Cortina Access Drivers Package 2
Subsystems (4)
v2 cover Cortina Access Drivers Package 2
This release adds the following drivers and
integrates support into the Cortina Access
Presidio Engineering Board:
CAxxxx SoC eMMC/SD controller
CAxxxx SoC I2C controller
CAxxxx Soc LED controller
CAxxxx SPI NAND and NOR controller
Changes in v2:
- Add I2C controller
- Add LED controller
- Add SPI NAND and NOR controller
Alex Nemirovsky (3):
board: presidio-asic: Add eMMC board support
board: presidio-asic: Add I2C support
board: presidio-asic: Add SPI NAND and NOR support
Arthur Li (2):
mmc: ca_dw_mmc: add DesignWare based DM support for CAxxxx SoCs
i2c: i2c-cortina: added CAxxxx I2C support
Jway Lin (2):
led: led_cortina: Add CAxxx LED support
board: presidio: add LED support
Pengpeng Chen (1):
spi: ca_sflash: Add CAxxxx SPI Flash Controller
MAINTAINERS | 10 + arch/arm/dts/ca-presidio-engboard.dts | 39 +- board/cortina/presidio-asic/presidio.c | 16 +- configs/cortina_presidio-asic-emmc_defconfig | 38 ++ configs/cortina_presidio-asic-spi-nand_defconfig | 48 ++ configs/cortina_presidio-asic-spi-nor_defconfig | 59 +++ drivers/i2c/Kconfig | 7 + drivers/i2c/Makefile | 1 + drivers/i2c/i2c-cortina.c | 346 ++++++++++++++ drivers/i2c/i2c-cortina.h | 92 ++++ drivers/led/Kconfig | 8 + drivers/led/Makefile | 1 + drivers/led/led_cortina.c | 308 ++++++++++++ drivers/mmc/Kconfig | 11 + drivers/mmc/Makefile | 1 + drivers/mmc/ca_dw_mmc.c | 181 +++++++ drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 + drivers/spi/ca_sflash.c | 575 +++++++++++++++++++++++ 19 files changed, 1744 insertions(+), 6 deletions(-) create mode 100644 configs/cortina_presidio-asic-emmc_defconfig create mode 100644 configs/cortina_presidio-asic-spi-nand_defconfig create mode 100644 configs/cortina_presidio-asic-spi-nor_defconfig create mode 100644 drivers/i2c/i2c-cortina.c create mode 100644 drivers/i2c/i2c-cortina.h create mode 100644 drivers/led/led_cortina.c create mode 100644 drivers/mmc/ca_dw_mmc.c create mode 100644 drivers/spi/ca_sflash.c
Signature · 1 line
2.7.4
PATCH v2 1/8 mmc: ca_dw_mmc: add DesignWare based DM support for CAxxxx SoCs
From: Arthur Li <[email protected]>
Initial DesignWare based DM support for Cortina Access CAxxxx SoCs.
---
Changes in v2:
- Add I2C controller
- Add LED controller
- Add SPI NAND and NOR controller
MAINTAINERS | 2 + drivers/mmc/Kconfig | 11 +++ drivers/mmc/Makefile | 1 + drivers/mmc/ca_dw_mmc.c | 181 ++++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 195 insertions(+) create mode 100644 drivers/mmc/ca_dw_mmc.c
MAINTAINERS +2 -0
@@ -180,6 +180,7 @@ F: board/cortina/common/ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c +F: drivers/mmc/ca_dw_mmc.c ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <[email protected]>
@@ -670,6 +671,7 @@ F: board/cortina/common/ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c +F: drivers/mmc/ca_dw_mmc.c MIPS MSCC M: Gregory CLEMENT <[email protected]>
drivers/mmc/Kconfig +11 -0
