Conexant CX20561 - Microphone problems
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)
Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
options snd-intel-hda enable_msi=1 power_save=10 power_save_controller=true model=laptop index=0
Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture
https://bugzilla.redhat.com/show_bug.cgi?id=502293
Thanks for any help,
Shawn.
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 26 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
Quoted 7 lines
options snd-intel-hda enable_msi=1 power_save=10 power_save_controller=true model=laptop index=0
Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture
https://bugzilla.redhat.com/show_bug.cgi?id=502293
Could you give alsa-info.sh output? Run with --no-upload option, and attach the generated file.
thanks,
Takashi
Quoted 32 lines · Takashi Iwai
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 29 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
options snd-intel-hda enable_msi=1 power_save=10
power_save_controller=true model=laptop index=0
Quoted 8 lines
Quoted 4 lines
Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture
https://bugzilla.redhat.com/show_bug.cgi?id=502293Could you give
alsa-info.shoutput? Run with --no-upload option, and attach the generated file.
Here's the attached output,
Thanks,
Shawn.
Quoted 9 lines
thanks,
Takashi
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
upload=true&script=true&cardinfo=
!!################################
!!ALSA Information Script v 0.4.58
!!################################
!!Script ran on: Mon Nov 2 16:35:17 UTC 2009
!!Linux Distribution
!!------------------
Debian GNU/Linux squeeze/sid \n \l
!!DMI Information
!!---------------
Manufacturer: LENOVO Product Name: 4058CTO
!!Kernel Information
!!------------------
Kernel release: 2.6.32-rc5-custom Operating System: GNU/Linux Architecture: x86_64 Processor: unknown SMP Enabled: Yes
!!ALSA Version
!!------------
Driver version: 1.0.21 Library version: 1.0.20 Utilities version: 1.0.21
!!Loaded ALSA modules
!!-------------------
snd_hda_intelsnd_usb_audio
!!Sound Servers on this system
!!----------------------------
Jack:
Installed - Yes (/usr/bin/jackd)
Running - No
!!Soundcards recognised by ALSA
!!-----------------------------
0 [Intel ]: HDA-Intel - HDA Intel
HDA Intel at 0xfc020000 irq 17
1 [Q9000 ]: USB-Audio - QuickCam Pro 9000
Logitech, Inc. QuickCam Pro 9000 at usb-0000:00:1d.7-2, high speed!!PCI Soundcards installed in the system
!!--------------------------------------
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
!!Advanced information - PCI Vendor/Device/Susbsystem ID's !!--------------------------------------------------------
00:1b.0 0403: 8086:293e (rev 03)
Subsystem: 17aa:20f2
!!Modprobe options (Sound related)
!!--------------------------------
snd-intel-hda: enable_msi=1 model=laptop index=0
snd-usb-audio: index=-2 nrpacks=1
snd-atiixp-modem: index=-2
snd-intel8x0m: index=-2
snd-via82xx-modem: index=-2
snd-pcsp: index=-2
!!Loaded sound module options
!!--------------------------
!!Module: snd_hda_intel
bdl_pos_adj : 1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1 enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y enable_msi : 0 id : <NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL> index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1 model : <NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL> position_fix : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 power_save : 0 power_save_controller : Y probe_mask : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1 probe_only : N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N single_cmd : N
!!Module: snd_usb_audio
async_unlink : Y device_setup : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y id : <NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL> ignore_ctl_error : N index : -2,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1 nrpacks : 1 pid : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1 vid : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
!!HDA-Intel Codec information
!!---------------------------
--startcollapse--
Codec: Conexant CX20561 (Hermosa)
Address: 0
Function Id: 0x1
Vendor Id: 0x14f15051
Subsystem Id: 0x17aa2100
Revision Id: 0x100000
No Modem Function Group found
Default PCM:
rates [0x160]: 44100 48000 96000
bits [0xe]: 16 20 24
formats [0x1]: PCMDefault Amp-In caps: N/A
Default Amp-Out caps: N/A
GPIO: io=4, o=0, i=0, unsolicited=1, wake=0
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x10 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L
Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=0 Amp-Out vals: [0x2c 0x2c]
Converter: stream=0, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM Power: setting=D0, actual=D0
Node 0x11 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L
Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=0 Amp-Out vals: [0x4a 0x4a]
Converter: stream=0, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM Power: setting=D0, actual=D0
Node 0x12 [Audio Output] wcaps 0x211: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:
rates [0x160]: 44100 48000 96000
bits [0xe]: 16 20 24
formats [0x5]: PCM AC3Node 0x13 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out
Amp-Out caps: ofs=0x03, nsteps=0x03, stepsize=0x17, mute=0 Amp-Out vals: [0x00]
Node 0x14 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L
Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=0 Amp-In vals: [0x38 0x38] [0x2b 0x2b]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x160]: 44100 48000 96000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power: setting=D0, actual=D0
Connection: 2
0x1d* 0x17Node 0x15 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L
Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=0 Amp-In vals: [0x3c 0x3c]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x160]: 44100 48000 96000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power: setting=D0, actual=D0
Connection: 1
0x18Node 0x16 [Pin Complex] wcaps 0x400581: Stereo
Pincap 0x0000001c: OUT HP Detect
Pin Default 0x022140f0: [Jack] HP Out at Ext Front
Conn = 1/8, Color = Green
DefAssociation = 0xf, Sequence = 0x0
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=37, enabled=1
Power: setting=D0, actual=D0
Connection: 2
0x10* 0x11
Node 0x17 [Pin Complex] wcaps 0x40048b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-In vals: [0x03 0x03]
Pincap 0x00001224: IN Detect
Vref caps: 50 80
Pin Default 0x61a190f0: [N/A] Mic at Sep Rear
Conn = 1/8, Color = Pink
DefAssociation = 0xf, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=38, enabled=1
Power: setting=D0, actual=D0
Node 0x18 [Pin Complex] wcaps 0x40048b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-In vals: [0x03 0x03]
Pincap 0x00001224: IN Detect
Vref caps: 50 80
Pin Default 0x02a190f0: [Jack] Mic at Ext Front
Conn = 1/8, Color = Pink
DefAssociation = 0xf, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=39, enabled=1
Power: setting=D0, actual=D0
Node 0x19 [Pin Complex] wcaps 0x400581: Stereo
Pincap 0x00000014: OUT Detect
Pin Default 0x40f000f0: [N/A] Other at Ext N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0xf, Sequence = 0x0
Pin-ctls: 0x40: OUT
Unsolicited: tag=37, enabled=1
Power: setting=D0, actual=D0
Connection: 2
0x10* 0x11
Node 0x1a [Pin Complex] wcaps 0x400501: Stereo
Pincap 0x00010010: OUT EAPD
EAPD 0x2: EAPD
Pin Default 0x901701f0: [Fixed] Speaker at Int N/A
Conn = Analog, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Power: setting=D0, actual=D0
Connection: 2
0x10* 0x11
Node 0x1b [Pin Complex] wcaps 0x400500: Mono
Pincap 0x00010010: OUT EAPD
EAPD 0x2: EAPD
Pin Default 0x40f001f0: [N/A] Other at Ext N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Power: setting=D0, actual=D0
Connection: 2
0x10* 0x11
Node 0x1c [Pin Complex] wcaps 0x400701: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x40f001f0: [N/A] Other at Ext N/A
Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Power: setting=D0, actual=D0
Connection: 1
0x12
Node 0x1d [Pin Complex] wcaps 0x40040b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x04, stepsize=0x2f, mute=0 Amp-In vals: [0x03 0x03]
Pincap 0x00000020: IN
Pin Default 0x90a601f0: [Fixed] Mic at Int N/A
Conn = Digital, Color = Unknown
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power: setting=D0, actual=D0
Node 0x1e [Vendor Defined Widget] wcaps 0xf00000: Mono
Codec: Conexant ID 2c06
Address: 1
Function Id: 0x2
Vendor Id: 0x14f12c06
Subsystem Id: 0x17aa2122
Revision Id: 0x100000
Modem Function Group: 0x2
--endcollapse--
!!ALSA Device nodes
!!-----------------
crw-rw----+ 1 root audio 116, 9 Nov 2 11:28 /dev/snd/controlC0 crw-rw----+ 1 root audio 116, 11 Nov 2 11:28 /dev/snd/controlC1 crw-rw----+ 1 root audio 116, 8 Nov 2 11:28 /dev/snd/hwC0D0 crw-rw----+ 1 root audio 116, 7 Nov 2 11:28 /dev/snd/hwC0D1 crw-rw----+ 1 root audio 116, 6 Nov 2 11:28 /dev/snd/pcmC0D0c crw-rw----+ 1 root audio 116, 5 Nov 2 11:35 /dev/snd/pcmC0D0p crw-rw----+ 1 root audio 116, 4 Nov 2 11:28 /dev/snd/pcmC0D1p crw-rw----+ 1 root audio 116, 10 Nov 2 11:28 /dev/snd/pcmC1D0c crw-rw----+ 1 root audio 116, 3 Nov 2 11:28 /dev/snd/seq crw-rw----+ 1 root audio 116, 2 Nov 2 11:28 /dev/snd/timer
/dev/snd/by-id:
total 0
drwxr-xr-x 2 root root 60 Nov 2 11:28 . drwxr-xr-x 4 root root 280 Nov 2 11:28 .. lrwxrwxrwx 1 root root 12 Nov 2 11:28 usb-046d_0990_B4261720-02 -> ../controlC1
/dev/snd/by-path:
total 0
drwxr-xr-x 2 root root 80 Nov 2 11:28 . drwxr-xr-x 4 root root 280 Nov 2 11:28 .. lrwxrwxrwx 1 root root 12 Nov 2 11:28 pci-0000:00:1b.0 -> ../controlC0 lrwxrwxrwx 1 root root 12 Nov 2 11:28 pci-0000:00:1d.7-usb-0:2:1.2 -> ../controlC1
!!Aplay/Arecord output
!!------------
APLAY
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: CONEXANT Analog [CONEXANT Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 1: Conexant Digital [Conexant Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
ARECORD
**** List of CAPTURE Hardware Devices ****
card 0: Intel [HDA Intel], device 0: CONEXANT Analog [CONEXANT Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: Q9000 [QuickCam Pro 9000], device 0: USB Audio [USB Audio]
Subdevices: 1/1
Subdevice #0: subdevice #0
!!Amixer output
!!-------------
!!-------Mixer controls for card 0 [Intel]
Card hw:0 'Intel'/'HDA Intel at 0xfc020000 irq 17'
Mixer name : 'Conexant CX20561 (Hermosa)'
Components : 'HDA:14f15051,17aa2100,00100000 HDA:14f12c06,17aa2122,00100000'
Controls : 15
Simple ctrls : 8
Simple mixer control 'Master',0
Capabilities: pvolume pswitch pswitch-joined Playback channels: Front Left - Front Right
Limits: Playback 0 - 74
Mono:
Front Left: Playback 44 [59%] [-30.00dB] [on] Front Right: Playback 44 [59%] [-30.00dB] [on]
Simple mixer control 'PCM',0
Capabilities: pvolume
Playback channels: Front Left - Front Right
Limits: Playback 0 - 255
Mono:
Front Left: Playback 250 [98%] [-1.00dB] Front Right: Playback 250 [98%] [-1.00dB]
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958 Default PCM',0
Capabilities: pswitch pswitch-joined Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'Digital',0
Capabilities: cvolume
Capture channels: Front Left - Front Right
Limits: Capture 0 - 120
Front Left: Capture 65 [54%] [2.50dB] Front Right: Capture 65 [54%] [2.50dB]
Simple mixer control 'Docking Mic',0
Capabilities: volume pswitch
Playback channels: Front Left - Front Right Capture channels: Front Left - Front Right
Limits: 0 - 80
Front Left: 60 [75%] [-14.00dB] Playback [on] Front Right: 60 [75%] [-14.00dB] Playback [on]
Simple mixer control 'External Mic',0
Capabilities: volume pswitch
Playback channels: Front Left - Front Right Capture channels: Front Left - Front Right
Limits: 0 - 80
Front Left: 43 [54%] [-31.00dB] Playback [on] Front Right: 43 [54%] [-31.00dB] Playback [on]
Simple mixer control 'Internal Mic',0
Capabilities: volume pswitch
Playback channels: Front Left - Front Right Capture channels: Front Left - Front Right
Limits: 0 - 80
Front Left: 56 [70%] [-18.00dB] Playback [on] Front Right: 56 [70%] [-18.00dB] Playback [on]
!!-------Mixer controls for card 1 [Q9000]
Card hw:1 'Q9000'/'Logitech, Inc. QuickCam Pro 9000 at usb-0000:00:1d.7-2, high speed'
Mixer name : 'USB Mixer'
Components : 'USB046d:0990'
Controls : 2
Simple ctrls : 1
Simple mixer control 'Mic',0
Capabilities: cvolume cvolume-joined cswitch cswitch-joined
Capture channels: Mono
Limits: Capture 0 - 3072
Mono: Capture 0 [0%] [on]
!!Alsactl output
!!-------------
--startcollapse--
state.Intel {
control.1 {
comment.access 'read write'
comment.type INTEGER
comment.count 2
comment.range '0 - 80'
comment.dbmin -7400
comment.dbmax 600
iface MIXER
name 'Internal Mic Volume'
value.0 56
value.1 56
}
control.2 {
comment.access 'read write'
comment.type BOOLEAN
comment.count 2
iface MIXER
name 'Internal Mic Switch'
value.0 true
value.1 true
}
control.3 {
comment.access 'read write'
comment.type INTEGER
comment.count 2
comment.range '0 - 80'
comment.dbmin -7400
comment.dbmax 600
iface MIXER
name 'External Mic Volume'
value.0 43
value.1 43
}
control.4 {
comment.access 'read write'
comment.type BOOLEAN
comment.count 2
iface MIXER
name 'External Mic Switch'
value.0 true
value.1 true
}
control.5 {
comment.access 'read write'
comment.type INTEGER
comment.count 2
comment.range '0 - 80'
comment.dbmin -7400
comment.dbmax 600
iface MIXER
name 'Docking Mic Volume'
value.0 60
value.1 60
}
control.6 {
comment.access 'read write'
comment.type BOOLEAN
comment.count 2
iface MIXER
name 'Docking Mic Switch'
value.0 true
value.1 true
}
control.7 {
comment.access 'read write'
comment.type INTEGER
comment.count 2
comment.range '0 - 74'
comment.dbmin -7400
comment.dbmax 0
iface MIXER
name 'Master Playback Volume'
value.0 44
value.1 44
}
control.8 {
comment.access 'read write'
comment.type BOOLEAN
comment.count 1
iface MIXER
name 'Master Playback Switch'
value true
}
control.9 {
comment.access read
comment.type IEC958
comment.count 1
iface MIXER
name 'IEC958 Playback Con Mask'
value '0fff000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
}
control.10 {
comment.access read
comment.type IEC958
comment.count 1
iface MIXER
name 'IEC958 Playback Pro Mask'
value '0f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
}
control.11 {
comment.access 'read write'
comment.type IEC958
comment.count 1
iface MIXER
name 'IEC958 Playback Default'
value '0400000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
}
control.12 {
comment.access 'read write'
comment.type BOOLEAN
comment.count 1
iface MIXER
name 'IEC958 Playback Switch'
value false
}
control.13 {
comment.access 'read write'
comment.type BOOLEAN
comment.count 1
iface MIXER
name 'IEC958 Default PCM Playback Switch'
value true
}
control.14 {
comment.access 'read write user'
comment.type INTEGER
comment.count 2
comment.range '0 - 255'
comment.tlv '0000000100000008ffffec1400000014'
comment.dbmin -5100
comment.dbmax 0
iface MIXER
name 'PCM Playback Volume'
value.0 250
value.1 250
}
control.15 {
comment.access 'read write user'
comment.type INTEGER
comment.count 2
comment.range '0 - 120'
comment.tlv '0000000100000008fffff44800000032'
comment.dbmin -3000
comment.dbmax 3000
iface MIXER
name 'Digital Capture Volume'
value.0 65
value.1 65
}
}
state.Q9000 {
control.1 {
comment.access 'read write'
comment.type BOOLEAN
comment.count 1
iface MIXER
name 'Mic Capture Switch'
value true
}
control.2 {
comment.access 'read write'
comment.type INTEGER
comment.count 1
comment.range '0 - 3072'
iface MIXER
name 'Mic Capture Volume'
value 0
}
}--endcollapse--
!!All Loaded Modules
!!------------------
Module
cryptdaes_x86_64aes_generic
fbcon
tileblit
font
bitblit
softcursor
i915drm_kms_helper
drmi2c_algo_bit
vboxnetadp
vboxnetflt
vboxdrv
coretempfirewire_sbp2snd_hda_codec_conexantsnd_hda_intelsnd_hda_codecsnd_usb_audiosnd_pcm_osssnd_mixer_osssnd_pcm
arc4snd_seq_dummysnd_usb_libsnd_hwdepsnd_seq_osssnd_seq_midisnd_rawmidi
iwlagnsnd_seq_midi_eventsnd_seq
iwlcore
mac80211snd_timer
cfg80211
pcmciasnd_seq_devicei2c_i801
joydev
snd
uvcvideo
videodevv4l1_compatv4l2_compat_ioctl32
soundcorethinkpad_acpiyenta_socketrsrc_nonstaticpcmcia_coresnd_page_alloc
nvram
psmouseserio_raw
usbhidfirewire_ohcifirewire_corecrc_itu_t
ohci1394ricoh_mmc
ieee1394sdhci_pci
sdhciled_class
e1000e
video
outputintel_agp
!!Sysfs Files
!!-----------
/sys/class/sound/hwC0D0/init_pin_configs:0x16 0x022140f00x17 0x61a190f00x18 0x02a190f00x19 0x40f000f00x1a 0x901701f00x1b 0x40f001f00x1c 0x40f001f00x1d 0x90a601f0
/sys/class/sound/hwC0D0/driver_pin_configs:
/sys/class/sound/hwC0D0/user_pin_configs:
/sys/class/sound/hwC0D0/init_verbs:
/sys/class/sound/hwC0D1/init_pin_configs:0x73 0x016a10f0
/sys/class/sound/hwC0D1/driver_pin_configs:
/sys/class/sound/hwC0D1/user_pin_configs:
/sys/class/sound/hwC0D1/init_verbs:
!!ALSA/HDA dmesg
!!------------------
[ 6.184325] phy0: Selected rate control algorithm 'iwl-agn-rs' [ 6.348894] HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 6.349044] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 6.533734] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9 [ 6.533893] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10 [ 6.534031] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11 [ 6.534169] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 6.651462] usbcore: registered new interface driver snd-usb-audio
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
At Mon, 2 Nov 2009 11:36:21 -0500,
Quoted 36 lines · Shawn Starr
Quoted 34 lines · Takashi Iwai
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 31 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
options snd-intel-hda enable_msi=1 power_save=10
power_save_controller=true model=laptop index=0Assuming power saving/controller causes the microphone to cut out or not.
Quoted 7 lines
Quoted 6 lines
Quoted 2 lines
3) I'm now aware that this card has no pinouts for PCM capture
https://bugzilla.redhat.com/show_bug.cgi?id=502293Could you give
alsa-info.shoutput? Run with --no-upload option, and attach the generated file.Here's the attached output,
Judging from the pin config, in your case, "Docking" seems controlling the external-mic volume. The "External Mic Volume" should be zero.
Takashi
Quoted 43 lines · Takashi Iwai
At Mon, 2 Nov 2009 11:36:21 -0500,
Quoted 40 lines · Shawn Starr
Quoted 39 lines · Takashi Iwai
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 35 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
options snd-intel-hda enable_msi=1 power_save=10
power_save_controller=true model=laptop index=0Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture
https://bugzilla.redhat.com/show_bug.cgi?id=502293
Quoted 8 lines
Quoted 4 lines
Quoted 2 lines
Could you give
alsa-info.shoutput? Run with --no-upload option, and attach the generated file.Here's the attached output,
Judging from the pin config, in your case, "Docking" seems controlling the external-mic volume. The "External Mic Volume" should be zero.
There is still problems with the volume sensitivity, but I will adjust to set ext mic to zero. Do we need a quirk for the Lenovo W500 then?
Or that's a bug wrt to volume sensitivity and static interferences?
Thanks,
Shawn.
Quoted 7 lines
Takashi
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
At Tue, 3 Nov 2009 14:30:15 -0500,
Quoted 48 lines · Shawn Starr
Quoted 46 lines · Takashi Iwai
At Mon, 2 Nov 2009 11:36:21 -0500,
Quoted 43 lines · Shawn Starr
Quoted 41 lines · Takashi Iwai
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 27 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
Quoted 8 lines
options snd-intel-hda enable_msi=1 power_save=10
power_save_controller=true model=laptop index=0Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture
https://bugzilla.redhat.com/show_bug.cgi?id=502293Could you give
alsa-info.shoutput? Run with --no-upload option, and attach the generated file.
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
Here's the attached output,
Judging from the pin config, in your case, "Docking" seems controlling the external-mic volume. The "External Mic Volume" should be zero.
There is still problems with the volume sensitivity, but I will adjust to set ext mic to zero. Do we need a quirk for the Lenovo W500 then?
Looks so. Though, the SSID is identical with X200. I'm wondering whether X200 works fine as is or not...
Quoted 1 line
Or that's a bug wrt to volume sensitivity and static interferences?
The mic boost volumes are missing in these quirks. You can adjust manually via hda-verb, e.g.
hda-verb /dev/snd/hwC0D0 0x1d SET_AMP 0x7003
for the built-in mic, and
hda-verb /dev/snd/hwC0D0 0x18 SET_AMP 0x7003
for the mic jack. Change the value between 0x7000 and 0x7004.
Takashi
Quoted 68 lines · Takashi Iwai
At Tue, 3 Nov 2009 14:30:15 -0500,
Quoted 47 lines · Shawn Starr
Quoted 46 lines · Takashi Iwai
At Mon, 2 Nov 2009 11:36:21 -0500,
Quoted 43 lines · Shawn Starr
Quoted 41 lines · Takashi Iwai
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 27 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
Quoted 8 lines
options snd-intel-hda enable_msi=1 power_save=10
power_save_controller=true model=laptop index=0Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture
https://bugzilla.redhat.com/show_bug.cgi?id=502293Could you give
alsa-info.shoutput? Run with --no-upload option, and attach the generated file.Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Here's the attached output,
Judging from the pin config, in your case, "Docking" seems controlling the external-mic volume. The "External Mic Volume" should be zero.
There is still problems with the volume sensitivity, but I will adjust to set ext mic to zero. Do we need a quirk for the Lenovo W500 then?
Looks so. Though, the SSID is identical with X200. I'm wondering whether X200 works fine as is or not...
Quoted 1 line
Or that's a bug wrt to volume sensitivity and static interferences?
The mic boost volumes are missing in these quirks. You can adjust manually via hda-verb, e.g.
hda-verb /dev/snd/hwC0D0 0x1d SET_AMP 0x7003
Quoted 8 lines
for the built-in mic, and
hda-verb /dev/snd/hwC0D0 0x18 SET_AMP 0x7003for the mic jack. Change the value between
0x7000and0x7004.Takashi
Will try to adjust those. I tried the X200, but it didn't make any difference.
Thanks,
Shawn.
Quoted 5 lines
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 74 lines · Shawn Starr
Quoted 73 lines · Takashi Iwai
At Tue, 3 Nov 2009 14:30:15 -0500,
Quoted 47 lines · Shawn Starr
Quoted 46 lines · Takashi Iwai
At Mon, 2 Nov 2009 11:36:21 -0500,
Quoted 43 lines · Shawn Starr
Quoted 41 lines · Takashi Iwai
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 27 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
Quoted 8 lines
options snd-intel-hda enable_msi=1 power_save=10
power_save_controller=true model=laptop index=0Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture
https://bugzilla.redhat.com/show_bug.cgi?id=502293Could you give
alsa-info.shoutput? Run with --no-upload option, and attach the generated file.Quoted 8 lines
Quoted 5 lines
Quoted 1 line
Here's the attached output,
Judging from the pin config, in your case, "Docking" seems controlling the external-mic volume. The "External Mic Volume" should be zero.
There is still problems with the volume sensitivity, but I will adjust to set ext mic to zero. Do we need a quirk for the Lenovo W500 then?
Looks so. Though, the SSID is identical with X200. I'm wondering whether X200 works fine as is or not...
Quoted 1 line
Or that's a bug wrt to volume sensitivity and static interferences?
The mic boost volumes are missing in these quirks. You can adjust manually via hda-verb, e.g.
hda-verb /dev/snd/hwC0D0 0x1d SET_AMP 0x7003for the built-in mic, and
hda-verb /dev/snd/hwC0D0 0x18 SET_AMP 0x7003
Quoted 8 lines
Quoted 4 lines
for the mic jack. Change the value between
0x7000and0x7004.Takashi
Will try to adjust those. I tried the X200, but it didn't make any
difference.
I set the mic boost volume quirk, that did adjust the loudness, so it doesn't seem to be cutting out anymore. So it looks like that problem is fixed with the quirk.
Would you like me to provide you a sound recording indicating the interference I hear when using the microphone?
Thanks,
Shawn.
Quoted 13 lines
Thanks,
Shawn.Quoted 4 lines
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 84 lines · Shawn Starr
Quoted 75 lines · Shawn Starr
Quoted 74 lines · Takashi Iwai
At Tue, 3 Nov 2009 14:30:15 -0500,
Quoted 49 lines · Shawn Starr
Quoted 48 lines · Takashi Iwai
At Mon, 2 Nov 2009 11:36:21 -0500,
Quoted 44 lines · Shawn Starr
Quoted 33 lines · Takashi Iwai
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 30 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
options snd-intel-hda enable_msi=1 power_save=10 power_save_controller=true model=laptop index=0
Quoted 8 lines
Quoted 5 lines
Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture https://bugzilla.redhat.com/show_bug.cgi?id=502293
Could you give
alsa-info.shoutput? Run with --no-upload option, and attach the generated file.Here's the attached output,
Quoted 7 lines
Quoted 3 lines
Judging from the pin config, in your case, "Docking" seems controlling the external-mic volume. The "External Mic Volume" should be zero.
There is still problems with the volume sensitivity, but I will adjust to set ext mic to zero. Do we need a quirk for the Lenovo W500 then?
Looks so. Though, the SSID is identical with X200. I'm wondering whether X200 works fine as is or not...
Quoted 1 line
Or that's a bug wrt to volume sensitivity and static interferences?
The mic boost volumes are missing in these quirks. You can adjust manually via hda-verb, e.g.
hda-verb /dev/snd/hwC0D0 0x1d SET_AMP 0x7003for the built-in mic, and
hda-verb /dev/snd/hwC0D0 0x18 SET_AMP 0x7003Quoted 7 lines
Quoted 4 lines
for the mic jack. Change the value between
0x7000and0x7004.Takashi
Will try to adjust those. I tried the X200, but it didn't make any
difference.
Quoted 7 lines
I set the mic boost volume quirk, that did adjust the loudness, so it
doesn't seem to be cutting out anymore. So it looks like that problem is fixed with the quirk.Would you like me to provide you a sound recording indicating the
interference I hear when using the microphone?
The interference is coming from: ALSA Capture on default (seems to be the digital device), yet HDA Intel [CONEXANT Analog] has no such interference.
I suppose I could make an .asoundrc and force default to use the Analog device vs the digital one.
Quoted 21 lines
Thanks,
Shawn.Quoted 8 lines
Thanks,
Shawn.Quoted 4 lines
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-develQuoted 4 lines
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
At Thu, 5 Nov 2009 04:26:49 -0500,
Quoted 90 lines · Shawn Starr
Quoted 88 lines · Shawn Starr
Quoted 75 lines · Shawn Starr
Quoted 74 lines · Takashi Iwai
At Tue, 3 Nov 2009 14:30:15 -0500,
Quoted 49 lines · Shawn Starr
Quoted 48 lines · Takashi Iwai
At Mon, 2 Nov 2009 11:36:21 -0500,
Quoted 44 lines · Shawn Starr
Quoted 33 lines · Takashi Iwai
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 30 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
options snd-intel-hda enable_msi=1 power_save=10 power_save_controller=true model=laptop index=0
Quoted 8 lines
Quoted 5 lines
Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture https://bugzilla.redhat.com/show_bug.cgi?id=502293
Could you give
alsa-info.shoutput? Run with --no-upload option, and attach the generated file.Here's the attached output,
Quoted 7 lines
Quoted 3 lines
Judging from the pin config, in your case, "Docking" seems controlling the external-mic volume. The "External Mic Volume" should be zero.
There is still problems with the volume sensitivity, but I will adjust to set ext mic to zero. Do we need a quirk for the Lenovo W500 then?
Looks so. Though, the SSID is identical with X200. I'm wondering whether X200 works fine as is or not...
Quoted 1 line
Or that's a bug wrt to volume sensitivity and static interferences?
The mic boost volumes are missing in these quirks. You can adjust manually via hda-verb, e.g.
hda-verb /dev/snd/hwC0D0 0x1d SET_AMP 0x7003for the built-in mic, and
hda-verb /dev/snd/hwC0D0 0x18 SET_AMP 0x7003Quoted 7 lines
Quoted 4 lines
for the mic jack. Change the value between
0x7000and0x7004.Takashi
Will try to adjust those. I tried the X200, but it didn't make any
difference.I set the mic boost volume quirk, that did adjust the loudness, so it
doesn't seem to be cutting out anymore. So it looks like that problem is fixed with the quirk.
Quoted 5 lines
Quoted 3 lines
Would you like me to provide you a sound recording indicating the
interference I hear when using the microphone?The interference is coming from: ALSA Capture on default (seems to be the digital device), yet HDA Intel [CONEXANT Analog] has no such interference.
I don't understand what you mean here at all....
Takashi
A message that is not in the archive (sent off-list or not yet received): [email protected]
At Thu, 5 Nov 2009 06:34:36 -0500,
Quoted 12 lines · Shawn Starr
Quoted 7 lines
Quoted 4 lines
The interference is coming from: ALSA Capture on default (seems to be the digital device), yet HDA Intel [CONEXANT Analog] has no such interference.
I don't understand what you mean here at all....
I'm not understanding what 'default' is in this case. How many capture
(microphone) inputs does this device have? It really seems strange to me
that one capture input has so much interference. I just don't know what it is using.
Quoted 4 lines
**** List of CAPTURE Hardware Devices ****
card 0: Intel [HDA Intel], device 0: CONEXANT Analog [CONEXANT Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
So, you have only this PCM stream for capture.
Quoted 7 lines
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: CONEXANT Analog [CONEXANT Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 1: Conexant Digital [Conexant Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
These are for playback, not capture.
Takashi
At Thu, 5 Nov 2009 03:48:37 -0500,
Quoted 72 lines · Shawn Starr
Quoted 70 lines · Takashi Iwai
At Tue, 3 Nov 2009 14:30:15 -0500,
Quoted 47 lines · Shawn Starr
Quoted 46 lines · Takashi Iwai
At Mon, 2 Nov 2009 11:36:21 -0500,
Quoted 43 lines · Shawn Starr
Quoted 41 lines · Takashi Iwai
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 27 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
Quoted 8 lines
options snd-intel-hda enable_msi=1 power_save=10
power_save_controller=true model=laptop index=0Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture
https://bugzilla.redhat.com/show_bug.cgi?id=502293Could you give
alsa-info.shoutput? Run with --no-upload option, and attach the generated file.Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Here's the attached output,
Judging from the pin config, in your case, "Docking" seems controlling the external-mic volume. The "External Mic Volume" should be zero.
There is still problems with the volume sensitivity, but I will adjust to set ext mic to zero. Do we need a quirk for the Lenovo W500 then?
Looks so. Though, the SSID is identical with X200. I'm wondering whether X200 works fine as is or not...
Quoted 1 line
Or that's a bug wrt to volume sensitivity and static interferences?
The mic boost volumes are missing in these quirks. You can adjust manually via hda-verb, e.g.
hda-verb /dev/snd/hwC0D0 0x1d SET_AMP 0x7003for the built-in mic, and
Quoted 7 lines
Quoted 6 lines
hda-verb /dev/snd/hwC0D0 0x18 SET_AMP 0x7003for the mic jack. Change the value between
0x7000and0x7004.Takashi
Will try to adjust those. I tried the X200, but it didn't make any difference.
So you have Lenovo X200 laptop, too?
That's nice, so we can avoid the regression if we change the x200 quirk code.
Takashi
Quoted 43 lines · Takashi Iwai
At Mon, 2 Nov 2009 11:36:21 -0500,
Quoted 40 lines · Shawn Starr
Quoted 39 lines · Takashi Iwai
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 35 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
options snd-intel-hda enable_msi=1 power_save=10
power_save_controller=true model=laptop index=0Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture
https://bugzilla.redhat.com/show_bug.cgi?id=502293
Quoted 9 lines
Quoted 5 lines
Quoted 3 lines
Could you give
alsa-info.shoutput? Run with --no-upload option, and
attach the generated file.Here's the attached output,
Judging from the pin config, in your case, "Docking" seems controlling the external-mic volume. The "External Mic Volume" should be zero.
alsacontrol shows two 'Internal Mic' options and two 'Docking Mic' options, no External Mic option visible?
Now using: 2.6.39-0.rc3.git2.0.fc16.x86_64
While this laptop can use a docking port, I have none, although the BIOS does give an option to enable docking ports, I guess those don't do anything unless you actually dock the laptop?
Shawn.
Quoted 6 lines
Takashi
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
At Mon, 18 Apr 2011 19:40:26 -0400,
Quoted 55 lines · Shawn Starr
Quoted 43 lines · Takashi Iwai
At Mon, 2 Nov 2009 11:36:21 -0500,
Quoted 40 lines · Shawn Starr
Quoted 39 lines · Takashi Iwai
At Thu, 29 Oct 2009 18:59:40 -0400,
Quoted 35 lines · Shawn Starr
Hello ALSA developers,
I am having problems with the microphone on the following hardware this is on a Lenovo W500 laptop.
Card: HDA Intel
Chip: Conexant CX20561 (Hermosa)Here is the problems im noticing:
1) If I use ALSA 'default' with the microphone I get noise interference on output [high/low/high/low].
If I switch this to use the "ALSA Capture on HDA Intel [CONEXANT Analog] I get interference except it is the standard 60Hz electrical noise [steady noise]
2) Using the internal/external microphones gives an inconsistent volume. It also does not seem to work with the microphone cutting out so much. I need to adjust Digital + another microphone but it still drops capturing.
Alsamixer shows: Digital/Docking Microphone/External Microphone/Internal Microphone
Here is the module options I give to the sound driver:
options snd-intel-hda enable_msi=1 power_save=10
power_save_controller=true model=laptop index=0Assuming power saving/controller causes the microphone to cut out or not.
3) I'm now aware that this card has no pinouts for PCM capture
https://bugzilla.redhat.com/show_bug.cgi?id=502293Quoted 9 lines
Quoted 5 lines
Quoted 3 lines
Could you give
alsa-info.shoutput? Run with --no-upload option, and
attach the generated file.Here's the attached output,
Judging from the pin config, in your case, "Docking" seems controlling the external-mic volume. The "External Mic Volume" should be zero.
Quoted 8 lines
alsacontrol shows two 'Internal Mic' options and two 'Docking Mic' options, no External Mic option visible?
Now using: 2.6.39-0.rc3.git2.0.fc16.x86_64
While this laptop can use a docking port, I have none, although the BIOS does give an option to enable docking ports, I guess those don't do anything unless you actually dock the laptop?
Just try model=hp. This corresponds to a model without the docking-station.
Takashi