Cortina Access Drivers Package 2
Subsystems (4)
v2 cover Cortina Access Drivers Package 2
This release adds the following drivers and
integrates support into the Cortina Access
Presidio Engineering Board:
CAxxxx SoC eMMC/SD controller
CAxxxx SoC I2C controller
CAxxxx Soc LED controller
CAxxxx SPI NAND and NOR controller
Changes in v3:
- Fixup syntax issues related to checkpatch.pl cleanup
Changes in v2:
- Add I2C controller
- Add LED controller
- Add SPI NAND and NOR controller
Alex Nemirovsky (3):
board: presidio-asic: Add eMMC board support
board: presidio-asic: Add I2C support
board: presidio-asic: Add SPI NAND and NOR support
Arthur Li (2):
mmc: ca_dw_mmc: add DesignWare based DM support for CAxxxx SoCs
i2c: i2c-cortina: added CAxxxx I2C support
Jway Lin (2):
led: led_cortina: Add CAxxx LED support
board: presidio: add LED support
Pengpeng Chen (1):
spi: ca_sflash: Add CAxxxx SPI Flash Controller
MAINTAINERS | 10 + arch/arm/dts/ca-presidio-engboard.dts | 39 +- board/cortina/presidio-asic/presidio.c | 16 +- configs/cortina_presidio-asic-emmc_defconfig | 38 ++ configs/cortina_presidio-asic-spi-nand_defconfig | 48 ++ configs/cortina_presidio-asic-spi-nor_defconfig | 59 +++ drivers/i2c/Kconfig | 7 + drivers/i2c/Makefile | 1 + drivers/i2c/i2c-cortina.c | 346 ++++++++++++++ drivers/i2c/i2c-cortina.h | 92 ++++ drivers/led/Kconfig | 8 + drivers/led/Makefile | 1 + drivers/led/led_cortina.c | 308 ++++++++++++ drivers/mmc/Kconfig | 11 + drivers/mmc/Makefile | 1 + drivers/mmc/ca_dw_mmc.c | 181 +++++++ drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 + drivers/spi/ca_sflash.c | 576 +++++++++++++++++++++++ 19 files changed, 1745 insertions(+), 6 deletions(-) create mode 100644 configs/cortina_presidio-asic-emmc_defconfig create mode 100644 configs/cortina_presidio-asic-spi-nand_defconfig create mode 100644 configs/cortina_presidio-asic-spi-nor_defconfig create mode 100644 drivers/i2c/i2c-cortina.c create mode 100644 drivers/i2c/i2c-cortina.h create mode 100644 drivers/led/led_cortina.c create mode 100644 drivers/mmc/ca_dw_mmc.c create mode 100644 drivers/spi/ca_sflash.c
Signature · 1 line
2.7.4
PATCH v2 1/8 mmc: ca_dw_mmc: add DesignWare based DM support for CAxxxx SoCs
From: Arthur Li <[email protected]>
Initial DesignWare based DM support for Cortina Access CAxxxx SoCs.
---
Changes in v3: None
Changes in v2:
- Add I2C controller
- Add LED controller
- Add SPI NAND and NOR controller
MAINTAINERS | 2 + drivers/mmc/Kconfig | 11 +++ drivers/mmc/Makefile | 1 + drivers/mmc/ca_dw_mmc.c | 181 ++++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 195 insertions(+) create mode 100644 drivers/mmc/ca_dw_mmc.c
MAINTAINERS +2 -0
@@ -180,6 +180,7 @@ F: board/cortina/common/ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c +F: drivers/mmc/ca_dw_mmc.c ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <[email protected]>
@@ -670,6 +671,7 @@ F: board/cortina/common/ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c +F: drivers/mmc/ca_dw_mmc.c MIPS MSCC M: Gregory CLEMENT <[email protected]>
drivers/mmc/Kconfig +11 -0
@@ -205,6 +205,17 @@ config MMC_DW block, this provides host support for SD and MMC interfaces, in both PIO, internal DMA mode and external DMA mode. +config MMC_DW_CORTINA + bool "Cortina specific extensions for Synopsys DW Memory Card Interface" + depends on DM_MMC + depends on MMC_DW + depends on BLK + default n + help + This selects support for Cortina SoC specific extensions to the + Synopsys DesignWare Memory Card Interface driver. Select this option + for platforms based on Cortina CAxxxx Soc's. + config MMC_DW_EXYNOS bool "Exynos specific extensions for Synopsys DW Memory Card Interface" depends on ARCH_EXYNOS
drivers/mmc/Makefile +1 -0
@@ -20,6 +20,7 @@ endif obj-$(CONFIG_ARM_PL180_MMCI) += arm_pl180_mmci.o obj-$(CONFIG_MMC_DAVINCI) += davinci_mmc.o obj-$(CONFIG_MMC_DW) += dw_mmc.o +obj-$(CONFIG_MMC_DW_CORTINA) += ca_dw_mmc.o obj-$(CONFIG_MMC_DW_EXYNOS) += exynos_dw_mmc.o obj-$(CONFIG_MMC_DW_K3) += hi6220_dw_mmc.o obj-$(CONFIG_MMC_DW_ROCKCHIP) += rockchip_dw_mmc.o
drivers/mmc/ca_dw_mmc.c new file +181 -0
181 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 1/8 mmc: ca_dw_mmc: add DesignWare based DM support for CAxxxx SoCs
Quoted 118 lines · Alex Nemirovsky
From: Arthur Li <[email protected]>
Initial DesignWare based DM support for Cortina Access CAxxxx SoCs.
