Skip to contentSkip to conversation

arm64: dts: meson: add dts/bindings for SmartLabs SML-5442TW

PATCH Superseded Christian Hewitt 3 participants 8 messages Mar 1, 2020 – Mar 3, 2020

Subsystems (2)

v6 of 8 Superseded Latest is v8 →

lore
Share & tools
lore
#0 lore raw

v6 cover arm64: dts: meson: add dts/bindings for SmartLabs SML-5442TW

This series adds new bindings and a device-tree file for the Smartlabs SML-5442TW set-top box. The previous v3 attempt [1] was 15-months ago but nothing has really changed apart from a change to yaml bindings. I have checked and the hci_qca driver does not provide QCA9377 bindings so there is no alernative to the gpio-hog for enabling BT support.

v6 - removed audio nodes again

v5 - typo in card name

v4 - typos/corrections from Andreas
- convert to yaml bindings
- add sound node back
- confirmed gpio-hog is necessary

v3 - change to Smartlabs LLC
- removed sound node

v2 - removed audio nodes
- changes soundcard name to "meson-gx-audio"
- added missing uart-has-rtscts;

[1] https://patchwork.kernel.org/cover/10674939/

Christian Hewitt (3):
dt-bindings: add vendor prefix for SmartLabs LLC
dt-bindings: arm: amlogic: add support for the SmartLabs SML-5442TW
arm64: dts: meson: add support for the SmartLabs SML-5442TW

 Documentation/devicetree/bindings/arm/amlogic.yaml |   1 +
 .../devicetree/bindings/vendor-prefixes.yaml       |   2 +
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++
 4 files changed, 296 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
Signature · 1 line
2.7.4
#1 lore raw

PATCH v6 1/3 dt-bindings: add vendor prefix for SmartLabs LLC

SmartLabs LLC are a professional integrator of Interactive TV solutions and IPTV/VOD devices [1].

[1] https://www.smartlabs.tv/en/about/

---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
index 9e67944..a34ed82 100644
@@ -901,6 +901,8 @@ patternProperties:
     description: Sitronix Technology Corporation
   "^skyworks,.*":
     description: Skyworks Solutions, Inc.
+  "^smartlabs,.*":
+    description: SmartLabs LLC
   "^smsc,.*":
     description: Standard Microsystems Corporation
   "^snps,.*":
Signature · 1 line
2.7.4
maintainer Acked-by on v6 1/3
#2 lore raw

Re: [PATCH v6 1/3] dt-bindings: add vendor prefix for SmartLabs LLC

Quoted 10 lines · Christian Hewitt

SmartLabs LLC are a professional integrator of Interactive TV solutions and IPTV/VOD devices [1].

[1] https://www.smartlabs.tv/en/about/

---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)
#3 lore raw

PATCH v6 2/3 dt-bindings: arm: amlogic: add support for the SmartLabs SML-5442TW

In reply to Christian Hewitt

The SML-5442TW is an STB for O2 Czech IPTV/VOD and DVB-T/T2 based on the Amlogic P231 reference design using the S905D chipset. Specs:

2GB DDR3 RAM
8GB eMMC storage
10/100 Base-T Ethernet
802.11 a/b/g/n/ac + BT 4.1 HS sdio wireless module (QCA9377) 2x single colour and 1x dual colour LEDs on the front panel 1x reset button on the front panel
HDMI 2.0 (4k@60p) video
Composite video + 2-channel audio output on 3.5mm jack S/PDIF audio output
Single DVB-T/T2 tuner (AVL6762/MxL608)
2x USB 2.0 ports
1x micro SD card slot
UART pins (internal)

---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/amlogic.yaml +1 -0
index f74aba4..c0c0f66 100644
@@ -107,6 +107,7 @@ properties:
               - amlogic,p231
               - libretech,aml-s905d-pc
               - phicomm,n1
+              - smartlabs,sml5442tw
           - const: amlogic,s905d
           - const: amlogic,meson-gxl
 
Signature · 1 line
2.7.4
maintainer Acked-by on v6 2/3
#4 lore raw

Re: [PATCH v6 2/3] dt-bindings: arm: amlogic: add support for the SmartLabs SML-5442TW

Quoted 17 lines · Christian Hewitt

The SML-5442TW is an STB for O2 Czech IPTV/VOD and DVB-T/T2 based on the Amlogic P231 reference design using the S905D chipset. Specs:

2GB DDR3 RAM
8GB eMMC storage
10/100 Base-T Ethernet
802.11 a/b/g/n/ac + BT 4.1 HS sdio wireless module (QCA9377) 2x single colour and 1x dual colour LEDs on the front panel 1x reset button on the front panel
HDMI 2.0 (4k@60p) video
Composite video + 2-channel audio output on 3.5mm jack S/PDIF audio output
Single DVB-T/T2 tuner (AVL6762/MxL608)
2x USB 2.0 ports
1x micro SD card slot
UART pins (internal)

Quoted 5 lines
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
 1 file changed, 1 insertion(+)
#5 lore raw

PATCH v6 3/3 arm64: dts: meson: add support for the SmartLabs SML-5442TW

In reply to Christian Hewitt

The SmartLabs SML-5442TW is broadly similar to the P231 reference design but with the following differences:

