Actions S700 SoC support
Subsystems (6)
v4 cover Actions S700 SoC support
This adds Cubieboard7[1] support based on Action Semi's S700 SoC[2], It's Quad-core ARMv8 SoC with Cortex-A53 cores. Peripheral like UART seems to be compatible with S900 SoC(basic support for it is alreay present in u-boot).
This series(v4) is much shorter than the previous series(v3) as patches related to Ethernet support is dropped along with reset driver patches.
First few patches(from 1/11 to 3/11) consolidates Actions Semiconductor SoCs support in u-boot(mostly insprired by SUXNI as suggested by Andre). Idea is to move every bit out from board/ucRobotics into arch/arm/mach-owl. It allows different SoCs to be driven by single "soc and Kconfig" file. It also includes common clock driver for S700 and S900. Patches(from 4/11 to 6/11 and 10/21 to 11/11) enables S700 SoC support alongwith Cubieboard7 board.
While at it, took the opportunity to sync S900 DT sources and bindings(patches from 7/11 to 8/11) with Linux(tag v5.5-rc6) and it is compiled-tested.
S700 support is tested[3] on Cubieboard7 board and S900 support is just compiled tested.
This patch series can be tested using below tree:
https://github.com/Atomar25/u-boot/commits/s700_v4
[1]: http://www.cubietech.com/product-detail/cubieboard7/
[2]: http://www.actions-semi.com/en/productview.aspx?id=225
[3]: https://paste.ubuntu.com/p/4cpxhSmFg5/
Amit Singh Tomar (11):
arm: actions: Add common framework for Actions Owl Semi SoCs
arm: actions: rename sysmap-s900 to sysmap-owl
clk: actions: Add common clock driver
arm: add support Actions Semi S700
arm: actions: add S700 SoC device tree
arm: dts: actions: s700: add u-boot specific dtsi file
arm: dts: sync dts for Action Semi S900
arm: dts: actions: s900: add u-boot specific dtsi file
serial: actions: add uart support for s700
arm: add Cubieboard7 board support
doc: boards: add Cubieboard7 documentation
MAINTAINERS | 2 + arch/arm/Kconfig | 5 +- arch/arm/dts/Makefile | 6 +- arch/arm/dts/s700-cubieboard7.dts | 92 +++++++ arch/arm/dts/s700-u-boot.dtsi | 18 ++ arch/arm/dts/s700.dtsi | 248 +++++++++++++++++++ arch/arm/dts/s900-u-boot.dtsi | 17 ++ arch/arm/dts/s900.dtsi | 322 +++++++++++++++++++++++-- arch/arm/include/asm/arch-owl/clk_s900.h | 57 ----- arch/arm/include/asm/arch-owl/regs_s700.h | 56 +++++ arch/arm/mach-owl/Kconfig | 35 +-- arch/arm/mach-owl/Makefile | 3 +- arch/arm/mach-owl/soc.c | 57 +++++ arch/arm/mach-owl/sysmap-owl.c | 32 +++ arch/arm/mach-owl/sysmap-s900.c | 32 --- board/ucRobotics/bubblegum_96/Kconfig | 15 -- board/ucRobotics/bubblegum_96/MAINTAINERS | 6 - board/ucRobotics/bubblegum_96/Makefile | 3 - board/ucRobotics/bubblegum_96/bubblegum_96.c | 57 ----- configs/bubblegum_96_defconfig | 7 +- configs/cubieboard7_defconfig | 16 ++ doc/board/actions/cubieboard7.rst | 115 +++++++++ doc/board/actions/index.rst | 10 + doc/board/index.rst | 1 + drivers/clk/owl/Kconfig | 8 +- drivers/clk/owl/Makefile | 2 +- drivers/clk/owl/clk_owl.c | 147 +++++++++++ drivers/clk/owl/clk_owl.h | 65 +++++ drivers/clk/owl/clk_s900.c | 137 ----------- drivers/serial/serial_owl.c | 2 +- include/configs/bubblegum_96.h | 40 --- include/configs/owl-common.h | 40 +++ include/configs/s700.h | 13 + include/configs/s900.h | 16 ++ include/dt-bindings/clock/actions,s700-cmu.h | 118 +++++++++ include/dt-bindings/clock/actions,s900-cmu.h | 129 ++++++++++ include/dt-bindings/clock/s900_cmu.h | 77 ------ include/dt-bindings/reset/actions,s700-reset.h | 34 +++ include/dt-bindings/reset/actions,s900-reset.h | 65 +++++ 39 files changed, 1624 insertions(+), 481 deletions(-) create mode 100644 arch/arm/dts/s700-cubieboard7.dts create mode 100644 arch/arm/dts/s700-u-boot.dtsi create mode 100644 arch/arm/dts/s700.dtsi create mode 100644 arch/arm/dts/s900-u-boot.dtsi delete mode 100644 arch/arm/include/asm/arch-owl/clk_s900.h create mode 100644 arch/arm/include/asm/arch-owl/regs_s700.h create mode 100644 arch/arm/mach-owl/soc.c create mode 100644 arch/arm/mach-owl/sysmap-owl.c delete mode 100644 arch/arm/mach-owl/sysmap-s900.c delete mode 100644 board/ucRobotics/bubblegum_96/Kconfig delete mode 100644 board/ucRobotics/bubblegum_96/MAINTAINERS delete mode 100644 board/ucRobotics/bubblegum_96/Makefile delete mode 100644 board/ucRobotics/bubblegum_96/bubblegum_96.c create mode 100644 configs/cubieboard7_defconfig create mode 100644 doc/board/actions/cubieboard7.rst create mode 100644 doc/board/actions/index.rst create mode 100644 drivers/clk/owl/clk_owl.c create mode 100644 drivers/clk/owl/clk_owl.h delete mode 100644 drivers/clk/owl/clk_s900.c delete mode 100644 include/configs/bubblegum_96.h create mode 100644 include/configs/owl-common.h create mode 100644 include/configs/s700.h create mode 100644 include/configs/s900.h create mode 100644 include/dt-bindings/clock/actions,s700-cmu.h create mode 100644 include/dt-bindings/clock/actions,s900-cmu.h delete mode 100644 include/dt-bindings/clock/s900_cmu.h create mode 100644 include/dt-bindings/reset/actions,s700-reset.h create mode 100644 include/dt-bindings/reset/actions,s900-reset.h
Signature · 1 line
2.7.4
PATCH v4 1/11 arm: actions: Add common framework for Actions Owl Semi SoCs
This commit adds common arch support for Actions Semi Owl series SoCs and removes the Bubblegum96 board files.
---
Changes since v3:
* Corrected the file list entry in MAINTAINERS file.
Changes since v2:
* Moved the file list details to root MAINTAINERS file.
* Updated the commit message as suggested by Mani.
* Used the "Owl" keyword to describe SoC family.
Changes since v1:
* Moved S700 specific changes to patch 4 of 9.
* Moved couple of symbols from defconfig to arch/arm/Kconfig and platform owl Kconfig.
--- MAINTAINERS | 2 + arch/arm/Kconfig | 3 +- arch/arm/mach-owl/Kconfig | 29 ++++++-------- arch/arm/mach-owl/Makefile | 1 + arch/arm/mach-owl/soc.c | 57 ++++++++++++++++++++++++++++ board/ucRobotics/bubblegum_96/Kconfig | 15 -------- board/ucRobotics/bubblegum_96/MAINTAINERS | 6 --- board/ucRobotics/bubblegum_96/Makefile | 3 -- board/ucRobotics/bubblegum_96/bubblegum_96.c | 57 ---------------------------- configs/bubblegum_96_defconfig | 4 +- include/configs/bubblegum_96.h | 40 ------------------- include/configs/owl-common.h | 40 +++++++++++++++++++ include/configs/s900.h | 16 ++++++++ 13 files changed, 130 insertions(+), 143 deletions(-) create mode 100644 arch/arm/mach-owl/soc.c delete mode 100644 board/ucRobotics/bubblegum_96/Kconfig delete mode 100644 board/ucRobotics/bubblegum_96/MAINTAINERS delete mode 100644 board/ucRobotics/bubblegum_96/Makefile delete mode 100644 board/ucRobotics/bubblegum_96/bubblegum_96.c delete mode 100644 include/configs/bubblegum_96.h create mode 100644 include/configs/owl-common.h create mode 100644 include/configs/s900.h
MAINTAINERS +2 -0
@@ -274,6 +274,8 @@ F: arch/arm/mach-owl/ F: board/ucRobotics/ F: drivers/clk/owl/ F: drivers/serial/serial_owl.c +F: include/configs/owl-common.h +F: configs/bubblegum_96_defconfig ARM RENESAS RMOBILE/R-CAR M: Nobuhiro Iwamatsu <[email protected]>
arch/arm/Kconfig +1 -2
@@ -883,9 +883,9 @@ config ARCH_MX5 config ARCH_OWL bool "Actions Semi OWL SoCs" - select ARM64 select DM select DM_SERIAL + select OWL_SERIAL select OF_CONTROL imply CMD_DM
@@ -1875,7 +1875,6 @@ source "board/spear/spear600/Kconfig" source "board/spear/x600/Kconfig" source "board/st/stv0991/Kconfig" source "board/tcl/sl50/Kconfig" -source "board/ucRobotics/bubblegum_96/Kconfig" source "board/birdland/bav335x/Kconfig" source "board/toradex/colibri_pxa270/Kconfig" source "board/variscite/dart_6ul/Kconfig"
arch/arm/mach-owl/Kconfig +12 -17
@@ -1,27 +1,22 @@ if ARCH_OWL -config SYS_SOC - default "owl" - choice - prompt "Actions Semi OWL SoCs board select" + prompt "Actions Semi Owl SoC Variant" optional -config TARGET_BUBBLEGUM_96 - bool "96Boards Bubblegum-96" - help - Support for 96Boards Bubblegum-96. This board complies with - 96Board Consumer Edition Specification. Features: - - Actions Semi S900 SoC (4xCortex A53, Power VR G6230 GPU) - - 2GiB RAM - - 8GiB eMMC, uSD slot - - WiFi, Bluetooth and GPS module - - 2x Host, 1x Device USB port - - HDMI - - 20-pin low speed and 40-pin high speed expanders, 6 LED, 3 buttons +config MACH_S900 + bool "Actions Semi S900 SoC" + select ARM64 endchoice -source "board/ucRobotics/bubblegum_96/Kconfig" +config SYS_TEXT_BASE + default 0x11000000 + +config SYS_CONFIG_NAME + default "s900" if MACH_S900 + +config SYS_SOC + default "s900" if MACH_S900 endif
arch/arm/mach-owl/Makefile +1 -0
@@ -1,3 +1,4 @@ # SPDX-License-Identifier: GPL-2.0+ +obj-y += soc.o obj-y += sysmap-s900.o
arch/arm/mach-owl/soc.c new file +57 -0
57 lines not on this page · raw message
board/ucRobotics/bubblegum_96/Kconfig deleted +0 -15
@@ -1,15 +0,0 @@ -if TARGET_BUBBLEGUM_96 - -config SYS_BOARD - default "bubblegum_96" - -config SYS_VENDOR - default "ucRobotics" - -config SYS_SOC - default "s900" - -config SYS_CONFIG_NAME - default "bubblegum_96" - -endif
board/ucRobotics/bubblegum_96/MAINTAINERS deleted +0 -6
@@ -1,6 +0,0 @@ -BUBBLEGUM_96 BOARD -M: Manivannan Sadhasivam <[email protected]> -S: Maintained -F: board/ucRobotics/bubblegum_96/ -F: include/configs/bubblegum_96.h -F: configs/bubblegum_96_defconfig
board/ucRobotics/bubblegum_96/Makefile deleted +0 -3
@@ -1,3 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ - -obj-y := bubblegum_96.o
board/ucRobotics/bubblegum_96/bubblegum_96.c deleted +0 -57
57 lines not on this page · raw message
configs/bubblegum_96_defconfig +1 -3
@@ -1,9 +1,8 @@ CONFIG_ARM=y CONFIG_ARCH_OWL=y -CONFIG_SYS_TEXT_BASE=0x11000000 CONFIG_ENV_SIZE=0x2000 -CONFIG_TARGET_BUBBLEGUM_96=y CONFIG_NR_DRAM_BANKS=1 +CONFIG_MACH_S900=y CONFIG_IDENT_STRING="\nBubblegum-96" CONFIG_DISTRO_DEFAULTS=y CONFIG_BOOTDELAY=5
@@ -21,4 +20,3 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_CLK=y CONFIG_CLK_OWL=y CONFIG_CLK_S900=y -CONFIG_OWL_SERIAL=y
include/configs/bubblegum_96.h deleted +0 -40
@@ -1,40 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* -* Board configuration file for Bubblegum-96 -* -* Copyright (C) 2015 Actions Semi Co., Ltd. -* Copyright (C) 2018 Manivannan Sadhasivam <[email protected]> -* -*/ - -#ifndef _BUBBLEGUM_96_H_ -#define _BUGGLEGUM_96_H_ - -/* SDRAM Definitions */ -#define CONFIG_SYS_SDRAM_BASE 0x0 -#define CONFIG_SYS_SDRAM_SIZE 0x80000000 - -/* Generic Timer Definitions */ -#define COUNTER_FREQUENCY (24000000)/* 24MHz */ - -#define CONFIG_SYS_MALLOC_LEN (32 * 1024 * 1024) - -/* Some commands use this as the default load address */ -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7ffc0) - -/* -* This is the initial SP which is used only briefly for relocating the u-boot -* image to the top of SDRAM. After relocation u-boot moves the stack to the -* proper place. -*/ -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + 0x7ff00) - -/* UART Definitions */ -#define CONFIG_BAUDRATE 115200 - -/* Console configuration */ -#define CONFIG_SYS_CBSIZE 1024/* Console buffer size */ -#define CONFIG_SYS_MAXARGS 64 -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#endif
include/configs/owl-common.h new file +40 -0
@@ -0,0 +1,40 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Board configuration file for Actions Semi Owl SoCs. +* +* Copyright (C) 2015 Actions Semi Co., Ltd. +* Copyright (C) 2018 Manivannan Sadhasivam <[email protected]> +* +*/ + +#ifndef _OWL_COMMON_CONFIG_H_ +#define _OWL_COMMON_CONFIG_H_ + +/* SDRAM Definitions */ +#define CONFIG_SYS_SDRAM_BASE 0x0 +#define CONFIG_SYS_SDRAM_SIZE 0x80000000 + +/* Generic Timer Definitions */ +#define COUNTER_FREQUENCY (24000000)/* 24MHz */ + +#define CONFIG_SYS_MALLOC_LEN (32 * 1024 * 1024) + +/* Some commands use this as the default load address */ +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7ffc0) + +/* +* This is the initial SP which is used only briefly for relocating the u-boot +* image to the top of SDRAM. After relocation u-boot moves the stack to the +* proper place. +*/ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + 0x7ff00) + +/* UART Definitions */ +#define CONFIG_BAUDRATE 115200 + +/* Console configuration */ +#define CONFIG_SYS_CBSIZE 1024/* Console buffer size */ +#define CONFIG_SYS_MAXARGS 64 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#endif
include/configs/s900.h new file +16 -0
@@ -0,0 +1,16 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (C) 2015 Actions Semi Co., Ltd. +* Copyright (C) 2018 Manivannan Sadhasivam <[email protected]> +* +*/ + +#ifndef _CONFIG_S900_H_ +#define _CONFIG_S900_H_ + +/* +* Include common owl configuration where most the settings are +*/ +#include <configs/owl-common.h> + +#endif
Signature · 1 line
2.7.4
PATCH v4 2/11 arm: actions: rename sysmap-s900 to sysmap-owl
In reply to Amit Singh TomarNow that memory maps(for both S700 and S900 SoCs) can be managed using a common file, rename sysmap-s900 to sysmap-owl to reflect the same.
---
Changes since v3:
* No changes.
Changes since v2:
* Fixed the commit message and header.
Changes since v1:
* compile sysmap-owl.c against CONFIG_ARM64 now.
--- arch/arm/mach-owl/Makefile | 2 +- arch/arm/mach-owl/sysmap-owl.c | 32 ++++++++++++++++++++++++++++++++ arch/arm/mach-owl/sysmap-s900.c | 32 -------------------------------- 3 files changed, 33 insertions(+), 33 deletions(-) create mode 100644 arch/arm/mach-owl/sysmap-owl.c delete mode 100644 arch/arm/mach-owl/sysmap-s900.c
arch/arm/mach-owl/Makefile +1 -1
@@ -1,4 +1,4 @@ # SPDX-License-Identifier: GPL-2.0+ obj-y += soc.o -obj-y += sysmap-s900.o +obj-$(CONFIG_ARM64) += sysmap-owl.o
arch/arm/mach-owl/sysmap-owl.c new file +32 -0
@@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Memory map for Actions Semi Owl series SoCs. +* +* Copyright (C) 2015 Actions Semi Co., Ltd. +* Copyright (C) 2018 Manivannan Sadhasivam <[email protected]> +*/ + +#include <common.h> +#include <asm/armv8/mmu.h> + +static struct mm_region owl_mem_map[] = { + { + .virt =0x0UL ,/* DDR */ + .phys =0x0UL ,/* DDR */ + .size =0x80000000UL , + .attrs =PTE_BLOCK_MEMTYPE (MT_NORMAL ) | +PTE_BLOCK_INNER_SHARE + }, { + .virt =0xE0000000UL ,/* Peripheral block */ + .phys =0xE0000000UL ,/* Peripheral block */ + .size =0x08000000UL , + .attrs =PTE_BLOCK_MEMTYPE (MT_DEVICE_NGNRNE ) | +PTE_BLOCK_NON_SHARE | +PTE_BLOCK_PXN |PTE_BLOCK_UXN + }, { +/* List terminator */ +0 , + } +}; + +struct mm_region *mem_map = owl_mem_map;
arch/arm/mach-owl/sysmap-s900.c deleted +0 -32
@@ -1,32 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* -* Actions Semi S900 Memory map -* -* Copyright (C) 2015 Actions Semi Co., Ltd. -* Copyright (C) 2018 Manivannan Sadhasivam <[email protected]> -*/ - -#include <common.h> -#include <asm/armv8/mmu.h> - -static struct mm_region s900_mem_map[] = { - { - .virt =0x0UL ,/* DDR */ - .phys =0x0UL ,/* DDR */ - .size =0x80000000UL , - .attrs =PTE_BLOCK_MEMTYPE (MT_NORMAL ) | -PTE_BLOCK_INNER_SHARE - }, { - .virt =0xE0000000UL ,/* Peripheral block */ - .phys =0xE0000000UL ,/* Peripheral block */ - .size =0x08000000UL , - .attrs =PTE_BLOCK_MEMTYPE (MT_DEVICE_NGNRNE ) | -PTE_BLOCK_NON_SHARE | -PTE_BLOCK_PXN |PTE_BLOCK_UXN - }, { -/* List terminator */ -0 , - } -}; - -struct mm_region *mem_map = s900_mem_map;
Signature · 1 line
2.7.4
PATCH v4 3/11 clk: actions: Add common clock driver
In reply to Amit Singh TomarThis patch converts S900 clock driver to something common that can be used for other SoCs, for instance S700(few of clk registers are same).