Signed-off-by Arthur Li <[email protected]>Signed-off-by Alex Nemirovsky <[email protected]>---
Changes in v3: None
Changes in v2:
- Add I2C controller
- Add LED controller
- Add SPI NAND and NOR controllerMAINTAINERS | 2 + drivers/mmc/Kconfig | 11 +++ drivers/mmc/Makefile | 1 + drivers/mmc/ca_dw_mmc.c | 181 ++++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 195 insertions(+) create mode 100644 drivers/mmc/ca_dw_mmc.cMAINTAINERS +2
-0@@ -180,6 +180,7 @@ F: board/cortina/common/ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c +F: drivers/mmc/ca_dw_mmc.c ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <[email protected]>@@ -670,6 +671,7 @@ F: board/cortina/common/ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c +F: drivers/mmc/ca_dw_mmc.c MIPS MSCC M: Gregory CLEMENT <[email protected]>drivers/mmc/Kconfig +11
-0@@ -205,6 +205,17 @@ config MMC_DW block, this provides host support for SD and MMC interfaces, in both PIO, internal DMA mode and external DMA mode. +config MMC_DW_CORTINA + bool "Cortina specific extensions for Synopsys DW Memory Card Interface" + depends on DM_MMC + depends on MMC_DW + depends on BLK + default n + help + This selects support for Cortina SoC specific extensions to the + Synopsys DesignWare Memory Card Interface driver. Select this option + for platforms based on Cortina CAxxxx Soc's. + config MMC_DW_EXYNOS bool "Exynos specific extensions for Synopsys DW Memory Card Interface" depends on ARCH_EXYNOSdrivers/mmc/Makefile +1
-0@@ -20,6 +20,7 @@ endif obj-$(CONFIG_ARM_PL180_MMCI) += arm_pl180_mmci.o obj-$(CONFIG_MMC_DAVINCI) += davinci_mmc.o obj-$(CONFIG_MMC_DW) += dw_mmc.o +obj-$(CONFIG_MMC_DW_CORTINA) += ca_dw_mmc.o obj-$(CONFIG_MMC_DW_EXYNOS) += exynos_dw_mmc.o obj-$(CONFIG_MMC_DW_K3) += hi6220_dw_mmc.o obj-$(CONFIG_MMC_DW_ROCKCHIP) += rockchip_dw_mmc.odrivers/mmc/ca_dw_mmc.c new file +36
-0@@ -0,0 +1,181 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* (C) Copyright 2019 Cortina Access +* Arthur Li <[email protected]> +*/ + +#include <common.h> +#include <dwmmc.h> +#include <fdtdec.h> +#include <linux/libfdt.h> +#include <malloc.h> +#include <errno.h> +#include <dm.h> +#include <mapmem.h> + +#define SD_CLK_SEL_MASK (0x3) +#define SD_DLL_DEFAULT (0x143000) +#define SD_SCLK_MAX (200000000) + +#define SD_CLK_SEL_200MHZ (0x2) +#define SD_CLK_SEL_100MHZ (0x1) + +#define IO_DRV_SD_DS_OFFSET (16) +#define IO_DRV_SD_DS_MASK (0xff << IO_DRV_SD_DS_OFFSET) + +#define MIN_FREQ (400000) + +DECLARE_GLOBAL_DATA_PTR ; + +struct ca_mmc_plat { +struct mmc_config cfg; +struct mmc mmc; +}; + +struct ca_dwmmc_priv_data { +struct dwmci_host host;
drivers/mmc/ca_dw_mmc.c line 46
Quoted 10 lines
drivers/mmc/ca_dw_mmc.c new file +10
-0+void __iomem *sd_dll_reg; +void __iomem *io_drv_reg; +u8 ds; +}; + +static void ca_dwmci_clksel (struct dwmci_host *host) +{ +struct ca_dwmmc_priv_data *priv = host->priv; +u32 val =readl (priv->sd_dll_reg); +
How about below?
val &= ~SD_CLK_SEL_MASK;
if (..) {
val |= ..
} else if (...) {
val |= ...
