RISC-V S-mode support
v2 cover RISC-V S-mode support
This patchset allows us runing u-boot in S-mode which is useful on platforms where M-mode runtime firmware is an independent firmware and u-boot is used as last stage OS bootloader.
The patchset based upon git://git.denx.de/u-boot-riscv.git
and is tested on QEMU in both M-mode and S-mode.
For S-mode testing, we have used u-boot.bin as payload of latest BBL (at commit 6ebd0f2a46255d0c76dad3c05b16c1d154795d26) applied with following changes:
machine/emulation.c +6 -0
@@ -162,6 +162,12 @@ static inline int emulate_read_csr(int num, uintptr_t mstatus, uintptr_t* resultswitch (num) { +case CSR_MISA : + *result =read_csr (misa); +return 0 ; +case CSR_MHARTID : + *result =read_csr (mhartid); +return 0 ;case CSR_CYCLE :if (!((counteren >> (CSR_CYCLE -CSR_CYCLE )) &1 ))return -1 ;
Changes since v1:
- Rebased upon latest git://git.denx.de/u-boot-riscv.git
- Add details in cover letter for running u-boot in S-mode using BBL
Anup Patel (3):
riscv: Add kconfig option to run u-boot in S-mode
riscv: qemu: Use different SYS_TEXT_BASE for S-mode
riscv: Add S-mode defconfigs for QEMU virt machine
arch/riscv/Kconfig | 6 +++++ arch/riscv/cpu/start.S | 33 ++++++++++++++++++++++++++++ board/emulation/qemu-riscv/Kconfig | 3 ++- configs/qemu-riscv32-smode_defconfig | 10 +++++++++ configs/qemu-riscv64-smode_defconfig | 11 ++++++++++ 5 files changed, 62 insertions(+), 1 deletion(-) create mode 100644 configs/qemu-riscv32-smode_defconfig create mode 100644 configs/qemu-riscv64-smode_defconfig
Signature · 1 line
2.17.1
PATCH v2 1/3 riscv: Add kconfig option to run u-boot in S-mode
This patch adds kconfig option RISCV_SMODE to run u-boot in S-mode. When this opition is enabled we use s<xyz> CSRs instead of m<xyz> CSRs.
It is important to note that there is no equivalent S-mode CSR for misa and mhartid CSRs so we expect M-mode runtime firmware (BBL or equivalent) to emulate misa and mhartid CSR read.
Eventually, we will have patches to avoid accessing misa and mhartid from S-mode.
--- arch/riscv/Kconfig | 6 ++++++ arch/riscv/cpu/start.S | 33 +++++++++++++++++++++++++++++++++ 2 files changed, 39 insertions(+)
arch/riscv/Kconfig +6 -0
@@ -55,6 +55,12 @@ config RISCV_ISA_C config RISCV_ISA_A def_bool y +config RISCV_SMODE + bool "Run in S-Mode" + default n + help + Enable this option to build an U-Boot for RISC-V S-Mode + config 32BIT bool
arch/riscv/cpu/start.S +33 -0
@@ -39,10 +39,18 @@ _start: mv s1, a1 la t0, trap_entry +#ifdef CONFIG_RISCV_SMODE + csrw stvec, t0 +#else csrw mtvec, t0 +#endif /* mask all interrupts */ +#ifdef CONFIG_RISCV_SMODE + csrw sie, zero +#else csrw mie, zero +#endif /* Enable cache */ jal icache_enable
@@ -164,7 +172,11 @@ fix_rela_dyn: */ la t0, trap_entry add t0, t0, t6 +#ifdef CONFIG_RISCV_SMODE + csrw stvec, t0 +#else csrw mtvec, t0 +#endif clear_bss: la t0, __bss_start /* t0 <- rel __bss_start in FLASH */
@@ -236,17 +248,34 @@ trap_entry: SREG x29, 29*REGBYTES(sp) SREG x30, 30*REGBYTES(sp) SREG x31, 31*REGBYTES(sp) +#ifdef CONFIG_RISCV_SMODE + csrr a0, scause + csrr a1, sepc +#else csrr a0, mcause csrr a1, mepc +#endif mv a2, sp jal handle_trap +#ifdef CONFIG_RISCV_SMODE + csrw sepc, a0 +#else csrw mepc, a0 +#endif +#ifdef CONFIG_RISCV_SMODE +/* + * Remain in S-mode after sret + */ + li t0, SSTATUS_SPP + csrs sstatus, t0 +#else /* * Remain in M-mode after mret */ li t0, MSTATUS_MPP csrs mstatus, t0 +#endif LREG x1, 1*REGBYTES(sp) LREG x2, 2*REGBYTES(sp) LREG x3, 3*REGBYTES(sp)
@@ -279,4 +308,8 @@ trap_entry: LREG x30, 30*REGBYTES(sp) LREG x31, 31*REGBYTES(sp) addi sp, sp, 32*REGBYTES +#ifdef CONFIG_RISCV_SMODE + sret +#else mret +#endif
Signature · 1 line
2.17.1
PATCH v2 1/3 riscv: Add kconfig option to run u-boot in S-mode
Hi Anup,
Quoted 5 lines · Anup Patel
This patch adds kconfig option
RISCV_SMODEto run u-boot in S-mode. When this opition is enabled we use s<xyz> CSRs instead of m<xyz> CSRs.
