Skip to contentSkip to conversation

Add APSS clock controller support for IPQ6018

PATCH Superseded Sivaprakash Murugesan 2 participants 10 messages Apr 5, 2020 – Apr 9, 2020

Subsystems (6)

v2 of 8 Superseded Latest is v8 →

lore
Share & tools
lore
#0 lore raw

v2 cover Add APSS clock controller support for IPQ6018

The CPU on Qualcomm's IPQ6018 devices are primarily fed by A53 PLL and XO, these are connected to a clock mux and enable block.

This patch series adds support for these clocks and inturn enables clocks required for CPU freq.

[V2]
* Restructred the patch series as there are two different HW blocks, the mux and enable belongs to the apcs block and PLL has a separate HW block.
* Converted qcom mailbox and qcom a53 pll documentation to yaml.
* Addressed review comments from Stephen, Rob and Sibi where it is applicable.
* Changed this cover letter to state the purpose of this patch series

Sivaprakash Murugesan (8):
dt-bindings: mailbox: Add YAML schemas for QCOM APCS global block
dt-bindings: clock: Add YAML schemas for QCOM A53 PLL
clk: qcom: Add A53 PLL support for ipq6018 devices
clk: qcom: Add DT bindings for ipq6018 apss clock controller
clk: qcom: Add ipq apss clock controller
dt-bindings: mailbox: Add dt-bindings for ipq6018 apcs global block
mailbox: qcom: Add ipq6018 apcs compatible
arm64: dts: ipq6018: Add a53 pll and apcs clock

 .../devicetree/bindings/clock/qcom,a53pll.txt      |  22 ----
 .../devicetree/bindings/clock/qcom,a53pll.yaml     |  60 +++++++++
 .../bindings/mailbox/qcom,apcs-kpss-global.txt     |  88 -------------
 .../bindings/mailbox/qcom,apcs-kpss-global.yaml    | 101 +++++++++++++++
 arch/arm64/boot/dts/qcom/ipq6018.dtsi              |  16 ++-
 drivers/clk/qcom/Kconfig                           |  10 ++
 drivers/clk/qcom/Makefile                          |   1 +
 drivers/clk/qcom/a53-pll.c                         | 136 +++++++++++++++++----
 drivers/clk/qcom/apss-ipq.c                        | 107 ++++++++++++++++
 drivers/mailbox/qcom-apcs-ipc-mailbox.c            |  22 ++--
 include/dt-bindings/clock/qcom,apss-ipq.h          |  12 ++
 11 files changed, 430 insertions(+), 145 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/clock/qcom,a53pll.txt
 create mode 100644 Documentation/devicetree/bindings/clock/qcom,a53pll.yaml
 delete mode 100644 Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt
 create mode 100644 Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.yaml
 create mode 100644 drivers/clk/qcom/apss-ipq.c
 create mode 100644 include/dt-bindings/clock/qcom,apss-ipq.h
Signature · 1 line
2.7.4
#1 lore raw

PATCH v2 1/8 dt-bindings: mailbox: Add YAML schemas for QCOM APCS global block

Qualcomm APCS global block provides a bunch of generic properties which are required in a device tree. Add YAML schema for these properties.

---
 .../bindings/mailbox/qcom,apcs-kpss-global.txt     | 88 ----------------------
 .../bindings/mailbox/qcom,apcs-kpss-global.yaml    | 88 ++++++++++++++++++++++
 2 files changed, 88 insertions(+), 88 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt
 create mode 100644 Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.yaml
Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt deleted +0 -88
deleted file mode 100644
index beec612..0000000
@@ -1,88 +0,0 @@
-Binding for the Qualcomm APCS global block
-==========================================
-
-This binding describes the APCS "global" block found in various Qualcomm
-platforms.
-
-- compatible:
-	Usage: required
-	Value type: <string>
-	Definition: must be one of:
-		    "qcom,msm8916-apcs-kpss-global",
-		    "qcom,msm8996-apcs-hmss-global"
-		    "qcom,msm8998-apcs-hmss-global"
-		    "qcom,qcs404-apcs-apps-global"
-		    "qcom,sc7180-apss-shared"
-		    "qcom,sdm845-apss-shared"
-		    "qcom,sm8150-apss-shared"
-		    "qcom,ipq8074-apcs-apps-global"
-
-- reg:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: must specify the base address and size of the global block
-
-- clocks:
-	Usage: required if #clock-names property is present
-	Value type: <phandle array>
-	Definition: phandles to the two parent clocks of the clock driver.
-
-- #mbox-cells:
-	Usage: required
-	Value type: <u32>
-	Definition: as described in mailbox.txt, must be 1
-
-- #clock-cells:
-	Usage: optional
-	Value type: <u32>
-	Definition: as described in clock.txt, must be 0
-
-- clock-names:
-	Usage: required if the platform data based clock driver needs to
-	retrieve the parent clock names from device tree.
-	This will requires two mandatory clocks to be defined.
-	Value type: <string-array>
-	Definition: must be "pll" and "aux"
-
-= EXAMPLE
-The following example describes the APCS HMSS found in MSM8996 and part of the
-GLINK RPM referencing the "rpm_hlos" doorbell therein.
-
-	apcs_glb: mailbox@9820000 {
-		compatible = "qcom,msm8996-apcs-hmss-global";
-		reg = <0x9820000 0x1000>;
-
-		#mbox-cells = <1>;
-	};
-
-	rpm-glink {
-		compatible = "qcom,glink-rpm";
-
-		interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
-
-		qcom,rpm-msg-ram = <&rpm_msg_ram>;
-
-		mboxes = <&apcs_glb 0>;
-		mbox-names = "rpm_hlos";
-	};
-
-Below is another example of the APCS binding on MSM8916 platforms:
-
-	apcs: mailbox@b011000 {
-		compatible = "qcom,msm8916-apcs-kpss-global";
-		reg = <0xb011000 0x1000>;
-		#mbox-cells = <1>;
-		clocks = <&a53pll>;
-		#clock-cells = <0>;
-	};
-
-Below is another example of the APCS binding on QCS404 platforms:
-
-	apcs_glb: mailbox@b011000 {
-		compatible = "qcom,qcs404-apcs-apps-global", "syscon";
-		reg = <0x0b011000 0x1000>;
-		#mbox-cells = <1>;
-		clocks = <&apcs_hfpll>, <&gcc GCC_GPLL0_AO_OUT_MAIN>;
-		clock-names = "pll", "aux";
-		#clock-cells = <0>;
-	};
Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.yaml new file +88 -0

88 lines not on this page · raw message

Signature · 1 line
2.7.4
#2 lore raw

PATCH v2 2/8 dt-bindings: clock: Add YAML schemas for QCOM A53 PLL

In reply to Sivaprakash Murugesan

This patch adds schema for primary CPU PLL found on few Qualcomm platforms.

---
 .../devicetree/bindings/clock/qcom,a53pll.txt      | 22 --------
 .../devicetree/bindings/clock/qcom,a53pll.yaml     | 60 ++++++++++++++++++++++
 2 files changed, 60 insertions(+), 22 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/clock/qcom,a53pll.txt
 create mode 100644 Documentation/devicetree/bindings/clock/qcom,a53pll.yaml
Documentation/devicetree/bindings/clock/qcom,a53pll.txt deleted +0 -22
deleted file mode 100644
index e3fa811..0000000
@@ -1,22 +0,0 @@
-Qualcomm MSM8916 A53 PLL Binding
---------------------------------
-The A53 PLL on MSM8916 platforms is the main CPU PLL used used for frequencies
-above 1GHz.
-
-Required properties :
-- compatible : Shall contain only one of the following:
-
-		"qcom,msm8916-a53pll"
-
-- reg : shall contain base register location and length
-
-- #clock-cells : must be set to <0>
-
-Example:
-
-	a53pll: clock@b016000 {
-		compatible = "qcom,msm8916-a53pll";
-		reg = <0xb016000 0x40>;
-		#clock-cells = <0>;
-	};
-
Documentation/devicetree/bindings/clock/qcom,a53pll.yaml new file +60 -0

60 lines not on this page · raw message

Signature · 1 line
2.7.4
maintainer
#3 lore raw

Re: [PATCH V2 2/8] dt-bindings: clock: Add YAML schemas for QCOM A53 PLL

Quoted 11 lines · Sivaprakash Murugesan

This patch adds schema for primary CPU PLL found on few Qualcomm platforms.

---
 .../devicetree/bindings/clock/qcom,a53pll.txt      | 22 --------
 .../devicetree/bindings/clock/qcom,a53pll.yaml     | 60 ++++++++++++++++++++++
 2 files changed, 60 insertions(+), 22 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/clock/qcom,a53pll.txt
 create mode 100644 Documentation/devicetree/bindings/clock/qcom,a53pll.yaml

My bot found errors running 'make dt_binding_check' on your patch:

Documentation/devicetree/bindings/clock/qcom,a53pll.yaml: $id: relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/clock/qcom,a53pll.yaml#

See https://patchwork.ozlabs.org/patch/1266526

If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure dt-schema is up to date:

pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade

Please check and re-submit.

#4 lore raw

PATCH v2 3/8 clk: qcom: Add A53 PLL support for ipq6018 devices

In reply to Sivaprakash Murugesan

The CPUs on Qualcomm IPQ6018 platform is primarily clocked by A53 PLL. This patch adds support for the A53 PLL on IPQ6018 devices which can support CPU frequencies above 1Ghz.

---
 drivers/clk/qcom/a53-pll.c | 136 ++++++++++++++++++++++++++++++++++++---------
 1 file changed, 111 insertions(+), 25 deletions(-)
drivers/clk/qcom/a53-pll.c +111 -25
index 45cfc57..a95351c 100644
@@ -11,11 +11,40 @@
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 
 #include "clk-pll.h"
 #include "clk-regmap.h"
+#include "clk-alpha-pll.h"
 
-static const struct pll_freq_tbl a53pll_freq[] = {
+struct a53_alpha_pll {
+	struct alpha_pll_config *pll_config;
+	struct clk_alpha_pll *pll;
+};
+
+union a53pll {
+	struct clk_pll *pll;
+	struct a53_alpha_pll alpha_pll;
+};
+
+struct a53pll_data {
+#define PLL_IS_ALPHA BIT(0)
+	u8 flags;
+	union a53pll a53pll;
+};
+
+static const u8 ipq_pll_offsets[] = {
+	[PLL_OFF_L_VAL] = 0x08,
+	[PLL_OFF_ALPHA_VAL] = 0x10,
+	[PLL_OFF_USER_CTL] = 0x18,
+	[PLL_OFF_CONFIG_CTL] = 0x20,
+	[PLL_OFF_CONFIG_CTL_U] = 0x24,
+	[PLL_OFF_STATUS] = 0x28,
+	[PLL_OFF_TEST_CTL] = 0x30,
+	[PLL_OFF_TEST_CTL_U] = 0x34,
+};
+
+static const struct pll_freq_tbl msm8996_a53pll_freq[] = {
 	{  998400000, 52, 0x0, 0x1, 0 },
 	{ 1094400000, 57, 0x0, 0x1, 0 },
 	{ 1152000000, 62, 0x0, 0x1, 0 },
@@ -26,6 +55,64 @@ static const struct pll_freq_tbl a53pll_freq[] = {
 	{ }
 };
 
+static struct clk_pll msm8996_pll = {
+	.mode_reg = 0x0,
+	.l_reg = 0x04,
+	.m_reg = 0x08,
+	.n_reg = 0x0c,
+	.config_reg = 0x14,
+	.status_reg = 0x1c,
+	.status_bit = 16,
+	.freq_tbl = msm8996_a53pll_freq,
+	.clkr.hw.init = &(struct clk_init_data){
+		.name = "a53pll",
+		.flags = CLK_IS_CRITICAL,
+		.parent_data = &(const struct clk_parent_data){
+			.fw_name = "xo",
+			.name = "xo",
+		},
+		.num_parents = 1,
+		.ops = &clk_pll_sr2_ops,
+	},
+};
+
+static struct clk_alpha_pll ipq6018_pll = {
+	.offset = 0x0,
+	.regs = ipq_pll_offsets,
+	.flags = SUPPORTS_DYNAMIC_UPDATE,
+	.clkr = {
+		.enable_reg = 0x0,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "a53pll",
+			.flags = CLK_IS_CRITICAL,
+			.parent_data = &(const struct clk_parent_data){
+				.fw_name = "xo",
+			},
+			.num_parents = 1,
+			.ops = &clk_alpha_pll_huayra_ops,
+		},
+	},
+};
+
+static struct alpha_pll_config ipq6018_pll_config = {
+	.l = 0x37,
+	.config_ctl_val = 0x04141200,
+	.config_ctl_hi_val = 0x0,
+	.early_output_mask = BIT(3),
+	.main_output_mask = BIT(0),
+};
+
+static struct a53pll_data msm8996pll_data = {
+	.a53pll.pll = &msm8996_pll,
+};
+
+static struct a53pll_data ipq6018pll_data = {
+	.flags = PLL_IS_ALPHA,
+	.a53pll.alpha_pll.pll = &ipq6018_pll,
+	.a53pll.alpha_pll.pll_config = &ipq6018_pll_config,
+};
+
 static const struct regmap_config a53pll_regmap_config = {
 	.reg_bits		= 32,
 	.reg_stride		= 4,
@@ -39,14 +126,16 @@ static int qcom_a53pll_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct regmap *regmap;
 	struct resource *res;
-	struct clk_pll *pll;
+	const struct a53pll_data *pll_data;
+	struct clk_regmap *clkr;
 	void __iomem *base;
-	struct clk_init_data init = { };
 	int ret;
 
