Skip to contentSkip to conversation

dt-bindings: adxl372: Document the adxl372 I2C bindings

PATCH Applied Stefan Popa 2 participants 2 messages Sep 4, 2018 – Sep 8, 2018

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 3/3 dt-bindings: adxl372: Document the adxl372 I2C bindings

The adxl372 is designed to communicate in either SPI or I2C protocol. This patch adds the documentation of device tree bindings for adxl372 I2C.

---
 Documentation/devicetree/bindings/iio/accel/adxl372.txt | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/iio/accel/adxl372.txt +13 -2
index 9409984..a289964 100644
@@ -4,14 +4,25 @@ http://www.analog.com/media/en/technical-documentation/data-sheets/adxl372.pdf
 
 Required properties:
  - compatible : should be "adi,adxl372"
- - reg: SPI chip select number for the device
+ - reg: the I2C address or SPI chip select number for the device
+
+Required properties for SPI bus usage:
  - spi-max-frequency: Max SPI frequency to use
 
 Optional properties:
  - interrupts: interrupt mapping for IRQ as documented in
    Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
 
-Example:
+Example for a I2C device node:
+
+	accelerometer@53 {
+		compatible = "adi,adxl372";
+		reg = <0x53>;
+		interrupt-parent = <&gpio>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+Example for a SPI device node:
 
 	accelerometer@0 {
 		compatible = "adi,adxl372";
Signature · 1 line
2.7.4
maintainer Applied
#1 lore raw
Quoted 5 lines · On Tue, 4 Sep 2018 17:13:14 +0300 Stefan Popa <[email protected]> wrote:

The adxl372 is designed to communicate in either SPI or I2C protocol. This patch adds the documentation of device tree bindings for adxl372 I2C.

Applied.

Thanks,

Jonathan

Quoted 36 lines
---
 Documentation/devicetree/bindings/iio/accel/adxl372.txt | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/iio/accel/adxl372.txt +13 -2
index 9409984..a289964 100644
@@ -4,14 +4,25 @@ http://www.analog.com/media/en/technical-documentation/data-sheets/adxl372.pdf
 
 Required properties:
  - compatible : should be "adi,adxl372"
- - reg: SPI chip select number for the device
+ - reg: the I2C address or SPI chip select number for the device
+
+Required properties for SPI bus usage:
  - spi-max-frequency: Max SPI frequency to use
 
 Optional properties:
  - interrupts: interrupt mapping for IRQ as documented in
    Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
 
-Example:
+Example for a I2C device node:
+
+	accelerometer@53 {
+		compatible = "adi,adxl372";
+		reg = <0x53>;
+		interrupt-parent = <&gpio>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+Example for a SPI device node:
 
 	accelerometer@0 {
 		compatible = "adi,adxl372";