@@ -205,6 +205,17 @@ config MMC_DW block, this provides host support for SD and MMC interfaces, in both PIO, internal DMA mode and external DMA mode. +config MMC_DW_CORTINA + bool "Cortina specific extensions for Synopsys DW Memory Card Interface" + depends on DM_MMC + depends on MMC_DW + depends on BLK + default n + help + This selects support for Cortina SoC specific extensions to the + Synopsys DesignWare Memory Card Interface driver. Select this option + for platforms based on Cortina CAxxxx Soc's. + config MMC_DW_EXYNOS bool "Exynos specific extensions for Synopsys DW Memory Card Interface" depends on ARCH_EXYNOS
drivers/mmc/Makefile +1 -0
@@ -20,6 +20,7 @@ endif obj-$(CONFIG_ARM_PL180_MMCI) += arm_pl180_mmci.o obj-$(CONFIG_MMC_DAVINCI) += davinci_mmc.o obj-$(CONFIG_MMC_DW) += dw_mmc.o +obj-$(CONFIG_MMC_DW_CORTINA) += ca_dw_mmc.o obj-$(CONFIG_MMC_DW_EXYNOS) += exynos_dw_mmc.o obj-$(CONFIG_MMC_DW_K3) += hi6220_dw_mmc.o obj-$(CONFIG_MMC_DW_ROCKCHIP) += rockchip_dw_mmc.o
drivers/mmc/ca_dw_mmc.c new file +181 -0
181 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 2/8 board: presidio-asic: Add eMMC board support
In reply to Alex NemirovskyAdd initial eMMC support for Cortina Access Presidio Engineering Board
---
Changes in v2: None
configs/cortina_presidio-asic-emmc_defconfig | 33 ++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+) create mode 100644 configs/cortina_presidio-asic-emmc_defconfig
configs/cortina_presidio-asic-emmc_defconfig new file +33 -0
@@ -0,0 +1,33 @@ +CONFIG_ARM=y +# CONFIG_SYS_ARCH_TIMER is not set +CONFIG_TARGET_PRESIDIO_ASIC=y +CONFIG_SYS_TEXT_BASE=0x04000000 +CONFIG_ENV_SIZE=0x20000 +CONFIG_DM_GPIO=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_IDENT_STRING="Presidio-SoC" +CONFIG_SHOW_BOOT_PROGRESS=y +CONFIG_BOOTDELAY=3 +CONFIG_BOARD_EARLY_INIT_R=y +CONFIG_SYS_PROMPT="G3#" +CONFIG_CMD_MMC=y +CONFIG_CMD_PART=y +CONFIG_CMD_WDT=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIMER=y +CONFIG_CMD_SMC=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_OF_CONTROL=y +CONFIG_OF_LIVE=y +CONFIG_DEFAULT_DEVICE_TREE="ca-presidio-engboard" +# CONFIG_NET is not set +CONFIG_DM=y +CONFIG_CORTINA_GPIO=y +CONFIG_DM_MMC=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_CORTINA=y +CONFIG_DM_SERIAL=y +CONFIG_CORTINA_UART=y +CONFIG_WDT=y +CONFIG_WDT_CORTINA=y
Signature · 1 line
2.7.4
PATCH v2 3/8 i2c: i2c-cortina: added CAxxxx I2C support
In reply to Alex NemirovskyFrom: Arthur Li <[email protected]>
Add I2C controller support for Cortina Access CAxxxx SoCs
---
Changes in v2: None
MAINTAINERS | 4 + drivers/i2c/Kconfig | 7 + drivers/i2c/Makefile | 1 + drivers/i2c/i2c-cortina.c | 346 ++++++++++++++++++++++++++++++++++++++++++++++ drivers/i2c/i2c-cortina.h | 92 ++++++++++++ 5 files changed, 450 insertions(+) create mode 100644 drivers/i2c/i2c-cortina.c create mode 100644 drivers/i2c/i2c-cortina.h
MAINTAINERS +4 -0
@@ -181,6 +181,8 @@ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c F: drivers/mmc/ca_dw_mmc.c +F: drivers/i2c/i2c-cortina.c +F: drivers/i2c/i2c-cortina.h ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <[email protected]>
@@ -672,6 +674,8 @@ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c F: drivers/mmc/ca_dw_mmc.c +F: drivers/i2c/i2c-cortina.c +F: drivers/i2c/i2c-cortina.h MIPS MSCC M: Gregory CLEMENT <[email protected]>
drivers/i2c/Kconfig +7 -0
