warp7: README: Adjust the binary name after DM conversion
PATCH v2 1/1 warp7: README: Adjust the binary name after DM conversion
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.
---
Changes since v1:
- Fix all occurrances
board/warp7/README | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)
board/warp7/README +6 -6
@@ -17,7 +17,7 @@ $ make mrproper $ make warp7_config $ make -This will generate the U-Boot binary called u-boot.imx. +This will generate the U-Boot binary called u-boot-dtb.imx. Put warp7 board in USB download mode:
@@ -28,11 +28,11 @@ Connect a USB to serial adapter between the host PC and warp7 Connect a USB cable between the OTG warp7 port and the host PC -Copy u-boot.imx to the imx_usb_loader folder. +Copy u-boot-dtb.imx to the imx_usb_loader folder. -Load u-boot.imx via USB: +Load u-boot-dtb.imx via USB: -$ sudo ./imx_usb u-boot.imx +$ sudo ./imx_usb u-boot-dtb.imx Then U-Boot should start and its messages will appear in the console program.
@@ -46,9 +46,9 @@ Use the default environment variables: Run the DFU command: => dfu 0 mmc 0 -Transfer u-boot.imx that will be flashed into the eMMC: +Transfer u-boot-dtb.imx that will be flashed into the eMMC: -$ sudo dfu-util -D u-boot.imx -a boot +$ sudo dfu-util -D u-boot-dtb.imx -a boot Then on the U-Boot prompt the following message should be seen after a successful upgrade:
Signature · 1 line
2.17.1
PATCH v2 1/1 warp7: README: Adjust the binary name after DM conversion
Quoted 4 lines · Fabio Estevam
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.
Signed-off-by Fabio Estevam <[email protected]>
PATCH v2 1/1 warp7: README: Adjust the binary name after DM conversion
In reply to Fabio EstevamQuoted 4 lines · Fabio Estevam
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.
Signed-off-by Fabio Estevam <[email protected]>
oops send RB from wrong address - one more time
PATCH v2 1/1 warp7: README: Adjust the binary name after DM conversion
In reply to Fabio EstevamLe 09/02/2019 à 15:01, Fabio Estevam a écrit :
Quoted 16 lines
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.
Signed-off-by Fabio Estevam <[email protected]>---
Changes since v1:
- Fix all occurrancesboard/warp7/README | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)board/warp7/README +0
-0
board/warp7/README $ make mrproper · line 17
Quoted 1 line
board/warp7/README +0
-0@@ -17,7 +17,7 @@ $ make mrproper $ make warp7_config
Hi Fabio
Fix typo warp7_config into warp7_defconig
Quoted 34 lines
board/warp7/README +6
-6$ make -This will generate the U-Boot binary called u-boot.imx. +This will generate the U-Boot binary called u-boot-dtb.imx. Put warp7 board in USB download mode:@@ -28,11 +28,11 @@ Connect a USB to serial adapter between the host PC and warp7 Connect a USB cable between the OTG warp7 port and the host PC -Copy u-boot.imx to the imx_usb_loader folder. +Copy u-boot-dtb.imx to the imx_usb_loader folder. -Load u-boot.imx via USB: +Load u-boot-dtb.imx via USB: -$ sudo ./imx_usb u-boot.imx +$ sudo ./imx_usb u-boot-dtb.imx Then U-Boot should start and its messages will appear in the console program.@@ -46,9 +46,9 @@ Use the default environment variables: Run the DFU command: => dfu 0 mmc 0 -Transfer u-boot.imx that will be flashed into the eMMC: +Transfer u-boot-dtb.imx that will be flashed into the eMMC: -$ sudo dfu-util -D u-boot.imx -a boot +$ sudo dfu-util -D u-boot-dtb.imx -a boot Then on the U-Boot prompt the following message should be seen after a successful upgrade:
PATCH v2 1/1 warp7: README: Adjust the binary name after DM conversion
Hi Joris,
Quoted 3 lines · Joris Offouga
Hi Fabio
Fix typo
warp7_configintowarp7_defconig
make warp7_config
make
Also works fine.
I agree with you that "make warp_defconfig" is preferable and I will make such change after this one gets applied.
Thanks for your suggestion!