Skip to contentSkip to conversation

MX31: NAND boot for PDK boards.

PATCH Superseded Magnus Lilja 4 participants 33 messages Jun 13, 2009 – Jul 7, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v4 cover MX31: NAND boot for PDK boards.

Hi all,

This is the latest set of patches that introduces NAND boot support for the i.MX31 CPU in general and the PDK board especially.

The patches apply on u-boot/next. For u-boot-arm/next I get an error from StGit when applying the CONFIG_PRELOADER patch but that's because the u-boot-arm/next is not update (as of this email). Don't know if git resolves the problem (it's the file onenand_ipl/board/apollon/Makefile that causes the problem), however after fixing that manually the u-boot-arm/next also builds fine with these patches.

This update takes of the comments received from Wolfgang Denk.

The code boots on i.MX31 PDK board using large page NAND, it should work for small page NAND as well but that has not been tested.

Regards, Magnus Lilja

Jean-Christophe PLAGNIOL-VILLARD (1):
ARM: Add macros.h to be used in assembler file.

Magnus Lilja (5):
ARM1136: Introduce CONFIG_PRELOADER macro.
MX31: Add NAND SPL for i.MX31.
i.MX31: Create a common device file.
MX31: Add basic support for Freescale i.MX31 PDK board.
MX31: Add NAND SPL boot support to i.MX31 PDK board.

 MAINTAINERS                                 |    4 +
 MAKEALL                                     |    2 +
 Makefile                                    |   13 ++-
 README                                      |    5 +
 board/freescale/mx31pdk/Makefile            |   52 ++++++
 board/freescale/mx31pdk/config.mk           |    5 +
 board/freescale/mx31pdk/lowlevel_init.S     |  114 ++++++++++++
 board/freescale/mx31pdk/mx31pdk.c           |   63 +++++++
 cpu/arm1136/mx31/Makefile                   |    1 +
 cpu/arm1136/mx31/devices.c                  |   56 ++++++
 cpu/arm1136/start.S                         |   33 ++--
 include/asm-arm/arch-mx31/mx31-regs.h       |   61 +++++++
 include/asm-arm/arch-mx31/mx31.h            |    3 +
 include/asm-arm/macro.h                     |   74 ++++++++
 include/configs/mx31pdk.h                   |  177 ++++++++++++++++++
 include/fsl_nfc.h                           |  109 +++++++++++
 nand_spl/board/freescale/mx31pdk/Makefile   |   54 ++++++
 nand_spl/board/freescale/mx31pdk/config.mk  |    5 +
 nand_spl/board/freescale/mx31pdk/u-boot.lds |   36 ++++
 nand_spl/nand_boot_fsl_nfc.c                |  259 +++++++++++++++++++++++++++
 onenand_ipl/board/apollon/Makefile          |    4 +-
 21 files changed, 1113 insertions(+), 17 deletions(-)
 create mode 100644 board/freescale/mx31pdk/Makefile
 create mode 100644 board/freescale/mx31pdk/config.mk
 create mode 100644 board/freescale/mx31pdk/lowlevel_init.S
 create mode 100644 board/freescale/mx31pdk/mx31pdk.c
 create mode 100644 cpu/arm1136/mx31/devices.c
 create mode 100644 include/asm-arm/macro.h
 create mode 100644 include/configs/mx31pdk.h
 create mode 100644 include/fsl_nfc.h
 create mode 100644 nand_spl/board/freescale/mx31pdk/Makefile
 create mode 100644 nand_spl/board/freescale/mx31pdk/config.mk
 create mode 100644 nand_spl/board/freescale/mx31pdk/u-boot.lds
 create mode 100644 nand_spl/nand_boot_fsl_nfc.c
#1 lore raw

PATCH v4 1/6 ARM1136: Introduce CONFIG_PRELOADER macro.

Currently CONFIG_ONENAND_IPL is used in a number of #ifdef's in start.S. In preparation for adding support for NAND SPL the macro CONFIG_PRELOADER is introducted and replaces the CONFIG_ONENAND_IPL in start.S.

---

NOTE: This patch applies to u-boot/next but not u-boot-arm/next since the OBJCFLAGS spelling error is corrected in u-boot/next. Atleast StGit had problems applying the patch to u-boot-arm/next, don't know what git thinks about.

 README                             |    5 +++++
 cpu/arm1136/start.S                |   24 ++++++++++++------------
 onenand_ipl/board/apollon/Makefile |    4 ++--
 3 files changed, 19 insertions(+), 14 deletions(-)
README +5 -0
index 561c100..0e84337 100644
@@ -2702,6 +2702,11 @@ Low Level (hardware related) configuration options:
 		some other boot loader or by a debugger which
 		performs these initializations itself.
 
+- CONFIG_PRELOADER
+
+		Modifies the behaviour of start.S when compiling a loader
+		that is executed before the actual U-Boot. E.g. when
+		compiling a NAND SPL.
 
 Building the Software:
 ======================
cpu/arm1136/start.S +12 -12
index 999b184..28cb5fd 100644
@@ -32,7 +32,7 @@
 #include <version.h>
 .globl _start
 _start: b	reset
-#ifdef CONFIG_ONENAND_IPL
+#ifdef CONFIG_PRELOADER
 	ldr	pc, _hang
 	ldr	pc, _hang
 	ldr	pc, _hang
@@ -67,7 +67,7 @@ _not_used:		.word not_used
 _irq:			.word irq
 _fiq:			.word fiq
 _pad:			.word 0x12345678 /* now 16*4=64 */
-#endif	/* CONFIG_ONENAND_IPL */
+#endif	/* CONFIG_PRELOADER */
 .global _end_vect
 _end_vect:
 
@@ -156,9 +156,9 @@ relocate:				/* relocate U-Boot to RAM	    */
 	adr	r0, _start		/* r0 <- current position of code   */
 	ldr	r1, _TEXT_BASE		/* test if we run from flash or RAM */
 	cmp	r0, r1			/* don't reloc during debug	    */
-#ifndef CONFIG_ONENAND_IPL
+#ifndef CONFIG_PRELOADER
 	beq	stack_setup
-#endif	/* CONFIG_ONENAND_IPL */
+#endif	/* CONFIG_PRELOADER */
 
 	ldr	r2, _armboot_start
 	ldr	r3, _bss_start
@@ -175,7 +175,7 @@ copy_loop:
 	/* Set up the stack						    */
 stack_setup:
 	ldr	r0, _TEXT_BASE		/* upper 128 KiB: relocated uboot   */
-#ifdef CONFIG_ONENAND_IPL
+#ifdef CONFIG_PRELOADER
 	sub	sp, r0, #128		/* leave 32 words for abort-stack   */
 #else
 	sub	r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area			    */
@@ -184,14 +184,14 @@ stack_setup:
 	sub	r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
 #endif
 	sub	sp, r0, #12		/* leave 3 words for abort-stack    */
-#endif	/* CONFIG_ONENAND_IPL */
+#endif	/* CONFIG_PRELOADER */
 
 clear_bss:
 	ldr	r0, _bss_start		/* find start of bss segment	    */
 	ldr	r1, _bss_end		/* stop here			    */
 	mov	r2, #0x00000000		/* clear			    */
 
-#ifndef CONFIG_ONENAND_IPL
+#ifndef CONFIG_PRELOADER
 clbss_l:str	r2, [r0]		/* clear loop...		    */
 	add	r0, r0, #4
 	cmp	r0, r1
@@ -244,7 +244,7 @@ cpu_init_crit:
 	mov	lr, ip		/* restore link */
 	mov	pc, lr		/* back to my caller */
 
-#ifndef CONFIG_ONENAND_IPL
+#ifndef CONFIG_PRELOADER
 /*
  *************************************************************************
  *
@@ -357,17 +357,17 @@ cpu_init_crit:
 	.macro get_fiq_stack			@ setup FIQ stack
 	ldr	sp, FIQ_STACK_START
 	.endm
-#endif	/* CONFIG_ONENAND_IPL */
+#endif	/* CONFIG_PRELOADER */
 
 /*
  * exception handlers
  */
-#ifdef CONFIG_ONENAND_IPL
+#ifdef CONFIG_PRELOADER
 	.align	5
 do_hang:
 	ldr	sp, _TEXT_BASE			/* use 32 words about stack */
 	bl	hang				/* hang and never return */
-#else	/* !CONFIG_ONENAND IPL */
+#else	/* !CONFIG_PRELOADER */
 	.align	5
 undefined_instruction:
 	get_bad_stack
@@ -435,4 +435,4 @@ fiq:
 arm1136_cache_flush:
 		mcr	p15, 0, r1, c7, c5, 0	@ invalidate I cache
 		mov	pc, lr			@ back to caller
-#endif	/* CONFIG_ONENAND_IPL */
+#endif	/* CONFIG_PRELOADER */
onenand_ipl/board/apollon/Makefile +2 -2
index f6c36ec..49a8e90 100644
@@ -4,8 +4,8 @@ include $(TOPDIR)/onenand_ipl/board/$(BOARDDIR)/config.mk
 
 LDSCRIPT= $(TOPDIR)/onenand_ipl/board/$(BOARDDIR)/u-boot.onenand.lds
 LDFLAGS	= -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS)
-AFLAGS	+= -DCONFIG_ONENAND_IPL
-CFLAGS	+= -DCONFIG_ONENAND_IPL
+AFLAGS	+= -DCONFIG_PRELOADER -DCONFIG_ONENAND_IPL
+CFLAGS	+= -DCONFIG_PRELOADER -DCONFIG_ONENAND_IPL
 OBJCFLAGS += --gap-fill=0x00
 
 SOBJS	:= low_levelinit.o
Signature · 1 line
1.5.6
#2 lore raw

PATCH v4 2/6 MX31: Add NAND SPL for i.MX31.

This patch adds the NAND SPL framework needed to boot i.MX31 boards from NAND.

It has been tested on a i.MX31 PDK board with large page NAND. Small page NANDs should work as well, but this has not been tested.

Note: The i.MX31 NFC uses a non-standard layout for large page NANDs, whether this is compatible with a particular setup depends on how the NAND device is programmed by the flash programmer (e.g. JTAG debugger).

The patch is based on the work by Maxim Artamonov.