}Quoted 48 lines
drivers/mmc/ca_dw_mmc.c new file +48
-0+if (host->bus_hz >=200000000 ) { + val &= ~SD_CLK_SEL_MASK ; + val |=SD_CLK_SEL_200MHZ ; + }else if (host->bus_hz >=100000000 ) { + val &= ~SD_CLK_SEL_MASK ; + val |=SD_CLK_SEL_100MHZ ; + }else { + val &= ~SD_CLK_SEL_MASK ; + } + +writel (val, priv->sd_dll_reg); +} + +static void ca_dwmci_board_init (struct dwmci_host *host) +{ +struct ca_dwmmc_priv_data *priv = host->priv; +u32 val =readl (priv->io_drv_reg); + +writel (SD_DLL_DEFAULT , priv->sd_dll_reg); + + val &= ~IO_DRV_SD_DS_MASK ; +if (priv && priv->ds) + val |= priv->ds <<IO_DRV_SD_DS_OFFSET ; +writel (val, priv->io_drv_reg); +} + +unsigned int ca_dwmci_get_mmc_clock (struct dwmci_host *host,uint freq) +{ +struct ca_dwmmc_priv_data *priv = host->priv; +u8 sd_clk_sel =readl (priv->sd_dll_reg) &SD_CLK_SEL_MASK ; +u8 clk_div; + +switch (sd_clk_sel) { +case 2 : + clk_div =1 ; +break ; +case 1 : + clk_div =2 ; +break ; +default : + clk_div =4 ; + } + +return SD_SCLK_MAX / clk_div / (host->div +1 ); +} + +static int ca_dwmmc_ofdata_to_platdata (struct udevice *dev) +{
drivers/mmc/ca_dw_mmc.c line 104
Quoted 10 lines
drivers/mmc/ca_dw_mmc.c new file +10
-0+struct ca_dwmmc_priv_data *priv =dev_get_priv (dev); +struct dwmci_host *host = &priv->host; +u32 tmp; + + host->name = dev->name; + host->dev_index =0 ; + + host->buswidth =dev_read_u32_default (dev,"bus-width" ,1 ); +if (host->buswidth !=1 && host->buswidth !=4 ) +return -EINVAL ;
It doesn't support 8bit buswidth?
Quoted 31 lines
drivers/mmc/ca_dw_mmc.c new file +31
-0+ + host->bus_hz =dev_read_u32_default (dev,"max-frequency" ,50000000 ); + priv->ds =dev_read_u32_default (dev,"io_ds" ,0x33 ); + host->fifo_mode =dev_read_bool (dev,"fifo-mode" ); + +dev_read_u32 (dev,"sd_dll_ctrl" , &tmp); + priv->sd_dll_reg =map_sysmem ((uintptr_t )tmp,sizeof (uintptr_t )); +if (!priv->sd_dll_reg) +return -EINVAL ; + +dev_read_u32 (dev,"io_drv_ctrl" , &tmp); + priv->io_drv_reg =map_sysmem ((uintptr_t )tmp,sizeof (uintptr_t )); +if (!priv->io_drv_reg) +return -EINVAL ; + + host->ioaddr =dev_read_addr_ptr (dev); +if (host->ioaddr == (void *)FDT_ADDR_T_NONE ) { +printf ("DWMMC: base address is invalid\n" ); +return -EINVAL ; + } + + host->priv = priv; + +return 0 ; +} + +struct dm_mmc_ops ca_dwmci_dm_ops; + +static int ca_dwmmc_probe (struct udevice *dev) +{ +struct ca_mmc_plat *plat =dev_get_platdata (dev);
drivers/mmc/ca_dw_mmc.c line 145
Quoted 10 lines
drivers/mmc/ca_dw_mmc.c new file +10
-0+struct mmc_uclass_priv *upriv =dev_get_uclass_priv (dev); +struct ca_dwmmc_priv_data *priv =dev_get_priv (dev); +struct dwmci_host *host = &priv->host; + +memcpy (&ca_dwmci_dm_ops, &dm_dwmci_ops,sizeof (struct dm_mmc_ops )); + +dwmci_setup_cfg (&plat->cfg, host, host->bus_hz,MIN_FREQ ); +if (host->buswidth ==1 ) { + (&plat->cfg)->host_caps &= ~MMC_MODE_8BIT ; + (&plat->cfg)->host_caps &= ~MMC_MODE_4BIT ;
host->caps &= ~(MMC_MODE_8BIT | MMC_MODE_4BIT);
Quoted 37 lines
drivers/mmc/ca_dw_mmc.c new file +36
-0+ } + + host->mmc = &plat->mmc; + host->mmc->priv = &priv->host; + upriv->mmc = host->mmc; + host->mmc->dev = dev; + host->clksel = ca_dwmci_clksel; + host->board_init = ca_dwmci_board_init; + host->get_mmc_clk = ca_dwmci_get_mmc_clock; + +return dwmci_probe (dev); +} + +static int ca_dwmmc_bind (struct udevice *dev) +{ +struct ca_mmc_plat *plat =dev_get_platdata (dev); + +return dwmci_bind (dev, &plat->mmc, &plat->cfg); +} + +static const struct udevice_id ca_dwmmc_ids[] = { + { .compatible ="snps,dw-cortina" }, + { } +}; + +U_BOOT_DRIVER (ca_dwmmc_drv) = { + .name ="cortina_dwmmc" , + .id =UCLASS_MMC , + .of_match = ca_dwmmc_ids, + .ofdata_to_platdata = ca_dwmmc_ofdata_to_platdata, + .bind = ca_dwmmc_bind, + .ops = &ca_dwmci_dm_ops, + .probe = ca_dwmmc_probe, + .priv_auto_alloc_size =sizeof (struct ca_dwmmc_priv_data ), + .platdata_auto_alloc_size =sizeof (struct ca_mmc_plat ), +};
PATCH v2 1/8 mmc: ca_dw_mmc: add DesignWare based DM support for CAxxxx SoCs
Hi Arthur,
could you respond to this or fix as required?
