arm64: dts: meson: add dts/bindings for SmartLabs SML-5442TW
Subsystems (2)
v6 cover arm64: dts: meson: add dts/bindings for SmartLabs SML-5442TW
This series adds new bindings and a device-tree file for the Smartlabs SML-5442TW set-top box. The previous v3 attempt [1] was 15-months ago but nothing has really changed apart from a change to yaml bindings. I have checked and the hci_qca driver does not provide QCA9377 bindings so there is no alernative to the gpio-hog for enabling BT support.
v6 - removed audio nodes again
v5 - typo in card name
v4 - typos/corrections from Andreas
- convert to yaml bindings
- add sound node back
- confirmed gpio-hog is necessary
v3 - change to Smartlabs LLC
- removed sound node
v2 - removed audio nodes
- changes soundcard name to "meson-gx-audio"
- added missing uart-has-rtscts;
[1] https://patchwork.kernel.org/cover/10674939/
Christian Hewitt (3):
dt-bindings: add vendor prefix for SmartLabs LLC
dt-bindings: arm: amlogic: add support for the SmartLabs SML-5442TW
arm64: dts: meson: add support for the SmartLabs SML-5442TW
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 + .../devicetree/bindings/vendor-prefixes.yaml | 2 + arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++ 4 files changed, 296 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
Signature · 1 line
2.7.4
PATCH v6 1/3 dt-bindings: add vendor prefix for SmartLabs LLC
SmartLabs LLC are a professional integrator of Interactive TV solutions and IPTV/VOD devices [1].
[1] https://www.smartlabs.tv/en/about/
--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
@@ -901,6 +901,8 @@ patternProperties: description: Sitronix Technology Corporation "^skyworks,.*": description: Skyworks Solutions, Inc. + "^smartlabs,.*": + description: SmartLabs LLC "^smsc,.*": description: Standard Microsystems Corporation "^snps,.*":
Signature · 1 line
2.7.4
Re: [PATCH v6 1/3] dt-bindings: add vendor prefix for SmartLabs LLC
Quoted 10 lines · Christian Hewitt
SmartLabs LLC are a professional integrator of Interactive TV solutions and IPTV/VOD devices [1].
[1] https://www.smartlabs.tv/en/about/
Signed-off-by Christian Hewitt <[email protected]>--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
PATCH v6 2/3 dt-bindings: arm: amlogic: add support for the SmartLabs SML-5442TW
In reply to Christian HewittThe SML-5442TW is an STB for O2 Czech IPTV/VOD and DVB-T/T2 based on the Amlogic P231 reference design using the S905D chipset. Specs:
2GB DDR3 RAM
8GB eMMC storage
10/100 Base-T Ethernet
802.11 a/b/g/n/ac + BT 4.1 HS sdio wireless module (QCA9377) 2x single colour and 1x dual colour LEDs on the front panel 1x reset button on the front panel
HDMI 2.0 (4k@60p) video
Composite video + 2-channel audio output on 3.5mm jack S/PDIF audio output
Single DVB-T/T2 tuner (AVL6762/MxL608)
2x USB 2.0 ports
1x micro SD card slot
UART pins (internal)
--- Documentation/devicetree/bindings/arm/amlogic.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/amlogic.yaml +1 -0
@@ -107,6 +107,7 @@ properties: - amlogic,p231 - libretech,aml-s905d-pc - phicomm,n1 + - smartlabs,sml5442tw - const: amlogic,s905d - const: amlogic,meson-gxl
Signature · 1 line
2.7.4
Re: [PATCH v6 2/3] dt-bindings: arm: amlogic: add support for the SmartLabs SML-5442TW
Quoted 17 lines · Christian Hewitt
The SML-5442TW is an STB for O2 Czech IPTV/VOD and DVB-T/T2 based on the Amlogic P231 reference design using the S905D chipset. Specs:
2GB DDR3 RAM
8GB eMMC storage
10/100 Base-T Ethernet
802.11 a/b/g/n/ac + BT 4.1 HS sdio wireless module (QCA9377) 2x single colour and 1x dual colour LEDs on the front panel 1x reset button on the front panel
HDMI 2.0 (4k@60p) video
Composite video + 2-channel audio output on 3.5mm jack S/PDIF audio output
Single DVB-T/T2 tuner (AVL6762/MxL608)
2x USB 2.0 ports
1x micro SD card slot
UART pins (internal)
Quoted 5 lines
Signed-off-by Christian Hewitt <[email protected]>--- Documentation/devicetree/bindings/arm/amlogic.yaml | 1 + 1 file changed, 1 insertion(+)
PATCH v6 3/3 arm64: dts: meson: add support for the SmartLabs SML-5442TW
