Add support for the Dallas/Maxim DS1705
Subsystems (2)
PATCH 5/5 Add support for the Dallas/Maxim DS1705
Basically it's the same as the original DS17 but much faster.
--- Documentation/hwmon/lm75 | 8 ++++---- drivers/hwmon/Kconfig | 2 +- drivers/hwmon/lm75.c | 7 +++++++ 3 files changed, 12 insertions(+), 5 deletions(-)
Documentation/hwmon/lm75 +4 -4
@@ -12,11 +12,11 @@ Supported chips: Addresses scanned: I2C 0x48 - 0x4f Datasheet: Publicly available at the National Semiconductor website http://www.national.com/ - * Dallas Semiconductor DS75, DS1775 - Prefixes: 'ds75', 'ds1775' + * Dallas Semiconductor (now Maxim) DS75, DS1775, DS7505 + Prefixes: 'ds75', 'ds1775', 'ds7505' Addresses scanned: none - Datasheet: Publicly available at the Dallas Semiconductor website - http://www.maxim-ic.com/ + Datasheet: Publicly available at the Maxim website + http://www.maximintegrated.com/ * Maxim MAX6625, MAX6626 Prefixes: 'max6625', 'max6626' Addresses scanned: none
drivers/hwmon/Kconfig +1 -1
@@ -588,7 +588,7 @@ config SENSORS_LM75 temperature sensor chip, with models including: - Analog Devices ADT75 - - Dallas Semiconductor DS75 and DS1775 + - Dallas Semiconductor DS75, DS1775 and DS7505 - Maxim MAX6625 and MAX6626 - Microchip MCP980x - National Semiconductor LM75, LM75A
drivers/hwmon/lm75.c +7 -0
@@ -38,6 +38,7 @@ enum lm75_type { /* keep sorted in alph adt75, ds1775, ds75, + ds7505, lm75, lm75a, max6625,
@@ -202,6 +203,11 @@ lm75_probe(struct i2c_client *client, co data->resolution =11 ; data->sample_time =HZ ;break ; +case ds7505: + set_mask |=3 <<5 ;/* 12-bit mode */ + data->resolution =12 ; + data->sample_time =HZ /4 ; +break ;case lm75:case lm75a: data->resolution =9 ;
@@ -289,6 +295,7 @@ static const struct i2c_device_id lm75_i { "adt75", adt75, }, { "ds1775", ds1775, }, { "ds75", ds75, }, + { "ds7505", ds7505, }, { "lm75", lm75, }, { "lm75a", lm75a, }, { "max6625", max6625, },
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Guenter Roeck
maintainerQuoted 12 lines · Jean Delvare
Basically it's the same as the original DS17 but much faster.
Signed-off-by Jean Delvare <[email protected]>--- Documentation/hwmon/lm75 | 8 ++++---- drivers/hwmon/Kconfig | 2 +- drivers/hwmon/lm75.c | 7 +++++++ 3 files changed, 12 insertions(+), 5 deletions(-)
Documentation/hwmon/lm75 Supported chips: · line 15
Quoted 6 lines
Documentation/hwmon/lm75 +1
-2@@ -12,11 +12,11 @@ Supported chips: Addresses scanned: I2C 0x48 - 0x4f Datasheet: Publicly available at the National Semiconductor website http://www.national.com/ - * Dallas Semiconductor DS75, DS1775 - Prefixes: 'ds75', 'ds1775' + * Dallas Semiconductor (now Maxim) DS75, DS1775, DS7505
Hi Jean,
Headline says DS1705. Looking into the datasheets, I guess the headline is wrong, or I am missing something.
Otherwise Acked-by: Guenter Roeck <[email protected]>
Quoted 59 lines
Documentation/hwmon/lm75 +3
-2+ Prefixes: 'ds75', 'ds1775', 'ds7505' Addresses scanned: none - Datasheet: Publicly available at the Dallas Semiconductor website - http://www.maxim-ic.com/ + Datasheet: Publicly available at the Maxim website + http://www.maximintegrated.com/ * Maxim MAX6625, MAX6626 Prefixes: 'max6625', 'max6626' Addresses scanned: nonedrivers/hwmon/Kconfig +1
-1@@ -588,7 +588,7 @@ config SENSORS_LM75 temperature sensor chip, with models including: - Analog Devices ADT75 - - Dallas Semiconductor DS75 and DS1775 + - Dallas Semiconductor DS75, DS1775 and DS7505 - Maxim MAX6625 and MAX6626 - Microchip MCP980x - National Semiconductor LM75, LM75Adrivers/hwmon/lm75.c +7
-0@@ -38,6 +38,7 @@ enum lm75_type { /* keep sorted in alph adt75, ds1775, ds75, + ds7505, lm75, lm75a, max6625,@@ -202,6 +203,11 @@ lm75_probe(struct i2c_client *client, co data->resolution =11 ; data->sample_time =HZ ;break ; +case ds7505: + set_mask |=3 <<5 ;/* 12-bit mode */ + data->resolution =12 ; + data->sample_time =HZ /4 ; +break ;case lm75:case lm75a: data->resolution =9 ;@@ -289,6 +295,7 @@ static const struct i2c_device_id lm75_i { "adt75", adt75, }, { "ds1775", ds1775, }, { "ds75", ds75, }, + { "ds7505", ds7505, }, { "lm75", lm75, }, { "lm75a", lm75a, }, { "max6625", max6625, },Signature · 7 lines
-- Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Quoted 22 lines · Guenter Roeck
Quoted 12 lines · Jean Delvare
Basically it's the same as the original DS17 but much faster.
Signed-off-by Jean Delvare <[email protected]>--- Documentation/hwmon/lm75 | 8 ++++---- drivers/hwmon/Kconfig | 2 +- drivers/hwmon/lm75.c | 7 +++++++ 3 files changed, 12 insertions(+), 5 deletions(-)Documentation/hwmon/lm75 Supported chips: · line 15
Quoted 6 lines
Documentation/hwmon/lm75 +1
-2@@ -12,11 +12,11 @@ Supported chips: Addresses scanned: I2C 0x48 - 0x4f Datasheet: Publicly available at the National Semiconductor website http://www.national.com/ - * Dallas Semiconductor DS75, DS1775 - Prefixes: 'ds75', 'ds1775' + * Dallas Semiconductor (now Maxim) DS75, DS1775, DS7505Hi Jean,
Quoted 2 lines
Headline says DS1705. Looking into the datasheets, I guess the headline is wrong, or I am missing something.
Doh, yes, typo in the headline _and_ the header comment (DS75 not DS17.) Not sure how I managed to miss both. Thanks for spotting, will resend.
Quoted 1 line
Otherwise Acked-by: Guenter Roeck <[email protected]>
BTW I'll take all these patches in my own tree if this is OK with you. Not sure why you took my previous lm75 patch (Update header inclusion) in yours.
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Guenter Roeck
maintainerQuoted 30 lines · Jean Delvare
Quoted 22 lines · Guenter Roeck
Quoted 12 lines · Jean Delvare
Basically it's the same as the original DS17 but much faster.
Signed-off-by Jean Delvare <[email protected]>--- Documentation/hwmon/lm75 | 8 ++++---- drivers/hwmon/Kconfig | 2 +- drivers/hwmon/lm75.c | 7 +++++++ 3 files changed, 12 insertions(+), 5 deletions(-)Documentation/hwmon/lm75 Supported chips: · line 15
Quoted 6 lines
Documentation/hwmon/lm75 +1
-2@@ -12,11 +12,11 @@ Supported chips: Addresses scanned: I2C 0x48 - 0x4f Datasheet: Publicly available at the National Semiconductor website http://www.national.com/ - * Dallas Semiconductor DS75, DS1775 - Prefixes: 'ds75', 'ds1775' + * Dallas Semiconductor (now Maxim) DS75, DS1775, DS7505Hi Jean,
Quoted 2 lines
Headline says DS1705. Looking into the datasheets, I guess the headline is wrong, or I am missing something.
Doh, yes, typo in the headline _and_ the header comment (DS75 not DS17.) Not sure how I managed to miss both. Thanks for spotting, will resend.
Quoted 6 lines
Quoted 1 line
Otherwise Acked-by: Guenter Roeck <[email protected]>
BTW I'll take all these patches in my own tree if this is OK with you. Not sure why you took my previous lm75 patch (Update header inclusion) in yours.
Mostly because you had asked me to handle 3.8. Maybe that was a misunderstanding. Sorry if I stepped on your feet ... want me to drop it ?
Thanks,
Guenter
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Quoted 7 lines · Guenter Roeck
Quoted 3 lines · Jean Delvare
BTW I'll take all these patches in my own tree if this is OK with you. Not sure why you took my previous lm75 patch (Update header inclusion) in yours.
Mostly because you had asked me to handle 3.8. Maybe that was a misunderstanding. Sorry if I stepped on your feet ... want me to drop it ?
Ah, yes, now I remember. But I really only meant the big RC1 push. Yes, please drop it, sorry for the confusion.
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Guenter Roeck
maintainerQuoted 6 lines · Jean Delvare
Quoted 5 lines · Guenter Roeck
Quoted 3 lines · Jean Delvare
BTW I'll take all these patches in my own tree if this is OK with you. Not sure why you took my previous lm75 patch (Update header inclusion) in yours.
Quoted 6 lines
Quoted 2 lines
Mostly because you had asked me to handle 3.8. Maybe that was a misunderstanding. Sorry if I stepped on your feet ... want me to drop it ?
Ah, yes, now I remember. But I really only meant the big RC1 push. Yes, please drop it, sorry for the confusion.
Done. Feel free to add my Reviewed-by to the patch.
Thanks,
Guenter
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors