ARM: mach-moxart: add MOXA ART SoC files
Subsystems (4)
PATCH v2 1/3 ARM: mach-moxart: add MOXA ART SoC files
Add MOXA ART SoC support.
The MOXA ART SoC is based on a Faraday FA526 ARMv4 32-bit 192 MHz CPU with MMU and 16KB/8KB D/I-cache (UC-7112-LX). Used on models UC-7101, UC-7112/UC-7110, IA240/IA241, IA3341.
--- arch/arm/Kconfig | 2 + arch/arm/Makefile | 1 + arch/arm/configs/moxart_uc7112lx_defconfig | 111 ++++++++++++++++++++++++++++ arch/arm/mach-moxart/Kconfig | 28 +++++++ arch/arm/mach-moxart/Makefile | 3 + arch/arm/mach-moxart/moxart.c | 33 ++++++++ 6 files changed, 178 insertions(+), 0 deletions(-) create mode 100644 arch/arm/configs/moxart_uc7112lx_defconfig create mode 100644 arch/arm/mach-moxart/Kconfig create mode 100644 arch/arm/mach-moxart/Makefile create mode 100644 arch/arm/mach-moxart/moxart.c
arch/arm/Kconfig +2 -0
@@ -938,6 +938,8 @@ source "arch/arm/mach-footbridge/Kconfig" source "arch/arm/mach-gemini/Kconfig" +source "arch/arm/mach-moxart/Kconfig" + source "arch/arm/mach-highbank/Kconfig" source "arch/arm/mach-integrator/Kconfig"
arch/arm/Makefile +1 -0
@@ -148,6 +148,7 @@ machine-$(CONFIG_ARCH_DOVE) += dove machine-$(CONFIG_ARCH_EBSA110) += ebsa110 machine-$(CONFIG_ARCH_EP93XX) += ep93xx machine-$(CONFIG_ARCH_GEMINI) += gemini +machine-$(CONFIG_ARCH_MOXART) += moxart machine-$(CONFIG_ARCH_HIGHBANK) += highbank machine-$(CONFIG_ARCH_INTEGRATOR) += integrator machine-$(CONFIG_ARCH_IOP13XX) += iop13xx
arch/arm/configs/moxart_uc7112lx_defconfig new file +111 -0
111 lines not on this page · raw message
arch/arm/mach-moxart/Kconfig new file +28 -0
@@ -0,0 +1,28 @@ +config ARCH_MOXART + bool "MOXA ART SoC" if ARCH_MULTI_V4 + select CPU_FA526 + select ARM_DMA_MEM_BUFFERABLE + select USE_OF + select CLKSRC_OF + select HAVE_CLK + select COMMON_CLK + select GENERIC_IRQ_CHIP + select ARCH_REQUIRE_GPIOLIB + help + Say Y here if you want to run your kernel on hardware with a + MOXA ART SoC. + The MOXA ART SoC is based on a Faraday FA526 ARMv4 32-bit + 192 MHz CPU with MMU and 16KB/8KB D/I-cache (UC-7112-LX). + Used on models UC-7101, UC-7112/UC-7110, IA240/IA241, IA3341. + +if ARCH_MOXART + +config MACH_UC7112LX + bool "MOXA UC-7112-LX" + depends on ARCH_MOXART + default y + help + Say Y here if you intend to run this kernel on a MOXA + UC-7112-LX embedded computer. + +endif
arch/arm/mach-moxart/Makefile new file +3 -0
@@ -0,0 +1,3 @@ +# Object file lists. + +obj-$(CONFIG_MACH_UC7112LX) += moxart.o
arch/arm/mach-moxart/moxart.c new file +33 -0
@@ -0,0 +1,33 @@ +/* +* arch/arm/mach-moxart/moxart.c +* +* (C) Copyright 2013, Jonas Jensen <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#include <linux/init.h> + +#include <asm/mach/arch.h> + +static const char *const moxart_dt_compat[] = { +"moxa,moxart" , +NULL , +}; + +DT_MACHINE_START (MOXART ,"MOXA UC-7112-LX" ) + .dt_compat = moxart_dt_compat, +MACHINE_END
Signature · 1 line
1.7.2.5
PATCH v2 2/3 ARM: mach-moxart: add MOXA ART device tree files
Add generic SoC include and UC-7112-LX platform device tree files. Add device tree bindings documentation.