@@ -85,6 +85,13 @@ config SYS_I2C_CADENCE Say yes here to select Cadence I2C Host Controller. This controller is e.g. used by Xilinx Zynq. +config SYS_I2C_CA + tristate "Cortina-Access I2C Controller" + depends on DM_I2C && CORTINA_PLATFORM + default n + help + Say yes here to select Cortina-Access I2C Host Controller. + config SYS_I2C_DAVINCI bool "Davinci I2C Controller" depends on (ARCH_KEYSTONE || ARCH_DAVINCI)
drivers/i2c/Makefile +1 -0
@@ -12,6 +12,7 @@ obj-$(CONFIG_SYS_I2C) += i2c_core.o obj-$(CONFIG_SYS_I2C_ASPEED) += ast_i2c.o obj-$(CONFIG_SYS_I2C_AT91) += at91_i2c.o obj-$(CONFIG_SYS_I2C_CADENCE) += i2c-cdns.o +obj-$(CONFIG_SYS_I2C_CA) += i2c-cortina.o obj-$(CONFIG_SYS_I2C_DAVINCI) += davinci_i2c.o obj-$(CONFIG_SYS_I2C_DW) += designware_i2c.o ifdef CONFIG_DM_PCI
drivers/i2c/i2c-cortina.c new file +346 -0
346 lines not on this page · raw message
drivers/i2c/i2c-cortina.h new file +92 -0
92 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 4/8 board: presidio-asic: Add I2C support
In reply to Alex NemirovskyAdd I2C board support for Cortina Access Presidio Engineering Board
---
Changes in v2: None
configs/cortina_presidio-asic-emmc_defconfig | 3 +++ 1 file changed, 3 insertions(+)
configs/cortina_presidio-asic-emmc_defconfig +3 -0
@@ -10,6 +10,7 @@ CONFIG_SHOW_BOOT_PROGRESS=y CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_R=y CONFIG_SYS_PROMPT="G3#" +CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y CONFIG_CMD_PART=y CONFIG_CMD_WDT=y
@@ -24,6 +25,8 @@ CONFIG_DEFAULT_DEVICE_TREE="ca-presidio-engboard" # CONFIG_NET is not set CONFIG_DM=y CONFIG_CORTINA_GPIO=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_CA=y CONFIG_DM_MMC=y CONFIG_MMC_DW=y CONFIG_MMC_DW_CORTINA=y
Signature · 1 line
2.7.4
PATCH v2 5/8 led: led_cortina: Add CAxxx LED support
In reply to Alex NemirovskyFrom: Jway Lin <[email protected]>
Add Cortina Access LED controller support for CAxxxx SOCs
---
Changes in v2: None
MAINTAINERS | 2 + drivers/led/Kconfig | 8 ++ drivers/led/Makefile | 1 + drivers/led/led_cortina.c | 308 ++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 319 insertions(+) create mode 100644 drivers/led/led_cortina.c
MAINTAINERS +2 -0
@@ -183,6 +183,7 @@ F: drivers/serial/serial_cortina.c F: drivers/mmc/ca_dw_mmc.c F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h +F: drivers/led/led_cortina.c ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <[email protected]>
@@ -676,6 +677,7 @@ F: drivers/serial/serial_cortina.c F: drivers/mmc/ca_dw_mmc.c F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h +F: drivers/led/led_cortina.c MIPS MSCC M: Gregory CLEMENT <[email protected]>
drivers/led/Kconfig +8 -0
@@ -35,6 +35,14 @@ config LED_BCM6858 This option enables support for LEDs connected to the BCM6858 HW has blinking capabilities and up to 32 LEDs can be controlled. +config LED_CORTINA + bool "LED Support for Cortina Access CAxxxx SoCs" + depends on LED && (CORTINA_PLATFORM) + help + This option enables support for LEDs connected to the Cortina + Access CAxxxx SOCs. + + config LED_BLINK bool "Support LED blinking" depends on LED
drivers/led/Makefile +1 -0
@@ -8,3 +8,4 @@ obj-$(CONFIG_LED_BCM6328) += led_bcm6328.o obj-$(CONFIG_LED_BCM6358) += led_bcm6358.o obj-$(CONFIG_LED_BCM6858) += led_bcm6858.o obj-$(CONFIG_$(SPL_)LED_GPIO) += led_gpio.o +obj-$(CONFIG_LED_CORTINA) += led_cortina.o