---

Changes from last version: Fixed comments received from Wolfang Denk.

 cpu/arm1136/start.S                   |    9 +-
 include/asm-arm/arch-mx31/mx31-regs.h |    5 +
 include/fsl_nfc.h                     |  109 ++++++++++++++
 nand_spl/nand_boot_fsl_nfc.c          |  259 +++++++++++++++++++++++++++++++++
 4 files changed, 380 insertions(+), 2 deletions(-)
 create mode 100644 include/fsl_nfc.h
 create mode 100644 nand_spl/nand_boot_fsl_nfc.c
cpu/arm1136/start.S +7 -2
index 28cb5fd..957f438 100644
@@ -200,12 +200,15 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
 
 	ldr	pc, _start_armboot
 
+#ifdef CONFIG_NAND_SPL
+_start_armboot: .word nand_boot
+#else
 #ifdef CONFIG_ONENAND_IPL
 _start_armboot: .word start_oneboot
 #else
 _start_armboot: .word start_armboot
-#endif
-
+#endif /* CONFIG_ONENAND_IPL */
+#endif /* CONFIG_NAND_SPL */
 
 /*
  *************************************************************************
@@ -217,6 +220,7 @@ _start_armboot: .word start_armboot
  *
  *************************************************************************
  */
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
 cpu_init_crit:
 	/*
 	 * flush v4 I/D caches
@@ -243,6 +247,7 @@ cpu_init_crit:
 	bl	lowlevel_init	/* go setup pll,mux,memory */
 	mov	lr, ip		/* restore link */
 	mov	pc, lr		/* back to my caller */
+#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
 
 #ifndef CONFIG_PRELOADER
 /*
include/asm-arm/arch-mx31/mx31-regs.h +5 -0
index a8a05c8..c2e7dcf 100644
@@ -194,4 +194,9 @@
 #define CS5_BASE	0xB6000000
 #define PCMCIA_MEM_BASE	0xC0000000
 
+/*
+ * NAND controller
+ */
+#define NFC_BASE_ADDR	0xB8000000
+
 #endif /* __ASM_ARCH_MX31_REGS_H */
include/fsl_nfc.h new file +109 -0

109 lines not on this page · raw message

nand_spl/nand_boot_fsl_nfc.c new file +259 -0

259 lines not on this page · raw message

Signature · 1 line
1.5.6
#3 lore raw

PATCH v4 3/6 ARM: Add macros.h to be used in assembler file.

From: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>

---

Changes from last version: Added documentation for the macros.

 include/asm-arm/macro.h |   74 +++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 74 insertions(+), 0 deletions(-)
 create mode 100644 include/asm-arm/macro.h
include/asm-arm/macro.h new file +74 -0
new file mode 100644
index 0000000..57b5260
@@ -0,0 +1,74 @@
+/*
+ * include/asm-arm/macro.h
+ *
+ * Copyright (C) 2009 Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __ASM_ARM_MACRO_H__
+#define __ASM_ARM_MACRO_H__
+#ifdef __ASSEMBLY__
+
+/*
+ * These macros provide a convenient way to write 8, 16 and 32 bit data
+ * to any address.
+ * Registers r4 and r5 are used, any data in these registers are
+ * overwritten by the macros.
+ * The macros are valid for any ARM architecture, they do not implement
+ * any memory barriers so caution is recommended when using these when the
+ * caches are enabled or on a multi-core system.
+ */
+
+.macro	write32, addr, data
+	ldr	r4, =\addr
+	ldr	r5, =\data
+	str	r5, [r4]
+.endm
+
+.macro	write16, addr, data
+	ldr	r4, =\addr
+	ldrh	r5, =\data
+	strh	r5, [r4]
+.endm
+
+.macro	write8, addr, data
+	ldr	r4, =\addr
+	ldrb	r5, =\data
+	strb	r5, [r4]
+.endm
+
+/*
+ * This macro generates a loop that can be used for delays in the code.
+ * Register r4 is used, any data in this register is overwritten by the
+ * macro.
+ * The macro is valid for any ARM architeture. The actual time spent in the
+ * loop will vary from CPU to CPU though.
+ */
+
+.macro	wait_timer, time
+	ldr	r4, =\time
+1:
+	nop
+	subs	r4, r4, #1
+	bcs	1b
+.endm
+
+#endif /* __ASSEMBLY__ */
+#endif /* __ASM_ARM_MACRO_H__ */
Signature · 1 line
1.5.6
#4 lore raw

PATCH v4 4/6 i.MX31: Create a common device file.

---
 cpu/arm1136/mx31/Makefile        |    1 +
 cpu/arm1136/mx31/devices.c       |   56 ++++++++++++++++++++++++++++++++++++++
 include/asm-arm/arch-mx31/mx31.h |    3 ++
 3 files changed, 60 insertions(+), 0 deletions(-)
 create mode 100644 cpu/arm1136/mx31/devices.c
cpu/arm1136/mx31/Makefile +1 -0
index 1e49e8d..c8e18f7 100644
@@ -27,6 +27,7 @@ LIB	= $(obj)lib$(SOC).a
 
 COBJS	+= generic.o
 COBJS	+= timer.o
+COBJS	+= devices.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
cpu/arm1136/mx31/devices.c new file +56 -0

56 lines not on this page · raw message

include/asm-arm/arch-mx31/mx31.h +3 -0
index 1d475dd..53b9f27 100644
@@ -47,4 +47,7 @@ static inline void mx31_gpio_set(unsigned int gpio, unsigned int value)
 }
 #endif
 
+void mx31_uart1_hw_init(void);
+void mx31_spi2_hw_init(void);
+
 #endif /* __ASM_ARCH_MX31_H */
Signature · 1 line
1.5.6
#5 lore raw

PATCH v4 5/6 MX31: Add basic support for Freescale i.MX31 PDK board.

Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).

This patch assumes that some other program performs the actual NAND boot.

---
 MAINTAINERS                           |    4 +
 MAKEALL                               |    1 +
 Makefile                              |    3 +
 board/freescale/mx31pdk/Makefile      |   52 +++++++++++
 board/freescale/mx31pdk/config.mk     |    1 +
 board/freescale/mx31pdk/mx31pdk.c     |   63 +++++++++++++
 include/asm-arm/arch-mx31/mx31-regs.h |    2 +
 include/configs/mx31pdk.h             |  162 +++++++++++++++++++++++++++++++++
 8 files changed, 288 insertions(+), 0 deletions(-)
 create mode 100644 board/freescale/mx31pdk/Makefile
 create mode 100644 board/freescale/mx31pdk/config.mk
 create mode 100644 board/freescale/mx31pdk/mx31pdk.c
 create mode 100644 include/configs/mx31pdk.h
MAINTAINERS +4 -0
index 1f6008f..8eb54e1 100644
@@ -528,6 +528,10 @@ Thomas Elste <[email protected]>
 
 	modnet50	ARM720T (NET+50)
 
+Fabio Estevam <[email protected]>
+
+	mx31pdk		i.MX31
+
 Peter Figuli <[email protected]>
 
 	wepep250	xscale
MAKEALL +1 -0
index f48a08e..0757064 100755
@@ -552,6 +552,7 @@ LIST_ARM11="			\
 	imx31_phycore		\
 	imx31_phycore_eet	\
 	mx31ads			\
+	mx31pdk			\
 	qong			\
 	smdk6400		\
 "
Makefile +3 -0
index aa4646f..e445e51 100644
@@ -3115,6 +3115,9 @@ imx31_phycore_config	: unconfig
 mx31ads_config		: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm1136 mx31ads freescale mx31
 
+mx31pdk_config		: unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm1136 mx31pdk freescale mx31
+
 omap2420h4_config	: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm1136 omap2420h4 NULL omap24xx
 
board/freescale/mx31pdk/Makefile new file +52 -0

52 lines not on this page · raw message

board/freescale/mx31pdk/config.mk new file +1 -0
new file mode 100644
index 0000000..d34dc02
@@ -0,0 +1 @@
+TEXT_BASE = 0x87f00000
board/freescale/mx31pdk/mx31pdk.c new file +63 -0

63 lines not on this page · raw message

include/asm-arm/arch-mx31/mx31-regs.h +2 -0
index c2e7dcf..76f4d53 100644
@@ -84,6 +84,8 @@
 #define IPU_CONF_IC_EN		(1<<1)
 #define IPU_CONF_SCI_EN		(1<<0)
 
+#define ARM_PPMRR		0x40000015
+
 #define WDOG_BASE		0x53FDC000
 
 /*
include/configs/mx31pdk.h new file +162 -0

162 lines not on this page · raw message

Signature · 1 line
1.5.6
#6 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

---
 MAKEALL                                     |    1 +
 Makefile                                    |   14 +++-
 board/freescale/mx31pdk/config.mk           |    4 +
 board/freescale/mx31pdk/lowlevel_init.S     |  114 +++++++++++++++++++++++++++
 include/asm-arm/arch-mx31/mx31-regs.h       |   54 +++++++++++++
 include/configs/mx31pdk.h                   |   21 ++++-
 nand_spl/board/freescale/mx31pdk/Makefile   |   54 +++++++++++++
 nand_spl/board/freescale/mx31pdk/config.mk  |    5 +
 nand_spl/board/freescale/mx31pdk/u-boot.lds |   36 +++++++++
 9 files changed, 297 insertions(+), 6 deletions(-)
 create mode 100644 board/freescale/mx31pdk/lowlevel_init.S
 create mode 100644 nand_spl/board/freescale/mx31pdk/Makefile
 create mode 100644 nand_spl/board/freescale/mx31pdk/config.mk
 create mode 100644 nand_spl/board/freescale/mx31pdk/u-boot.lds
MAKEALL +1 -0
index 0757064..1f7cab4 100755
@@ -553,6 +553,7 @@ LIST_ARM11="			\
 	imx31_phycore_eet	\
 	mx31ads			\
 	mx31pdk			\
+	mx31pdk_nand		\
 	qong			\
 	smdk6400		\
 "
Makefile +11 -3
index e445e51..29d1f22 100644
@@ -376,7 +376,7 @@ $(LDSCRIPT):	depend
 $(NAND_SPL):	$(TIMESTAMP_FILE) $(VERSION_FILE) $(obj)include/autoconf.mk
 		$(MAKE) -C nand_spl/board/$(BOARDDIR) all
 
-$(U_BOOT_NAND):	$(NAND_SPL) $(obj)u-boot.bin
+$(U_BOOT_NAND):	$(NAND_SPL) $(obj)u-boot.bin $(obj)include/autoconf.mk
 		cat $(obj)nand_spl/u-boot-spl-16k.bin $(obj)u-boot.bin > $(obj)u-boot-nand.bin
 
 $(ONENAND_IPL):	$(TIMESTAMP_FILE) $(VERSION_FILE) $(obj)include/autoconf.mk
@@ -3115,8 +3115,16 @@ imx31_phycore_config	: unconfig
 mx31ads_config		: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm1136 mx31ads freescale mx31
 
-mx31pdk_config		: unconfig
-	@$(MKCONFIG) $(@:_config=) arm arm1136 mx31pdk freescale mx31
+mx31pdk_config \
+mx31pdk_nand_config	: unconfig
+	@mkdir -p $(obj)include
+	@if [ -n "$(findstring _nand_,$@)" ]; then					\
+		echo "#define CONFIG_NAND_U_BOOT" >> $(obj)include/config.h;		\
+	else										\
+		echo "#define CONFIG_SKIP_LOWLEVEL_INIT" >> $(obj)include/config.h;	\
+		echo "#define CONFIG_SKIP_RELOCATE_UBOOT" >> $(obj)include/config.h;	\
+	fi
+	@$(MKCONFIG) -a mx31pdk arm arm1136 mx31pdk freescale mx31
 
 omap2420h4_config	: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm1136 omap2420h4 NULL omap24xx
board/freescale/mx31pdk/config.mk +4 -0
index d34dc02..dcaa09f 100644
@@ -1 +1,5 @@
+ifdef CONFIG_NAND_SPL
+TEXT_BASE = 0x87ec0000
+else
 TEXT_BASE = 0x87f00000
+endif
board/freescale/mx31pdk/lowlevel_init.S new file +114 -0

114 lines not on this page · raw message

include/asm-arm/arch-mx31/mx31-regs.h +54 -0

66 lines not on this page · raw message

include/configs/mx31pdk.h +18 -3
index ca7b960..1795a7e 100644
@@ -43,10 +43,10 @@
 #define CONFIG_SETUP_MEMORY_TAGS	1
 #define CONFIG_INITRD_TAG		1
 
-/* No support for NAND boot for i.MX31 PDK yet, so we rely on some other
- * program to initialize the SDRAM.
- */
+#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_SKIP_RELOCATE_UBOOT
+#endif
 
 /*
  * Size of malloc() pool
@@ -159,4 +159,19 @@
 
 #define CONFIG_ENV_SIZE		(128 * 1024)
 
+/* NAND configuration for the NAND_SPL */
+
+/* Start copying real U-boot from the second page */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x800
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	0x30000
+/* Load U-Boot to this address */
+#define CONFIG_SYS_NAND_U_BOOT_DST	0x87f00000
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
+
+#define CONFIG_SYS_NAND_PAGE_SIZE	0x800
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+#define CONFIG_SYS_NAND_PAGE_COUNT	64
+#define CONFIG_SYS_NAND_SIZE		(256 * 1024 * 1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	0
+
 #endif /* __CONFIG_H */
nand_spl/board/freescale/mx31pdk/Makefile new file +54 -0

54 lines not on this page · raw message

nand_spl/board/freescale/mx31pdk/config.mk new file +5 -0
new file mode 100644
index 0000000..198cafc
@@ -0,0 +1,5 @@
+PAD_TO	:= 2048
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
nand_spl/board/freescale/mx31pdk/u-boot.lds new file +36 -0
new file mode 100644
index 0000000..edd8430
@@ -0,0 +1,36 @@
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text :
+	{
+		start.o			(.text)
+		lowlevel_init.o		(.text)
+		nand_boot_fsl_nfc.o	(.text)
+		*(.text)
+		. = 2K;
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	. = .;
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}
Signature · 1 line
1.5.6
#7 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

Jean-Christpohe,

Seems like you missed the last part in my series, could you apply this one as well?

Regards, Magnus

2009/6/13 Magnus Lilja <[email protected]>:

Quoted 422 lines

---

?MAKEALL ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? | ? ?1 +
?Makefile ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| ? 14 +++-
?board/freescale/mx31pdk/config.mk ? ? ? ? ? | ? ?4 +
?board/freescale/mx31pdk/lowlevel_init.S ? ? | ?114 +++++++++++++++++++++++++++
?include/asm-arm/arch-mx31/mx31-regs.h ? ? ? | ? 54 +++++++++++++
?include/configs/mx31pdk.h ? ? ? ? ? ? ? ? ? | ? 21 ++++-
?nand_spl/board/freescale/mx31pdk/Makefile ? | ? 54 +++++++++++++
?nand_spl/board/freescale/mx31pdk/config.mk ?| ? ?5 +
?nand_spl/board/freescale/mx31pdk/u-boot.lds | ? 36 +++++++++

?9 files changed, 297 insertions(+), 6 deletions(-) ?create mode 100644 board/freescale/mx31pdk/lowlevel_init.S ?create mode 100644 nand_spl/board/freescale/mx31pdk/Makefile ?create mode 100644 nand_spl/board/freescale/mx31pdk/config.mk ?create mode 100644 nand_spl/board/freescale/mx31pdk/u-boot.lds

MAKEALL +1 -0
index 0757064..1f7cab4 100755
@@ -553,6 +553,7 @@ LIST_ARM11=" ? ? ? ? ? ? ? ? ? ? ? ?\
 ? ? ? ?imx31_phycore_eet ? ? ? \
 ? ? ? ?mx31ads ? ? ? ? ? ? ? ? \
 ? ? ? ?mx31pdk ? ? ? ? ? ? ? ? \
+ ? ? ? mx31pdk_nand ? ? ? ? ? ?\
 ? ? ? ?qong ? ? ? ? ? ? ? ? ? ?\
 ? ? ? ?smdk6400 ? ? ? ? ? ? ? ?\

?"

Makefile +0 -0
index e445e51..29d1f22 100644
@@ -376,7 +376,7 @@ $(LDSCRIPT): ? ? ? ?depend

?$(NAND_SPL): ? $(TIMESTAMP_FILE) $(VERSION_FILE) $(obj)include/autoconf.mk ? ? ? ? ? ? ? ?$(MAKE) -C nand_spl/board/$(BOARDDIR) all

-$(U_BOOT_NAND): ? ? ? ?$(NAND_SPL) $(obj)u-boot.bin
+$(U_BOOT_NAND): ? ? ? ?$(NAND_SPL) $(obj)u-boot.bin $(obj)include/autoconf.mk ? ? ? ? ? ? ? ?cat $(obj)nand_spl/u-boot-spl-16k.bin $(obj)u-boot.bin > $(obj)u-boot-nand.bin

?$(ONENAND_IPL): ? ? ? ?$(TIMESTAMP_FILE) $(VERSION_FILE) $(obj)include/autoconf.mk

Makefile +0 -0
@@ -3115,8 +3115,16 @@ imx31_phycore_config ? ? : unconfig

?mx31ads_config ? ? ? ? : unconfig
? ? ? ?@$(MKCONFIG) $(@:_config=) arm arm1136 mx31ads freescale mx31

Makefile +10 -2
-mx31pdk_config ? ? ? ? : unconfig
- ? ? ? @$(MKCONFIG) $(@:_config=) arm arm1136 mx31pdk freescale mx31
+mx31pdk_config \
+mx31pdk_nand_config ? ?: unconfig
+ ? ? ? @mkdir -p $(obj)include
+ ? ? ? @if [ -n "$(findstring _nand_,$@)" ]; then ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\
+ ? ? ? ? ? ? ? echo "#define CONFIG_NAND_U_BOOT" >> $(obj)include/config.h; ? ? ? ? ? ?\
+ ? ? ? else ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\
+ ? ? ? ? ? ? ? echo "#define CONFIG_SKIP_LOWLEVEL_INIT" >> $(obj)include/config.h; ? ? \
+ ? ? ? ? ? ? ? echo "#define CONFIG_SKIP_RELOCATE_UBOOT" >> $(obj)include/config.h; ? ?\
+ ? ? ? fi
+ ? ? ? @$(MKCONFIG) -a mx31pdk arm arm1136 mx31pdk freescale mx31

?omap2420h4_config ? ? ?: unconfig
? ? ? ?@$(MKCONFIG) $(@:_config=) arm arm1136 omap2420h4 NULL omap24xx

board/freescale/mx31pdk/config.mk +3 -0
index d34dc02..dcaa09f 100644
@@ -1 +1,5 @@
+ifdef CONFIG_NAND_SPL
+TEXT_BASE = 0x87ec0000
+else

?TEXT_BASE = 0x87f00000

board/freescale/mx31pdk/config.mk +1 -0
+endif
board/freescale/mx31pdk/lowlevel_init.S new file +114 -0
new file mode 100644
index 0000000..f913f90
@@ -0,0 +1,114 @@
+/*
+ * (C) Copyright 2009 Magnus Lilja <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+.globl lowlevel_init
+
+#include <asm/arch/mx31-regs.h>
+#include <asm/macro.h>
+
+#define CCM_CCMR_SETUP ? ? ? ? 0x074B0BF5
+#define CCM_PDR0_SETUP_532MHZ ?(PDR0_CSI_PODF(0x1ff) | PDR0_PER_PODF(7) | \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_HSP_PODF(3) | PDR0_NFC_PODF(5) | ? ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_IPG_PODF(1) | PDR0_MAX_PODF(3) | ? ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_MCU_PODF(0))
+#define CCM_MPCTL_SETUP_532MHZ (PLL_PD(0) | PLL_MFD(51) | PLL_MFI(10) | ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PLL_MFN(12))
+
+#define ESDMISC_MDDR_SETUP ? ? 0x00000004
+#define ESDMISC_MDDR_RESET_DL ?0x0000000c
+#define ESDCFG0_MDDR_SETUP ? ? 0x006ac73a
+
+#define ESDCTL_ROW_COL ? ? ? ? (ESDCTL_SDE | ESDCTL_ROW(2) | ESDCTL_COL(2))
+#define ESDCTL_SETTINGS ? ? ? ? ? ? ? ?(ESDCTL_ROW_COL | ESDCTL_SREFR(3) | \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?ESDCTL_DSIZ(2) | ESDCTL_BL(1))
+#define ESDCTL_PRECHARGE ? ? ? (ESDCTL_ROW_COL | ESDCTL_CMD_PRECHARGE)
+#define ESDCTL_AUTOREFRESH ? ? (ESDCTL_ROW_COL | ESDCTL_CMD_AUTOREFRESH)
+#define ESDCTL_LOADMODEREG ? ? (ESDCTL_ROW_COL | ESDCTL_CMD_LOADMODEREG)
+#define ESDCTL_RW ? ? ? ? ? ? ?ESDCTL_SETTINGS
+
+.globl lowlevel_init
+lowlevel_init:
+ ? ? ? /* Also setup the Peripheral Port Remap register inside the core */
+ ? ? ? ldr ? ? r0, =ARM_PPMRR ? ? ?/* start from AIPS 2GB region */
+ ? ? ? mcr ? ? p15, 0, r0, c15, c2, 4
+
+ ? ? ? write32 IPU_CONF, IPU_CONF_DI_EN
+ ? ? ? write32 CCM_CCMR, CCM_CCMR_SETUP
+
+ ? ? ? wait_timer ? ? ?0x40000
+
+ ? ? ? write32 CCM_CCMR, CCM_CCMR_SETUP | CCMR_MPE
+ ? ? ? write32 CCM_CCMR, (CCM_CCMR_SETUP | CCMR_MPE) & ~CCMR_MDS
+
+ ? ? ? /* Set up clock to 532MHz */
+ ? ? ? write32 CCM_PDR0, CCM_PDR0_SETUP_532MHZ
+ ? ? ? write32 CCM_MPCTL, CCM_MPCTL_SETUP_532MHZ
+
+ ? ? ? write32 CCM_SPCTL, PLL_PD(1) | PLL_MFD(4) | PLL_MFI(12) | PLL_MFN(1)
+
+ ? ? ? /* Set up MX31 DDR pins */
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SDCKE1_SDCLK_SDCLK_B, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_CAS_SDWE_SDCKE0, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_BCLK_RW_RAS, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_CS2_CS3_CS4, 0x1000
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_DQM3_EB0_EB1, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_DQM0_DQM1_DQM2, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SD29_SD30_SD31, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SD26_SD27_SD28, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SD23_SD24_SD25, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SD20_SD21_SD22, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SD17_SD18_SD19, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SD14_SD15_SD16, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SD11_SD12_SD13, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SD8_SD9_SD10, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SD5_SD6_SD7, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SD2_SD3_SD4, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_SDBA0_SD0_SD1, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_A24_A25_SDBA1, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_A21_A22_A23, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_A18_A19_A20, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_A15_A16_A17, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_A12_A13_A14, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_A10_MA10_A11, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_A7_A8_A9, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_A4_A5_A6, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_A1_A2_A3, 0
+ ? ? ? write32 IOMUXC_SW_PAD_CTL_VPG0_VPG1_A0, 0
+
+ ? ? ? /* Set up MX31 DDR Memory Controller */
+ ? ? ? write32 WEIM_ESDMISC, ESDMISC_MDDR_SETUP
+ ? ? ? write32 WEIM_ESDCFG0, ESDCFG0_MDDR_SETUP
+
+ ? ? ? /* Perform DDR init sequence */
+ ? ? ? write32 WEIM_ESDCTL0, ESDCTL_PRECHARGE
+ ? ? ? write32 CSD0_BASE | 0x0f00, 0x12344321
+ ? ? ? write32 WEIM_ESDCTL0, ESDCTL_AUTOREFRESH
+ ? ? ? write32 CSD0_BASE, 0x12344321
+ ? ? ? write32 CSD0_BASE, 0x12344321
+ ? ? ? write32 WEIM_ESDCTL0, ESDCTL_LOADMODEREG
+ ? ? ? write8 ?CSD0_BASE | 0x00000033, 0xda
+ ? ? ? write8 ?CSD0_BASE | 0x01000000, 0xff
+ ? ? ? write32 WEIM_ESDCTL0, ESDCTL_RW
+ ? ? ? write32 CSD0_BASE, 0xDEADBEEF
+ ? ? ? write32 WEIM_ESDMISC, ESDMISC_MDDR_RESET_DL
+
+ ? ? ? mov ? ? pc, lr
include/asm-arm/arch-mx31/mx31-regs.h +23 -0
index 76f4d53..51b02a2 100644
@@ -61,6 +61,29 @@
 ?#define PLL_MFI(x) ? ? ? ? ? ? (((x) & 0xf) << 10)
 ?#define PLL_MFN(x) ? ? ? ? ? ? (((x) & 0x3ff) << 0)
 