- The Yellow and Blue LEDs are available but disabled
- The Red and Green LEDs are used to signal off/on status
- uart_AO can be accessed after opening the case; soldered pins exist
- GPIOX_17 is forced high to enable the QCA9377 module

---
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++
 2 files changed, 293 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
arch/arm64/boot/dts/amlogic/Makefile +1 -0
index eef0045..6cf8c4a 100644
@@ -27,6 +27,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-phicomm-n1.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +292 -0

292 lines not on this page · raw message

Signature · 1 line
2.7.4
#6 lore raw

Re: [PATCH v6 3/3] arm64: dts: meson: add support for the SmartLabs SML-5442TW

Hi,

Quoted 60 lines · Christian Hewitt

The SmartLabs SML-5442TW is broadly similar to the P231 reference design but with the following differences:

- The Yellow and Blue LEDs are available but disabled
- The Red and Green LEDs are used to signal off/on status
- uart_AO can be accessed after opening the case; soldered pins exist
- GPIOX_17 is forced high to enable the QCA9377 module

---
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++
 2 files changed, 293 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
arch/arm64/boot/dts/amlogic/Makefile +1 -0
index eef0045..6cf8c4a 100644
@@ -27,6 +27,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-phicomm-n1.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +27 -0
new file mode 100644
index 0000000..5fdf1ca
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <[email protected]>
+ * Copyright (c) 2018 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905d.dtsi"
+
+/ {
+	compatible = "smartlabs,sml5442tw", "amlogic,s905d",
+		"amlogic,meson-gxl";
+	model = "SmartLabs SML-5442TW";
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+

arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 37

Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10 -0
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		yellow {
+			label = "sml5442tw:yellow";

The bindings of leds has changed, now you should use function and color ids as described in Documentation/devicetree/bindings/leds/common.yaml

Quoted 122 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +122 -0
+			gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		blue {
+			label = "sml5442tw:blue";
+			gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		green {
+			label = "sml5442tw:green";
+			gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		red {
+			label = "sml5442tw:red";
+			gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	hdmi_5v: regulator-hdmi-5v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "HDMI_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};

arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 169

Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10 -0
+
+/* This will enable the bluetooth module */
+&gpio {
+	bt-en {
+		gpio-hog;
+		gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "bt-en";
+	};
+};

Did you try using the qcom,qca6174-bt compatible similar to the broadcom BT module as described in Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt ?

Quoted 114 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +113 -0
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&hdmi_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&i2c_A {
+	status = "okay";
+	pinctrl-0 = <&i2c_a_pins>;
+	pinctrl-names = "default";
+};
+
+&internal_phy {
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <100000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* This is connected to the Bluetooth module: */
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+

arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 292

Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10 -0
+/* This UART is brought out to the debug header */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0 {
+	status = "okay";
+};

Neil

#7 lore raw

Re: [PATCH v6 3/3] arm64: dts: meson: add support for the SmartLabs SML-5442TW

In reply to Christian Hewitt

Hi,

Quoted 60 lines · Christian Hewitt

The SmartLabs SML-5442TW is broadly similar to the P231 reference design but with the following differences:

- The Yellow and Blue LEDs are available but disabled
- The Red and Green LEDs are used to signal off/on status
- uart_AO can be accessed after opening the case; soldered pins exist
- GPIOX_17 is forced high to enable the QCA9377 module

---
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++
 2 files changed, 293 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
arch/arm64/boot/dts/amlogic/Makefile +1 -0
index eef0045..6cf8c4a 100644
@@ -27,6 +27,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-phicomm-n1.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +27 -0
new file mode 100644
index 0000000..5fdf1ca
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <[email protected]>
+ * Copyright (c) 2018 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905d.dtsi"
+
+/ {
+	compatible = "smartlabs,sml5442tw", "amlogic,s905d",
+		"amlogic,meson-gxl";
+	model = "SmartLabs SML-5442TW";
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+

arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 37

Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10 -0
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		yellow {
+			label = "sml5442tw:yellow";

The bindings of leds has changed, now you should use function and color ids as described in Documentation/devicetree/bindings/leds/common.yaml

Quoted 122 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +122 -0
+			gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		blue {
+			label = "sml5442tw:blue";
+			gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		green {
+			label = "sml5442tw:green";
+			gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		red {
+			label = "sml5442tw:red";
+			gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	hdmi_5v: regulator-hdmi-5v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "HDMI_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};

arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 169

Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10 -0
+
+/* This will enable the bluetooth module */
+&gpio {
+	bt-en {
+		gpio-hog;
+		gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "bt-en";
+	};
+};

Did you try using the qcom,qca6174-bt compatible similar to the broadcom BT module as described in Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt ?

Quoted 114 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +113 -0
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&hdmi_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&i2c_A {
+	status = "okay";
+	pinctrl-0 = <&i2c_a_pins>;
+	pinctrl-names = "default";
+};
+
+&internal_phy {
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <100000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* This is connected to the Bluetooth module: */
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+

arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 292

Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10 -0
+/* This UART is brought out to the debug header */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0 {
+	status = "okay";
+};

Neil