drivers/led/led_cortina.c new file +308 -0
308 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 6/8 board: presidio: add LED support
In reply to Alex NemirovskyFrom: Jway Lin <[email protected]>
Add LED support for Cortina Access Presidio Engineering Board
---
Changes in v2: None
arch/arm/dts/ca-presidio-engboard.dts | 31 ++++++++++++++++++++++++++++ configs/cortina_presidio-asic-emmc_defconfig | 2 ++ 2 files changed, 33 insertions(+)
arch/arm/dts/ca-presidio-engboard.dts +31 -0
@@ -66,4 +66,35 @@ spi-max-frequency = <108000000>; }; }; + + leds: led-controller at f43200f0 { + compatible = "cortina,ca-leds"; + reg = <0x0 0xf43200f0 0x40>; + + cortina,blink_rate1 = <256>; + cortina,blink_rate2 = <512>; + + led at 0 { + pin = <0>; + active-low; + blink-sel =<0>; + port = <0>; + off-event = <0>; + label = "led0"; + }; + + led at 1 { + pin = <1>; + active-low; + blink-sel =<1>; + label = "led1"; + }; + + led at 2 { + pin = <2>; + active-low; + label = "led2"; + }; + + }; };
configs/cortina_presidio-asic-emmc_defconfig +2 -0
@@ -27,6 +27,8 @@ CONFIG_DM=y CONFIG_CORTINA_GPIO=y CONFIG_DM_I2C=y CONFIG_SYS_I2C_CA=y +CONFIG_LED=y +CONFIG_LED_CORTINA=y CONFIG_DM_MMC=y CONFIG_MMC_DW=y CONFIG_MMC_DW_CORTINA=y
Signature · 1 line
2.7.4
PATCH v2 7/8 spi: ca_sflash: Add CAxxxx SPI Flash Controller
In reply to Alex NemirovskyFrom: Pengpeng Chen <[email protected]>
Add SPI Flash controller driver for Cortina Access CAxxxx SoCs
---
Changes in v2: None
MAINTAINERS | 2 + drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 + drivers/spi/ca_sflash.c | 575 ++++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 586 insertions(+) create mode 100644 drivers/spi/ca_sflash.c
MAINTAINERS +2 -0
@@ -184,6 +184,7 @@ F: drivers/mmc/ca_dw_mmc.c F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h F: drivers/led/led_cortina.c +F: drivers/spi/ca_sflash.c ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <[email protected]>
@@ -678,6 +679,7 @@ F: drivers/mmc/ca_dw_mmc.c F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h F: drivers/led/led_cortina.c +F: drivers/spi/ca_sflash.c MIPS MSCC M: Gregory CLEMENT <[email protected]>
drivers/spi/Kconfig +8 -0
@@ -106,6 +106,14 @@ config BCMSTB_SPI be used to access the SPI flash on platforms embedding this Broadcom SPI core. +config CORTINA_SFLASH + bool "Cortina-Access Serial Flash controller driver" + depends on DM_SPI && SPI_MEM + help + Enable the Cortina-Access Serial Flash controller driver. This driver + can be used to access the SPI NOR/NAND flash on platforms embedding this + Cortina-Access IP core. + config CADENCE_QSPI bool "Cadence QSPI driver" help
drivers/spi/Makefile +1 -0
@@ -25,6 +25,7 @@ obj-$(CONFIG_BCM63XX_SPI) += bcm63xx_spi.o obj-$(CONFIG_BCMSTB_SPI) += bcmstb_spi.o obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o obj-$(CONFIG_CF_SPI) += cf_spi.o +obj-$(CONFIG_CORTINA_SFLASH) += ca_sflash.o obj-$(CONFIG_DAVINCI_SPI) += davinci_spi.o obj-$(CONFIG_DESIGNWARE_SPI) += designware_spi.o obj-$(CONFIG_EXYNOS_SPI) += exynos_spi.o
drivers/spi/ca_sflash.c new file +575 -0
575 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 8/8 board: presidio-asic: Add SPI NAND and NOR support
In reply to Alex NemirovskyAdd SPI NAND and NOR support for Cortina Access