--- Documentation/devicetree/bindings/arm/moxart.txt | 8 +++ .../arm/moxart/moxart-interrupt-controller.txt | 29 +++++++++ .../bindings/arm/moxart/moxart-timer.txt | 17 ++++++ arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/moxart-uc7112lx.dts | 61 ++++++++++++++++++++ arch/arm/boot/dts/moxart.dtsi | 60 +++++++++++++++++++ 6 files changed, 176 insertions(+), 0 deletions(-) create mode 100644 Documentation/devicetree/bindings/arm/moxart.txt create mode 100644 Documentation/devicetree/bindings/arm/moxart/moxart-interrupt-controller.txt create mode 100644 Documentation/devicetree/bindings/arm/moxart/moxart-timer.txt create mode 100644 arch/arm/boot/dts/moxart-uc7112lx.dts create mode 100644 arch/arm/boot/dts/moxart.dtsi
Documentation/devicetree/bindings/arm/moxart.txt new file +8 -0
@@ -0,0 +1,8 @@ +MOXA ART device tree bindings +------------------------------------------- + +Boards with the MOXA ART SoC shall have the following properties: + +Required root node property: + +compatible = "moxa,moxart";
Documentation/devicetree/bindings/arm/moxart/moxart-interrupt-controller.txt new file +29 -0
@@ -0,0 +1,29 @@ +* MOXA ART Interrupt Controller + +MOXA ART Interrupt Controller (moxart-interrupt-controller) is used on +MOXA ART SoCs and supports 32 non-configurable number of interrupts + +Main node required properties: + +- compatible : should be: + "moxa,moxart-interrupt-controller" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 2. + + The first cell contains the interrupt number in the range [0-31]. + The second cell contains the interrupt type +- reg: physical base address and size of the intc registers map. +- interrupt-mask: Specifies if the interrupt is edge or level-triggered + each bit represent an interrupt 0-31 where 1 signify edge + +Example: + + intc: interrupt-controller at 98800000 { + compatible = "moxa,moxart-interrupt-controller"; + reg = <0x98800000 0x38>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-mask = <0x00080000>; + }; +
Documentation/devicetree/bindings/arm/moxart/moxart-timer.txt new file +17 -0
@@ -0,0 +1,17 @@ +MOXA ART timer +----------------------------------------------------- +This timer is used on MOXA ART SoCs: + +Required properties: +- compatible : "moxa,moxart-timer" +- reg : Register range for the timer +- interrupts : interrupt for the timer + +Example: + + timer: timer at 98400000 { + compatible = "moxa,moxart-timer"; + reg = <0x98400000 0x10>; + interrupts = <19 1>; + }; +
arch/arm/boot/dts/Makefile +1 -0
@@ -219,6 +219,7 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \ wm8750-apc8750.dtb \ wm8850-w70v2.dtb dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb +dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb targets += dtbs targets += $(dtb-y)
arch/arm/boot/dts/moxart-uc7112lx.dts new file +61 -0
61 lines not on this page · raw message
arch/arm/boot/dts/moxart.dtsi new file +60 -0
60 lines not on this page · raw message
Signature · 1 line
1.7.2.5
PATCH v2 3/3 ARM: mach-moxart: add MOXA ART UART debug files
In reply to Jonas JensenAdd MOXA ART kernel low-level debugging port support.
--- arch/arm/Kconfig.debug | 8 ++++++++ arch/arm/include/debug/moxart.S | 16 ++++++++++++++++ 2 files changed, 24 insertions(+), 0 deletions(-) create mode 100644 arch/arm/include/debug/moxart.S
arch/arm/Kconfig.debug +8 -0
@@ -447,6 +447,13 @@ choice Say Y here if you want kernel low-level debugging support on Allwinner A1X based platforms on the UART1. + config DEBUG_MOXART_UART0 + bool "Kernel low-level debugging messages via MOXART UART0" + depends on ARCH_MOXART + help + Say Y here if you want kernel low-level debugging support + on MOXART based platforms on the UART0. + config DEBUG_TEGRA_UART depends on ARCH_TEGRA bool "Use Tegra UART for low-level debug"
@@ -668,6 +675,7 @@ config DEBUG_LL_INCLUDE default "debug/sirf.S" if DEBUG_SIRFPRIMA2_UART1 || DEBUG_SIRFMARCO_UART1 default "debug/socfpga.S" if DEBUG_SOCFPGA_UART default "debug/sunxi.S" if DEBUG_SUNXI_UART0 || DEBUG_SUNXI_UART1 + default "debug/moxart.S" if DEBUG_MOXART_UART0 default "debug/tegra.S" if DEBUG_TEGRA_UART default "debug/ux500.S" if DEBUG_UX500_UART default "debug/vexpress.S" if DEBUG_VEXPRESS_UART0_DETECT || \
arch/arm/include/debug/moxart.S new file +16 -0
@@ -0,0 +1,16 @@ +/* Copyright (C) 2013 Jonas Jensen <[email protected]> + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, + * or (at your option) any later version. */ + +#define MOXART_UART_DEBUG_PHYS_BASE 0x98200000 +#define MOXART_UART_DEBUG_VIRT_BASE 0xf9820000 + +.macro addruart, rp, rv, tmp + ldr \rp, =MOXART_UART_DEBUG_PHYS_BASE + ldr \rv, =MOXART_UART_DEBUG_VIRT_BASE +.endm + +#define UART_SHIFT 2 +#include <asm/hardware/debug-8250.S>
Signature · 1 line
1.7.2.5
I may have submitted this one too early. There are now a few things I want to address:
* rename moxart_uc7112lx_defconfig moxart_defconfig
* remove MACH_UC7112LX "default y" from arch/arm/mach-moxart/Kconfig
Also, the omitted arch/arm/mach-moxart/idle.c hinges on a patch now submitted to Russell's patch tracker:
http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=7760/1
Best regards,
Jonas