hwmon: ina2xx: implement chip reinitialization and add new attributes
Subsystems (2)
v8 cover hwmon: ina2xx: implement chip reinitialization and add new attributes
This series implements a mechanism to detect if the chip is in its POR state and reinitialize it if needed. It also extends the sysfs interface to make the driver configurable at run-time.
The shunt_resistor attribute allows to change the shunt resistance value at run-time in cases where ina2xx used to do the measurement isn't integrated with the shunt.
The avg_rate attribute allows to increase/decrease noise reduction.
v8:
- accept averaging rate values more flexibly and round them to the nearest correct value
- don't call ina2xx_update_device() in ina226_set_avg()
- make sure the registers are going to be re-read after setting the averaging rate
v7:
https://www.mail-archive.com/linux-kernel%40vger.kernel.org/msg787851.html
Bartosz Golaszewski (5):
hwmon: ina2xx: reinitialize the chip in case it's been reset
hwmon: ina2xx: remove a stray new line
hwmon: ina2xx: don't accept shunt values greater than the calibration factor
hwmon: ina2xx: make shunt resistance configurable at run-time
hwmon: ina2xx: allow to change the averaging rate at run-time
Documentation/hwmon/ina2xx | 8 +- drivers/hwmon/ina2xx.c | 301 +++++++++++++++++++++++++++++++++++++++------ 2 files changed, 266 insertions(+), 43 deletions(-)
Signature · 7 lines
2.1.3 _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
PATCH v8 1/5 hwmon: ina2xx: reinitialize the chip in case it's been reset
Chips from the ina family don't like to be uninitialized. In case the power is cut-off and restored again the calibration register will be reset to 0 and both the power and current registers will remain at 0.
Check the calibration register in ina2xx_update_device() and reinitialize the chip if needed.
--- drivers/hwmon/ina2xx.c | 128 +++++++++++++++++++++++++++++++++++-------------- 1 file changed, 91 insertions(+), 37 deletions(-)
drivers/hwmon/ina2xx.c +91 -37
@@ -35,6 +35,7 @@#include <linux/hwmon-sysfs.h> #include <linux/jiffies.h> #include <linux/of.h> +#include <linux/delay.h> #include <linux/platform_data/ina2xx.h>
@@ -64,6 +65,9 @@/* worst case is 68.10 ms (~14.6Hz, ina219) */ #define INA2XX_CONVERSION_RATE 15 +#define INA2XX_MAX_DELAY 69/* worst case delay in ms */ + +#define INA2XX_RSHUNT_DEFAULT 10000enum ina2xx_ids { ina219, ina226 };
@@ -81,6 +85,8 @@ struct ina2xx_data {struct i2c_client *client;const struct ina2xx_config *config; +long rshunt; +struct mutex update_lock;bool valid;unsigned long last_updated;
@@ -110,34 +116,96 @@ static const struct ina2xx_config ina2xx_config[] = { }, }; -static struct ina2xx_data *ina2xx_update_device (struct device *dev) +/* +* Initialize the configuration and calibration registers. +*/ +static int ina2xx_init (struct ina2xx_data *data) { -struct ina2xx_data *data =dev_get_drvdata (dev);struct i2c_client *client = data->client; -struct ina2xx_data *ret = data; +int ret; -mutex_lock (&data->update_lock); +/* device configuration */ + ret =i2c_smbus_write_word_swapped (client,INA2XX_CONFIG , + data->config->config_default); +if (ret <0 ) +return ret; -if (time_after (jiffies, data->last_updated + -HZ /INA2XX_CONVERSION_RATE ) || !data->valid) { +/* +* Set current LSB to 1mA, shunt is in uOhms +* (equation 13 in datasheet). +*/ +return i2c_smbus_write_word_swapped (client,INA2XX_CALIBRATION , + data->config->calibration_factor / data->rshunt); +} -int i; +static int ina2xx_do_update (struct device *dev) +{ +struct ina2xx_data *data =dev_get_drvdata (dev); +struct i2c_client *client = data->client; +int i, rv, retry; -dev_dbg (&client->dev,"Starting ina2xx update\n" ); +dev_dbg (&client->dev,"Starting ina2xx update\n" ); +for (retry =5 ; retry; retry--) {/* Read all registers */ for (i =0 ; i < data->config->registers; i++) { -int rv =i2c_smbus_read_word_swapped (client, i); -if (rv <0 ) { - ret =ERR_PTR (rv); - goto