Presidio Engineering Board
---
Changes in v2: None
arch/arm/dts/ca-presidio-engboard.dts | 8 ++-- board/cortina/presidio-asic/presidio.c | 16 ++++++- configs/cortina_presidio-asic-spi-nand_defconfig | 48 +++++++++++++++++++ configs/cortina_presidio-asic-spi-nor_defconfig | 59 ++++++++++++++++++++++++ 4 files changed, 125 insertions(+), 6 deletions(-) create mode 100644 configs/cortina_presidio-asic-spi-nand_defconfig create mode 100644 configs/cortina_presidio-asic-spi-nor_defconfig
arch/arm/dts/ca-presidio-engboard.dts +3 -5
@@ -55,15 +55,13 @@ }; sflash: sflash-controller at f4324000 { - #address-cells = <2>; - #size-cells = <1>; compatible = "cortina,ca-sflash"; reg = <0x0 0xf4324000 0x50>; reg-names = "sflash-regs"; flash at 0 { - compatible = "jedec,spi-nor"; - spi-rx-bus-width = <1>; - spi-max-frequency = <108000000>; + compatible = "spi-nand", "jedec,spi-nor"; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <4>; }; };
board/cortina/presidio-asic/presidio.c +15 -1
@@ -14,7 +14,7 @@#include <asm/psci.h> #include <cpu_func.h> #include <asm/armv8/mmu.h> - +#include <dm/uclass.h> DECLARE_GLOBAL_DATA_PTR ;#define CA_PERIPH_BASE 0xE0000000UL
@@ -70,9 +70,23 @@ static noinline int invoke_psci_fn_smc(u64 function_id, u64 arg0, u64 arg1,return function_id; } +#ifdef CONFIG_CORTINA_SFLASH +static int init_sflash (void ) +{ +struct udevice *dev; + +uclass_first_device (UCLASS_SPI , &dev); + +return 0 ; +} +#endif +int board_early_init_r (void ) {dcache_disable (); +#ifdef CONFIG_CORTINA_SFLASH +init_sflash (); +#endif return 0 ; }
configs/cortina_presidio-asic-spi-nand_defconfig new file +48 -0
48 lines not on this page · raw message
configs/cortina_presidio-asic-spi-nor_defconfig new file +59 -0
59 lines not on this page · raw message
Signature · 1 line
2.7.4
v2 cover Cortina Access Drivers Package 2
In reply to Alex NemirovskyHi Tom,
Are we still blocked on this set until the upcoming 2020.4 release?
Quoted 65 lines · Alex Nemirovsky
This release adds the following drivers and
integrates support into the Cortina Access
Presidio Engineering Board:CAxxxx SoC eMMC/SD controller
CAxxxx SoC I2C controller
CAxxxx Soc LED controller
CAxxxx SPI NAND and NOR controllerChanges in v2:
- Add I2C controller
- Add LED controller
- Add SPI NAND and NOR controllerAlex Nemirovsky (3):
board: presidio-asic: Add eMMC board support
board: presidio-asic: Add I2C support
board: presidio-asic: Add SPI NAND and NOR supportArthur Li (2):
mmc:ca_dw_mmc: add DesignWare based DM support for CAxxxx SoCs
i2c: i2c-cortina: added CAxxxx I2C supportJway Lin (2):
led:led_cortina: Add CAxxx LED support
board: presidio: add LED supportPengpeng Chen (1):
spi:ca_sflash: Add CAxxxx SPI Flash ControllerMAINTAINERS | 10 + arch/arm/dts/ca-presidio-engboard.dts | 39 +- board/cortina/presidio-asic/presidio.c | 16 +- configs/cortina_presidio-asic-emmc_defconfig | 38 ++ configs/cortina_presidio-asic-spi-nand_defconfig | 48 ++ configs/cortina_presidio-asic-spi-nor_defconfig | 59 +++ drivers/i2c/Kconfig | 7 + drivers/i2c/Makefile | 1 + drivers/i2c/i2c-cortina.c | 346 ++++++++++++++ drivers/i2c/i2c-cortina.h | 92 ++++ drivers/led/Kconfig | 8 + drivers/led/Makefile | 1 + drivers/led/led_cortina.c | 308 ++++++++++++ drivers/mmc/Kconfig | 11 + drivers/mmc/Makefile | 1 + drivers/mmc/ca_dw_mmc.c | 181 +++++++ drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 + drivers/spi/ca_sflash.c | 575 +++++++++++++++++++++++ 19 files changed, 1744 insertions(+), 6 deletions(-)create mode 100644 configs/cortina_presidio-asic-emmc_defconfig create mode 100644 configs/cortina_presidio-asic-spi-nand_defconfig create mode 100644 configs/cortina_presidio-asic-spi-nor_defconfig create mode 100644