---
Changes since v3:
* Fixed register spelling.
* Removed the ethernet related clocks.
* Returned -EINVAL instead 0.
Changes since v2:
* Fixed the commit message.
* Checked for the clk->id.
* Added a .data member with SoC type.
* Removed #ifdefs from few places.
Changes since v1:
* Moved CLK and CLK_OWL symbols from defconfig to arch/arm/Kconfig.
--- arch/arm/Kconfig | 2 + arch/arm/include/asm/arch-owl/clk_s900.h | 57 ------------ arch/arm/include/asm/arch-owl/regs_s700.h | 56 ++++++++++++ configs/bubblegum_96_defconfig | 3 - drivers/clk/owl/Kconfig | 8 +- drivers/clk/owl/Makefile | 2 +- drivers/clk/owl/clk_owl.c | 147 ++++++++++++++++++++++++++++++ drivers/clk/owl/clk_owl.h | 65 +++++++++++++ drivers/clk/owl/clk_s900.c | 137 ---------------------------- 9 files changed, 273 insertions(+), 204 deletions(-) delete mode 100644 arch/arm/include/asm/arch-owl/clk_s900.h create mode 100644 arch/arm/include/asm/arch-owl/regs_s700.h create mode 100644 drivers/clk/owl/clk_owl.c create mode 100644 drivers/clk/owl/clk_owl.h delete mode 100644 drivers/clk/owl/clk_s900.c
arch/arm/Kconfig +2 -0
@@ -886,6 +886,8 @@ config ARCH_OWL select DM select DM_SERIAL select OWL_SERIAL + select CLK + select CLK_OWL select OF_CONTROL imply CMD_DM
arch/arm/include/asm/arch-owl/clk_s900.h deleted +0 -57
57 lines not on this page · raw message
arch/arm/include/asm/arch-owl/regs_s700.h new file +56 -0
56 lines not on this page · raw message
configs/bubblegum_96_defconfig +0 -3
@@ -17,6 +17,3 @@ CONFIG_CMD_CACHE=y CONFIG_CMD_TIMER=y CONFIG_DEFAULT_DEVICE_TREE="bubblegum_96" CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_CLK=y -CONFIG_CLK_OWL=y -CONFIG_CLK_S900=y
drivers/clk/owl/Kconfig +2 -6
@@ -3,10 +3,6 @@ config CLK_OWL depends on CLK && ARCH_OWL help Enable support for clock managemet unit present in Actions Semi - OWL SoCs. + Owl series S900/S700 SoCs. + -config CLK_S900 - bool "Actions Semi S900 clock driver" - depends on CLK_OWL && ARM64 - help - Enable support for the clocks in Actions Semi S900 SoC.
drivers/clk/owl/Makefile +1 -1
@@ -1,3 +1,3 @@ # SPDX-License-Identifier: GPL-2.0+ -obj-$(CONFIG_CLK_S900) += clk_s900.o +obj-$(CONFIG_CLK_OWL) += clk_owl.o
drivers/clk/owl/clk_owl.c new file +147 -0
147 lines not on this page · raw message
drivers/clk/owl/clk_owl.h new file +65 -0
65 lines not on this page · raw message
drivers/clk/owl/clk_s900.c deleted +0 -137
137 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v4 3/11 clk: actions: Add common clock driver
Hi,
Quoted 159 lines · Amit Singh Tomar
This patch converts S900 clock driver to something common that can be used for other SoCs, for instance S700(few of clk registers are same).
Signed-off-by Amit Singh Tomar <[email protected]>---
Changes since v3:
* Fixed register spelling.
* Removed the ethernet related clocks.
* Returned-EINVALinstead 0.
Changes since v2:
* Fixed the commit message.
* Checked for theclk->id.
* Added a .data member with SoC type.
* Removed #ifdefs from few places.
Changes since v1:
* Moved CLK andCLK_OWLsymbols from defconfig toarch/arm/Kconfig.--- arch/arm/Kconfig | 2 + arch/arm/include/asm/arch-owl/clk_s900.h | 57 ------------ arch/arm/include/asm/arch-owl/regs_s700.h | 56 ++++++++++++ configs/bubblegum_96_defconfig | 3 - drivers/clk/owl/Kconfig | 8 +- drivers/clk/owl/Makefile | 2 +- drivers/clk/owl/clk_owl.c | 147 ++++++++++++++++++++++++++++++ drivers/clk/owl/clk_owl.h | 65 +++++++++++++ drivers/clk/owl/clk_s900.c | 137 ---------------------------- 9 files changed, 273 insertions(+), 204 deletions(-) delete mode 100644 arch/arm/include/asm/arch-owl/clk_s900.h create mode 100644 arch/arm/include/asm/arch-owl/regs_s700.h create mode 100644 drivers/clk/owl/clk_owl.c create mode 100644 drivers/clk/owl/clk_owl.h delete mode 100644 drivers/clk/owl/clk_s900.carch/arm/Kconfig +2
-0@@ -886,6 +886,8 @@ config ARCH_OWL select DM select DM_SERIAL select OWL_SERIAL + select CLK + select CLK_OWL select OF_CONTROL imply CMD_DMarch/arm/include/asm/arch-owl/clk_s900.h deleted +0
-57@@ -1,57 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* -* Actions Semi S900 Clock Definitions -* -* Copyright (C) 2015 Actions Semi Co., Ltd. -* Copyright (C) 2018 Manivannan Sadhasivam <[email protected]> -* -*/ - -#ifndef _OWL_CLK_S900_H_ -#define _OWL_CLK_S900_H_ - -#include <clk-uclass.h> - -struct owl_clk_priv { -phys_addr_t base; -}; - -/* BUSCLK register definitions */ -#define CMU_PDBGDIV_8 7 -#define CMU_PDBGDIV_SHIFT 26 -#define CMU_PDBGDIV_DIV (CMU_PDBGDIV_8 << CMU_PDBGDIV_SHIFT) -#define CMU_PERDIV_8 7 -#define CMU_PERDIV_SHIFT 20 -#define CMU_PERDIV_DIV (CMU_PERDIV_8 << CMU_PERDIV_SHIFT) -#define CMU_NOCDIV_2 1 -#define CMU_NOCDIV_SHIFT 19 -#define CMU_NOCDIV_DIV (CMU_NOCDIV_2 << CMU_NOCDIV_SHIFT) -#define CMU_DMMCLK_SRC_APLL 2 -#define CMU_DMMCLK_SRC_SHIFT 10 -#define CMU_DMMCLK_SRC (CMU_DMMCLK_SRC_APLL << CMU_DMMCLK_SRC_SHIFT) -#define CMU_APBCLK_DIV BIT(8) -#define CMU_NOCCLK_SRC BIT(7) -#define CMU_AHBCLK_DIV BIT(4) -#define CMU_CORECLK_MASK 3 -#define CMU_CORECLK_CPLL BIT(1) -#define CMU_CORECLK_HOSC BIT(0) - -/* COREPLL register definitions */ -#define CMU_COREPLL_EN BIT(9) -#define CMU_COREPLL_HOSC_EN BIT(8) -#define CMU_COREPLL_OUT (1104 / 24) - -/* DEVPLL register definitions */ -#define CMU_DEVPLL_CLK BIT(12) -#define CMU_DEVPLL_EN BIT(8) -#define CMU_DEVPLL_OUT (660 / 6) - -/* UARTCLK register definitions */ -#define CMU_UARTCLK_SRC_DEVPLL BIT(16) - -/* DEVCLKEN1 register definitions */ -#define CMU_DEVCLKEN1_UART5 BIT(21) - -#define PLL_STABILITY_WAIT_US 50 - -#endif arch/arm/include/asm/arch-owl/regs_s700.h new file +44
-0@@ -0,0 +1,56 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Actions Semi S700 Register Definitions +* +*/ + +#ifndef _OWL_REGS_S700_H_ +#define _OWL_REGS_S700_H_ + +#define CMU_COREPLL (0x0000) +#define CMU_DEVPLL (0x0004) +#define CMU_DDRPLL (0x0008) +#define CMU_NANDPLL (0x000C) +#define CMU_DISPLAYPLL (0x0010) +#define CMU_AUDIOPLL (0x0014) +#define CMU_TVOUTPLL (0x0018) +#define CMU_BUSCLK (0x001C) +#define CMU_SENSORCLK (0x0020) +#define CMU_LCDCLK (0x0024) +#define CMU_DSIPLLCLK (0x0028) +#define CMU_CSICLK (0x002C) +#define CMU_DECLK (0x0030) +#define CMU_SICLK (0x0034) +#define CMU_BUSCLK1 (0x0038) +#define CMU_HDECLK (0x003C) +#define CMU_VDECLK (0x0040) +#define CMU_VCECLK (0x0044) +#define CMU_NANDCCLK (0x004C) +#define CMU_SD0CLK (0x0050) +#define CMU_SD1CLK (0x0054) +#define CMU_SD2CLK (0x0058) +#define CMU_UART0CLK (0x005C) +#define CMU_UART1CLK (0x0060) +#define CMU_UART2CLK (0x0064) +#define CMU_UART3CLK (0x0068) +#define CMU_UART4CLK (0x006C) +#define CMU_UART5CLK (0x0070) +#define CMU_UART6CLK (0x0074) +#define CMU_PWM0CLK (0x0078) +#define CMU_PWM1CLK (0x007C) +#define CMU_PWM2CLK (0x0080) +#define CMU_PWM3CLK (0x0084) +#define CMU_PWM4CLK (0x0088) +#define CMU_PWM5CLK (0x008C)
arch/arm/include/asm/arch-owl/regs_s700.h line 54
Quoted 10 lines
arch/arm/include/asm/arch-owl/regs_s700.h new file +10
-0+#define CMU_GPU3DCLK (0x0090) +#define CMU_CORECTL (0x009C) +#define CMU_DEVCLKEN0 (0x00A0) +#define CMU_DEVCLKEN1 (0x00A4) +#define CMU_DEVRST0 (0x00A8) +#define CMU_DEVRST1 (0x00AC) +#define CMU_USBPLL (0x00B0) +#define CMU_ETHERNETPLL (0x00B4) +#define CMU_CVBSPLL (0x00B8) +#define CMU_SSTSCLK (0x00C0)
Any chance you can remove the parentheses?