abort; - } + rv =i2c_smbus_read_word_swapped (client, i); +if (rv <0 ) +return rv; data->regs[i] = rv; } + +/* +* If the current value in the calibration register is 0, the +* power and current registers will also remain at 0. In case +* the chip has been reset let's check the calibration +* register and reinitialize if needed. +*/ +if (data->regs[INA2XX_CALIBRATION ] =0 ) { +dev_warn (dev,"chip not calibrated, reinitializing\n" ); + + rv =ina2xx_init (data); +if (rv <0 ) +return rv; + +/* +* Let's make sure the power and current registers +* have been updated before trying again. +*/ +msleep (INA2XX_MAX_DELAY ); +continue ; + } + data->last_updated = jiffies; data->valid =1 ; + +return 0 ; } -abort: + +/* +* If we're here then although all write operations succeeded, the +* chip still returns 0 in the calibration register. Nothing more we +* can do here. +*/ +dev_err (dev,"unable to reinitialize the chip\n" ); +return -ENODEV ; +} + +static struct ina2xx_data *ina2xx_update_device (struct device *dev) +{ +struct ina2xx_data *data =dev_get_drvdata (dev); +struct ina2xx_data *ret = data; +int rv; + +mutex_lock (&data->update_lock); + +if (time_after (jiffies, data->last_updated + +HZ /INA2XX_CONVERSION_RATE ) || !data->valid) { + rv =ina2xx_do_update (dev); +if (rv <0 ) + ret =ERR_PTR (rv); + } +mutex_unlock (&data->update_lock);return ret; }
@@ -221,7 +289,6 @@ static int ina2xx_probe(struct i2c_client *client,struct device *dev = &client->dev;struct ina2xx_data *data;struct device *hwmon_dev; -long shunt =10000 ;/* default shunt value 10mOhms */ u32 val;int ret;
@@ -234,41 +301,28 @@ static int ina2xx_probe(struct i2c_client *client,if (dev_get_platdata (dev)) { pdata =dev_get_platdata (dev); - shunt = pdata->shunt_uohms; + data->rshunt = pdata->shunt_uohms; }else if (!of_property_read_u32 (dev->of_node,"shunt-resistor" , &val)) { - shunt = val; + data->rshunt = val; + }else { + data->rshunt =INA2XX_RSHUNT_DEFAULT ; } -if (shunt <=0 ) -return -ENODEV ; -/* set the device type */ data->kind = id->driver_data; data->config = &ina2xx_config[data->kind]; + data->client = client; -/* device configuration */ - ret =i2c_smbus_write_word_swapped (client,INA2XX_CONFIG , - data->config->config_default); -if (ret <0 ) { -dev_err (dev, -"error writing to the config register: %d" , ret); +if (data->rshunt <=0 )return -ENODEV ; - } -/* -* Set current LSB to 1mA, shunt is in uOhms -* (equation 13 in datasheet). -*/ - ret =i2c_smbus_write_word_swapped (client,INA2XX_CALIBRATION , - data->config->calibration_factor / shunt); + ret =ina2xx_init (data);if (ret <0 ) { -dev_err (dev, -"error writing to the calibration register: %d" , ret); +dev_err (dev,"error configuring the device: %d\n" , ret);return -ENODEV ; } - data->client = client;mutex_init (&data->update_lock); hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
@@ -277,7 +331,7 @@ static int ina2xx_probe(struct i2c_client *client,return PTR_ERR (hwmon_dev);dev_info (dev,"power monitor %s (Rshunt = %li uOhm)\n" , - id->name, shunt); + id->name, data->rshunt);return 0 ; }
Signature · 7 lines
2.1.3 _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
PATCH v8 2/5 hwmon: ina2xx: remove a stray new line
In reply to Bartosz Golaszewski--- drivers/hwmon/ina2xx.c | 1 - 1 file changed, 1 deletion(-)
drivers/hwmon/ina2xx.c +0 -1
@@ -52,7 +52,6 @@#define INA226_ALERT_LIMIT 0x07#define INA226_DIE_ID 0xFF -/* register count */ #define INA219_REGISTERS 6#define INA226_REGISTERS 8
Signature · 7 lines
2.1.3 _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
PATCH v8 3/5 hwmon: ina2xx: don't accept shunt values greater than the calibration factor
In reply to Bartosz GolaszewskiShunt resistance values greater than the chip's calibration factor make no sense since the actual value written to the register equals:
<calibration factor> / <shunt>
Bail-out from ina2xx_probe() if the configured value is greater than the calibration factor.