Quoted 7 lines
It is important to note that there is no equivalent S-mode CSR for misa and mhartid CSRs so we expect M-mode runtime firmware (BBL or equivalent) to emulate misa and mhartid CSR read.
Eventually, we will have patches to avoid accessing misa and mhartid from S-mode.
What patches?
Quoted 11 lines
Signed-off-by Anup Patel <[email protected]>--- arch/riscv/Kconfig | 6 ++++++ arch/riscv/cpu/start.S | 33 +++++++++++++++++++++++++++++++++ 2 files changed, 39 insertions(+)arch/riscv/Kconfig +0
-0
arch/riscv/Kconfig config RISCV_ISA_C · line 60
Quoted 6 lines
arch/riscv/Kconfig +3
-0@@ -55,6 +55,12 @@ config RISCV_ISA_C config RISCV_ISA_A def_bool y +config RISCV_SMODE + bool "Run in S-Mode" + default n
nits: 'default n' is not needed
arch/riscv/Kconfig config RISCV_ISA_C · line 66
Quoted 6 lines
arch/riscv/Kconfig +3
-0+ help + Enable this option to build an U-Boot for RISC-V S-Mode + config 32BIT bool
[snip]
Other than that,
Regards,
Bin
PATCH v2 1/3 riscv: Add kconfig option to run u-boot in S-mode
Quoted 13 lines · Bin Meng
Hi Anup,
Quoted 9 lines · Anup Patel
This patch adds kconfig option
RISCV_SMODEto run u-boot in S-mode. When this opition is enabled we use s<xyz> CSRs instead of m<xyz> CSRs.It is important to note that there is no equivalent S-mode CSR for misa and mhartid CSRs so we expect M-mode runtime firmware (BBL or equivalent) to emulate misa and mhartid CSR read.
Quoted 5 lines
Quoted 3 lines
Eventually, we will have patches to avoid accessing misa and mhartid from S-mode.
What patches?
What I meant was in-future we will have more patches to avoid accessing misa and mhartid from S-mode.
I will re-phrase it.
Quoted 15 lines
Quoted 15 lines
Signed-off-by Anup Patel <[email protected]>--- arch/riscv/Kconfig | 6 ++++++ arch/riscv/cpu/start.S | 33 +++++++++++++++++++++++++++++++++ 2 files changed, 39 insertions(+)arch/riscv/Kconfig +0
-0@@ -55,6 +55,12 @@ config RISCV_ISA_C config RISCV_ISA_A def_bool y
Quoted 5 lines
arch/riscv/Kconfig config RISCV_ISA_C · line 60
Quoted 3 lines
arch/riscv/Kconfig +3
-0+config RISCV_SMODE + bool "Run in S-Mode" + default nnits: 'default n' is not needed
Sure, I will drop it.
Quoted 8 lines
arch/riscv/Kconfig config RISCV_ISA_C · line 66
Quoted 7 lines
arch/riscv/Kconfig +3
-0+ help + Enable this option to build an U-Boot for RISC-V S-Mode + config 32BIT bool
Quoted 6 lines
[snip]
Other than that,
Reviewed-by Bin Meng <[email protected]>Tested-by Bin Meng <[email protected]>
Thanks,
Anup
PATCH v2 2/3 riscv: qemu: Use different SYS_TEXT_BASE for S-mode
In reply to Anup PatelWhen u-boot runs in S-mode, the M-mode runtime firmware (BBL or equivalent) uses memory range in 0x80000000 to 0x80200000. Due to this, we cannot use 0x80000000 as SYS_TEXT_BASE when running in S-mode. Instead for S-mode, we use 0x80200000 as SYS_TEXT_BASE.
Even Linux RISC-V kernel ignores/reserves memory range 0x80000000 to 0x80200000 because it runs in S-mode.