Thanks
Alex
Quoted 285 lines · Jaehoon Chung
Quoted 118 lines · Alex Nemirovsky
From: Arthur Li <[email protected]>
Initial DesignWare based DM support for Cortina Access CAxxxx SoCs.
Signed-off-by Arthur Li <[email protected]>Signed-off-by Alex Nemirovsky <[email protected]>---
Changes in v3: None
Changes in v2:
- Add I2C controller
- Add LED controller
- Add SPI NAND and NOR controllerMAINTAINERS | 2 + drivers/mmc/Kconfig | 11 +++ drivers/mmc/Makefile | 1 + drivers/mmc/ca_dw_mmc.c | 181 ++++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 195 insertions(+)create mode 100644
drivers/mmc/ca_dw_mmc.cMAINTAINERS +0
-0@@ -180,6 +180,7 @@ F: board/cortina/common/F:
drivers/gpio/cortina_gpio.c
F:drivers/watchdog/cortina_wdt.c
F:drivers/serial/serial_cortina.c
+F:drivers/mmc/ca_dw_mmc.cARM/CZ.NIC TURRIS MOX SUPPORT
M: Marek Behun <[email protected]>MAINTAINERS +0
-0@@ -670,6 +671,7 @@ F: board/cortina/common/F:
drivers/gpio/cortina_gpio.c
F:drivers/watchdog/cortina_wdt.c
F:drivers/serial/serial_cortina.c
+F:drivers/mmc/ca_dw_mmc.cMIPS MSCC
M: Gregory CLEMENT <[email protected]>drivers/mmc/Kconfig +11
-0@@ -205,6 +205,17 @@ config MMC_DW block, this provides host support for SD and MMC interfaces, in both PIO, internal DMA mode and external DMA mode. +config MMC_DW_CORTINA + bool "Cortina specific extensions for Synopsys DW Memory Card Interface" + depends on DM_MMC + depends on MMC_DW + depends on BLK + default n + help + This selects support for Cortina SoC specific extensions to the + Synopsys DesignWare Memory Card Interface driver. Select this option + for platforms based on Cortina CAxxxx Soc's. +config
MMC_DW_EXYNOS
bool "Exynos specific extensions for Synopsys DW Memory Card Interface" depends onARCH_EXYNOSdrivers/mmc/Makefile +0
-0@@ -20,6 +20,7 @@ endifobj-$(CONFIG_ARM_PL180_MMCI) += arm_pl180_mmci.o
obj-$(CONFIG_MMC_DAVINCI) += davinci_mmc.o
obj-$(CONFIG_MMC_DW) += dw_mmc.o
+obj-$(CONFIG_MMC_DW_CORTINA) += ca_dw_mmc.o
obj-$(CONFIG_MMC_DW_EXYNOS) += exynos_dw_mmc.o
obj-$(CONFIG_MMC_DW_K3) += hi6220_dw_mmc.o
obj-$(CONFIG_MMC_DW_ROCKCHIP) += rockchip_dw_mmc.odrivers/mmc/ca_dw_mmc.c new file +36
-0@@ -0,0 +1,181 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* (C) Copyright 2019 Cortina Access +* Arthur Li <[email protected]> +*/ + +#include <common.h> +#include <dwmmc.h> +#include <fdtdec.h> +#include <linux/libfdt.h> +#include <malloc.h> +#include <errno.h> +#include <dm.h> +#include <mapmem.h> + +#define SD_CLK_SEL_MASK (0x3) +#define SD_DLL_DEFAULT (0x143000) +#define SD_SCLK_MAX (200000000) + +#define SD_CLK_SEL_200MHZ (0x2) +#define SD_CLK_SEL_100MHZ (0x1) + +#define IO_DRV_SD_DS_OFFSET (16) +#define IO_DRV_SD_DS_MASK (0xff << IO_DRV_SD_DS_OFFSET) + +#define MIN_FREQ (400000) + +DECLARE_GLOBAL_DATA_PTR ; + +struct ca_mmc_plat { +struct mmc_config cfg; +struct mmc mmc; +}; + +struct ca_dwmmc_priv_data { +struct dwmci_host host;drivers/mmc/ca_dw_mmc.c line 46
Quoted 10 lines
drivers/mmc/ca_dw_mmc.c new file +10
-0+void __iomem *sd_dll_reg; +void __iomem *io_drv_reg; +u8 ds; +}; + +static void ca_dwmci_clksel (struct dwmci_host *host) +{ +struct ca_dwmmc_priv_data *priv = host->priv; +u32 val =readl (priv->sd_dll_reg); +How about below?
