++++++++++++ boards.cfg | 1 + drivers/mtd/onenand/onenand_base.c | 1 + include/configs/igep0020.h | 228 +++++++++++++++++++++++++++++++++ include/linux/mtd/onenand.h | 1 + 11 files changed, 645 insertions(+), 0 deletions(-)
I noticed that you are using the legacy mmc driver.
I've submitted a patch series to add support for the generic mmc driver on OMAP3 and OMAP4.
Once this is upstream you might want to consider sending a patch to switch IGEP v2 from the legacy driver to the generic driver.
Steve
v3 cover Add support for the IGEP v2 board.
Hello,
2010/10/11 Steve Sakoman <[email protected]>:
Quoted 33 lines · Enric Balletbo i Serra
Quoted 18 lines
Hello,
This is the version 3 of patch series to add initial support for OMAP3 IGEP v2 board.
CHANGES:
* since v2
? ? - [1/3] keep lists sorted
? ? - [2/3] fix multiline comment style
? ? - [3/3] add entry toMAINTAINERS* since v1
? ? - [2/3] fix parens inNUMONYX_V_ACTIMB_165define
? ? - [3/3] add extra space after first&ctrl_basein fileigep0020.c? ? - [3/3] add a space after the 57600 comma in fileigep0020.h? ? - [3/3] removeCONFIG_SYS_ARM_WITHOUT_RELOCundefQuoted 13 lines
$ git diff --stat origin/master ?MAINTAINERS ? ? ? ? ? ? ? ? ? ? ? ? ? | ? ?4 + ?MAKEALL ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? | ? ?1 + ?arch/arm/include/asm/arch-omap3/mem.h | ? 43 ++++++ ?board/isee/igep0020/Makefile ? ? ? ? ?| ? 49 +++++++ ?board/isee/igep0020/config.mk ? ? ? ? | ? 33 +++++ ?board/isee/igep0020/igep0020.c ? ? ? ?| ?128 ++++++++++++++++++ ?board/isee/igep0020/igep0020.h ? ? ? ?| ?156 ++++++++++++++++++++++ ?boards.cfg ? ? ? ? ? ? ? ? ? ? ? ? ? ?| ? ?1 + ?drivers/mtd/onenand/onenand_base.c ? ?| ? ?1 + ?include/configs/igep0020.h ? ? ? ? ? ?| ?228 +++++++++++++++++++++++++++++++++ ?include/linux/mtd/onenand.h ? ? ? ? ? | ? ?1 + ?11 files changed, 645 insertions(+), 0 deletions(-)
Quoted 1 line
I noticed that you are using the legacy mmc driver.
Yes.
Quoted 3 lines
I've submitted a patch series to add support for the generic mmc driver on OMAP3 and OMAP4.
Ok
Quoted 3 lines
Once this is upstream you might want to consider sending a patch to switch IGEP v2 from the legacy driver to the generic driver.
I'll do.
I'll fix one build warning in version 4
igep0020.c: In function 'board_eth_init':
igep0020.c:125: warning: implicit declaration of function 'smc911x_initialize'
but first I've a question. Some people acked and tested my patches, when I send the version 4. I need to add these acks in my patch or are automatically added ?
Cheers,
Enric
v3 cover Add support for the IGEP v2 board.
Quoted 54 lines · Enric Balletb? i Serra
Hello,
2010/10/11 Steve Sakoman <[email protected]>:
Quoted 33 lines · Enric Balletbo i Serra
Quoted 18 lines
Hello,
This is the version 3 of patch series to add initial support for OMAP3 IGEP v2 board.
CHANGES:
* since v2
? ? - [1/3] keep lists sorted
? ? - [2/3] fix multiline comment style
? ? - [3/3] add entry toMAINTAINERS* since v1
? ? - [2/3] fix parens inNUMONYX_V_ACTIMB_165define
? ? - [3/3] add extra space after first&ctrl_basein fileigep0020.c? ? - [3/3] add a space after the 57600 comma in fileigep0020.h? ? - [3/3] removeCONFIG_SYS_ARM_WITHOUT_RELOCundefQuoted 13 lines
$ git diff --stat origin/master ?MAINTAINERS ? ? ? ? ? ? ? ? ? ? ? ? ? | ? ?4 + ?MAKEALL ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? | ? ?1 + ?arch/arm/include/asm/arch-omap3/mem.h | ? 43 ++++++ ?board/isee/igep0020/Makefile ? ? ? ? ?| ? 49 +++++++ ?board/isee/igep0020/config.mk ? ? ? ? | ? 33 +++++ ?board/isee/igep0020/igep0020.c ? ? ? ?| ?128 ++++++++++++++++++ ?board/isee/igep0020/igep0020.h ? ? ? ?| ?156 ++++++++++++++++++++++ ?boards.cfg ? ? ? ? ? ? ? ? ? ? ? ? ? ?| ? ?1 + ?drivers/mtd/onenand/onenand_base.c ? ?| ? ?1 + ?include/configs/igep0020.h ? ? ? ? ? ?| ?228 +++++++++++++++++++++++++++++++++ ?include/linux/mtd/onenand.h ? ? ? ? ? | ? ?1 + ?11 files changed, 645 insertions(+), 0 deletions(-)Quoted 1 line
I noticed that you are using the legacy mmc driver.
Yes.
Quoted 3 lines
I've submitted a patch series to add support for the generic mmc driver on OMAP3 and OMAP4.
Ok
Quoted 3 lines
Once this is upstream you might want to consider sending a patch to switch IGEP v2 from the legacy driver to the generic driver.
I'll do.
I'll fix one build warning in version 4
Quoted 7 lines
igep0020.c: In function 'board_eth_init':
igep0020.c:125: warning: implicit declaration of function 'smc911x_initialize'but first I've a question. Some people acked and tested my patches, when I send the version 4. I need to add these acks in my patch or are automatically added ?
I typically add any Acks/Testeds I've received in the next revision. It will save Sandeep a little work if he doesn't have to manually add them :-)
Steve