+#define WEIM_ESDCTL0 ? 0xB8001000
+#define WEIM_ESDCFG0 ? 0xB8001004
+#define WEIM_ESDCTL1 ? 0xB8001008
+#define WEIM_ESDCFG1 ? 0xB800100C
+#define WEIM_ESDMISC ? 0xB8001010
+
+#define ESDCTL_SDE ? ? ? ? ? ? ? ? ? ? (1 << 31)
+#define ESDCTL_CMD_RW ? ? ? ? ? ? ? ? ?(0 << 28)
+#define ESDCTL_CMD_PRECHARGE ? ? ? ? ? (1 << 28)
+#define ESDCTL_CMD_AUTOREFRESH ? ? ? ? (2 << 28)
+#define ESDCTL_CMD_LOADMODEREG ? ? ? ? (3 << 28)
+#define ESDCTL_CMD_MANUALREFRESH ? ? ? (4 << 28)
+#define ESDCTL_ROW_13 ? ? ? ? ? ? ? ? ?(2 << 24)
+#define ESDCTL_ROW(x) ? ? ? ? ? ? ? ? ?((x) << 24)
+#define ESDCTL_COL_9 ? ? ? ? ? ? ? ? ? (1 << 20)
+#define ESDCTL_COL(x) ? ? ? ? ? ? ? ? ?((x) << 20)
+#define ESDCTL_DSIZ(x) ? ? ? ? ? ? ? ? ((x) << 16)
+#define ESDCTL_SREFR(x) ? ? ? ? ? ? ? ? ? ? ? ?((x) << 13)
+#define ESDCTL_PWDT(x) ? ? ? ? ? ? ? ? ((x) << 10)
+#define ESDCTL_FP(x) ? ? ? ? ? ? ? ? ? ((x) << 8)
+#define ESDCTL_BL(x) ? ? ? ? ? ? ? ? ? ((x) << 7)
+#define ESDCTL_PRCT(x) ? ? ? ? ? ? ? ? ((x) << 0)
+

?#define WEIM_BASE ? ? ?0xb8002000
?#define CSCR_U(x) ? ? ?(WEIM_BASE + (x) * 0x10) ?#define CSCR_L(x) ? ? ?(WEIM_BASE + 4 + (x) * 0x10)

include/asm-arm/arch-mx31/mx31-regs.h +31 -0
@@ -181,6 +204,37 @@
 ?#define MUX_CSPI2_MOSI__I2C2_SCL IOMUX_MODE(MUX_CTL_CSPI2_MOSI, MUX_CTL_ALT1)
 ?#define MUX_CSPI2_MISO__I2C2_SDA IOMUX_MODE(MUX_CTL_CSPI2_MISO, MUX_CTL_ALT1)
 
+/* PAD control registers for SDR/DDR */
+#define IOMUXC_SW_PAD_CTL_SDCKE1_SDCLK_SDCLK_B (IOMUXC_BASE + 0x26C)
+#define IOMUXC_SW_PAD_CTL_CAS_SDWE_SDCKE0 ? ? ?(IOMUXC_BASE + 0x270)
+#define IOMUXC_SW_PAD_CTL_BCLK_RW_RAS ? ? ? ? ?(IOMUXC_BASE + 0x274)
+#define IOMUXC_SW_PAD_CTL_CS5_ECB_LBA ? ? ? ? ?(IOMUXC_BASE + 0x278)
+#define IOMUXC_SW_PAD_CTL_CS2_CS3_CS4 ? ? ? ? ?(IOMUXC_BASE + 0x27C)
+#define IOMUXC_SW_PAD_CTL_OE_CS0_CS1 ? ? ? ? ? (IOMUXC_BASE + 0x280)
+#define IOMUXC_SW_PAD_CTL_DQM3_EB0_EB1 ? ? ? ? (IOMUXC_BASE + 0x284)
+#define IOMUXC_SW_PAD_CTL_DQM0_DQM1_DQM2 ? ? ? (IOMUXC_BASE + 0x288)
+#define IOMUXC_SW_PAD_CTL_SD29_SD30_SD31 ? ? ? (IOMUXC_BASE + 0x28C)
+#define IOMUXC_SW_PAD_CTL_SD26_SD27_SD28 ? ? ? (IOMUXC_BASE + 0x290)
+#define IOMUXC_SW_PAD_CTL_SD23_SD24_SD25 ? ? ? (IOMUXC_BASE + 0x294)
+#define IOMUXC_SW_PAD_CTL_SD20_SD21_SD22 ? ? ? (IOMUXC_BASE + 0x298)
+#define IOMUXC_SW_PAD_CTL_SD17_SD18_SD19 ? ? ? (IOMUXC_BASE + 0x29C)
+#define IOMUXC_SW_PAD_CTL_SD14_SD15_SD16 ? ? ? (IOMUXC_BASE + 0x2A0)
+#define IOMUXC_SW_PAD_CTL_SD11_SD12_SD13 ? ? ? (IOMUXC_BASE + 0x2A4)
+#define IOMUXC_SW_PAD_CTL_SD8_SD9_SD10 ? ? ? ? (IOMUXC_BASE + 0x2A8)
+#define IOMUXC_SW_PAD_CTL_SD5_SD6_SD7 ? ? ? ? ?(IOMUXC_BASE + 0x2AC)
+#define IOMUXC_SW_PAD_CTL_SD2_SD3_SD4 ? ? ? ? ?(IOMUXC_BASE + 0x2B0)
+#define IOMUXC_SW_PAD_CTL_SDBA0_SD0_SD1 ? ? ? ? ? ? ? ?(IOMUXC_BASE + 0x2B4)
+#define IOMUXC_SW_PAD_CTL_A24_A25_SDBA1 ? ? ? ? ? ? ? ?(IOMUXC_BASE + 0x2B8)
+#define IOMUXC_SW_PAD_CTL_A21_A22_A23 ? ? ? ? ?(IOMUXC_BASE + 0x2BC)
+#define IOMUXC_SW_PAD_CTL_A18_A19_A20 ? ? ? ? ?(IOMUXC_BASE + 0x2C0)
+#define IOMUXC_SW_PAD_CTL_A15_A16_A17 ? ? ? ? ?(IOMUXC_BASE + 0x2C4)
+#define IOMUXC_SW_PAD_CTL_A12_A13_A14 ? ? ? ? ?(IOMUXC_BASE + 0x2C8)
+#define IOMUXC_SW_PAD_CTL_A10_MA10_A11 ? ? ? ? (IOMUXC_BASE + 0x2CC)
+#define IOMUXC_SW_PAD_CTL_A7_A8_A9 ? ? ? ? ? ? (IOMUXC_BASE + 0x2D0)
+#define IOMUXC_SW_PAD_CTL_A4_A5_A6 ? ? ? ? ? ? (IOMUXC_BASE + 0x2D4)
+#define IOMUXC_SW_PAD_CTL_A1_A2_A3 ? ? ? ? ? ? (IOMUXC_BASE + 0x2D8)
+#define IOMUXC_SW_PAD_CTL_VPG0_VPG1_A0 ? ? ? ? (IOMUXC_BASE + 0x2DC)
+

?/*
?* Memory regions and CS
?*/

include/configs/mx31pdk.h +0 -0
index ca7b960..1795a7e 100644
@@ -43,10 +43,10 @@

?#define CONFIG_SETUP_MEMORY_TAGS ? ? ? 1
?#define CONFIG_INITRD_TAG ? ? ? ? ? ? ?1

include/configs/mx31pdk.h +1 -3
-/* No support for NAND boot for i.MX31 PDK yet, so we rely on some other
- * program to initialize the SDRAM.
- */
+#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)

?#define CONFIG_SKIP_LOWLEVEL_INIT

include/configs/mx31pdk.h +2 -0
+#define CONFIG_SKIP_RELOCATE_UBOOT
+#endif

?/*
?* Size of malloc() pool

include/configs/mx31pdk.h +15 -0
@@ -159,4 +159,19 @@
 
 ?#define CONFIG_ENV_SIZE ? ? ? ? ? ? ? ?(128 * 1024)
 
+/* NAND configuration for the NAND_SPL */
+
+/* Start copying real U-boot from the second page */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS ? ?0x800
+#define CONFIG_SYS_NAND_U_BOOT_SIZE ? ?0x30000
+/* Load U-Boot to this address */
+#define CONFIG_SYS_NAND_U_BOOT_DST ? ? 0x87f00000
+#define CONFIG_SYS_NAND_U_BOOT_START ? CONFIG_SYS_NAND_U_BOOT_DST
+
+#define CONFIG_SYS_NAND_PAGE_SIZE ? ? ?0x800
+#define CONFIG_SYS_NAND_BLOCK_SIZE ? ? (128 * 1024)
+#define CONFIG_SYS_NAND_PAGE_COUNT ? ? 64
+#define CONFIG_SYS_NAND_SIZE ? ? ? ? ? (256 * 1024 * 1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS ?0
+