val &= ~SD_CLK_SEL_MASK;
if (..) { val |= .. } else if (...) { val |= ... }Quoted 48 lines
drivers/mmc/ca_dw_mmc.c new file +48
-0+if (host->bus_hz >=200000000 ) { + val &= ~SD_CLK_SEL_MASK ; + val |=SD_CLK_SEL_200MHZ ; + }else if (host->bus_hz >=100000000 ) { + val &= ~SD_CLK_SEL_MASK ; + val |=SD_CLK_SEL_100MHZ ; + }else { + val &= ~SD_CLK_SEL_MASK ; + } + +writel (val, priv->sd_dll_reg); +} + +static void ca_dwmci_board_init (struct dwmci_host *host) +{ +struct ca_dwmmc_priv_data *priv = host->priv; +u32 val =readl (priv->io_drv_reg); + +writel (SD_DLL_DEFAULT , priv->sd_dll_reg); + + val &= ~IO_DRV_SD_DS_MASK ; +if (priv && priv->ds) + val |= priv->ds <<IO_DRV_SD_DS_OFFSET ; +writel (val, priv->io_drv_reg); +} + +unsigned int ca_dwmci_get_mmc_clock (struct dwmci_host *host,uint freq) +{ +struct ca_dwmmc_priv_data *priv = host->priv; +u8 sd_clk_sel =readl (priv->sd_dll_reg) &SD_CLK_SEL_MASK ; +u8 clk_div; + +switch (sd_clk_sel) { +case 2 : + clk_div =1 ; +break ; +case 1 : + clk_div =2 ; +break ; +default : + clk_div =4 ; + } + +return SD_SCLK_MAX / clk_div / (host->div +1 ); +} + +static int ca_dwmmc_ofdata_to_platdata (struct udevice *dev) +{drivers/mmc/ca_dw_mmc.c line 104
Quoted 10 lines
drivers/mmc/ca_dw_mmc.c new file +10
-0+struct ca_dwmmc_priv_data *priv =dev_get_priv (dev); +struct dwmci_host *host = &priv->host; +u32 tmp; + + host->name = dev->name; + host->dev_index =0 ; + + host->buswidth =dev_read_u32_default (dev,"bus-width" ,1 ); +if (host->buswidth !=1 && host->buswidth !=4 ) +return -EINVAL ;It doesn't support 8bit buswidth?
Quoted 31 lines
drivers/mmc/ca_dw_mmc.c new file +31
-0+ + host->bus_hz =dev_read_u32_default (dev,"max-frequency" ,50000000 ); + priv->ds =dev_read_u32_default (dev,"io_ds" ,0x33 ); + host->fifo_mode =dev_read_bool (dev,"fifo-mode" ); + +dev_read_u32 (dev,"sd_dll_ctrl" , &tmp); + priv->sd_dll_reg =map_sysmem ((uintptr_t )tmp,sizeof (uintptr_t )); +if (!priv->sd_dll_reg) +return -EINVAL ; + +dev_read_u32 (dev,"io_drv_ctrl" , &tmp); + priv->io_drv_reg =map_sysmem ((uintptr_t )tmp,sizeof (uintptr_t )); +if (!priv->io_drv_reg) +return -EINVAL ; + + host->ioaddr =dev_read_addr_ptr (dev); +if (host->ioaddr == (void *)FDT_ADDR_T_NONE ) { +printf ("DWMMC: base address is invalid\n" ); +return -EINVAL ; + } + + host->priv = priv; + +return 0 ; +} + +struct dm_mmc_ops ca_dwmci_dm_ops; + +static int ca_dwmmc_probe (struct udevice *dev) +{ +struct ca_mmc_plat *plat =dev_get_platdata (dev);drivers/mmc/ca_dw_mmc.c line 145
Quoted 10 lines
drivers/mmc/ca_dw_mmc.c new file +10
-0+struct mmc_uclass_priv *upriv =dev_get_uclass_priv (dev); +struct ca_dwmmc_priv_data *priv =dev_get_priv (dev); +struct dwmci_host *host = &priv->host; + +memcpy (&ca_dwmci_dm_ops, &dm_dwmci_ops,sizeof (struct dm_mmc_ops )); + +dwmci_setup_cfg (&plat->cfg, host, host->bus_hz,MIN_FREQ ); +if (host->buswidth ==1 ) { + (&plat->cfg)->host_caps &= ~MMC_MODE_8BIT ; + (&plat->cfg)->host_caps &= ~MMC_MODE_4BIT ;
host->caps&= ~(MMC_MODE_8BIT |MMC_MODE_4BIT);Quoted 37 lines
drivers/mmc/ca_dw_mmc.c new file +36
-0+ } + + host->mmc = &plat->mmc; + host->mmc->priv = &priv->host; + upriv->mmc = host->mmc; + host->mmc->dev = dev; + host->clksel = ca_dwmci_clksel; + host->board_init = ca_dwmci_board_init; + host->get_mmc_clk = ca_dwmci_get_mmc_clock; + +return dwmci_probe (dev); +} + +static int ca_dwmmc_bind (struct udevice *dev) +{ +struct ca_mmc_plat *plat =dev_get_platdata (dev); + +return dwmci_bind (dev, &plat->mmc, &plat->cfg); +} + +static const struct udevice_id ca_dwmmc_ids[] = { + { .compatible ="snps,dw-cortina" }, + { } +}; + +U_BOOT_DRIVER (ca_dwmmc_drv) = { + .name ="cortina_dwmmc" , + .id =UCLASS_MMC , + .of_match = ca_dwmmc_ids, + .ofdata_to_platdata = ca_dwmmc_ofdata_to_platdata, + .bind = ca_dwmmc_bind, + .ops = &ca_dwmci_dm_ops, + .probe = ca_dwmmc_probe, + .priv_auto_alloc_size =sizeof (struct ca_dwmmc_priv_data ), + .platdata_auto_alloc_size =sizeof (struct ca_mmc_plat ), +};