In reply to Christian HewittThe SmartLabs SML-5442TW is broadly similar to the P231 reference design but with the following differences:
- The Yellow and Blue LEDs are available but disabled
- The Red and Green LEDs are used to signal off/on status
- uart_AO can be accessed after opening the case; soldered pins exist
- GPIOX_17 is forced high to enable the QCA9377 module
--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++ 2 files changed, 293 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
arch/arm64/boot/dts/amlogic/Makefile +1 -0
@@ -27,6 +27,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-phicomm-n1.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +292 -0
292 lines not on this page · raw message
Signature · 1 line
2.7.4
Re: [PATCH v6 3/3] arm64: dts: meson: add support for the SmartLabs SML-5442TW
Hi,
Quoted 60 lines · Christian Hewitt
The SmartLabs SML-5442TW is broadly similar to the P231 reference design but with the following differences:
- The Yellow and Blue LEDs are available but disabled
- The Red and Green LEDs are used to signal off/on status
-uart_AOcan be accessed after opening the case; soldered pins exist
-GPIOX_17is forced high to enable the QCA9377 moduleSigned-off-by Christian Hewitt <[email protected]>--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++ 2 files changed, 293 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dtsarch/arm64/boot/dts/amlogic/Makefile +1
-0@@ -27,6 +27,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-phicomm-n1.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtbarch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +27
-0@@ -0,0 +1,292 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2016 Endless Computers, Inc. + * Author: Carlo Caione <[email protected]> + * Copyright (c) 2018 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-gxl-s905d.dtsi" + +/ { + compatible = "smartlabs,sml5442tw", "amlogic,s905d", + "amlogic,meson-gxl"; + model = "SmartLabs SML-5442TW"; + + aliases { + serial0 = &uart_AO; + serial1 = &uart_A; + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 37
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10
-0+ memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + leds { + compatible = "gpio-leds"; + + yellow { + label = "sml5442tw:yellow";
The bindings of leds has changed, now you should use function and color ids as described in Documentation/devicetree/bindings/leds/common.yaml
Quoted 122 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +122
-0+ gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + blue { + label = "sml5442tw:blue"; + gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + green { + label = "sml5442tw:green"; + gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + red { + label = "sml5442tw:red"; + gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + hdmi_5v: regulator-hdmi-5v { + compatible = "regulator-fixed"; + + regulator-name = "HDMI_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + vddio_ao18: regulator-vddio_ao18 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddio_boot: regulator-vddio_boot { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_BOOT"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; + + cvbs-connector { + compatible = "composite-video-connector"; + + port { + cvbs_connector_in: endpoint { + remote-endpoint = <&cvbs_vdac_out>; + }; + }; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; +}; + +&cec_AO { + status = "okay"; + pinctrl-0 = <&ao_cec_pins>; + pinctrl-names = "default"; + hdmi-phandle = <&hdmi_tx>; +}; + +&cvbs_vdac_port { + cvbs_vdac_out: endpoint { + remote-endpoint = <&cvbs_connector_in>; + }; +}; + +ðmac { + status = "okay"; + phy-mode = "rmii"; + phy-handle = <&internal_phy>; +};
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 169
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10
-0+ +/* This will enable the bluetooth module */ +&gpio { + bt-en { + gpio-hog; + gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "bt-en"; + }; +};
Did you try using the qcom,qca6174-bt compatible similar to the broadcom BT module as described in Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt ?
Quoted 114 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +113
-0+ +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>; + pinctrl-names = "default"; + hdmi-supply = <&hdmi_5v>; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; + +&i2c_A { + status = "okay"; + pinctrl-0 = <&i2c_a_pins>; + pinctrl-names = "default"; +}; + +&internal_phy { + pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>; + pinctrl-names = "default"; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; +}; + +&pwm_ef { + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; + clocks = <&clkc CLKID_FCLK_DIV4>; + clock-names = "clkin0"; +}; + +&saradc { + status = "okay"; + vref-supply = <&vddio_ao18>; +}; + +/* Wireless SDIO Module */ +&sd_emmc_a { + status = "okay"; + pinctrl-0 = <&sdio_pins>; + pinctrl-1 = <&sdio_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + #address-cells = <1>; + #size-cells = <0>; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + + non-removable; + disable-wp; + + mmc-pwrseq = <&sdio_pwrseq>; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_pins>; + pinctrl-1 = <&sdcard_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + disable-wp; + + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>; + cd-inverted; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + max-frequency = <100000000>; + non-removable; + disable-wp; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* This is connected to the Bluetooth module: */ +&uart_A { + status = "okay"; + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; +}; +
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 292
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10
-0+/* This UART is brought out to the debug header */ +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb0 { + status = "okay"; +};
Neil
Re: [PATCH v6 3/3] arm64: dts: meson: add support for the SmartLabs SML-5442TW
In reply to Christian HewittHi,
Quoted 60 lines · Christian Hewitt
The SmartLabs SML-5442TW is broadly similar to the P231 reference design but with the following differences:
- The Yellow and Blue LEDs are available but disabled
- The Red and Green LEDs are used to signal off/on status
-uart_AOcan be accessed after opening the case; soldered pins exist
-GPIOX_17is forced high to enable the QCA9377 moduleSigned-off-by Christian Hewitt <[email protected]>--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++ 2 files changed, 293 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dtsarch/arm64/boot/dts/amlogic/Makefile +1
-0@@ -27,6 +27,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-phicomm-n1.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtbarch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +27
-0@@ -0,0 +1,292 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2016 Endless Computers, Inc. + * Author: Carlo Caione <[email protected]> + * Copyright (c) 2018 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-gxl-s905d.dtsi" + +/ { + compatible = "smartlabs,sml5442tw", "amlogic,s905d", + "amlogic,meson-gxl"; + model = "SmartLabs SML-5442TW"; + + aliases { + serial0 = &uart_AO; + serial1 = &uart_A; + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 37
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10
-0+ memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + leds { + compatible = "gpio-leds"; + + yellow { + label = "sml5442tw:yellow";
The bindings of leds has changed, now you should use function and color ids as described in Documentation/devicetree/bindings/leds/common.yaml
Quoted 122 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +122
-0+ gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + blue { + label = "sml5442tw:blue"; + gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + green { + label = "sml5442tw:green"; + gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + red { + label = "sml5442tw:red"; + gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + hdmi_5v: regulator-hdmi-5v { + compatible = "regulator-fixed"; + + regulator-name = "HDMI_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + vddio_ao18: regulator-vddio_ao18 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddio_boot: regulator-vddio_boot { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_BOOT"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; + + cvbs-connector { + compatible = "composite-video-connector"; + + port { + cvbs_connector_in: endpoint { + remote-endpoint = <&cvbs_vdac_out>; + }; + }; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; +}; + +&cec_AO { + status = "okay"; + pinctrl-0 = <&ao_cec_pins>; + pinctrl-names = "default"; + hdmi-phandle = <&hdmi_tx>; +}; + +&cvbs_vdac_port { + cvbs_vdac_out: endpoint { + remote-endpoint = <&cvbs_connector_in>; + }; +}; + +ðmac { + status = "okay"; + phy-mode = "rmii"; + phy-handle = <&internal_phy>; +};
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 169
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10
-0+ +/* This will enable the bluetooth module */ +&gpio { + bt-en { + gpio-hog; + gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "bt-en"; + }; +};
Did you try using the qcom,qca6174-bt compatible similar to the broadcom BT module as described in Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt ?
Quoted 114 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +113
-0+ +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>; + pinctrl-names = "default"; + hdmi-supply = <&hdmi_5v>; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; + +&i2c_A { + status = "okay"; + pinctrl-0 = <&i2c_a_pins>; + pinctrl-names = "default"; +}; + +&internal_phy { + pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>; + pinctrl-names = "default"; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; +}; + +&pwm_ef { + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; + clocks = <&clkc CLKID_FCLK_DIV4>; + clock-names = "clkin0"; +}; + +&saradc { + status = "okay"; + vref-supply = <&vddio_ao18>; +}; + +/* Wireless SDIO Module */ +&sd_emmc_a { + status = "okay"; + pinctrl-0 = <&sdio_pins>; + pinctrl-1 = <&sdio_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + #address-cells = <1>; + #size-cells = <0>; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + + non-removable; + disable-wp; + + mmc-pwrseq = <&sdio_pwrseq>; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_pins>; + pinctrl-1 = <&sdcard_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + disable-wp; + + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>; + cd-inverted; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + max-frequency = <100000000>; + non-removable; + disable-wp; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* This is connected to the Bluetooth module: */ +&uart_A { + status = "okay"; + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; +}; +
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts line 292
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file +10
-0+/* This UART is brought out to the debug header */ +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb0 { + status = "okay"; +};
Neil