-	pll = devm_kzalloc(dev, sizeof(*pll), GFP_KERNEL);
-	if (!pll)
-		return -ENOMEM;
+	pll_data = of_device_get_match_data(dev);
+	if (!pll_data) {
+		dev_err(dev, "failed to get platform data\n");
+		return -ENODEV;
+	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	base = devm_ioremap_resource(dev, res);
@@ -57,30 +146,26 @@ static int qcom_a53pll_probe(struct platform_device *pdev)
 	if (IS_ERR(regmap))
 		return PTR_ERR(regmap);
 
-	pll->l_reg = 0x04;
-	pll->m_reg = 0x08;
-	pll->n_reg = 0x0c;
-	pll->config_reg = 0x14;
-	pll->mode_reg = 0x00;
-	pll->status_reg = 0x1c;
-	pll->status_bit = 16;
-	pll->freq_tbl = a53pll_freq;
-
-	init.name = "a53pll";
-	init.parent_names = (const char *[]){ "xo" };
-	init.num_parents = 1;
-	init.ops = &clk_pll_sr2_ops;
-	init.flags = CLK_IS_CRITICAL;
-	pll->clkr.hw.init = &init;
-
-	ret = devm_clk_register_regmap(dev, &pll->clkr);
+	if (pll_data->flags & PLL_IS_ALPHA) {
+		struct clk_alpha_pll *alpha_pll =
+			pll_data->a53pll.alpha_pll.pll;
+		struct alpha_pll_config *alpha_pll_config =
+			pll_data->a53pll.alpha_pll.pll_config;
+
+		clk_alpha_pll_configure(alpha_pll, regmap, alpha_pll_config);
+		clkr = &pll_data->a53pll.alpha_pll.pll->clkr;
+	} else {
+		clkr = &pll_data->a53pll.pll->clkr;
+	}
+
+	ret = devm_clk_register_regmap(dev, clkr);
 	if (ret) {
 		dev_err(dev, "failed to register regmap clock: %d\n", ret);
 		return ret;
 	}
 
 	ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get,
-					  &pll->clkr.hw);
+					  &clkr->hw);
 	if (ret) {
 		dev_err(dev, "failed to add clock provider: %d\n", ret);
 		return ret;
@@ -90,7 +175,8 @@ static int qcom_a53pll_probe(struct platform_device *pdev)
 }
 
 static const struct of_device_id qcom_a53pll_match_table[] = {
-	{ .compatible = "qcom,msm8916-a53pll" },
+	{ .compatible = "qcom,msm8916-a53pll", .data = &msm8996pll_data},
+	{ .compatible = "qcom,ipq6018-a53pll", .data = &ipq6018pll_data},
 	{ }
 };
 
Signature · 1 line
2.7.4
#5 lore raw

PATCH v2 4/8 clk: qcom: Add DT bindings for ipq6018 apss clock controller

In reply to Sivaprakash Murugesan

add dt-binding for ipq6018 apss clock controller

---
[V2]
* Addressed review comments from Rob and Sibi

 include/dt-bindings/clock/qcom,apss-ipq.h | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 include/dt-bindings/clock/qcom,apss-ipq.h
include/dt-bindings/clock/qcom,apss-ipq.h new file +12 -0
new file mode 100644
index 0000000..77b6e05
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_CLOCK_QCA_APSS_IPQ6018_H
+#define _DT_BINDINGS_CLOCK_QCA_APSS_IPQ6018_H
+
+#define APCS_ALIAS0_CLK_SRC			0
+#define APCS_ALIAS0_CORE_CLK			1
+
+#endif
Signature · 1 line
2.7.4
#6 lore raw

PATCH v2 5/8 clk: qcom: Add ipq apss clock controller

In reply to Sivaprakash Murugesan

The CPU on Qualcomm's IPQ platform devices are clocked primarily by a PLL and xo which are connected to a mux and enable block, This patch adds support for the mux and the enable.

---
[V2]
* Addressed review comments from Stephen.
* Moved the PLL to separate patch

 drivers/clk/qcom/Kconfig    |  10 +++++
 drivers/clk/qcom/Makefile   |   1 +
 drivers/clk/qcom/apss-ipq.c | 107 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 118 insertions(+)
 create mode 100644 drivers/clk/qcom/apss-ipq.c
drivers/clk/qcom/Kconfig +10 -0
index 15cdcdc..8573f2e 100644
@@ -89,6 +89,16 @@ config APQ_MMCC_8084
 	  Say Y if you want to support multimedia devices such as display,
 	  graphics, video encode/decode, camera, etc.
 
+config IPQ_APSS
+	tristate "IPQ APSS Clock Controller"
+	default N
+	help
+	  Support for APSS clock controller on ipq platform devices. The
+	  APSS clock controller manages the Mux and enable block that feeds the
+	  CPUs.
+	  Say Y if you want to support CPU frequency scaling on
+	  ipq based devices.
+
 config IPQ_GCC_4019
 	tristate "IPQ4019 Global Clock Controller"
 	help
drivers/clk/qcom/Makefile +1 -0
index 656a87e..1e4b296 100644
@@ -19,6 +19,7 @@ clk-qcom-$(CONFIG_QCOM_GDSC) += gdsc.o
 # Keep alphabetically sorted by config
 obj-$(CONFIG_APQ_GCC_8084) += gcc-apq8084.o
 obj-$(CONFIG_APQ_MMCC_8084) += mmcc-apq8084.o
+obj-$(CONFIG_IPQ_APSS) += apss-ipq.o
 obj-$(CONFIG_IPQ_GCC_4019) += gcc-ipq4019.o
 obj-$(CONFIG_IPQ_GCC_6018) += gcc-ipq6018.o
 obj-$(CONFIG_IPQ_GCC_806X) += gcc-ipq806x.o
drivers/clk/qcom/apss-ipq.c new file +107 -0

107 lines not on this page · raw message

Signature · 1 line
2.7.4
#7 lore raw

PATCH v2 6/8 dt-bindings: mailbox: Add dt-bindings for ipq6018 apcs global block

In reply to Sivaprakash Murugesan

Add dt-bindings for ipq6018 mailbox driver

---
 .../bindings/mailbox/qcom,apcs-kpss-global.yaml         | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.yaml +15 -2
index b46474b..07180c0 100644
@@ -16,6 +16,7 @@ maintainers:
 properties:
   compatible:
     enum:
+      - qcom,ipq6018-apcs-apps-global
       - qcom,ipq8074-apcs-apps-global
       - qcom,msm8916-apcs-kpss-global
       - qcom,msm8996-apcs-hmss-global
@@ -36,7 +37,7 @@ properties:
     const: 1
 
   '#clock-cells':
-    const: 0
+    enum: [ 0, 1 ]
 
   clock-names:
     description:
@@ -45,7 +46,7 @@ properties:
     maxItems: 2
     items:
       - const: pll
-      - const: aux
+      - enum: [ aux, xo ]
 
 required:
   - compatible
@@ -86,3 +87,15 @@ examples:
         clock-names = "pll", "aux";
         #clock-cells = <0>;
     };
+
+  # Example apcs with ipq6018
+  - |
+    #include "dt-bindings/clock/qcom,apss-ipq.h"
+    apcs_ipq: mailbox@b111000 {
+        compatible = "qcom,ipq6018-apcs-apps-global";
+        reg = <0x0b111000 0x1000>;
+        #clock-cells = <1>;
+        clocks = <&a53pll>, <&xo>;
+        clock-names = "pll", "xo";
+        #mbox-cells = <1>;
+    };
Signature · 1 line
2.7.4
#8 lore raw

PATCH v2 7/8 mailbox: qcom: Add ipq6018 apcs compatible

In reply to Sivaprakash Murugesan

The Qualcomm ipq6018 has apcs block, add compatible for the same. Also, the apcs provides a clock controller functionality similar to msm8916 but the clock driver is different.

Create a child platform device based on the apcs compatible for the clock controller functionality.

---
 drivers/mailbox/qcom-apcs-ipc-mailbox.c | 22 +++++++++++++++-------
 1 file changed, 15 insertions(+), 7 deletions(-)
drivers/mailbox/qcom-apcs-ipc-mailbox.c +15 -7
index eeebafd..19f6ba1 100644
@@ -45,6 +45,16 @@ static const struct mbox_chan_ops qcom_apcs_ipc_ops = {
 	.send_data = qcom_apcs_ipc_send_data,
 };
 
+static const struct of_device_id apcs_clk_match_table[] = {
+	{ .compatible = "qcom,msm8916-apcs-kpss-global",
+	  .data = "qcom-apcs-msm8916-clk", },
+	{ .compatible = "qcom,qcs404-apcs-apps-global",
+	  .data = "qcom-apcs-msm8916-clk", },
+	{ .compatible = "qcom,ipq6018-apcs-apps-global",
+	  .data = "qcom,apss-ipq-clk", },
+	{}
+};
+
 static int qcom_apcs_ipc_probe(struct platform_device *pdev)
 {
 	struct qcom_apcs_ipc *apcs;
@@ -54,11 +64,7 @@ static int qcom_apcs_ipc_probe(struct platform_device *pdev)
 	void __iomem *base;
 	unsigned long i;
 	int ret;
-	const struct of_device_id apcs_clk_match_table[] = {
-		{ .compatible = "qcom,msm8916-apcs-kpss-global", },
-		{ .compatible = "qcom,qcs404-apcs-apps-global", },
-		{}
-	};
+	const struct of_device_id *clk_device;
 
 	apcs = devm_kzalloc(&pdev->dev, sizeof(*apcs), GFP_KERNEL);
 	if (!apcs)
@@ -93,9 +99,10 @@ static int qcom_apcs_ipc_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	if (of_match_device(apcs_clk_match_table, &pdev->dev)) {
+	clk_device = of_match_device(apcs_clk_match_table, &pdev->dev);
+	if (clk_device) {
 		apcs->clk = platform_device_register_data(&pdev->dev,
-							  "qcom-apcs-msm8916-clk",
+							  (const char *)clk_device->data,
 							  PLATFORM_DEVID_NONE,
 							  NULL, 0);
 		if (IS_ERR(apcs->clk))
@@ -127,6 +134,7 @@ static const struct of_device_id qcom_apcs_ipc_of_match[] = {
 	{ .compatible = "qcom,sdm845-apss-shared", .data = (void *)12 },
 	{ .compatible = "qcom,sm8150-apss-shared", .data = (void *)12 },
 	{ .compatible = "qcom,ipq8074-apcs-apps-global", .data = (void *)8 },
+	{ .compatible = "qcom,ipq6018-apcs-apps-global", .data = (void *)8 },
 	{}
 };
 MODULE_DEVICE_TABLE(of, qcom_apcs_ipc_of_match);
Signature · 1 line
2.7.4
#9 lore raw

PATCH v2 8/8 arm64: dts: ipq6018: Add a53 pll and apcs clock

In reply to Sivaprakash Murugesan

add support for a53 pll and apcs clock.

---
 arch/arm64/boot/dts/qcom/ipq6018.dtsi | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)
arch/arm64/boot/dts/qcom/ipq6018.dtsi +13 -3
index 1aa8d85..3c2d91a 100644
@@ -294,12 +294,22 @@
 		};
 
 		apcs_glb: mailbox@b111000 {
-			compatible = "qcom,ipq8074-apcs-apps-global";
-			reg = <0x0b111000 0xc>;
-
+			compatible = "qcom,ipq6018-apcs-apps-global";
+			reg = <0x0b111000 0x1000>;
+			#clock-cells = <1>;
+			clocks = <&a53pll>, <&xo>;
+			clock-names = "pll", "xo";
 			#mbox-cells = <1>;
 		};
 
+		a53pll: clock@b116000 {
+			compatible = "qcom,ipq6018-a53pll";
+			reg = <0x0b116000 0x40>;
+			#clock-cells = <0>;
+			clocks = <&xo>;
+			clock-names = "xo";
+		};
+
 		timer {
 			compatible = "arm,armv8-timer";
 			interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
Signature · 1 line
2.7.4