PATCH v2 2/8 board: presidio-asic: Add eMMC board support
In reply to Alex NemirovskyAdd initial eMMC support for Cortina Access Presidio Engineering Board
---
Changes in v3: None
Changes in v2: None
configs/cortina_presidio-asic-emmc_defconfig | 33 ++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+) create mode 100644 configs/cortina_presidio-asic-emmc_defconfig
configs/cortina_presidio-asic-emmc_defconfig new file +33 -0
@@ -0,0 +1,33 @@ +CONFIG_ARM=y +# CONFIG_SYS_ARCH_TIMER is not set +CONFIG_TARGET_PRESIDIO_ASIC=y +CONFIG_SYS_TEXT_BASE=0x04000000 +CONFIG_ENV_SIZE=0x20000 +CONFIG_DM_GPIO=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_IDENT_STRING="Presidio-SoC" +CONFIG_SHOW_BOOT_PROGRESS=y +CONFIG_BOOTDELAY=3 +CONFIG_BOARD_EARLY_INIT_R=y +CONFIG_SYS_PROMPT="G3#" +CONFIG_CMD_MMC=y +CONFIG_CMD_PART=y +CONFIG_CMD_WDT=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIMER=y +CONFIG_CMD_SMC=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_OF_CONTROL=y +CONFIG_OF_LIVE=y +CONFIG_DEFAULT_DEVICE_TREE="ca-presidio-engboard" +# CONFIG_NET is not set +CONFIG_DM=y +CONFIG_CORTINA_GPIO=y +CONFIG_DM_MMC=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_CORTINA=y +CONFIG_DM_SERIAL=y +CONFIG_CORTINA_UART=y +CONFIG_WDT=y +CONFIG_WDT_CORTINA=y
Signature · 1 line
2.7.4
PATCH v2 3/8 i2c: i2c-cortina: added CAxxxx I2C support
In reply to Alex NemirovskyFrom: Arthur Li <[email protected]>
Add I2C controller support for Cortina Access CAxxxx SoCs
---
Changes in v3: None
Changes in v2: None
MAINTAINERS | 4 + drivers/i2c/Kconfig | 7 + drivers/i2c/Makefile | 1 + drivers/i2c/i2c-cortina.c | 346 ++++++++++++++++++++++++++++++++++++++++++++++ drivers/i2c/i2c-cortina.h | 92 ++++++++++++ 5 files changed, 450 insertions(+) create mode 100644 drivers/i2c/i2c-cortina.c create mode 100644 drivers/i2c/i2c-cortina.h
MAINTAINERS +4 -0
@@ -181,6 +181,8 @@ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c F: drivers/mmc/ca_dw_mmc.c +F: drivers/i2c/i2c-cortina.c +F: drivers/i2c/i2c-cortina.h ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <[email protected]>
@@ -672,6 +674,8 @@ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c F: drivers/mmc/ca_dw_mmc.c +F: drivers/i2c/i2c-cortina.c +F: drivers/i2c/i2c-cortina.h MIPS MSCC M: Gregory CLEMENT <[email protected]>
drivers/i2c/Kconfig +7 -0
@@ -85,6 +85,13 @@ config SYS_I2C_CADENCE Say yes here to select Cadence I2C Host Controller. This controller is e.g. used by Xilinx Zynq. +config SYS_I2C_CA + tristate "Cortina-Access I2C Controller" + depends on DM_I2C && CORTINA_PLATFORM + default n + help + Say yes here to select Cortina-Access I2C Host Controller. + config SYS_I2C_DAVINCI bool "Davinci I2C Controller" depends on (ARCH_KEYSTONE || ARCH_DAVINCI)
drivers/i2c/Makefile +1 -0
@@ -12,6 +12,7 @@ obj-$(CONFIG_SYS_I2C) += i2c_core.o obj-$(CONFIG_SYS_I2C_ASPEED) += ast_i2c.o obj-$(CONFIG_SYS_I2C_AT91) += at91_i2c.o obj-$(CONFIG_SYS_I2C_CADENCE) += i2c-cdns.o +obj-$(CONFIG_SYS_I2C_CA) += i2c-cortina.o obj-$(CONFIG_SYS_I2C_DAVINCI) += davinci_i2c.o obj-$(CONFIG_SYS_I2C_DW) += designware_i2c.o ifdef CONFIG_DM_PCI
drivers/i2c/i2c-cortina.c new file +346 -0
346 lines not on this page · raw message
drivers/i2c/i2c-cortina.h new file +92 -0
92 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 4/8 board: presidio-asic: Add I2C support
In reply to Alex NemirovskyAdd I2C board support for Cortina Access Presidio Engineering Board
---
Changes in v3: None
Changes in v2: None