drivers/i2c/i2c-cortina.c
create mode 100644drivers/i2c/i2c-cortina.h
create mode 100644drivers/led/led_cortina.c
create mode 100644drivers/mmc/ca_dw_mmc.c
create mode 100644drivers/spi/ca_sflash.cSignature · 1 line
2.7.4
v2 cover Cortina Access Drivers Package 2
Hi Alex,
you should always CC the maintainers of the affected sub-systems or architecture. Otherwise it's random if a maintainer reads through the list and discovers your patches ;)
You can find out with get_maintainers.pl like this:
$ ./scripts/get_maintainer.pl drivers/i2c/ Heiko Schocher <[email protected]> (maintainer:I2C) u-boot at lists.denx.de (open list)
Am 19.03.20 um 01:16 schrieb Alex Nemirovsky:
Quoted 69 lines
Hi Tom,
Are we still blocked on this set until the upcoming 2020.4 release?Quoted 65 lines · Alex Nemirovsky
This release adds the following drivers and
integrates support into the Cortina Access
Presidio Engineering Board:CAxxxx SoC eMMC/SD controller
CAxxxx SoC I2C controller
CAxxxx Soc LED controller
CAxxxx SPI NAND and NOR controllerChanges in v2:
- Add I2C controller
- Add LED controller
- Add SPI NAND and NOR controllerAlex Nemirovsky (3):
board: presidio-asic: Add eMMC board support
board: presidio-asic: Add I2C support
board: presidio-asic: Add SPI NAND and NOR supportArthur Li (2):
mmc:ca_dw_mmc: add DesignWare based DM support for CAxxxx SoCs
i2c: i2c-cortina: added CAxxxx I2C supportJway Lin (2):
led:led_cortina: Add CAxxx LED support
board: presidio: add LED supportPengpeng Chen (1):
spi:ca_sflash: Add CAxxxx SPI Flash ControllerMAINTAINERS | 10 + arch/arm/dts/ca-presidio-engboard.dts | 39 +- board/cortina/presidio-asic/presidio.c | 16 +- configs/cortina_presidio-asic-emmc_defconfig | 38 ++ configs/cortina_presidio-asic-spi-nand_defconfig | 48 ++ configs/cortina_presidio-asic-spi-nor_defconfig | 59 +++ drivers/i2c/Kconfig | 7 + drivers/i2c/Makefile | 1 + drivers/i2c/i2c-cortina.c | 346 ++++++++++++++ drivers/i2c/i2c-cortina.h | 92 ++++ drivers/led/Kconfig | 8 + drivers/led/Makefile | 1 + drivers/led/led_cortina.c | 308 ++++++++++++ drivers/mmc/Kconfig | 11 + drivers/mmc/Makefile | 1 + drivers/mmc/ca_dw_mmc.c | 181 +++++++ drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 + drivers/spi/ca_sflash.c | 575 +++++++++++++++++++++++ 19 files changed, 1744 insertions(+), 6 deletions(-)create mode 100644 configs/cortina_presidio-asic-emmc_defconfig create mode 100644 configs/cortina_presidio-asic-spi-nand_defconfig create mode 100644 configs/cortina_presidio-asic-spi-nor_defconfig create mode 100644
drivers/i2c/i2c-cortina.c
create mode 100644drivers/i2c/i2c-cortina.h
create mode 100644drivers/led/led_cortina.c
create mode 100644drivers/mmc/ca_dw_mmc.c
create mode 100644drivers/spi/ca_sflash.cSignature · 1 line
2.7.4
Signature · 1 line
- Daniel