mx6dl: Add initial support for Wandboard dual lite
PATCH 1/1 mx6dl: Add initial support for Wandboard dual lite
From: Fabio Estevam <[email protected]>
Add initial support for Wandboard dual lite.
Wandboard is a development board that has two variants: one version based on mx6 dual lite and another one based on mx6 solo.
For details on the features of Wandboard, please refer to:
http://www.wandboard.org/
---
This applies on top of Eric's series for adding nitrogen6x boards support.
MAINTAINERS | 1 + arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 3 + board/wandboard/Makefile | 29 ++++ board/wandboard/wandboard.c | 180 ++++++++++++++++++++++++ boards.cfg | 1 + include/configs/wandboard.h | 210 ++++++++++++++++++++++++++++ 6 files changed, 424 insertions(+) create mode 100644 board/wandboard/Makefile create mode 100644 board/wandboard/wandboard.c create mode 100644 include/configs/wandboard.h
MAINTAINERS +1 -0
@@ -659,6 +659,7 @@ Fabio Estevam <[email protected]> mx53smd i.MX53 mx6qsabresd i.MX6Q mx6qsabreauto i.MX6Q + wandboard i.MX6DL Daniel Gorsulowski <[email protected]>
arch/arm/include/asm/arch-mx6/mx6dl_pins.h +3 -0
@@ -50,6 +50,8 @@#define NO_MUX_I 0#define NO_PAD_I 0enum { +MX6_PAD_CSI0_DAT10__UART1_TXD =IOMUX_PAD (0x0360 ,0x004C ,3 ,0x0000 ,0 ,0 ), +MX6_PAD_CSI0_DAT11__UART1_RXD =IOMUX_PAD (0x0364 ,0x0050 ,3 ,0x08FC ,1 ,0 ),MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK =IOMUX_PAD (0x03B0 ,0x009C ,0 ,0x0000 ,0 , PAD_CTL_DSE_120ohm),MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15 =IOMUX_PAD (0x03B4 ,0x00A0 ,0 ,0x0000 ,0 , PAD_CTL_DSE_120ohm),MX6_PAD_DI0_PIN2__IPU1_DI0_PIN2 =IOMUX_PAD (0x03B8 ,0x00A4 ,0 ,0x0000 ,0 , PAD_CTL_DSE_120ohm),
@@ -90,6 +92,7 @@ enum {MX6_PAD_EIM_D27__UART2_RXD =IOMUX_PAD (0x0540 ,0x0170 ,4 ,0x0904 ,1 ,0 ),MX6_PAD_EIM_D28__I2C1_SDA =IOMUX_PAD (0x0544 ,0x0174 ,1 |IOMUX_CONFIG_SION ,0x086C ,1 ,0 ),MX6_PAD_EIM_D28__GPIO_3_28 =IOMUX_PAD (0x0544 ,0x0174 ,5 ,0x0000 ,0 ,0 ), +MX6_PAD_EIM_D29__GPIO_3_29 =IOMUX_PAD (0x0548 ,0x0178 ,5 ,0x0000 ,0 ,0 ),MX6_PAD_ENET_MDC__ENET_MDC =IOMUX_PAD (0x05B8 ,0x01E8 ,1 ,0x0000 ,0 ,0 ),MX6_PAD_ENET_MDIO__ENET_MDIO =IOMUX_PAD (0x05BC ,0x01EC ,1 ,0x0810 ,0 ,0 ), MX6_PAD_ENET_REF_CLK__ENET_TX_CLK = IOMUX_PAD(0x05C0, 0x01F0, 1, 0x0000, 0, 0),
board/wandboard/Makefile new file +29 -0
@@ -0,0 +1,29 @@ +# +# (C) Copyright 2013 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := wandboard.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################
board/wandboard/wandboard.c new file +180 -0
180 lines not on this page · raw message
boards.cfg +1 -0
@@ -259,6 +259,7 @@ nitrogen6q arm armv7 nitrogen6x boundar nitrogen6q2g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q2g.cfg,MX6Q nitrogen6s arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S nitrogen6s1g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s1g.cfg,MX6S +wandboard_dl arm armv7 wandboard - mx6 wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL cm_t35 arm armv7 cm_t35 - omap3 omap3_overo arm armv7 overo - omap3 omap3_pandora arm armv7 pandora - omap3
include/configs/wandboard.h new file +210 -0
210 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH 1/1 mx6dl: Add initial support for Wandboard dual lite
Dear Fabio Estevam,
Quoted 2 lines · In message <[email protected]> you wrote:
Add initial support for Wandboard dual lite.
Thanks!
board/wandboard/wandboard.c line 44
Quoted 3 lines
board/wandboard/wandboard.c new file +3
-0+int dram_init (void ) +{ + gd->ram_size =imx_ddr_size ();
Can we please use get_ram_size() to verify / test the actual RAM size?
Quoted 1 line
+#define
CONFIG_ARP_TIMEOUT200UL
Is this really needed?
include/configs/wandboard.h line 183
Quoted 4 lines
include/configs/wandboard.h new file +4
-0+/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR +#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
What is the "1u *" needed for?
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de If in any problem you find yourself doing an immense amount of work, the answer can be obtained by simple inspection.