configs/cortina_presidio-asic-emmc_defconfig | 3 +++ 1 file changed, 3 insertions(+)
configs/cortina_presidio-asic-emmc_defconfig +3 -0
@@ -10,6 +10,7 @@ CONFIG_SHOW_BOOT_PROGRESS=y CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_R=y CONFIG_SYS_PROMPT="G3#" +CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y CONFIG_CMD_PART=y CONFIG_CMD_WDT=y
@@ -24,6 +25,8 @@ CONFIG_DEFAULT_DEVICE_TREE="ca-presidio-engboard" # CONFIG_NET is not set CONFIG_DM=y CONFIG_CORTINA_GPIO=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_CA=y CONFIG_DM_MMC=y CONFIG_MMC_DW=y CONFIG_MMC_DW_CORTINA=y
Signature · 1 line
2.7.4
PATCH v2 5/8 led: led_cortina: Add CAxxx LED support
In reply to Alex NemirovskyFrom: Jway Lin <[email protected]>
Add Cortina Access LED controller support for CAxxxx SOCs
---
Changes in v3: None
Changes in v2: None
MAINTAINERS | 2 + drivers/led/Kconfig | 8 ++ drivers/led/Makefile | 1 + drivers/led/led_cortina.c | 308 ++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 319 insertions(+) create mode 100644 drivers/led/led_cortina.c
MAINTAINERS +2 -0
@@ -183,6 +183,7 @@ F: drivers/serial/serial_cortina.c F: drivers/mmc/ca_dw_mmc.c F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h +F: drivers/led/led_cortina.c ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <[email protected]>
@@ -676,6 +677,7 @@ F: drivers/serial/serial_cortina.c F: drivers/mmc/ca_dw_mmc.c F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h +F: drivers/led/led_cortina.c MIPS MSCC M: Gregory CLEMENT <[email protected]>
drivers/led/Kconfig +8 -0
@@ -35,6 +35,14 @@ config LED_BCM6858 This option enables support for LEDs connected to the BCM6858 HW has blinking capabilities and up to 32 LEDs can be controlled. +config LED_CORTINA + bool "LED Support for Cortina Access CAxxxx SoCs" + depends on LED && (CORTINA_PLATFORM) + help + This option enables support for LEDs connected to the Cortina + Access CAxxxx SOCs. + + config LED_BLINK bool "Support LED blinking" depends on LED
drivers/led/Makefile +1 -0
@@ -8,3 +8,4 @@ obj-$(CONFIG_LED_BCM6328) += led_bcm6328.o obj-$(CONFIG_LED_BCM6358) += led_bcm6358.o obj-$(CONFIG_LED_BCM6858) += led_bcm6858.o obj-$(CONFIG_$(SPL_)LED_GPIO) += led_gpio.o +obj-$(CONFIG_LED_CORTINA) += led_cortina.o
drivers/led/led_cortina.c new file +308 -0
308 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 6/8 board: presidio: add LED support
In reply to Alex NemirovskyFrom: Jway Lin <[email protected]>
Add LED support for Cortina Access Presidio Engineering Board
---
Changes in v3: None
Changes in v2: None
arch/arm/dts/ca-presidio-engboard.dts | 31 ++++++++++++++++++++++++++++ configs/cortina_presidio-asic-emmc_defconfig | 2 ++ 2 files changed, 33 insertions(+)
arch/arm/dts/ca-presidio-engboard.dts +31 -0
@@ -66,4 +66,35 @@ spi-max-frequency = <108000000>; }; }; + + leds: led-controller at f43200f0 { + compatible = "cortina,ca-leds"; + reg = <0x0 0xf43200f0 0x40>; + + cortina,blink_rate1 = <256>; + cortina,blink_rate2 = <512>; + + led at 0 { + pin = <0>; + active-low; + blink-sel =<0>; + port = <0>; + off-event = <0>; + label = "led0"; + }; + + led at 1 { + pin = <1>; + active-low; + blink-sel =<1>; + label = "led1"; + }; + + led at 2 { + pin = <2>; + active-low; + label = "led2"; + }; + + }; };
configs/cortina_presidio-asic-emmc_defconfig +2 -0
@@ -27,6 +27,8 @@ CONFIG_DM=y CONFIG_CORTINA_GPIO=y CONFIG_DM_I2C=y CONFIG_SYS_I2C_CA=y +CONFIG_LED=y +CONFIG_LED_CORTINA=y CONFIG_DM_MMC=y CONFIG_MMC_DW=y CONFIG_MMC_DW_CORTINA=y
Signature · 1 line
2.7.4
PATCH v2 7/8 spi: ca_sflash: Add CAxxxx SPI Flash Controller
In reply to Alex NemirovskyFrom: Pengpeng Chen <[email protected]>
Add SPI Flash controller driver for Cortina Access CAxxxx SoCs