--- drivers/hwmon/ina2xx.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/hwmon/ina2xx.c +2 -1
@@ -313,7 +313,8 @@ static int ina2xx_probe(struct i2c_client *client, data->config = &ina2xx_config[data->kind]; data->client = client; -if (data->rshunt <=0 ) +if (data->rshunt <=0 || + data->rshunt > data->config->calibration_factor)return -ENODEV ; ret =ina2xx_init (data);
Signature · 7 lines
2.1.3 _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
PATCH v8 4/5 hwmon: ina2xx: make shunt resistance configurable at run-time
In reply to Bartosz GolaszewskiThe shunt resistance can only be set via platform_data or device tree. This isn't suitable for devices in which the shunt resistance can change/isn't known at boot-time.
Add a sysfs attribute that allows to read and set the shunt resistance.
--- Documentation/hwmon/ina2xx | 5 +++-- drivers/hwmon/ina2xx.c | 48 ++++++++++++++++++++++++++++++++++++++++++++-- 2 files changed, 49 insertions(+), 4 deletions(-)
Documentation/hwmon/ina2xx +3 -2
@@ -44,6 +44,7 @@ The INA226 monitors both a shunt voltage drop and bus supply voltage. The INA230 is a high or low side current shunt and power monitor with an I2C interface. The INA230 monitors both a shunt voltage drop and bus supply voltage. -The shunt value in micro-ohms can be set via platform data or device tree. -Please refer to the Documentation/devicetree/bindings/i2c/ina2xx.txt for bindings +The shunt value in micro-ohms can be set via platform data or device tree at +compile-time or via the shunt_resistor attribute in sysfs at run-time. Please +refer to the Documentation/devicetree/bindings/i2c/ina2xx.txt for bindings if the device tree is used.
drivers/hwmon/ina2xx.c +46 -2
84 lines not on this page · raw message
Signature · 7 lines
2.1.3 _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
PATCH v8 5/5 hwmon: ina2xx: allow to change the averaging rate at run-time
In reply to Bartosz GolaszewskiThe averaging rate of ina226 is hardcoded to 16 in the driver. Make it modifiable at run-time via a new sysfs attribute.
While we're at it - add an additional variable to ina2xx_data, which holds the current configuration settings - this way we'll be able to restore the configuration in case of an unexpected chip reset.
--- Documentation/hwmon/ina2xx | 3 ++ drivers/hwmon/ina2xx.c | 129 +++++++++++++++++++++++++++++++++++++++++++-- 2 files changed, 128 insertions(+), 4 deletions(-)
Documentation/hwmon/ina2xx +3 -0
@@ -48,3 +48,6 @@ The shunt value in micro-ohms can be set via platform data or device tree at compile-time or via the shunt_resistor attribute in sysfs at run-time. Please refer to the Documentation/devicetree/bindings/i2c/ina2xx.txt for bindings if the device tree is used. + +The averaging rate of INA226 and INA230 can be changed via the avg_rate sysfs +attribute. The available rates are: 1, 4, 16, 64, 128, 256, 512 and 1024.
drivers/hwmon/ina2xx.c +125 -4
196 lines not on this page · raw message
Signature · 7 lines
2.1.3 _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Guenter Roeck
maintainerRe: [v8, 5/5] hwmon: ina2xx: allow to change the averaging rate at run-time
Quoted 18 lines · Bartosz Golaszewski
The averaging rate of ina226 is hardcoded to 16 in the driver. Make it modifiable at run-time via a new sysfs attribute.