--- board/emulation/qemu-riscv/Kconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
board/emulation/qemu-riscv/Kconfig +2 -1
@@ -13,7 +13,8 @@ config SYS_CONFIG_NAME default "qemu-riscv" config SYS_TEXT_BASE - default 0x80000000 + default 0x80000000 if !RISCV_SMODE + default 0x80200000 if RISCV_SMODE config BOARD_SPECIFIC_OPTIONS # dummy def_bool y
Signature · 1 line
2.17.1
PATCH v2 2/3 riscv: qemu: Use different SYS_TEXT_BASE for S-mode
Quoted 7 lines · Anup Patel
When u-boot runs in S-mode, the M-mode runtime firmware (BBL or equivalent) uses memory range in
0x80000000to0x80200000. Due to this, we cannot use0x80000000asSYS_TEXT_BASEwhen running in S-mode. Instead for S-mode, we use0x80200000asSYS_TEXT_BASE.
Quoted 8 lines
Even Linux RISC-V kernel ignores/reserves memory range
0x80000000to0x80200000because it runs in S-mode.Signed-off-by Anup Patel <[email protected]>--- board/emulation/qemu-riscv/Kconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
PATCH v2 3/3 riscv: Add S-mode defconfigs for QEMU virt machine
In reply to Anup PatelThis patch adds S-mode defconfigs for QEMU virt machine so that we can run u-boot in S-mode on QEMU using M-mode runtime firmware (BBL or equivalent).
--- configs/qemu-riscv32-smode_defconfig | 10 ++++++++++ configs/qemu-riscv64-smode_defconfig | 11 +++++++++++ 2 files changed, 21 insertions(+) create mode 100644 configs/qemu-riscv32-smode_defconfig create mode 100644 configs/qemu-riscv64-smode_defconfig
configs/qemu-riscv32-smode_defconfig new file +10 -0
@@ -0,0 +1,10 @@ +CONFIG_RISCV=y +CONFIG_TARGET_QEMU_VIRT=y +CONFIG_RISCV_SMODE=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_FIT=y +CONFIG_DISPLAY_CPUINFO=y +CONFIG_DISPLAY_BOARDINFO=y +# CONFIG_CMD_MII is not set +CONFIG_OF_PRIOR_STAGE=y
configs/qemu-riscv64-smode_defconfig new file +11 -0
@@ -0,0 +1,11 @@ +CONFIG_RISCV=y +CONFIG_TARGET_QEMU_VIRT=y +CONFIG_ARCH_RV64I=y +CONFIG_RISCV_SMODE=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_FIT=y +CONFIG_DISPLAY_CPUINFO=y +CONFIG_DISPLAY_BOARDINFO=y +# CONFIG_CMD_MII is not set +CONFIG_OF_PRIOR_STAGE=y
Signature · 1 line
2.17.1
PATCH v2 3/3 riscv: Add S-mode defconfigs for QEMU virt machine
Quoted 9 lines · Anup Patel
This patch adds S-mode defconfigs for QEMU virt machine so that we can run u-boot in S-mode on QEMU using M-mode runtime firmware (BBL or equivalent).
Signed-off-by Anup Patel <[email protected]>--- configs/qemu-riscv32-smode_defconfig | 10 ++++++++++ configs/qemu-riscv64-smode_defconfig | 11 +++++++++++
nits: please use the name: qemu-riscv*_smode_defconfig (_ instead of -)
Quoted 4 lines
2 files changed, 21 insertions(+) create mode 100644 configs/qemu-riscv32-smode_defconfig create mode 100644 configs/qemu-riscv64-smode_defconfig
Please update board/emulation/qemu-riscv/MAINTAINERS to include these 2 defconfigs, otherwise buildman will report warnings.
Other than that,
[snip]
Regards,
Bin
PATCH v2 3/3 riscv: Add S-mode defconfigs for QEMU virt machine
Quoted 7 lines · Bin Meng
Quoted 5 lines · Anup Patel
This patch adds S-mode defconfigs for QEMU virt machine so that we can run u-boot in S-mode on QEMU using M-mode runtime firmware (BBL or equivalent).
Quoted 6 lines
Quoted 4 lines
Signed-off-by Anup Patel <[email protected]>--- configs/qemu-riscv32-smode_defconfig | 10 ++++++++++ configs/qemu-riscv64-smode_defconfig | 11 +++++++++++nits: please use the name: qemu-riscv*_smode_defconfig (_ instead of -)
OK, I will update filename of defconfigs
Quoted 8 lines
Quoted 5 lines
2 files changed, 21 insertions(+) create mode 100644 configs/qemu-riscv32-smode_defconfig create mode 100644 configs/qemu-riscv64-smode_defconfigPlease update board/emulation/qemu-riscv/MAINTAINERS to include these 2 defconfigs, otherwise buildman will report warnings.
Sure, I will update MAINTAINERS file.
Quoted 6 lines
Other than that,
Reviewed-by Bin Meng <[email protected]>Tested-by Bin Meng <[email protected]>
Thanks,
Anup