---
Changes in v3:
- Fixup syntax issues related to checkpatch.pl cleanup
Changes in v2: None
MAINTAINERS | 2 + drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 + drivers/spi/ca_sflash.c | 576 ++++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 587 insertions(+) create mode 100644 drivers/spi/ca_sflash.c
MAINTAINERS +2 -0
@@ -184,6 +184,7 @@ F: drivers/mmc/ca_dw_mmc.c F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h F: drivers/led/led_cortina.c +F: drivers/spi/ca_sflash.c ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <[email protected]>
@@ -678,6 +679,7 @@ F: drivers/mmc/ca_dw_mmc.c F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h F: drivers/led/led_cortina.c +F: drivers/spi/ca_sflash.c MIPS MSCC M: Gregory CLEMENT <[email protected]>
drivers/spi/Kconfig +8 -0
@@ -106,6 +106,14 @@ config BCMSTB_SPI be used to access the SPI flash on platforms embedding this Broadcom SPI core. +config CORTINA_SFLASH + bool "Cortina-Access Serial Flash controller driver" + depends on DM_SPI && SPI_MEM + help + Enable the Cortina-Access Serial Flash controller driver. This driver + can be used to access the SPI NOR/NAND flash on platforms embedding this + Cortina-Access IP core. + config CADENCE_QSPI bool "Cadence QSPI driver" help
drivers/spi/Makefile +1 -0
@@ -25,6 +25,7 @@ obj-$(CONFIG_BCM63XX_SPI) += bcm63xx_spi.o obj-$(CONFIG_BCMSTB_SPI) += bcmstb_spi.o obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o obj-$(CONFIG_CF_SPI) += cf_spi.o +obj-$(CONFIG_CORTINA_SFLASH) += ca_sflash.o obj-$(CONFIG_DAVINCI_SPI) += davinci_spi.o obj-$(CONFIG_DESIGNWARE_SPI) += designware_spi.o obj-$(CONFIG_EXYNOS_SPI) += exynos_spi.o
drivers/spi/ca_sflash.c new file +576 -0
576 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 8/8 board: presidio-asic: Add SPI NAND and NOR support
In reply to Alex NemirovskyAdd SPI NAND and NOR support for Cortina Access
Presidio Engineering Board
---
Changes in v3: None
Changes in v2: None
arch/arm/dts/ca-presidio-engboard.dts | 8 ++-- board/cortina/presidio-asic/presidio.c | 16 ++++++- configs/cortina_presidio-asic-spi-nand_defconfig | 48 +++++++++++++++++++ configs/cortina_presidio-asic-spi-nor_defconfig | 59 ++++++++++++++++++++++++ 4 files changed, 125 insertions(+), 6 deletions(-) create mode 100644 configs/cortina_presidio-asic-spi-nand_defconfig create mode 100644 configs/cortina_presidio-asic-spi-nor_defconfig
arch/arm/dts/ca-presidio-engboard.dts +3 -5
@@ -55,15 +55,13 @@ }; sflash: sflash-controller at f4324000 { - #address-cells = <2>; - #size-cells = <1>; compatible = "cortina,ca-sflash"; reg = <0x0 0xf4324000 0x50>; reg-names = "sflash-regs"; flash at 0 { - compatible = "jedec,spi-nor"; - spi-rx-bus-width = <1>; - spi-max-frequency = <108000000>; + compatible = "spi-nand", "jedec,spi-nor"; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <4>; }; };
board/cortina/presidio-asic/presidio.c +15 -1
@@ -14,7 +14,7 @@#include <asm/psci.h> #include <cpu_func.h> #include <asm/armv8/mmu.h> - +#include <dm/uclass.h> DECLARE_GLOBAL_DATA_PTR ;#define CA_PERIPH_BASE 0xE0000000UL
@@ -70,9 +70,23 @@ static noinline int invoke_psci_fn_smc(u64 function_id, u64 arg0, u64 arg1,return function_id; } +#ifdef CONFIG_CORTINA_SFLASH +static int init_sflash (void ) +{ +struct udevice *dev; + +uclass_first_device (UCLASS_SPI , &dev); + +return 0 ; +} +#endif +int board_early_init_r (void ) {dcache_disable (); +#ifdef CONFIG_CORTINA_SFLASH +init_sflash (); +#endif return 0 ; }
configs/cortina_presidio-asic-spi-nand_defconfig new file +48 -0
48 lines not on this page · raw message
configs/cortina_presidio-asic-spi-nor_defconfig new file +59 -0
59 lines not on this page · raw message
Signature · 1 line
2.7.4