While we're at it - add an additional variable to
ina2xx_data, which holds the current configuration settings - this way we'll be able to restore the configuration in case of an unexpected chip reset.Signed-off-by Bartosz Golaszewski <[email protected]>--- Documentation/hwmon/ina2xx | 3 ++ drivers/hwmon/ina2xx.c | 129 +++++++++++++++++++++++++++++++++++++++++++-- 2 files changed, 128 insertions(+), 4 deletions(-)Documentation/hwmon/ina2xx +0
-0
Documentation/hwmon/ina2xx The shunt value in micro-ohms can be set via platform data or device tree at · line 53
Quoted 6 lines
Documentation/hwmon/ina2xx +3
-0@@ -48,3 +48,6 @@ The shunt value in micro-ohms can be set via platform data or device tree at compile-time or via the shunt_resistor attribute in sysfs at run-time. Please refer to the Documentation/devicetree/bindings/i2c/ina2xx.txt for bindings if the device tree is used. + +The averaging rate of INA226 and INA230 can be changed via the avg_rate sysfs +attribute. The available rates are: 1, 4, 16, 64, 128, 256, 512 and 1024.
You do accept other values, so you might want to add that other values will be rounded to the above.
drivers/hwmon/ina2xx.c line 73
Quoted 11 lines
drivers/hwmon/ina2xx.c +3
-0@@ -68,6 +68,15 @@#define INA2XX_RSHUNT_DEFAULT 10000 +/* bit masks for the averaging setting in the configuration register */ +#define INA226_AVG_RD_MASK 0x0E00 +#define INA226_AVG_WR_MASK 0xF1FF
You could define INA226_AVG_MASK as 0x0e00 and use ~INA226_AVG_MASK to negate it. This is more common than the above and less error prone.
drivers/hwmon/ina2xx.c line 75
Quoted 2 lines
drivers/hwmon/ina2xx.c +2
-0+ +#define INA226_READ_AVG (reg) ((reg & INA226_AVG_RD_MASK) >> 9)
(reg)
Also, it might make sense to define INA226_AVG_SHIFT since you use it twice.
Quoted 46 lines
drivers/hwmon/ina2xx.c +26
-0+ +/* common attrs, ina226 attrs and NULL */ +#define INA2XX_MAX_ATTRIBUTE_GROUPS 3 +enum ina2xx_ids { ina219, ina226 };struct ina2xx_config {@@ -85,12 +94,14 @@ struct ina2xx_data {const struct ina2xx_config *config;long rshunt; +u16 curr_config;struct mutex update_lock;bool valid;unsigned long last_updated;int kind; +const struct attribute_group *groups[INA2XX_MAX_ATTRIBUTE_GROUPS ];u16 regs[INA2XX_MAX_REGISTERS ]; };@@ -115,6 +126,39 @@ static const struct ina2xx_config ina2xx_config[] = { }, }; +/* +* Available averaging rates for ina226. The indices correspond with +* the bit values expected by the chip (according to the ina226 datasheet, +* table 3 AVG bit settings, found at +* http://www.ti.com/lit/ds/symlink/ina226.pdf. +*/ +static const int ina226_avg_tab[] = {1 ,4 ,16 ,64 ,128 ,256 ,512 ,1024 }; + +static int ina226_avg_bits (int avg) +{ +int i; + +/* Get the closest average from the tab. */ +for (i =0 ; i <ARRAY_SIZE (ina226_avg_tab) -1 ; i++) { +if (avg <= (ina226_avg_tab[i] + ina226_avg_tab[i +1 ]) /2 ) +return i; + } + +return i;/* Return 0b0111 for other values. */ +}
drivers/hwmon/ina2xx.c static const struct ina2xx_config ina2xx_config[] = { · line 158
Quoted 10 lines
drivers/hwmon/ina2xx.c +10
-0+ +static int ina226_avg_val (int bits) +{ +/* +* Value read from the config register should be correct, but do check +* the boundary just in case. +*/ +if (bits >=ARRAY_SIZE (ina226_avg_tab)) +return -ENODEV ; +
Logically this can not happen, since the calling code uses INA226_READ_AVG() which can only return 0..7. So this check is really unnecessary. It might possibly make sense to pass in the configuration register value and apply INA226_READ_AVG in this function to make this more obvious. See more below, though; the function itself is unnecessary.