Quoted 53 lines
arch/arm/include/asm/arch-owl/regs_s700.h new file +2
-0+ +#endif configs/bubblegum_96_defconfig +0
-3@@ -17,6 +17,3 @@ CONFIG_CMD_CACHE=y CONFIG_CMD_TIMER=y CONFIG_DEFAULT_DEVICE_TREE="bubblegum_96" CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_CLK=y -CONFIG_CLK_OWL=y -CONFIG_CLK_S900=ydrivers/clk/owl/Kconfig +2
-6@@ -3,10 +3,6 @@ config CLK_OWL depends on CLK && ARCH_OWL help Enable support for clock managemet unit present in Actions Semi - OWL SoCs. + Owl series S900/S700 SoCs. + -config CLK_S900 - bool "Actions Semi S900 clock driver" - depends on CLK_OWL && ARM64 - help - Enable support for the clocks in Actions Semi S900 SoC.drivers/clk/owl/Makefile +1
-1@@ -1,3 +1,3 @@ # SPDX-License-Identifier: GPL-2.0+ -obj-$(CONFIG_CLK_S900) += clk_s900.o +obj-$(CONFIG_CLK_OWL) += clk_owl.odrivers/clk/owl/clk_owl.c new file +8
-0@@ -0,0 +1,147 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Common clock driver for Actions Semi SoCs. +* +* Copyright (C) 2015 Actions Semi Co., Ltd. +* Copyright (C) 2018 Manivannan Sadhasivam <[email protected]> +*/ +
drivers/clk/owl/clk_owl.c line 18
Quoted 10 lines
drivers/clk/owl/clk_owl.c new file +10
-0+#include <common.h> +#include <dm.h> +#include "clk_owl.h" +#include <asm/io.h> +#if defined(CONFIG_MACH_S900 ) +#include <asm/arch-owl/regs_s900.h> +#include <dt-bindings/clock/actions,s900-cmu.h> +#elif defined(CONFIG_MACH_S700 ) +#include <asm/arch-owl/regs_s700.h> +#include <dt-bindings/clock/actions,s700-cmu.h>
Both those include files do not exist yet. This breaks bisectability for bubblegum_96.
So I would suggest you remove the s700 lines for now, and change the s900 filename to match the existing one.
Then change CLK_UART<x> to CLOCK_UART<x> below to make it compile.
Please check that bubblegum_96_defconfig still builds after *every* commit.
Once you sync up the binding include file for S900 later on, you should revert those changes back in the same commit.
Quoted 60 lines
drivers/clk/owl/clk_owl.c new file +60
-0+#endif + +void owl_clk_init (struct owl_clk_priv *priv) +{ +u32 bus_clk =0 , core_pll, dev_pll; + +#if defined(CONFIG_MACH_S900 ) +/* Enable ASSIST_PLL */ +setbits_le32 (priv->base +CMU_ASSISTPLL ,BIT (0 )); +udelay (PLL_STABILITY_WAIT_US ); +#endif + +/* Source HOSC to DEV_CLK */ +clrbits_le32 (priv->base +CMU_DEVPLL ,CMU_DEVPLL_CLK ); + +/* Configure BUS_CLK */ + bus_clk |= (CMU_PDBGDIV_DIV |CMU_PERDIV_DIV |CMU_NOCDIV_DIV | +CMU_DMMCLK_SRC |CMU_APBCLK_DIV |CMU_AHBCLK_DIV | +CMU_NOCCLK_SRC |CMU_CORECLK_HOSC ); +writel (bus_clk, priv->base +CMU_BUSCLK ); + +udelay (PLL_STABILITY_WAIT_US ); + +/* Configure CORE_PLL */ + core_pll =readl (priv->base +CMU_COREPLL ); + core_pll |= (CMU_COREPLL_EN |CMU_COREPLL_HOSC_EN |CMU_COREPLL_OUT ); +writel (core_pll, priv->base +CMU_COREPLL ); + +udelay (PLL_STABILITY_WAIT_US ); + +/* Configure DEV_PLL */ + dev_pll =readl (priv->base +CMU_DEVPLL ); + dev_pll |= (CMU_DEVPLL_EN |CMU_DEVPLL_OUT ); +writel (dev_pll, priv->base +CMU_DEVPLL ); + +udelay (PLL_STABILITY_WAIT_US ); + +/* Source CORE_PLL for CORE_CLK */ +clrsetbits_le32 (priv->base +CMU_BUSCLK ,CMU_CORECLK_MASK , +CMU_CORECLK_CPLL ); + +/* Source DEV_PLL for DEV_CLK */ +setbits_le32 (priv->base +CMU_DEVPLL ,CMU_DEVPLL_CLK ); + +udelay (PLL_STABILITY_WAIT_US ); +} + +void owl_uart_clk_enable (struct owl_clk_priv *priv) +{ +if (priv->soc ==S900 ) { +/* Source HOSC for UART5 interface */ +clrbits_le32 (priv->base +CMU_UART5CLK ,CMU_UARTCLK_SRC_DEVPLL ); +/* Enable UART5 interface clock */ +setbits_le32 (priv->base +CMU_DEVCLKEN1 ,CMU_DEVCLKEN1_UART5 ); + }else if (priv->soc ==S700 ) { +/* Source HOSC for UART3 interface */ +clrbits_le32 (priv->base +CMU_UART3CLK ,CMU_UARTCLK_SRC_DEVPLL ); +/* Enable UART3 interface clock */ +setbits_le32 (priv->base +CMU_DEVCLKEN1 ,CMU_DEVCLKEN1_UART3 ); + }
drivers/clk/owl/clk_owl.c line 88
Quoted 10 lines
drivers/clk/owl/clk_owl.c new file +10
-0+} + +int owl_clk_enable (struct clk *clk) +{ +struct owl_clk_priv *priv =dev_get_priv (clk->dev); + +switch (clk->id) { +case CLK_UART5 : +case CLK_UART3 : +owl_uart_clk_enable (priv);
So that's bit weird: Here you join the clocks from both SoCs, just to differentiate them again in the function above.
Why not just merge owl_uart_clk_enable() into this function, something like:
case CLK_UART5: if (priv->soc == S700) return -EINVAL; clrbits(....); setbits(....); break; case CLK_UART3: if (priv->soc == S900) ...
That is much more future-proof and easier to extend later.
drivers/clk/owl/clk_owl.c line 101
Quoted 13 lines
drivers/clk/owl/clk_owl.c new file +13
-0+break ; +default : +return -EINVAL ; + } + +return 0 ; +} + +int owl_clk_disable (struct clk *clk) +{ +struct owl_clk_priv *priv =dev_get_priv (clk->dev); + +if (priv->soc ==S900 ) {
Please use the provided clock ID in a switch/case instead of relying on the UART clock being the only clock ever disabled.
This also saves you the comments.
Quoted 26 lines
drivers/clk/owl/clk_owl.c new file +26
-0+/* Disable UART5 interface clock */ +clrbits_le32 (priv->base +CMU_DEVCLKEN1 ,CMU_DEVCLKEN1_UART5 ); + }else if (priv->soc ==S700 ) { +/* Disable UART3 interface clock */ +clrbits_le32 (priv->base +CMU_DEVCLKEN1 ,CMU_DEVCLKEN1_UART3 ); + } + +return 0 ; +} + +static int owl_clk_probe (struct udevice *dev) +{ +struct owl_clk_priv *priv =dev_get_priv (dev); + + priv->base =dev_read_addr (dev); +if (priv->base ==FDT_ADDR_T_NONE ) +return -EINVAL ; + +/* setup necessary clocks */ +owl_clk_init (priv); + +return 0 ; +} + +static const struct clk_ops owl_clk_ops = { + .enable = owl_clk_enable,
drivers/clk/owl/clk_owl.c line 137
Quoted 10 lines
drivers/clk/owl/clk_owl.c new file +10
-0+ .disable = owl_clk_disable, +}; + +static const struct udevice_id owl_clk_ids[] = { +#if defined(CONFIG_MACH_S900) + { .compatible ="actions,s900-cmu" , .data =S900 }, +#elif defined(CONFIG_MACH_S700) + { .compatible ="actions,s700-cmu" , .data =S700 }, + { } +#endif
The #endif needs to be one line up, otherwise you break S900.
The rest looks OK now in general.
Cheers,
Andre.
Quoted 225 lines
drivers/clk/owl/clk_owl.c new file +10
-0+}; + +U_BOOT_DRIVER (clk_owl) = { + .name ="clk_owl" , + .id =UCLASS_CLK , + .of_match = owl_clk_ids, + .ops = &owl_clk_ops, + .priv_auto_alloc_size =sizeof (struct owl_clk_priv ), + .probe = owl_clk_probe, +};drivers/clk/owl/clk_owl.h new file +65
-0@@ -0,0 +1,65 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Actions Semi SoCs Clock Definitions +* +* Copyright (C) 2015 Actions Semi Co., Ltd. +* Copyright (C) 2018 Manivannan Sadhasivam <[email protected]> +* +*/ + +#ifndef _OWL_CLK_H_ +#define _OWL_CLK_H_ + +#include <clk-uclass.h> + +enum owl_soc { +S700 , +S900 , +}; + +struct owl_clk_priv { +phys_addr_t base; +enum owl_soc soc; +}; + +/* BUSCLK register definitions */ +#define CMU_PDBGDIV_8 7 +#define CMU_PDBGDIV_SHIFT 26 +#define CMU_PDBGDIV_DIV (CMU_PDBGDIV_8 << CMU_PDBGDIV_SHIFT) +#define CMU_PERDIV_8 7 +#define CMU_PERDIV_SHIFT 20 +#define CMU_PERDIV_DIV (CMU_PERDIV_8 << CMU_PERDIV_SHIFT) +#define CMU_NOCDIV_2 1 +#define CMU_NOCDIV_SHIFT 19 +#define CMU_NOCDIV_DIV (CMU_NOCDIV_2 << CMU_NOCDIV_SHIFT) +#define CMU_DMMCLK_SRC_APLL 2 +#define CMU_DMMCLK_SRC_SHIFT 10 +#define CMU_DMMCLK_SRC (CMU_DMMCLK_SRC_APLL << CMU_DMMCLK_SRC_SHIFT) +#define CMU_APBCLK_DIV BIT(8) +#define CMU_NOCCLK_SRC BIT(7) +#define CMU_AHBCLK_DIV BIT(4) +#define CMU_CORECLK_MASK 3 +#define CMU_CORECLK_CPLL BIT(1) +#define CMU_CORECLK_HOSC BIT(0) + +/* COREPLL register definitions */ +#define CMU_COREPLL_EN BIT(9) +#define CMU_COREPLL_HOSC_EN BIT(8) +#define CMU_COREPLL_OUT (1104 / 24) + +/* DEVPLL register definitions */ +#define CMU_DEVPLL_CLK BIT(12) +#define CMU_DEVPLL_EN BIT(8) +#define CMU_DEVPLL_OUT (660 / 6) + +/* UARTCLK register definitions */ +#define CMU_UARTCLK_SRC_DEVPLL BIT(16) + +#define PLL_STABILITY_WAIT_US 50 + +#define CMU_DEVCLKEN1_UART5 BIT(21) +#define CMU_DEVCLKEN1_UART3 BIT(11) + +#define CMU_DEVCLKEN1_ETH_S700 BIT(23) + +#endif drivers/clk/owl/clk_s900.c deleted +0
-137@@ -1,137 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* -* Actions Semi S900 clock driver -* -* Copyright (C) 2015 Actions Semi Co., Ltd. -* Copyright (C) 2018 Manivannan Sadhasivam <[email protected]> -*/ - -#include <common.h> -#include <dm.h> -#include <asm/arch-owl/clk_s900.h> -#include <asm/arch-owl/regs_s900.h> -#include <asm/io.h> - -#include <dt-bindings/clock/s900_cmu.h> - -void owl_clk_init (struct owl_clk_priv *priv) -{ -u32 bus_clk =0 , core_pll, dev_pll; - -/* Enable ASSIST_PLL */ -setbits_le32 (priv->base +CMU_ASSISTPLL ,BIT (0 )); - -udelay (PLL_STABILITY_WAIT_US ); - -/* Source HOSC to DEV_CLK */ -clrbits_le32 (priv->base +CMU_DEVPLL ,CMU_DEVPLL_CLK ); - -/* Configure BUS_CLK */ - bus_clk |= (CMU_PDBGDIV_DIV |CMU_PERDIV_DIV |CMU_NOCDIV_DIV | -CMU_DMMCLK_SRC |CMU_APBCLK_DIV |CMU_AHBCLK_DIV | -CMU_NOCCLK_SRC |CMU_CORECLK_HOSC ); -writel (bus_clk, priv->base +CMU_BUSCLK ); - -udelay (PLL_STABILITY_WAIT_US ); - -/* Configure CORE_PLL */ - core_pll =readl (priv->base +CMU_COREPLL ); - core_pll |= (CMU_COREPLL_EN |CMU_COREPLL_HOSC_EN |CMU_COREPLL_OUT ); -writel (core_pll, priv->base +CMU_COREPLL ); - -udelay (PLL_STABILITY_WAIT_US ); - -/* Configure DEV_PLL */ - dev_pll =readl (priv->base +CMU_DEVPLL ); - dev_pll |= (CMU_DEVPLL_EN |CMU_DEVPLL_OUT ); -writel (dev_pll, priv->base +CMU_DEVPLL ); - -udelay (PLL_STABILITY_WAIT_US ); - -/* Source CORE_PLL for CORE_CLK */ -clrsetbits_le32 (priv->base +CMU_BUSCLK ,CMU_CORECLK_MASK , -CMU_CORECLK_CPLL ); - -/* Source DEV_PLL for DEV_CLK */ -setbits_le32 (priv->base +CMU_DEVPLL ,CMU_DEVPLL_CLK ); - -udelay (PLL_STABILITY_WAIT_US ); -} - -void owl_uart_clk_enable (struct owl_clk_priv *priv) -{ -/* Source HOSC for UART5 interface */ -clrbits_le32 (priv->base +CMU_UART5CLK ,CMU_UARTCLK_SRC_DEVPLL ); - -/* Enable UART5 interface clock */ -setbits_le32 (priv->base +CMU_DEVCLKEN1 ,CMU_DEVCLKEN1_UART5 ); -} - -void owl_uart_clk_disable (struct owl_clk_priv *priv) -{ -/* Disable UART5 interface clock */ -clrbits_le32 (priv->base +CMU_DEVCLKEN1 ,CMU_DEVCLKEN1_UART5 ); -} - -int owl_clk_enable (struct clk *clk) -{ -struct owl_clk_priv *priv =dev_get_priv (clk->dev); - -switch (clk->id) { -case CLOCK_UART5 : -owl_uart_clk_enable (priv); -break ; -default : -return 0 ; - } - -return 0 ; -} - -int owl_clk_disable (struct clk *clk) -{ -struct owl_clk_priv *priv =dev_get_priv (clk->dev); - -switch (clk->id) { -case CLOCK_UART5 : -owl_uart_clk_disable (priv); -break ; -default : -return 0 ; - } - -return 0 ; -} - -static int owl_clk_probe (struct udevice *dev) -{ -struct owl_clk_priv *priv =dev_get_priv (dev); - - priv->base =dev_read_addr (dev); -if (priv->base ==FDT_ADDR_T_NONE ) -return -EINVAL ; - -/* setup necessary clocks */ -owl_clk_init (priv); - -return 0 ; -} - -static struct clk_ops owl_clk_ops = { - .enable = owl_clk_enable, - .disable = owl_clk_disable, -}; - -static const struct udevice_id owl_clk_ids[] = { - { .compatible ="actions,s900-cmu" }, - { } -}; - -U_BOOT_DRIVER (clk_owl) = { - .name ="clk_s900" , - .id =UCLASS_CLK , - .of_match = owl_clk_ids, - .ops = &owl_clk_ops, - .priv_auto_alloc_size =sizeof (struct owl_clk_priv ), - .probe = owl_clk_probe, -};
PATCH v4 3/11 clk: actions: Add common clock driver
Hi,
Quoted 10 lines
Both those include files do not exist yet. This breaks bisectability for
bubblegum_96.
So I would suggest you remove the s700 lines for now, and change the s900 filename to match the existing one.
Then change CLK_UART<x> to CLOCK_UART<x> below to make it compile.Please check that
bubblegum_96_defconfigstill builds after *every* commit.Once you sync up the binding include file for S900 later on, you should revert those changes back in the same commit.
Did you mean, I should first send sync up the binding patches and patch 5/11, then this particular(common
clock driver) patch ?
Thanks
-Amit
PATCH v4 3/11 clk: actions: Add common clock driver
Quoted 8 lines · Amit Tomer
Hi,
Quoted 6 lines
Both those include files do not exist yet. This breaks bisectability for
bubblegum_96.
So I would suggest you remove the s700 lines for now, and change the s900 filename to match the existing one.
Then change CLK_UART<x> to CLOCK_UART<x> below to make it compile.
Quoted 8 lines
Quoted 4 lines
Please check that
bubblegum_96_defconfigstill builds after *every* commit.Once you sync up the binding include file for S900 later on, you should revert those changes back in the same commit.
Did you mean, I should first send sync up the binding patches and patch 5/11, then this particular(common
clock driver) patch ?
There are several ways to solve this problem, I sketched one solution above (which I compile tested), this lets you keep the order.
But I think there are more ordering issues in this series, for instance you introduce S700 support to the build system quite early (04/11), but are not fully ready yet.
Without double checking this, I would suggest:
1, 2, 7, 8, 3, 9, 5, 6, 4, 10, 11. With slight adjustments to 3 like mentioned above.bubblegum_96 must compile cleanly after every patch, and you should not be able to select S700 or Cubie7 until it's ready.
Cheers,
Andre
PATCH v4 4/11 arm: add support Actions Semi S700
In reply to Amit Singh TomarThis patch adds basic support for Actions Semi based S700 SoC, which is driven by common owl framework.
---
Changes since v3:
* Added "SoC" keyword to Actions Semi S700.
Changes since v2:
* Fixed the commit message.
* Checked for the clk->id.
* Added a .data member with SoC type.
* Removed #ifdefs from few places.
Changes since v1:
* Moved CLK and CLK_OWL symbols from defconfig to arch/arm/Kconfig.
--- arch/arm/mach-owl/Kconfig | 6 ++++++ include/configs/s700.h | 13 +++++++++++++ 2 files changed, 19 insertions(+) create mode 100644 include/configs/s700.h
arch/arm/mach-owl/Kconfig +6 -0
@@ -8,6 +8,10 @@ config MACH_S900 bool "Actions Semi S900 SoC" select ARM64 +config MACH_S700 + bool "Actions Semi S700 SoC" + select ARM64 + endchoice config SYS_TEXT_BASE
@@ -15,8 +19,10 @@ config SYS_TEXT_BASE config SYS_CONFIG_NAME default "s900" if MACH_S900 + default "s700" if MACH_S700 config SYS_SOC default "s900" if MACH_S900 + default "s700" if MACH_S700 endif
include/configs/s700.h new file +13 -0
@@ -0,0 +1,13 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +*/ + +#ifndef _CONFIG_S700_H_ +#define _CONFIG_S700_H_ + +/* +* Include common owl configuration where most the settings are +*/ +#include <configs/owl-common.h> + +#endif
Signature · 1 line
2.7.4
PATCH v4 5/11 arm: actions: add S700 SoC device tree
In reply to Amit Singh TomarThis patch adds .dtsi file(sync with Linux 5.5-rc6 with hash "b3a987b") and required binding for S700 SoC that is a 64-bit Quad-core ARM Cortex-A53 cores.
It also provisions DT build based on CONFIG_MACH_S900/S700 symbol instead of CONFIG_ARCH_OWL(this let to build dtb file only for specific board).
---
Changes since v3:
* Updated commit message to the Linux tag to which the dtsi file is synced.
Changes since v2:
* Synced DTS bindings with Linux 5.5.
Changes since v1:
* Moved the u-boot specific changes to s700-u-boot.dtsi, now s700.dtsi is in complete sync with Linux 4.20.
--- arch/arm/dts/Makefile | 6 +- arch/arm/dts/s700.dtsi | 248 +++++++++++++++++++++++++ include/dt-bindings/clock/actions,s700-cmu.h | 118 ++++++++++++ include/dt-bindings/reset/actions,s700-reset.h | 34 ++++ 4 files changed, 404 insertions(+), 2 deletions(-) create mode 100644 arch/arm/dts/s700.dtsi create mode 100644 include/dt-bindings/clock/actions,s700-cmu.h create mode 100644 include/dt-bindings/reset/actions,s700-reset.h
arch/arm/dts/Makefile +4 -2
@@ -64,8 +64,10 @@ dtb-$(CONFIG_KIRKWOOD) += \ kirkwood-pogo_e02.dtb \ kirkwood-sheevaplug.dtb -dtb-$(CONFIG_ARCH_OWL) += \ - bubblegum_96.dtb +dtb-$(CONFIG_MACH_S900) += \ + bubblegum_96.dtb +dtb-$(CONFIG_MACH_S700) += \ + s700-cubieboard7.dtb dtb-$(CONFIG_ROCKCHIP_PX30) += \ px30-evb.dtb \
arch/arm/dts/s700.dtsi new file +248 -0
248 lines not on this page · raw message
include/dt-bindings/clock/actions,s700-cmu.h new file +118 -0
118 lines not on this page · raw message
include/dt-bindings/reset/actions,s700-reset.h new file +34 -0
@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT) +// +// Device Tree binding constants for Actions Semi S700 Reset Management Unit +// +// Copyright (c) 2018 Linaro Ltd. + +#ifndef __DT_BINDINGS_ACTIONS_S700_RESET_H +#define __DT_BINDINGS_ACTIONS_S700_RESET_H + +#define RESET_AUDIO 0 +#define RESET_CSI 1 +#define RESET_DE 2 +#define RESET_DSI 3 +#define RESET_GPIO 4 +#define RESET_I2C0 5 +#define RESET_I2C1 6 +#define RESET_I2C2 7 +#define RESET_I2C3 8 +#define RESET_KEY 9 +#define RESET_LCD0 10 +#define RESET_SI 11 +#define RESET_SPI0 12 +#define RESET_SPI1 13 +#define RESET_SPI2 14 +#define RESET_SPI3 15 +#define RESET_UART0 16 +#define RESET_UART1 17 +#define RESET_UART2 18 +#define RESET_UART3 19 +#define RESET_UART4 20 +#define RESET_UART5 21 +#define RESET_UART6 22 + +#endif /* __DT_BINDINGS_ACTIONS_S700_RESET_H */
Signature · 1 line
2.7.4
PATCH v4 6/11 arm: dts: actions: s700: add u-boot specific dtsi file
In reply to Amit Singh TomarDevices like uart and clk are needed to be enabled before relocation. this patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
---
Changes since v3:
* Replaced dtsi with dts in subject line along with arm:dts:
to the prefix.
Changes since v2:
* Added License.
Changes since v1:
* This is newly added file that was *not* present in v1 and contains u-boot specific changes.
--- arch/arm/dts/s700-u-boot.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) create mode 100644 arch/arm/dts/s700-u-boot.dtsi
arch/arm/dts/s700-u-boot.dtsi new file +18 -0
@@ -0,0 +1,18 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Amit Singh Tomar <[email protected]> + */ + +/{ + soc { + u-boot,dm-pre-reloc; + }; +}; + +&uart3 { + u-boot,dm-pre-reloc; +}; + +&cmu { + u-boot,dm-pre-reloc; +};
Signature · 1 line
2.7.4
PATCH v4 7/11 arm: dts: sync dts for Action Semi S900
In reply to Amit Singh TomarSynchronize device tree bindings with v5.5-rc6 tag with commit id "b3a987b".
Also, it removes older clock binding defined for S900.
---
Changes since v3:
* Added Reviewed-by: tag.
Changes since v2:
* Newly added patch, not there in v2/v1.
--- arch/arm/dts/s900.dtsi | 322 +++++++++++++++++++++++-- include/dt-bindings/clock/actions,s900-cmu.h | 129 ++++++++++ include/dt-bindings/clock/s900_cmu.h | 77 ------ include/dt-bindings/reset/actions,s900-reset.h | 65 +++++ 4 files changed, 495 insertions(+), 98 deletions(-) create mode 100644 include/dt-bindings/clock/actions,s900-cmu.h delete mode 100644 include/dt-bindings/clock/s900_cmu.h create mode 100644 include/dt-bindings/reset/actions,s900-reset.h
arch/arm/dts/s900.dtsi +301 -21
@@ -1,17 +1,94 @@ -// SPDX-License-Identifier: GPL-2.0+ -// -// Device Tree Source for Actions Semi S900 SoC -// -// Copyright (C) 2015 Actions Semi Co., Ltd. -// Copyright (C) 2018 Manivannan Sadhasivam <[email protected]> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2017 Andreas F?rber + */ -/dts-v1/; -#include <dt-bindings/clock/s900_cmu.h> +#include <dt-bindings/clock/actions,s900-cmu.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/reset/actions,s900-reset.h> / { compatible = "actions,s900"; - #address-cells = <0x2>; - #size-cells = <0x2>; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu0: cpu at 0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0 0x0>; + enable-method = "psci"; + }; + + cpu1: cpu at 1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0 0x1>; + enable-method = "psci"; + }; + + cpu2: cpu at 2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0 0x2>; + enable-method = "psci"; + }; + + cpu3: cpu at 3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0 0x3>; + enable-method = "psci"; + }; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + secmon at 1f000000 { + reg = <0x0 0x1f000000 0x0 0x1000000>; + no-map; + }; + }; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + arm-pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; + + hosc: hosc { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + #clock-cells = <0>; + }; losc: losc { compatible = "fixed-clock";
@@ -26,28 +103,231 @@ }; soc { - u-boot,dm-pre-reloc; compatible = "simple-bus"; - #address-cells = <0x2>; - #size-cells = <0x2>; + #address-cells = <2>; + #size-cells = <2>; ranges; + gic: interrupt-controller at e00f1000 { + compatible = "arm,gic-400"; + reg = <0x0 0xe00f1000 0x0 0x1000>, + <0x0 0xe00f2000 0x0 0x2000>, + <0x0 0xe00f4000 0x0 0x2000>, + <0x0 0xe00f6000 0x0 0x2000>; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + interrupt-controller; + #interrupt-cells = <3>; + }; + + uart0: serial at e0120000 { + compatible = "actions,s900-uart", "actions,owl-uart"; + reg = <0x0 0xe0120000 0x0 0x2000>; + clocks = <&cmu CLK_UART0>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart1: serial at e0122000 { + compatible = "actions,s900-uart", "actions,owl-uart"; + reg = <0x0 0xe0122000 0x0 0x2000>; + clocks = <&cmu CLK_UART1>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart2: serial at e0124000 { + compatible = "actions,s900-uart", "actions,owl-uart"; + reg = <0x0 0xe0124000 0x0 0x2000>; + clocks = <&cmu CLK_UART2>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart3: serial at e0126000 { + compatible = "actions,s900-uart", "actions,owl-uart"; + reg = <0x0 0xe0126000 0x0 0x2000>; + clocks = <&cmu CLK_UART3>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart4: serial at e0128000 { + compatible = "actions,s900-uart", "actions,owl-uart"; + reg = <0x0 0xe0128000 0x0 0x2000>; + clocks = <&cmu CLK_UART4>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + uart5: serial at e012a000 { - u-boot,dm-pre-reloc; - compatible = "actions,s900-serial"; - reg = <0x0 0xe012a000 0x0 0x1000>; - clocks = <&cmu CLOCK_UART5>; + compatible = "actions,s900-uart", "actions,owl-uart"; + reg = <0x0 0xe012a000 0x0 0x2000>; + clocks = <&cmu CLK_UART5>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; + uart6: serial at e012c000 { + compatible = "actions,s900-uart", "actions,owl-uart"; + reg = <0x0 0xe012c000 0x0 0x2000>; + clocks = <&cmu CLK_UART6>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + sps: power-controller at e012e000 { + compatible = "actions,s900-sps"; + reg = <0x0 0xe012e000 0x0 0x2000>; + #power-domain-cells = <1>; + }; + cmu: clock-controller at e0160000 { - u-boot,dm-pre-reloc; compatible = "actions,s900-cmu"; reg = <0x0 0xe0160000 0x0 0x1000>; - clocks = <&losc>, <&diff24M>; - clock-names = "losc", "diff24M"; + clocks = <&hosc>, <&losc>; #clock-cells = <1>; + #reset-cells = <1>; + }; + + i2c0: i2c at e0170000 { + compatible = "actions,s900-i2c"; + reg = <0 0xe0170000 0 0x1000>; + clocks = <&cmu CLK_I2C0>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c at e0172000 { + compatible = "actions,s900-i2c"; + reg = <0 0xe0172000 0 0x1000>; + clocks = <&cmu CLK_I2C1>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c at e0174000 { + compatible = "actions,s900-i2c"; + reg = <0 0xe0174000 0 0x1000>; + clocks = <&cmu CLK_I2C2>; + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c at e0176000 { + compatible = "actions,s900-i2c"; + reg = <0 0xe0176000 0 0x1000>; + clocks = <&cmu CLK_I2C3>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c4: i2c at e0178000 { + compatible = "actions,s900-i2c"; + reg = <0 0xe0178000 0 0x1000>; + clocks = <&cmu CLK_I2C4>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c5: i2c at e017a000 { + compatible = "actions,s900-i2c"; + reg = <0 0xe017a000 0 0x1000>; + clocks = <&cmu CLK_I2C5>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + pinctrl: pinctrl at e01b0000 { + compatible = "actions,s900-pinctrl"; + reg = <0x0 0xe01b0000 0x0 0x1000>; + clocks = <&cmu CLK_GPIO>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 146>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer: timer at e0228000 { + compatible = "actions,s900-timer"; + reg = <0x0 0xe0228000 0x0 0x8000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "timer1"; + }; + + dma: dma-controller at e0260000 { + compatible = "actions,s900-dma"; + reg = <0x0 0xe0260000 0x0 0x1000>; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + dma-channels = <12>; + dma-requests = <46>; + clocks = <&cmu CLK_DMAC>; + }; + + mmc0: mmc at e0330000 { + compatible = "actions,owl-mmc"; + reg = <0x0 0xe0330000 0x0 0x4000>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_SD0>; + resets = <&cmu RESET_SD0>; + dmas = <&dma 2>; + dma-names = "mmc"; + status = "disabled"; + }; + + mmc1: mmc at e0334000 { + compatible = "actions,owl-mmc"; + reg = <0x0 0xe0334000 0x0 0x4000>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_SD1>; + resets = <&cmu RESET_SD1>; + dmas = <&dma 3>; + dma-names = "mmc"; + status = "disabled"; + }; + + mmc2: mmc at e0338000 { + compatible = "actions,owl-mmc"; + reg = <0x0 0xe0338000 0x0 0x4000>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_SD2>; + resets = <&cmu RESET_SD2>; + dmas = <&dma 4>; + dma-names = "mmc"; + status = "disabled"; + }; + + mmc3: mmc at e033c000 { + compatible = "actions,owl-mmc"; + reg = <0x0 0xe033c000 0x0 0x4000>; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_SD3>; + resets = <&cmu RESET_SD3>; + dmas = <&dma 46>; + dma-names = "mmc"; + status = "disabled"; }; }; }; -
include/dt-bindings/clock/actions,s900-cmu.h new file +129 -0
129 lines not on this page · raw message
include/dt-bindings/clock/s900_cmu.h deleted +0 -77
77 lines not on this page · raw message
include/dt-bindings/reset/actions,s900-reset.h new file +65 -0
65 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v4 8/11 arm: dts: actions: s900: add u-boot specific dtsi file
In reply to Amit Singh TomarDevices like uart and clk are needed to be enabled before relocation. This patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
---
Changes since v3:
* Replaced dtsi with dts in subject line along with arm:dts:
to the prefix.
Changes since v2:
* Newly added patch, not there in v2/v1.
--- arch/arm/dts/s900-u-boot.dtsi | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) create mode 100644 arch/arm/dts/s900-u-boot.dtsi
arch/arm/dts/s900-u-boot.dtsi new file +17 -0
@@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + */ + +/{ + soc { + u-boot,dm-pre-reloc; + }; +}; + +&uart5 { + u-boot,dm-pre-reloc; +}; + +&cmu { + u-boot,dm-pre-reloc; +};
Signature · 1 line
2.7.4
PATCH v4 9/11 serial: actions: add uart support for s700
In reply to Amit Singh TomarUART controller present on S700 is compatible with existing S900 controller, this patch simply adds a proper compatible string so that owl uart driver can be reused for S700.
---
Changes since v3:
* Used only owl-uart for compatible string.
Changes since v2:
* No changes.
Changes since v1:
* No changes.
--- drivers/serial/serial_owl.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/serial/serial_owl.c +1 -1
@@ -120,7 +120,7 @@ static const struct dm_serial_ops owl_serial_ops = { };static const struct udevice_id owl_serial_ids[] = { - { .compatible ="actions,s900-serial" }, + { .compatible ="actions,owl-uart" }, { } };
Signature · 1 line
2.7.4
PATCH v4 10/11 arm: add Cubieboard7 board support
In reply to Amit Singh TomarThe Cubieboard is a single board computer containing a Actions S700 SoC(with 4 ARMv8 Cortex-A53 cores).
This patch adds respective defconfig alongwith device tree(sync with Linux v5.5-rc6).
---
Changes since v3:
* added reviewed-by: tag.
Changes since v2:
* No changes.
Changes since v1:
* No changes.
--- arch/arm/dts/s700-cubieboard7.dts | 92 +++++++++++++++++++++++++++++++++++++++ configs/cubieboard7_defconfig | 16 +++++++ 2 files changed, 108 insertions(+) create mode 100644 arch/arm/dts/s700-cubieboard7.dts create mode 100644 configs/cubieboard7_defconfig
arch/arm/dts/s700-cubieboard7.dts new file +92 -0
@@ -0,0 +1,92 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2017 Andreas F?rber + */ + +/dts-v1/; + +#include "s700.dtsi" + +/ { + compatible = "cubietech,cubieboard7", "actions,s700"; + model = "CubieBoard7"; + + aliases { + serial3 = &uart3; + }; + + chosen { + stdout-path = "serial3:115200n8"; + }; + + memory at 0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + memory at 1,e0000000 { + device_type = "memory"; + reg = <0x1 0xe0000000 0x0 0x0>; + }; +}; + +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_default>; +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_default>; +}; + +&i2c2 { + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_default>; +}; + +&pinctrl { + i2c0_default: i2c0_default { + pinmux { + groups = "i2c0_mfp"; + function = "i2c0"; + }; + pinconf { + pins = "i2c0_sclk", "i2c0_sdata"; + bias-pull-up; + }; + }; + + i2c1_default: i2c1_default { + pinmux { + groups = "i2c1_dummy"; + function = "i2c1"; + }; + pinconf { + pins = "i2c1_sclk", "i2c1_sdata"; + bias-pull-up; + }; + }; + + i2c2_default: i2c2_default { + pinmux { + groups = "i2c2_dummy"; + function = "i2c2"; + }; + pinconf { + pins = "i2c2_sclk", "i2c2_sdata"; + bias-pull-up; + }; + }; +}; + +&timer { + clocks = <&hosc>; +}; + +&uart3 { + status = "okay"; +};
configs/cubieboard7_defconfig new file +16 -0
@@ -0,0 +1,16 @@ +CONFIG_ARM=y +CONFIG_ARCH_OWL=y +CONFIG_MACH_S700=y +CONFIG_IDENT_STRING="\ncubieboard7" +CONFIG_DISTRO_DEFAULTS=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_BOOTDELAY=5 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyOWL3,115200n8" +# CONFIG_DISPLAY_CPUINFO is not set +# CONFIG_DISPLAY_BOARDINFO is not set +CONFIG_SYS_PROMPT="U-Boot => " +CONFIG_CMD_MD5SUM=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_TIMER=y +CONFIG_DEFAULT_DEVICE_TREE="s700-cubieboard7"
Signature · 1 line
2.7.4
PATCH v4 11/11 doc: boards: add Cubieboard7 documentation
In reply to Amit Singh TomarThis adds build and flash steps for Actions S700
based Cubieboard7 board.
---
Changes since v3:
* Convert plain text documentation to reStructuredText format.
Changes since v2:
* No Change.
Changes since v1:
* No Change.
--- doc/board/actions/cubieboard7.rst | 115 ++++++++++++++++++++++++++++++++++++++ doc/board/actions/index.rst | 10 ++++ doc/board/index.rst | 1 + 3 files changed, 126 insertions(+) create mode 100644 doc/board/actions/cubieboard7.rst create mode 100644 doc/board/actions/index.rst
doc/board/actions/cubieboard7.rst new file +115 -0
@@ -0,0 +1,115 @@ +.. SPDX-License-Identifier: GPL-2.0+ +.. Copyright (C) 2020 Amit Singh Tomar <[email protected]> + +ACTIONS +======== + +About this +---------- + +This document describes build and flash steps for Actions S700 SoC based Cubieboard7 +board. + +Cubieboard7 initial configuration +--------------------------------- + +Default Cubieboard7 comes with pre-installed Android where U-Boot is configured with +a bootdelay of 0, entering a prompt by pressing keys does not seem to work. + +Though, one can enter ADFU mode and flash debian image(from host machine) where +getting into u-boot prompt is easy. + +Enter ADFU Mode +---------------- + +Before write the firmware, let the development board entering the ADFU mode: insert +one end of the USB cable to the PC, press and hold the ADFU button, and then connect +the other end of the USB cable to the Mini USB port of the development board, release +the ADFU button, after connecting it will enter the ADFU mode. + +Check whether entered ADFU Mode +-------------------------------- + +The user needs to run the following command on the PC side to check if the ADFU +device is detected. ID realted to "Actions Semiconductor Co., Ltd" means that +the PC side has been correctly detected ADFU device, the development board +also enter into the ADFU mode. + +.. code-block:: none + + $ lsusb + Bus 001 Device 005: ID 04f2:b2eb Chicony Electronics Co., Ltd + Bus 001 Device 004: ID 0a5c:21e6 Broadcom Corp. BCM20702 Bluetooth 4.0 [ThinkPad] + Bus 001 Device 003: ID 046d:c534 Logitech, Inc. Unifying Receiver + Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub + Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub + Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub + Bus 003 Device 013: ID 10d6:10d6 Actions Semiconductor Co., Ltd + Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub + +Flashing debian image +--------------------- + +.. code-block:: none + + $ sudo ./ActionsFWU.py --fw=debian-stretch-desktop-cb7-emmc-v2.0.fw + ActionsFWU.py : 1.0.150828.0830 + libScript.so : 2.3.150825.0951 + libFileSystem.so: 2.3.150825.0952 + libProduction.so: 2.3.150915.1527 + =====burn all partition==== + FW_VER: 3.10.37.180608 + 3% DOWNLOAD ADFUDEC ... + 5% DOWNLOAD BOOT PARA ... + 7% SWITCH ADFUDEC ... + 12% DOWNLOAD BL31 ... + 13% DOWNLOAD BL32 ... + 15% DOWNLOAD VMLINUX ... + 20% DOWNLOAD INITRD ... + 24% DOWNLOAD FDT ... + 27% DOWNLOAD ADFUS ... + 30% SWITCH ADFUS ... + 32% DOWNLOAD MBR ... + 35% DOWNLOAD PARTITIONS ... + WRITE_MBRC_PARTITION + 35% write p0 size = 2048 : ok + WRITE_BOOT_PARTITION + 35% write p1 size = 2048 : ok + WRITE_MISC_PARTITION + 36% write p2 size = 98304 : ok + WRITE_SYSTEM_PARTITION + 94% write p3 size = 4608000 : ok + FORMAT_SWAP_PARTITION + 94% write p4 size = 20480 : ok + 95% TRANSFER OVER ... + Firmware upgrade successfully! + +Debian image can be downloaded from here[1]. + +Once debian image is flashed, one can get into u-boot prompt by pressing any key and from +there run ums command(make sure, usb cable is connected between host and target): + +.. code-block:: none + + owl> ums 0 mmc 1 + +Above command would mount debian image partition on host machine. + +Building U-BOOT proper image +---------------------------- + +.. code-block:: none + + $ make clean + $ export CROSS_COMPILE=aarch64-linux-gnu- + $ make ARCH=arm cubieboard7_defconfig + $ make -j16 + $ mkimage -A arm -T firmware -C none -O u-boot -a 0x11000000 -e 0x11000000 -d u-boot-dtb.bin u-boot-dtb.img >/dev/null + +u-boot-dtb.img can now be flashed to debian image partition mounted on host machine. + +.. code-block:: none + + $ sudo dd if=u-boot-dtb.img of=/dev/sdb bs=1024 seek=3072 + +[1]: https://pan.baidu.com/s/1uawPr0Jao2HgWFLZCLzHAg#list/path=%2FCubieBoard_Download%2FBoard%2FCubieBoard7%2F%E6%96%B9%E7%B3%96%E6%96%B9%E6%A1%88%E5%BC%80%E5%8F%91%E8%B5%84%E6%96%99%2FImage%2FDebian%2FV2.1-test&parentPath=%2F
doc/board/actions/index.rst new file +10 -0
@@ -0,0 +1,10 @@ +.. SPDX-License-Identifier: GPL-2.0+ +.. Copyright (C) 2020 Amit Singh Tomar <[email protected]> + +Actions +======== + +.. toctree:: + :maxdepth: 2 + + cubieboard7
doc/board/index.rst +1 -0
@@ -6,6 +6,7 @@ Board-specific doc .. toctree:: :maxdepth: 2 + actions/index AndesTech/index atmel/index coreboot/index
Signature · 1 line
2.7.4