?#endif /* __CONFIG_H */

nand_spl/board/freescale/mx31pdk/Makefile new file +54 -0
new file mode 100644
index 0000000..a9572ba
@@ -0,0 +1,54 @@
+CONFIG_NAND_SPL ? ? ? ?= y
+
+include $(TOPDIR)/config.mk
+include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk
+
+LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds
+LDFLAGS ? ? ? ?= -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS)
+AFLAGS += -DCONFIG_PRELOADER -DCONFIG_NAND_SPL
+CFLAGS += -DCONFIG_PRELOADER -DCONFIG_NAND_SPL
+
+SOBJS ?= start.o lowlevel_init.o
+COBJS ?= nand_boot_fsl_nfc.o
+
+SRCS ? := $(SRCTREE)/nand_spl/nand_boot_fsl_nfc.c
+SRCS ? += $(SRCTREE)/cpu/arm1136/start.S
+SRCS ? += $(SRCTREE)/board/freescale/mx31pdk/lowlevel_init.S
+OBJS ? := $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS := $(SOBJS) $(COBJS)
+LNDIR ?:= $(OBJTREE)/nand_spl/board/$(BOARDDIR)
+
+nandobj ? ? ? ?:= $(OBJTREE)/nand_spl/
+
+ALL ? ?= $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+
+all: ? $(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
+ ? ? ? $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@
+
+$(nandobj)u-boot-spl.bin: ? ? ?$(nandobj)u-boot-spl
+ ? ? ? $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl: ?$(OBJS)
+ ? ? ? cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
+ ? ? ? ? ? ? ? -Map $(nandobj)u-boot-spl.map \
+ ? ? ? ? ? ? ? -o $@
+
+#########################################################################
+
+$(obj)%.o: ? ? $(SRCTREE)/cpu/arm1136/%.S
+ ? ? ? $(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o: ? ? $(SRCTREE)/board/freescale/mx31pdk/%.S
+ ? ? ? $(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o: ? ? $(SRCTREE)/nand_spl/%.c
+ ? ? ? $(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
nand_spl/board/freescale/mx31pdk/config.mk new file +5 -0
new file mode 100644
index 0000000..198cafc
@@ -0,0 +1,5 @@
+PAD_TO := 2048
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
nand_spl/board/freescale/mx31pdk/u-boot.lds new file +36 -1
new file mode 100644
index 0000000..edd8430
@@ -0,0 +1,36 @@
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ ? ? ? . = 0x00000000;
+
+ ? ? ? . = ALIGN(4);
+ ? ? ? .text :
+ ? ? ? {
+ ? ? ? ? ? ? ? start.o ? ? ? ? ? ? ? ? (.text)
+ ? ? ? ? ? ? ? lowlevel_init.o ? ? ? ? (.text)
+ ? ? ? ? ? ? ? nand_boot_fsl_nfc.o ? ? (.text)
+ ? ? ? ? ? ? ? *(.text)
+ ? ? ? ? ? ? ? . = 2K;
+ ? ? ? }
+
+ ? ? ? . = ALIGN(4);
+ ? ? ? .rodata : { *(.rodata) }
+
+ ? ? ? . = ALIGN(4);
+ ? ? ? .data : { *(.data) }
+
+ ? ? ? . = ALIGN(4);
+ ? ? ? .got : { *(.got) }
+
+ ? ? ? . = .;
+ ? ? ? __u_boot_cmd_start = .;
+ ? ? ? .u_boot_cmd : { *(.u_boot_cmd) }
+ ? ? ? __u_boot_cmd_end = .;
+
+ ? ? ? . = ALIGN(4);
+ ? ? ? __bss_start = .;
+ ? ? ? .bss : { *(.bss) }
+ ? ? ? _end = .;
+}
--

1.5.6

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#8 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

Quoted 4 lines · Magnus Lilja

Jean-Christpohe,

Seems like you missed the last part in my series, could you apply this one as well?

I've not I've ask Fabio ack before continue the review as you put it as board Maintainer

Best Regards,
J.

#9 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

2009/6/29 Jean-Christophe PLAGNIOL-VILLARD <[email protected]>:

Quoted 7 lines · Magnus Lilja
Quoted 4 lines

Jean-Christpohe,

Seems like you missed the last part in my series, could you apply this one as well?

I've not I've ask Fabio ack before continue the review as you put it as board Maintainer

Ah, ok. I wouldn't mind if you had continued the review while you were at it, I thought you were just waiting for his ACK before adding the last two patches. I could've fixed any issues in the meantime.

/Magnus

#10 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

In reply to Magnus Lilja
Quoted 34 lines · Magnus Lilja
---
 MAKEALL                                     |    1 +
 Makefile                                    |   14 +++-
 board/freescale/mx31pdk/config.mk           |    4 +
 board/freescale/mx31pdk/lowlevel_init.S     |  114 +++++++++++++++++++++++++++
 include/asm-arm/arch-mx31/mx31-regs.h       |   54 +++++++++++++
 include/configs/mx31pdk.h                   |   21 ++++-
 nand_spl/board/freescale/mx31pdk/Makefile   |   54 +++++++++++++
 nand_spl/board/freescale/mx31pdk/config.mk  |    5 +
 nand_spl/board/freescale/mx31pdk/u-boot.lds |   36 +++++++++
 9 files changed, 297 insertions(+), 6 deletions(-)
 create mode 100644 board/freescale/mx31pdk/lowlevel_init.S
 create mode 100644 nand_spl/board/freescale/mx31pdk/Makefile
 create mode 100644 nand_spl/board/freescale/mx31pdk/config.mk
 create mode 100644 nand_spl/board/freescale/mx31pdk/u-boot.lds
MAKEALL +1 -0
index 0757064..1f7cab4 100755
@@ -553,6 +553,7 @@ LIST_ARM11="			\
 	imx31_phycore_eet	\
 	mx31ads			\
 	mx31pdk			\
+	mx31pdk_nand		\
 	qong			\
 	smdk6400		\
 "
Makefile +0 -0
index e445e51..29d1f22 100644

Makefile $(LDSCRIPT): depend · line 379

Quoted 5 lines
Makefile +1 -1
@@ -376,7 +376,7 @@ $(LDSCRIPT):	depend
 $(NAND_SPL):	$(TIMESTAMP_FILE) $(VERSION_FILE) $(obj)include/autoconf.mk
 		$(MAKE) -C nand_spl/board/$(BOARDDIR) all
 
-$(U_BOOT_NAND):	$(NAND_SPL) $(obj)u-boot.bin
+$(U_BOOT_NAND):	$(NAND_SPL) $(obj)u-boot.bin $(obj)include/autoconf.mk

I still does not understand this as NAND_SPL already depend on $(obj)include/autoconf.mk

Makefile imx31_phycore_config : unconfig · line 3120

Quoted 10 lines
Makefile +2 -0
 		cat $(obj)nand_spl/u-boot-spl-16k.bin $(obj)u-boot.bin > $(obj)u-boot-nand.bin
 
 $(ONENAND_IPL):	$(TIMESTAMP_FILE) $(VERSION_FILE) $(obj)include/autoconf.mk
@@ -3115,8 +3115,16 @@ imx31_phycore_config	: unconfig
 mx31ads_config		: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm1136 mx31ads freescale mx31
 
 
+
+.globl lowlevel_init

why twice??

Quoted 13 lines
Makefile +13 -0
+
+#include <asm/arch/mx31-regs.h>
+#include <asm/macro.h>
+
+#define CCM_CCMR_SETUP		0x074B0BF5
+#define CCM_PDR0_SETUP_532MHZ	(PDR0_CSI_PODF(0x1ff) | PDR0_PER_PODF(7) | \
+				 PDR0_HSP_PODF(3) | PDR0_NFC_PODF(5) |     \
+				 PDR0_IPG_PODF(1) | PDR0_MAX_PODF(3) |     \
+				 PDR0_MCU_PODF(0))
+#define CCM_MPCTL_SETUP_532MHZ	(PLL_PD(0) | PLL_MFD(51) | PLL_MFI(10) |   \
+				 PLL_MFN(12))
+
+#define ESDMISC_MDDR_SETUP	0x00000004

Makefile imx31_phycore_config : unconfig

Quoted 10 lines
Makefile +10 -0
+#define ESDMISC_MDDR_RESET_DL	0x0000000c
+#define ESDCFG0_MDDR_SETUP	0x006ac73a
+
+#define ESDCTL_ROW_COL		(ESDCTL_SDE | ESDCTL_ROW(2) | ESDCTL_COL(2))
+#define ESDCTL_SETTINGS		(ESDCTL_ROW_COL | ESDCTL_SREFR(3) | \
+				 ESDCTL_DSIZ(2) | ESDCTL_BL(1))
+#define ESDCTL_PRECHARGE	(ESDCTL_ROW_COL | ESDCTL_CMD_PRECHARGE)
+#define ESDCTL_AUTOREFRESH	(ESDCTL_ROW_COL | ESDCTL_CMD_AUTOREFRESH)
+#define ESDCTL_LOADMODEREG	(ESDCTL_ROW_COL | ESDCTL_CMD_LOADMODEREG)
+#define ESDCTL_RW		ESDCTL_SETTINGS

those macro need to move too config.h

Quoted 7 lines
Makefile +7 -0
+
+.globl lowlevel_init
+lowlevel_init:
+	/* Also setup the Peripheral Port Remap register inside the core */
+	ldr	r0, =ARM_PPMRR      /* start from AIPS 2GB region */
+	mcr	p15, 0, r0, c15, c2, 4
+

<snip>

Quoted 13 lines
Makefile +7 -0
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
nand_spl/board/freescale/mx31pdk/config.mk new file +0 -0
new file mode 100644
index 0000000..198cafc

nand_spl/board/freescale/mx31pdk/config.mk line 5

Quoted 5 lines
nand_spl/board/freescale/mx31pdk/config.mk new file +5 -0
@@ -0,0 +1,5 @@
+PAD_TO	:= 2048
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif

I do not think it's board specific

Best Regards,
J.

#11 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

Hi

2009/6/29 Jean-Christophe PLAGNIOL-VILLARD <[email protected]>:

Quoted 38 lines · Magnus Lilja
Quoted 37 lines

---

?MAKEALL ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? | ? ?1 +
?Makefile ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| ? 14 +++-
?board/freescale/mx31pdk/config.mk ? ? ? ? ? | ? ?4 +
?board/freescale/mx31pdk/lowlevel_init.S ? ? | ?114 +++++++++++++++++++++++++++
?include/asm-arm/arch-mx31/mx31-regs.h ? ? ? | ? 54 +++++++++++++
?include/configs/mx31pdk.h ? ? ? ? ? ? ? ? ? | ? 21 ++++-
?nand_spl/board/freescale/mx31pdk/Makefile ? | ? 54 +++++++++++++
?nand_spl/board/freescale/mx31pdk/config.mk ?| ? ?5 +
?nand_spl/board/freescale/mx31pdk/u-boot.lds | ? 36 +++++++++

?9 files changed, 297 insertions(+), 6 deletions(-) ?create mode 100644 board/freescale/mx31pdk/lowlevel_init.S ?create mode 100644 nand_spl/board/freescale/mx31pdk/Makefile ?create mode 100644 nand_spl/board/freescale/mx31pdk/config.mk ?create mode 100644 nand_spl/board/freescale/mx31pdk/u-boot.lds

MAKEALL +1 -0
index 0757064..1f7cab4 100755
@@ -553,6 +553,7 @@ LIST_ARM11=" ? ? ? ? ? ? ? ? ? ? ?\
 ? ? ? imx31_phycore_eet ? ? ? \
 ? ? ? mx31ads ? ? ? ? ? ? ? ? \
 ? ? ? mx31pdk ? ? ? ? ? ? ? ? \
+ ? ? mx31pdk_nand ? ? ? ? ? ?\
 ? ? ? qong ? ? ? ? ? ? ? ? ? ?\
 ? ? ? smdk6400 ? ? ? ? ? ? ? ?\

?"

Makefile +0 -0
index e445e51..29d1f22 100644
@@ -376,7 +376,7 @@ $(LDSCRIPT): ? ? ?depend

?$(NAND_SPL): $(TIMESTAMP_FILE) $(VERSION_FILE) $(obj)include/autoconf.mk ? ? ? ? ? ? ? $(MAKE) -C nand_spl/board/$(BOARDDIR) all

Quoted 3 lines
Quoted 2 lines

-$(U_BOOT_NAND): ? ? ?$(NAND_SPL) $(obj)u-boot.bin +$(U_BOOT_NAND): ? ? ?$(NAND_SPL) $(obj)u-boot.bin $(obj)include/autoconf.mk

I still does not understand this as NAND_SPL already depend on $(obj)include/autoconf.mk

I can remove that, as you say NAND_SPL depends on it already.

Quoted 11 lines
Quoted 10 lines

? ? ? ? ? ? ? cat $(obj)nand_spl/u-boot-spl-16k.bin $(obj)u-boot.bin > $(obj)u-boot-nand.bin

?$(ONENAND_IPL): ? ? ?$(TIMESTAMP_FILE) $(VERSION_FILE) $(obj)include/autoconf.mk

Makefile +0 -0
@@ -3115,8 +3115,16 @@ imx31_phycore_config ? : unconfig

?mx31ads_config ? ? ? ? ? ? ? : unconfig
? ? ? @$(MKCONFIG) $(@:_config=) arm arm1136 mx31ads freescale mx31

+
+.globl lowlevel_init

why twice??

Obviously because I missed that there was one present already. I'll remove.

Quoted 16 lines
Quoted 16 lines
Makefile +16 -0
+
+#include <asm/arch/mx31-regs.h>
+#include <asm/macro.h>
+
+#define CCM_CCMR_SETUP ? ? ? ? ? ? ? 0x074B0BF5
+#define CCM_PDR0_SETUP_532MHZ ? ? ? ?(PDR0_CSI_PODF(0x1ff) | PDR0_PER_PODF(7) | \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_HSP_PODF(3) | PDR0_NFC_PODF(5) | ? ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_IPG_PODF(1) | PDR0_MAX_PODF(3) | ? ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_MCU_PODF(0))
+#define CCM_MPCTL_SETUP_532MHZ ? ? ? (PLL_PD(0) | PLL_MFD(51) | PLL_MFI(10) | ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PLL_MFN(12))
+
+#define ESDMISC_MDDR_SETUP ? 0x00000004
+#define ESDMISC_MDDR_RESET_DL ? ? ? ?0x0000000c
+#define ESDCFG0_MDDR_SETUP ? 0x006ac73a
+
Quoted 8 lines

Makefile

Quoted 7 lines
Makefile +7 -0
+#define ESDCTL_ROW_COL ? ? ? ? ? ? ? (ESDCTL_SDE | ESDCTL_ROW(2) | ESDCTL_COL(2))
+#define ESDCTL_SETTINGS ? ? ? ? ? ? ?(ESDCTL_ROW_COL | ESDCTL_SREFR(3) | \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?ESDCTL_DSIZ(2) | ESDCTL_BL(1))
+#define ESDCTL_PRECHARGE ? ? (ESDCTL_ROW_COL | ESDCTL_CMD_PRECHARGE)
+#define ESDCTL_AUTOREFRESH ? (ESDCTL_ROW_COL | ESDCTL_CMD_AUTOREFRESH)
+#define ESDCTL_LOADMODEREG ? (ESDCTL_ROW_COL | ESDCTL_CMD_LOADMODEREG)
+#define ESDCTL_RW ? ? ? ? ? ?ESDCTL_SETTINGS

those macro need to move too config.h

Why? These are specific to this board and only used within this file.

Quoted 19 lines
Quoted 7 lines
Makefile +7 -0
+
+.globl lowlevel_init
+lowlevel_init:
+ ? ? /* Also setup the Peripheral Port Remap register inside the core */
+ ? ? ldr ? ? r0, =ARM_PPMRR ? ? ?/* start from AIPS 2GB region */
+ ? ? mcr ? ? p15, 0, r0, c15, c2, 4
+

<snip>

Quoted 11 lines
Makefile +7 -0
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
nand_spl/board/freescale/mx31pdk/config.mk new file +0 -1
new file mode 100644
index 0000000..198cafc
--- /dev/null
Quoted 8 lines

nand_spl/board/freescale/mx31pdk/config.mk line 5

Quoted 7 lines

+++ b/nand_spl/board/freescale/mx31pdk/config.mk

nand_spl/board/freescale/mx31pdk/config.mk new file +5 -0
@@ -0,0 +1,5 @@
+PAD_TO ? ? ? := 2048
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif

I do not think it's board specific

And what does that comment mean? Should I remove this, move it to another file or what?

I would've appreciated receiving these comments at the same time you reviewed the other patches in the series, that would give me more time to update this.

Thanks, Magnus

#12 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

Quoted 25 lines
Quoted 16 lines
Quoted 16 lines
(quoted diff) +16 -0
+
+#include <asm/arch/mx31-regs.h>
+#include <asm/macro.h>
+
+#define CCM_CCMR_SETUP ? ? ? ? ? ? ? 0x074B0BF5
+#define CCM_PDR0_SETUP_532MHZ ? ? ? ?(PDR0_CSI_PODF(0x1ff) | PDR0_PER_PODF(7) | \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_HSP_PODF(3) | PDR0_NFC_PODF(5) | ? ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_IPG_PODF(1) | PDR0_MAX_PODF(3) | ? ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_MCU_PODF(0))
+#define CCM_MPCTL_SETUP_532MHZ ? ? ? (PLL_PD(0) | PLL_MFD(51) | PLL_MFI(10) | ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PLL_MFN(12))
+
+#define ESDMISC_MDDR_SETUP ? 0x00000004
+#define ESDMISC_MDDR_RESET_DL ? ? ? ?0x0000000c
+#define ESDCFG0_MDDR_SETUP ? 0x006ac73a
+
Quoted 8 lines

Review

Quoted 7 lines
(quoted diff) +7 -0
+#define ESDCTL_ROW_COL ? ? ? ? ? ? ? (ESDCTL_SDE | ESDCTL_ROW(2) | ESDCTL_COL(2))
+#define ESDCTL_SETTINGS ? ? ? ? ? ? ?(ESDCTL_ROW_COL | ESDCTL_SREFR(3) | \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?ESDCTL_DSIZ(2) | ESDCTL_BL(1))
+#define ESDCTL_PRECHARGE ? ? (ESDCTL_ROW_COL | ESDCTL_CMD_PRECHARGE)
+#define ESDCTL_AUTOREFRESH ? (ESDCTL_ROW_COL | ESDCTL_CMD_AUTOREFRESH)
+#define ESDCTL_LOADMODEREG ? (ESDCTL_ROW_COL | ESDCTL_CMD_LOADMODEREG)
+#define ESDCTL_RW ? ? ? ? ? ?ESDCTL_SETTINGS

those macro need to move too config.h

Quoted 1 line

Why? These are specific to this board and only used within this file.

yes but they are config so it's make sense to put with config and not in the code as we do everytime
and a lot's of time we see that the code can be shared but not the define

Quoted 29 lines
Quoted 20 lines
Quoted 8 lines
board/freescale/mx31pdk/lowlevel_init.S new file +7 -0
+
+.globl lowlevel_init
+lowlevel_init:
+ ? ? /* Also setup the Peripheral Port Remap register inside the core */
+ ? ? ldr ? ? r0, =ARM_PPMRR ? ? ?/* start from AIPS 2GB region */
+ ? ? mcr ? ? p15, 0, r0, c15, c2, 4
+

<snip>

Quoted 11 lines
nand_spl/board/freescale/mx31pdk/Makefile new file +7 -0
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
nand_spl/board/freescale/mx31pdk/config.mk new file +0 -1
new file mode 100644
index 0000000..198cafc
--- /dev/null
Quoted 8 lines

nand_spl/board/freescale/mx31pdk/config.mk line 5

Quoted 7 lines

+++ b/nand_spl/board/freescale/mx31pdk/config.mk

nand_spl/board/freescale/mx31pdk/config.mk new file +5 -0
@@ -0,0 +1,5 @@
+PAD_TO ? ? ? := 2048
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif

I do not think it's board specific

Quoted 3 lines

And what does that comment mean? Should I remove this, move it to another file or what?

Personnaly I'll active it manually in the file not via a CPPFLAGS as it will result to active all bebug

Scott what do you think?

Best Regards,
J.

#13 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

Hi

2009/6/30 Jean-Christophe PLAGNIOL-VILLARD <[email protected]>:

Quoted 25 lines
Quoted 25 lines
Quoted 24 lines
Quoted 13 lines
(quoted diff) +13 -0
+
+#include <asm/arch/mx31-regs.h>
+#include <asm/macro.h>
+
+#define CCM_CCMR_SETUP ? ? ? ? ? ? ? 0x074B0BF5
+#define CCM_PDR0_SETUP_532MHZ ? ? ? ?(PDR0_CSI_PODF(0x1ff) | PDR0_PER_PODF(7) | \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_HSP_PODF(3) | PDR0_NFC_PODF(5) | ? ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_IPG_PODF(1) | PDR0_MAX_PODF(3) | ? ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_MCU_PODF(0))
+#define CCM_MPCTL_SETUP_532MHZ ? ? ? (PLL_PD(0) | PLL_MFD(51) | PLL_MFI(10) | ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PLL_MFN(12))
+
+#define ESDMISC_MDDR_SETUP ? 0x00000004

Review

Quoted 10 lines
(quoted diff) +10 -0
+#define ESDMISC_MDDR_RESET_DL ? ? ? ?0x0000000c
+#define ESDCFG0_MDDR_SETUP ? 0x006ac73a
+
+#define ESDCTL_ROW_COL ? ? ? ? ? ? ? (ESDCTL_SDE | ESDCTL_ROW(2) | ESDCTL_COL(2))
+#define ESDCTL_SETTINGS ? ? ? ? ? ? ?(ESDCTL_ROW_COL | ESDCTL_SREFR(3) | \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?ESDCTL_DSIZ(2) | ESDCTL_BL(1))
+#define ESDCTL_PRECHARGE ? ? (ESDCTL_ROW_COL | ESDCTL_CMD_PRECHARGE)
+#define ESDCTL_AUTOREFRESH ? (ESDCTL_ROW_COL | ESDCTL_CMD_AUTOREFRESH)
+#define ESDCTL_LOADMODEREG ? (ESDCTL_ROW_COL | ESDCTL_CMD_LOADMODEREG)
+#define ESDCTL_RW ? ? ? ? ? ?ESDCTL_SETTINGS

those macro need to move too config.h

Quoted 4 lines
Quoted 1 line

Why? These are specific to this board and only used within this file.

yes but they are config so it's make sense to put with config and not in the code as we do everytime
and a lot's of time we see that the code can be shared but not the define

So you mean that it should be placed in include/configs/mx31pdk.h?

Quoted 10 lines
Quoted 10 lines
Quoted 9 lines

nand_spl/board/freescale/mx31pdk/config.mk line 5

Quoted 8 lines
nand_spl/board/freescale/mx31pdk/config.mk new file +5 -0
@@ -0,0 +1,5 @@
+PAD_TO ? ? ? := 2048
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif

I do not think it's board specific

Quoted 5 lines
Quoted 3 lines

And what does that comment mean? Should I remove this, move it to another file or what?

Personnaly I'll active it manually in the file not via a CPPFLAGS as it will result to active all bebug

Yes, I think I can agree on that. So I'll remove the debug stuff from config.mk.

Regards, Magnus

#14 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

Quoted 28 lines · Magnus Lilja

Hi

2009/6/30 Jean-Christophe PLAGNIOL-VILLARD <[email protected]>:

Quoted 25 lines
Quoted 25 lines
Quoted 24 lines
Quoted 13 lines
(quoted diff) +13 -0
+
+#include <asm/arch/mx31-regs.h>
+#include <asm/macro.h>
+
+#define CCM_CCMR_SETUP ? ? ? ? ? ? ? 0x074B0BF5
+#define CCM_PDR0_SETUP_532MHZ ? ? ? ?(PDR0_CSI_PODF(0x1ff) | PDR0_PER_PODF(7) | \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_HSP_PODF(3) | PDR0_NFC_PODF(5) | ? ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_IPG_PODF(1) | PDR0_MAX_PODF(3) | ? ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PDR0_MCU_PODF(0))
+#define CCM_MPCTL_SETUP_532MHZ ? ? ? (PLL_PD(0) | PLL_MFD(51) | PLL_MFI(10) | ? \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PLL_MFN(12))
+
+#define ESDMISC_MDDR_SETUP ? 0x00000004

Review

Quoted 10 lines
(quoted diff) +10 -0
+#define ESDMISC_MDDR_RESET_DL ? ? ? ?0x0000000c
+#define ESDCFG0_MDDR_SETUP ? 0x006ac73a
+
+#define ESDCTL_ROW_COL ? ? ? ? ? ? ? (ESDCTL_SDE | ESDCTL_ROW(2) | ESDCTL_COL(2))
+#define ESDCTL_SETTINGS ? ? ? ? ? ? ?(ESDCTL_ROW_COL | ESDCTL_SREFR(3) | \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?ESDCTL_DSIZ(2) | ESDCTL_BL(1))
+#define ESDCTL_PRECHARGE ? ? (ESDCTL_ROW_COL | ESDCTL_CMD_PRECHARGE)
+#define ESDCTL_AUTOREFRESH ? (ESDCTL_ROW_COL | ESDCTL_CMD_AUTOREFRESH)
+#define ESDCTL_LOADMODEREG ? (ESDCTL_ROW_COL | ESDCTL_CMD_LOADMODEREG)
+#define ESDCTL_RW ? ? ? ? ? ?ESDCTL_SETTINGS

those macro need to move too config.h

Quoted 6 lines
Quoted 4 lines
Quoted 1 line

Why? These are specific to this board and only used within this file.

yes but they are config so it's make sense to put with config and not in the code as we do everytime
and a lot's of time we see that the code can be shared but not the define

So you mean that it should be placed in include/configs/mx31pdk.h?

yes

Best Regards,
J.

#15 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

In reply to Jean-Christophe PLAGNIOL-VILLARD
Quoted 11 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 7 lines
Quoted 4 lines

nand_spl/board/freescale/mx31pdk/config.mk line 5

Quoted 3 lines
nand_spl/board/freescale/mx31pdk/config.mk new file +3 -0
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif

I do not think it's board specific

And what does that comment mean? Should I remove this, move it to another file or what?

Personnaly I'll active it manually in the file not via a CPPFLAGS as it will result to active all bebug

Scott what do you think?

I don't think we should do anything differently from the rest of U-Boot here.

-Scott

#16 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

Hi

2009/6/30 Scott Wood <[email protected]>:

Quoted 11 lines
Quoted 10 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 10 lines
Quoted 6 lines

nand_spl/board/freescale/mx31pdk/config.mk line 5

Quoted 4 lines
nand_spl/board/freescale/mx31pdk/config.mk new file +3 -0
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif

I do not think it's board specific

And what does that comment mean? Should I remove this, move it to another file or what?

Quoted 7 lines
Quoted 4 lines

Personnaly I'll active it manually in the file not via a CPPFLAGS as it will result to active all bebug

Scott what do you think?

I don't think we should do anything differently from the rest of U-Boot here.

Well, that's not easy since the rest of U-boot does it in different ways, i.e. some boards have the debug stuff and some don't. As an example all boards in nand_spl/board/{amcc,samsung}/* have that while the rest don't have it.

Regards, Magnus Lilja

#17 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

Quoted 19 lines · Magnus Lilja

Hi

2009/6/30 Scott Wood <[email protected]>:

Quoted 16 lines
Quoted 14 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 10 lines
Quoted 6 lines

nand_spl/board/freescale/mx31pdk/config.mk line 5

Quoted 4 lines
nand_spl/board/freescale/mx31pdk/config.mk new file +3 -0
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif

I do not think it's board specific

And what does that comment mean? Should I remove this, move it to another file or what?

Personnaly I'll active it manually in the file not via a CPPFLAGS as it will result to active all bebug

Scott what do you think?

Quoted 7 lines
Quoted 2 lines

I don't think we should do anything differently from the rest of U-Boot here.

Well, that's not easy since the rest of U-boot does it in different ways, i.e. some boards have the debug stuff and some don't. As an example all boards in nand_spl/board/{amcc,samsung}/* have that while the rest don't have it.

so we need a common rule
IMHO define it manually in each file you want to debug make more sense

Scoot for you?

Best Regards,
J.

#18 lore raw

PATCH v4 6/6 MX31: Add NAND SPL boot support to i.MX31 PDK board.

Quoted 11 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 7 lines
Quoted 3 lines
Quoted 1 line

Scott what do you think?

I don't think we should do anything differently from the rest of U-Boot here.

Well, that's not easy since the rest of U-boot does it in different ways, i.e. some boards have the debug stuff and some don't. As an example all boards in nand_spl/board/{amcc,samsung}/* have that while the rest don't have it.

so we need a common rule
IMHO define it manually in each file you want to debug make more sense

Scoot for you?

If we want to have something makefile based it should be done consistently throughout u-boot. If we're not going to do that, then I agree, do it manually inside each file you want to debug.

-Scott

#19 lore raw

PATCH v4 5/6 MX31: Add basic support for Freescale i.MX31 PDK board.

In reply to Magnus Lilja
Quoted 26 lines · Magnus Lilja

Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).

This patch assumes that some other program performs the actual NAND boot.

---
 MAINTAINERS                           |    4 +
 MAKEALL                               |    1 +
 Makefile                              |    3 +
 board/freescale/mx31pdk/Makefile      |   52 +++++++++++
 board/freescale/mx31pdk/config.mk     |    1 +
 board/freescale/mx31pdk/mx31pdk.c     |   63 +++++++++++++
 include/asm-arm/arch-mx31/mx31-regs.h |    2 +
 include/configs/mx31pdk.h             |  162 +++++++++++++++++++++++++++++++++
 8 files changed, 288 insertions(+), 0 deletions(-)
 create mode 100644 board/freescale/mx31pdk/Makefile
 create mode 100644 board/freescale/mx31pdk/config.mk
 create mode 100644 board/freescale/mx31pdk/mx31pdk.c
 create mode 100644 include/configs/mx31pdk.h
MAINTAINERS +0 -0
index 1f6008f..8eb54e1 100644

MAINTAINERS Thomas Elste <[email protected]> · line 534

Quoted 7 lines
MAINTAINERS +4 -0
@@ -528,6 +528,10 @@ Thomas Elste <[email protected]>
 
 	modnet50	ARM720T (NET+50)
 
+Fabio Estevam <[email protected]>
+
+	mx31pdk		i.MX31
+

Fabio could you ack it please

Quoted 67 lines
MAINTAINERS +0 -0
 Peter Figuli <[email protected]>
 
 	wepep250	xscale
MAKEALL +1 -0
index f48a08e..0757064 100755
@@ -552,6 +552,7 @@ LIST_ARM11="			\
 	imx31_phycore		\
 	imx31_phycore_eet	\
 	mx31ads			\
+	mx31pdk			\
 	qong			\
 	smdk6400		\
 "
Makefile +3 -0
index aa4646f..e445e51 100644
@@ -3115,6 +3115,9 @@ imx31_phycore_config	: unconfig
 mx31ads_config		: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm1136 mx31ads freescale mx31
 
+mx31pdk_config		: unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm1136 mx31pdk freescale mx31
+
 omap2420h4_config	: unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm1136 omap2420h4 NULL omap24xx
 
board/freescale/mx31pdk/mx31pdk.c new file +34 -0
@@ -0,0 +1,63 @@
+/*
+ *
+ * (C) Copyright 2009 Magnus Lilja <[email protected]>
+ *
+ * (c) 2007 Pengutronix, Sascha Hauer <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include <asm/arch/mx31.h>
+#include <asm/arch/mx31-regs.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{

board/freescale/mx31pdk/mx31pdk.c line 44

Quoted 10 lines
board/freescale/mx31pdk/mx31pdk.c new file +10 -0
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* CS5: CPLD incl. network controller */
+	__REG(CSCR_U(5)) = 0x0000d843;

we need to remove this __REG
ok for this time but a clean up is really needed

Best Regards,
J.

#20 lore raw

PATCH v4 5/6 MX31: Add basic support for Freescale i.MX31 PDK board.

Quoted 28 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 27 lines · Magnus Lilja

Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).

This patch assumes that some other program performs the actual NAND boot.

---
 MAINTAINERS                           |    4 +
 MAKEALL                               |    1 +
 Makefile                              |    3 +
 board/freescale/mx31pdk/Makefile      |   52 +++++++++++
 board/freescale/mx31pdk/config.mk     |    1 +
 board/freescale/mx31pdk/mx31pdk.c     |   63 +++++++++++++
 include/asm-arm/arch-mx31/mx31-regs.h |    2 +
 include/configs/mx31pdk.h             |  162 +++++++++++++++++++++++++++++++++
 8 files changed, 288 insertions(+), 0 deletions(-)
 create mode 100644 board/freescale/mx31pdk/Makefile
 create mode 100644 board/freescale/mx31pdk/config.mk
 create mode 100644 board/freescale/mx31pdk/mx31pdk.c
 create mode 100644 include/configs/mx31pdk.h
MAINTAINERS +0 -0
index 1f6008f..8eb54e1 100644
@@ -528,6 +528,10 @@ Thomas Elste <[email protected]>
 
Quoted 7 lines

MAINTAINERS Thomas Elste <[email protected]> · line 534

Quoted 6 lines
MAINTAINERS +4 -0
 	modnet50	ARM720T (NET+50)
 
+Fabio Estevam <[email protected]>
+
+	mx31pdk		i.MX31
+

Fabio could you ack it please

ping

Best Regards,
J.

#21 lore raw

PATCH v4 5/6 MX31: Add basic support for Freescale i.MX31 PDK board.

In reply to Magnus Lilja
Quoted 6 lines · Magnus Lilja

Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).

This patch assumes that some other program performs the actual NAND boot.

Quoted 14 lines
---
 MAINTAINERS                           |    4 +
 MAKEALL                               |    1 +
 Makefile                              |    3 +
 board/freescale/mx31pdk/Makefile      |   52 +++++++++++
 board/freescale/mx31pdk/config.mk     |    1 +
 board/freescale/mx31pdk/mx31pdk.c     |   63 +++++++++++++
 include/asm-arm/arch-mx31/mx31-regs.h |    2 +
 include/configs/mx31pdk.h             |  162 +++++++++++++++++++++++++++++++++
 8 files changed, 288 insertions(+), 0 deletions(-)
 create mode 100644 board/freescale/mx31pdk/Makefile
 create mode 100644 board/freescale/mx31pdk/config.mk
 create mode 100644 board/freescale/mx31pdk/mx31pdk.c
 create mode 100644 include/configs/mx31pdk.h

Applied to u-boot/arm

Best Regards,
J.

#22 lore raw

PATCH v4 4/6 i.MX31: Create a common device file.

In reply to Magnus Lilja
Quoted 8 lines · Magnus Lilja
---
 cpu/arm1136/mx31/Makefile        |    1 +
 cpu/arm1136/mx31/devices.c       |   56 ++++++++++++++++++++++++++++++++++++++
 include/asm-arm/arch-mx31/mx31.h |    3 ++
 3 files changed, 60 insertions(+), 0 deletions(-)
 create mode 100644 cpu/arm1136/mx31/devices.c

Applied to u-boot-arm

Best Regards,
J.

#23 lore raw

PATCH v4 4/6 i.MX31: Create a common device file.

Dear Jean-Christophe PLAGNIOL-VILLARD,

Quoted 10 lines · In message <[email protected]> you wrote:
Quoted 8 lines · Magnus Lilja
---
 cpu/arm1136/mx31/Makefile        |    1 +
 cpu/arm1136/mx31/devices.c       |   56 ++++++++++++++++++++++++++++++++++++++
 include/asm-arm/arch-mx31/mx31.h |    3 ++
 3 files changed, 60 insertions(+), 0 deletions(-)
 create mode 100644 cpu/arm1136/mx31/devices.c

Applied to u-boot-arm

All your postings like these seem to be missing any thread infor- mation - there is neither a "References: " nor any "In-reply-to: " header in them. This means thatit is pretty difficult to find out to which message they actually refer to.

Please make sure to configure your mailer such that it adds such "References: " headers, or use a different MUA.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The C-shell doesn't parse. It adhoculates.
    - Casper.Dik at Holland.Sun.COM in <[email protected]>
#25 lore raw

PATCH v4 3/6 ARM: Add macros.h to be used in assembler file.

In reply to Magnus Lilja

Dear Magnus Lilja,

Quoted 5 lines · In message <6fd22327241accc2efcada8380923c8e9c523790.1244918138.git.lilja.magnu…

Changes from last version: Added documentation for the macros.

 include/asm-arm/macro.h |   74 +++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 74 insertions(+), 0 deletions(-)
 create mode 100644 include/asm-arm/macro.h

Sorry for the late comment...

...

Quoted 3 lines

+/*
+ * These macros provide a convenient way to write 8, 16 and 32 bit data
+ * to any address.

I think this comment might be wrong. It should probably read "... to any _memory_ address". Using these macros to access device registers and the like is probably nore recommended?

Please comment...

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Q: What do you get when you cross an ethernet with an income statement?
A: A local area networth.
#26 lore raw

PATCH v4 3/6 ARM: Add macros.h to be used in assembler file.

Quoted 11 lines · Wolfgang Denk

Dear Magnus Lilja,

Quoted 5 lines · In message <6fd22327241accc2efcada8380923c8e9c523790.1244918138.git.lilja.magnu…

Changes from last version: Added documentation for the macros.

 include/asm-arm/macro.h |   74 +++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 74 insertions(+), 0 deletions(-)
 create mode 100644 include/asm-arm/macro.h

Sorry for the late comment...

Quoted 8 lines

...

Quoted 3 lines

+/*
+ * These macros provide a convenient way to write 8, 16 and 32 bit data
+ * to any address.

I think this comment might be wrong. It should probably read "... to any _memory_ address". Using these macros to access device registers and the like is probably nore recommended?

you can access cpu register without problem with these macros

Best Regards,
J.

#27 lore raw

PATCH v4 3/6 ARM: Add macros.h to be used in assembler file.

Dear Jean-Christophe PLAGNIOL-VILLARD,

Quoted 8 lines · In message <[email protected]> you wrote:
Quoted 7 lines
Quoted 3 lines

+ * These macros provide a convenient way to write 8, 16 and 32 bit data
+ * to any address.

I think this comment might be wrong. It should probably read "... to any _memory_ address". Using these macros to access device registers and the like is probably nore recommended?

you can access cpu register without problem with these macros

Is it guaranteed that none of the existing ARM architectures and all the plethora of their specific implementations of the zillions of SoCs do not require any form of memory barrier instructions when accessing device registers? Even when these are external peripherals on some external bus?

Sorry for such a stupid question about things that are eventually obvious to you, but I don't know ARM processors that well...

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Committee, n.:  A group of men who individually can do nothing but as
a group decide that nothing can be done.                 - Fred Allen
#28 lore raw

PATCH v4 3/6 ARM: Add macros.h to be used in assembler file.

Quoted 12 lines · Wolfgang Denk

Dear Jean-Christophe PLAGNIOL-VILLARD,

Quoted 8 lines · In message <[email protected]> you wrote:
Quoted 7 lines
Quoted 3 lines

+ * These macros provide a convenient way to write 8, 16 and 32 bit data
+ * to any address.

I think this comment might be wrong. It should probably read "... to any _memory_ address". Using these macros to access device registers and the like is probably nore recommended?

you can access cpu register without problem with these macros

Quoted 8 lines

Is it guaranteed that none of the existing ARM architectures and all the plethora of their specific implementations of the zillions of SoCs do not require any form of memory barrier instructions when accessing device registers? Even when these are external peripherals on some external bus?

Sorry for such a stupid question about things that are eventually obvious to you, but I don't know ARM processors that well...

you may need it in specific case as cache, tlb, co-processor or smp otherwise you do not need it

so normaly no-need for register access

Best Regards,
J.

#29 lore raw

PATCH v4 2/6 MX31: Add NAND SPL for i.MX31.

In reply to Magnus Lilja
Quoted 11 lines · Magnus Lilja

This patch adds the NAND SPL framework needed to boot i.MX31 boards from NAND.

It has been tested on a i.MX31 PDK board with large page NAND. Small page NANDs should work as well, but this has not been tested.

Note: The i.MX31 NFC uses a non-standard layout for large page NANDs, whether this is compatible with a particular setup depends on how the NAND device is programmed by the flash programmer (e.g. JTAG debugger).

Quoted 5 lines

The patch is based on the work by Maxim Artamonov.

---

Applied to u-boot-arm

Best Regards,
J.

#31 lore raw

v4 cover MX31: NAND boot for PDK boards.

In reply to Magnus Lilja

Hi

2009/6/13 Magnus Lilja <[email protected]>:

Quoted 4 lines

Hi all,

This is the latest set of patches that introduces NAND boot support for the i.MX31 CPU in general and the PDK board especially.

Any chance this can be merged soon? It applies on u-boot master and runs fine. u-boot-arm/next is missing an apollon patch that fixes a typo, but with that patch it applies fine on u-boot-arm/next as well.

Regards, Magnus

Quoted 65 lines

The patches apply on u-boot/next. For u-boot-arm/next I get an error from StGit when applying the CONFIG_PRELOADER patch but that's because the u-boot-arm/next is not update (as of this email). Don't know if git resolves the problem (it's the file onenand_ipl/board/apollon/Makefile that causes the problem), however after fixing that manually the u-boot-arm/next also builds fine with these patches.

This update takes of the comments received from Wolfgang Denk.

The code boots on i.MX31 PDK board using large page NAND, it should work for small page NAND as well but that has not been tested.

Regards, Magnus Lilja

Jean-Christophe PLAGNIOL-VILLARD (1):
?ARM: Add macros.h to be used in assembler file.

Magnus Lilja (5):
?ARM1136: Introduce CONFIG_PRELOADER macro. ?MX31: Add NAND SPL for i.MX31.
?i.MX31: Create a common device file.
?MX31: Add basic support for Freescale i.MX31 PDK board. ?MX31: Add NAND SPL boot support to i.MX31 PDK board.

?MAINTAINERS ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? | ? ?4 +
?MAKEALL ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? | ? ?2 +
?Makefile ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| ? 13 ++-
?README ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| ? ?5 +
?board/freescale/mx31pdk/Makefile ? ? ? ? ? ?| ? 52 ++++++
?board/freescale/mx31pdk/config.mk ? ? ? ? ? | ? ?5 +
?board/freescale/mx31pdk/lowlevel_init.S ? ? | ?114 ++++++++++++
?board/freescale/mx31pdk/mx31pdk.c ? ? ? ? ? | ? 63 +++++++
?cpu/arm1136/mx31/Makefile ? ? ? ? ? ? ? ? ? | ? ?1 +
?cpu/arm1136/mx31/devices.c ? ? ? ? ? ? ? ? ?| ? 56 ++++++
?cpu/arm1136/start.S ? ? ? ? ? ? ? ? ? ? ? ? | ? 33 ++--
?include/asm-arm/arch-mx31/mx31-regs.h ? ? ? | ? 61 +++++++
?include/asm-arm/arch-mx31/mx31.h ? ? ? ? ? ?| ? ?3 +
?include/asm-arm/macro.h ? ? ? ? ? ? ? ? ? ? | ? 74 ++++++++
?include/configs/mx31pdk.h ? ? ? ? ? ? ? ? ? | ?177 ++++++++++++++++++
?include/fsl_nfc.h ? ? ? ? ? ? ? ? ? ? ? ? ? | ?109 +++++++++++
?nand_spl/board/freescale/mx31pdk/Makefile ? | ? 54 ++++++
?nand_spl/board/freescale/mx31pdk/config.mk ?| ? ?5 +
?nand_spl/board/freescale/mx31pdk/u-boot.lds | ? 36 ++++
?nand_spl/nand_boot_fsl_nfc.c ? ? ? ? ? ? ? ?| ?259 +++++++++++++++++++++++++++
?onenand_ipl/board/apollon/Makefile ? ? ? ? ?| ? ?4 +-

?21 files changed, 1113 insertions(+), 17 deletions(-) ?create mode 100644 board/freescale/mx31pdk/Makefile ?create mode 100644 board/freescale/mx31pdk/config.mk ?create mode 100644 board/freescale/mx31pdk/lowlevel_init.S ?create mode 100644 board/freescale/mx31pdk/mx31pdk.c ?create mode 100644 cpu/arm1136/mx31/devices.c ?create mode 100644 include/asm-arm/macro.h
?create mode 100644 include/configs/mx31pdk.h
?create mode 100644 include/fsl_nfc.h
?create mode 100644 nand_spl/board/freescale/mx31pdk/Makefile ?create mode 100644 nand_spl/board/freescale/mx31pdk/config.mk ?create mode 100644 nand_spl/board/freescale/mx31pdk/u-boot.lds ?create mode 100644 nand_spl/nand_boot_fsl_nfc.c

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#32 lore raw

v4 cover MX31: NAND boot for PDK boards.

Quoted 11 lines · Magnus Lilja

Hi

2009/6/13 Magnus Lilja <[email protected]>:

Quoted 4 lines

Hi all,

This is the latest set of patches that introduces NAND boot support for the i.MX31 CPU in general and the PDK board especially.

Any chance this can be merged soon? It applies on u-boot master and runs fine. u-boot-arm/next is missing an apollon patch that fixes a typo, but with that patch it applies fine on u-boot-arm/next as well.

sorry I no time actually I'll take a llok on it this WE

Best Regards,
J.