Quoted 25 lines
drivers/hwmon/ina2xx.c +10
-1+return ina226_avg_tab[bits]; +} +static int ina2xx_calibrate (struct ina2xx_data *data) { return i2c_smbus_write_word_swapped(data->client, INA2XX_CALIBRATION,@@ -131,7 +175,7 @@ static int ina2xx_init(struct ina2xx_data *data)/* device configuration */ ret =i2c_smbus_write_word_swapped (client,INA2XX_CONFIG , - data->config->config_default); + data->curr_config);if (ret <0 )return ret;@@ -292,6 +336,62 @@ static ssize_t ina2xx_set_shunt(struct device *dev,return count; } +static ssize_t ina226_show_avg (struct device *dev, +struct device_attribute *da,char *buf) +{ +struct ina2xx_data *data =ina2xx_update_device (dev); +int avg, i; +
drivers/hwmon/ina2xx.c static ssize_t ina2xx_set_shunt(struct device *dev, · line 354
Quoted 10 lines
drivers/hwmon/ina2xx.c +10
-0+if (IS_ERR (data)) +return PTR_ERR (data); + + avg =ina226_avg_val (INA226_READ_AVG (data->regs[INA2XX_CONFIG ])); +if (avg <0 ) +return avg; + +for (i =0 ; i <ARRAY_SIZE (ina226_avg_tab); i++) { +if (avg = ina226_avg_tab[i]) +break ;
ina226_avg_val() calculates the average value from ina226_avg_tab and then you loop through ina226_avg_tab to find the index into ina226_avg_tab again, only to use the thus calculated index for accessing ina226_avg_tab[] once more. Think about it. A simple
avg = ina226_avg_tab[INA226_READ_AVG(data->regs[INA2XX_CONFIG])]; return snprintf(buf, PAGE_SIZE, "%d\n", avg); or even return snprintf(buf, PAGE_SIZE, "%d\n", ina226_avg_tab[INA226_READ_AVG(data->regs[INA2XX_CONFIG])]);
would accomplish exactly the same.
Quoted 44 lines
drivers/hwmon/ina2xx.c +40
-0+ } + +return snprintf (buf,PAGE_SIZE ,"%d\n" , ina226_avg_tab[i]); +} + +static ssize_t ina226_set_avg (struct device *dev, +struct device_attribute *da, +const char *buf,size_t count) +{ +struct ina2xx_data *data =dev_get_drvdata (dev); +unsigned long val; +int status, avg; + +if (IS_ERR (data)) +return PTR_ERR (data); + + status =kstrtoul (buf,10 , &val); +if (status <0 ) +return status; + +if (val >INT_MAX || val =0 ) +return -EINVAL ; + + avg =ina226_avg_bits (val); + +mutex_lock (&data->update_lock); + data->curr_config = (data->regs[INA2XX_CONFIG ] & +INA226_AVG_WR_MASK ) | (avg <<9 ); + status =i2c_smbus_write_word_swapped (data->client, +INA2XX_CONFIG , + data->curr_config); +/* Make sure the next access re-reads all registers. */ + data->valid =0 ; +mutex_unlock (&data->update_lock); +if (status <0 ) +return status; + +return count; +} +/* shunt voltage */ static SENSOR_DEVICE_ATTR(in0_input, S_IRUGO, ina2xx_show_value, NULL, INA2XX_SHUNT_VOLTAGE);
drivers/hwmon/ina2xx.c static SENSOR_DEVICE_ATTR(shunt_resistor, S_IRUGO | S_IWUSR, · line 417
Quoted 5 lines
drivers/hwmon/ina2xx.c +2
-0@@ -313,6 +413,10 @@ static SENSOR_DEVICE_ATTR(shunt_resistor, S_IRUGO | S_IWUSR, ina2xx_show_value, ina2xx_set_shunt, INA2XX_CALIBRATION); +/* averaging rate */ +static SENSOR_DEVICE_ATTR(avg_rate, S_IRUGO | S_IWUSR,
I kind of dislike that attribute name. I don't have a better idea though, so I'll let it pass unless you have a better idea.
Quoted 47 lines
drivers/hwmon/ina2xx.c +17
-2+ ina226_show_avg, ina226_set_avg, 0); +/* pointers to created device attributes */ static struct attribute *ina2xx_attrs[] = { &sensor_dev_attr_in0_input.dev_attr.attr,@@ -322,7 +426,19 @@ static struct attribute *ina2xx_attrs[] = { &sensor_dev_attr_shunt_resistor.dev_attr.attr, NULL, }; -ATTRIBUTE_GROUPS (ina2xx); + +static const struct attribute_group ina2xx_group = { + .attrs = ina2xx_attrs, +}; + +static struct attribute *ina226_attrs[] = { + &sensor_dev_attr_avg_rate.dev_attr.attr, +NULL , +}; + +static const struct attribute_group ina226_group = { + .attrs = ina226_attrs, +};static int ina2xx_probe (struct i2c_client *client,const struct i2c_device_id *id)@@ -333,7 +449,7 @@ static int ina2xx_probe(struct i2c_client *client,struct ina2xx_data *data;struct device *hwmon_dev;u32 val; -int ret; +int ret, group =0 ;if (!i2c_check_functionality (adapter,I2C_FUNC_SMBUS_WORD_DATA ))return -ENODEV ;@@ -355,6 +471,7 @@ static int ina2xx_probe(struct i2c_client *client,/* set the device type */ data->kind = id->driver_data; data->config = &ina2xx_config[data->kind]; + data->curr_config = data->config->config_default; data->client = client; if (data->rshunt <= 0 ||@@ -369,8 +486,12 @@ static int ina2xx_probe(struct i2c_client *client,mutex_init (&data->update_lock);
drivers/hwmon/ina2xx.c static int ina2xx_probe(struct i2c_client *client, · line 497
Quoted 10 lines
drivers/hwmon/ina2xx.c +5
-1+ data->groups[group++] = &ina2xx_group; +if (data->kind = ina226) + data->groups[group++] = &ina226_group; + hwmon_dev =devm_hwmon_device_register_with_groups (dev, client->name, - data, ina2xx_groups); + data, data->groups);if (IS_ERR (hwmon_dev))return PTR_ERR (hwmon_dev);
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [v8, 5/5] hwmon: ina2xx: allow to change the averaging rate at run-time
2015-01-06 19:18 GMT+01:00 Guenter Roeck <[email protected]>:
Quoted 11 lines
ina226_avg_val()calculates the average value fromina226_avg_taband then you loop throughina226_avg_tabto find the index intoina226_avg_tabagain, only to use the thus calculated index for accessing ina226_avg_tab[] once more. Think about it. A simpleavg = ina226_avg_tab[INA226_READ_AVG(data->regs[INA2XX_CONFIG])]; return snprintf(buf, PAGE_SIZE, "%d\n", avg);or even
return snprintf(buf,PAGE_SIZE, "%d\n",
ina226_avg_tab[INA226_READ_AVG(data->regs[INA2XX_CONFIG])]);would accomplish exactly the same.
This was stupid, I admit. Fixed in the new version. Hope it's ok now.
Quoted 2 lines
I kind of dislike that attribute name. I don't have a better idea though, so I'll let it pass unless you have a better idea.
I don't really. What's wrong with this one?
Bart
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Guenter Roeck
maintainerQuoted 10 lines · Bartosz Golaszewski
This series implements a mechanism to detect if the chip is in its POR state and reinitialize it if needed. It also extends the sysfs interface to make the driver configurable at run-time.
The
shunt_resistorattribute allows to change the shunt resistance value at run-time in cases where ina2xx used to do the measurement isn't integrated with the shunt.The
avg_rateattribute allows to increase/decrease noise reduction.
Patches 1-4 added to -next; please don't resend. I'll do some testing before publishing it.
Comments to patch 5 sent out a minute ago.
Guenter
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors