Skip to contentSkip to conversation

warp7: README: Adjust the binary name after DM conversion

PATCH Superseded Fabio Estevam 4 participants 5 messages Feb 9, 2019 – Feb 14, 2019

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 warp7: README: Adjust the binary name after DM conversion

After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.

---
Changes since v1:
- Fix all occurrances

 board/warp7/README | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
board/warp7/README +6 -6
index 60339da543..579bb2de38 100644
@@ -17,7 +17,7 @@ $ make mrproper
 $ make warp7_config
 $ make
 
-This will generate the U-Boot binary called u-boot.imx.
+This will generate the U-Boot binary called u-boot-dtb.imx.
 
 Put warp7 board in USB download mode: 
 
@@ -28,11 +28,11 @@ Connect a USB to serial adapter between the host PC and warp7
 
 Connect a USB cable between the OTG warp7 port and the host PC
 
-Copy u-boot.imx to the imx_usb_loader folder.
+Copy u-boot-dtb.imx to the imx_usb_loader folder.
 
-Load u-boot.imx via USB:
+Load u-boot-dtb.imx via USB:
 
-$ sudo ./imx_usb u-boot.imx
+$ sudo ./imx_usb u-boot-dtb.imx
 
 Then U-Boot should start and its messages will appear in the console program.
 
@@ -46,9 +46,9 @@ Use the default environment variables:
 Run the DFU command:
 => dfu 0 mmc 0
 
-Transfer u-boot.imx that will be flashed into the eMMC:
+Transfer u-boot-dtb.imx that will be flashed into the eMMC:
 
-$ sudo dfu-util -D u-boot.imx -a boot
+$ sudo dfu-util -D u-boot-dtb.imx -a boot
 
 Then on the U-Boot prompt the following message should be seen after a
 successful upgrade:
Signature · 1 line
2.17.1
#3 lore raw

PATCH v2 1/1 warp7: README: Adjust the binary name after DM conversion

In reply to Fabio Estevam

Le 09/02/2019 à 15:01, Fabio Estevam a écrit :

Quoted 16 lines

After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.

---
Changes since v1:
- Fix all occurrances

  board/warp7/README | 12 ++++++------
  1 file changed, 6 insertions(+), 6 deletions(-)
board/warp7/README +0 -0
index 60339da543..579bb2de38 100644

board/warp7/README $ make mrproper · line 17

Quoted 1 line
board/warp7/README +0 -0
@@ -17,7 +17,7 @@ $ make mrproper
  $ make warp7_config

Hi Fabio

Fix typo warp7_config into warp7_defconig

Quoted 34 lines
board/warp7/README +6 -6
  $ make
 
-This will generate the U-Boot binary called u-boot.imx.
+This will generate the U-Boot binary called u-boot-dtb.imx.
 
  Put warp7 board in USB download mode:
 
@@ -28,11 +28,11 @@ Connect a USB to serial adapter between the host PC and warp7
 
  Connect a USB cable between the OTG warp7 port and the host PC
 
-Copy u-boot.imx to the imx_usb_loader folder.
+Copy u-boot-dtb.imx to the imx_usb_loader folder.
 
-Load u-boot.imx via USB:
+Load u-boot-dtb.imx via USB:
 
-$ sudo ./imx_usb u-boot.imx
+$ sudo ./imx_usb u-boot-dtb.imx
 
  Then U-Boot should start and its messages will appear in the console program.
 
@@ -46,9 +46,9 @@ Use the default environment variables:
  Run the DFU command:
  => dfu 0 mmc 0
 
-Transfer u-boot.imx that will be flashed into the eMMC:
+Transfer u-boot-dtb.imx that will be flashed into the eMMC:
 
-$ sudo dfu-util -D u-boot.imx -a boot
+$ sudo dfu-util -D u-boot-dtb.imx -a boot
 
  Then on the U-Boot prompt the following message should be seen after a
  successful upgrade:
#4 lore raw

PATCH v2 1/1 warp7: README: Adjust the binary name after DM conversion

Hi Joris,

Quoted 3 lines · Joris Offouga

Hi Fabio

Fix typo warp7_config into warp7_defconig

make warp7_config
make

Also works fine.

I agree with you that "make warp_defconfig" is preferable and I will make such change after this one gets applied.

Thanks for your suggestion!