Skip to contentSkip to conversation

apalis-tk1: fixes/updates for v2019.10

PATCH New Igor Opaniuk 4 participants 19 messages Jul 31, 2019 – Aug 1, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover apalis-tk1: fixes/updates for v2019.10

Misc. fixes related to pinmux configuration (fan), default bootargs, reset reason output and power rail configuration.

Dominik Sliwa (2):
apalis-tk1/t30: colibri_t30: display reset reason
apalis-tk1: remove non-esential power rails on boot

Igor Opaniuk (5):
apalis-tk1: set apalis gpio 8 aka fan_en
apalis-tk1: provide proper USB vendor id
apalis-tk1: enable user debug by default
apalis-tk1: add pcie_aspm=off to defargs
apalis-tk1: switch to zImage

Marcel Ziswiler (2):
apalis-tk1: do not explicitly release reset_moci#
apalis-tk1: remove default vesa vga mode from vidargs

 arch/arm/mach-tegra/sys_info.c                | 32 ++++++++-----
 arch/arm/mach-tegra/tegra124/cpu.c            | 45 +++++++++++++++++++
 board/toradex/apalis-tk1/apalis-tk1.c         | 10 +++++
 board/toradex/apalis-tk1/as3722_init.c        | 23 ++++++++++
 .../apalis-tk1/pinmux-config-apalis-tk1.h     |  2 +-
 configs/apalis-tk1_defconfig                  |  2 +-
 include/configs/apalis-tk1.h                  | 17 +++----
 7 files changed, 111 insertions(+), 20 deletions(-)
Signature · 1 line
2.17.1
#1 lore raw

PATCH 1/9 apalis-tk1: do not explicitly release reset_moci#

From: Marcel Ziswiler <[email protected]>

By keeping RESET_MOCI_CTRL low we avoid explicitly releasing RESET_MOCI#.

Please note that module hardware versions up to V1.1A will already release RESET_MOCI# in hardware coming out of reset.

Please further note that with this change the USB hub on the Apalis Evaluation board is kept in reset in U-Boot and therefore none of its ports are operational in U-Boot.

---

 board/toradex/apalis-tk1/pinmux-config-apalis-tk1.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
board/toradex/apalis-tk1/pinmux-config-apalis-tk1.h +1 -1
index 1584d9b2d3..d2d24c4391 100644
@@ -39,7 +39,7 @@ static const struct tegra_gpio_config apalis_tk1_gpio_inits[] = {
 	GPIO_INIT(R,    1,   OUT0), /* Shift_CTRL_Dir_In[1] */
 	GPIO_INIT(R,    2,   OUT0), /* Shift_CTRL_OE[3] */
 	GPIO_INIT(S,    3,   OUT0), /* Shift_CTRL_Dir_In[2] */
-	GPIO_INIT(U,    4,   OUT1),
+	GPIO_INIT(U,    4,   OUT0), /* RESET_MOCI_CTRL */
 	GPIO_INIT(W,    3,   IN),
 	GPIO_INIT(W,    5,   IN),
 	GPIO_INIT(BB,   0,  IN),
Signature · 1 line
2.17.1
#2 lore raw

PATCH 1/9 apalis-tk1: do not explicitly release reset_moci#

Quoted 9 lines · Igor Opaniuk

From: Marcel Ziswiler <[email protected]>

By keeping RESET_MOCI_CTRL low we avoid explicitly releasing RESET_MOCI#.

Please note that module hardware versions up to V1.1A will already release RESET_MOCI# in hardware coming out of reset.

Quoted 6 lines

Please further note that with this change the USB hub on the Apalis Evaluation board is kept in reset in U-Boot and therefore none of its ports are operational in U-Boot.

Quoted 25 lines

---

 board/toradex/apalis-tk1/pinmux-config-apalis-tk1.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
board/toradex/apalis-tk1/pinmux-config-apalis-tk1.h +1 -2
index 1584d9b2d3..d2d24c4391 100644
@@ -39,7 +39,7 @@ static const struct tegra_gpio_config apalis_tk1_gpio_inits[] = {
        GPIO_INIT(R,    1,   OUT0), /* Shift_CTRL_Dir_In[1] */
        GPIO_INIT(R,    2,   OUT0), /* Shift_CTRL_OE[3] */
        GPIO_INIT(S,    3,   OUT0), /* Shift_CTRL_Dir_In[2] */
-       GPIO_INIT(U,    4,   OUT1),
+       GPIO_INIT(U,    4,   OUT0), /* RESET_MOCI_CTRL */
        GPIO_INIT(W,    3,   IN),
        GPIO_INIT(W,    5,   IN),
        GPIO_INIT(BB,   0,  IN),
--

2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

Signature · 6 lines
Best regards
Oleksandr Suvorov

Toradex AG
Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500
4800 (main line)
#3 lore raw

PATCH 2/9 apalis-tk1: set apalis gpio 8 aka fan_en

In reply to Igor Opaniuk

From: Igor Opaniuk <[email protected]>

Make sure the Apalis GPIO 8 aka FAN_EN is on when using Apalis TK1 modules.

---

 board/toradex/apalis-tk1/apalis-tk1.c | 10 ++++++++++
 1 file changed, 10 insertions(+)
board/toradex/apalis-tk1/apalis-tk1.c +10 -0
index b87e9e7a3e..d57c5042dd 100644
@@ -19,6 +19,7 @@
 
 #define LAN_DEV_OFF_N	TEGRA_GPIO(O, 6)
 #define LAN_RESET_N	TEGRA_GPIO(S, 2)
+#define FAN_EN		TEGRA_GPIO(DD, 2)
 #define LAN_WAKE_N	TEGRA_GPIO(O, 5)
 #ifdef CONFIG_APALIS_TK1_PCIE_EVALBOARD_INIT
 #define PEX_PERST_N	TEGRA_GPIO(DD, 1) /* Apalis GPIO7 */
@@ -241,6 +242,15 @@ void tegra_pcie_board_port_reset(struct tegra_pcie_port *port)
 }
 #endif /* CONFIG_PCI_TEGRA */
 
+/*
+ * Enable/start PWM CPU fan
+ */
+void start_cpu_fan(void)
+{
+	gpio_request(FAN_EN, "FAN_EN");
+	gpio_direction_output(FAN_EN, 1);
+}
+
 /*
  * Backlight off before OS handover
  */
Signature · 1 line
2.17.1
#4 lore raw

PATCH 2/9 apalis-tk1: set apalis gpio 8 aka fan_en

Quoted 8 lines · Igor Opaniuk

From: Igor Opaniuk <[email protected]>

Make sure the Apalis GPIO 8 aka FAN_EN is on when using Apalis TK1 modules.

Quoted 40 lines

---

 board/toradex/apalis-tk1/apalis-tk1.c | 10 ++++++++++
 1 file changed, 10 insertions(+)
board/toradex/apalis-tk1/apalis-tk1.c +10 -1
index b87e9e7a3e..d57c5042dd 100644
@@ -19,6 +19,7 @@
 
 #define LAN_DEV_OFF_N  TEGRA_GPIO(O, 6)
 #define LAN_RESET_N    TEGRA_GPIO(S, 2)
+#define FAN_EN         TEGRA_GPIO(DD, 2)
 #define LAN_WAKE_N     TEGRA_GPIO(O, 5)
 #ifdef CONFIG_APALIS_TK1_PCIE_EVALBOARD_INIT
 #define PEX_PERST_N    TEGRA_GPIO(DD, 1) /* Apalis GPIO7 */
@@ -241,6 +242,15 @@ void tegra_pcie_board_port_reset(struct tegra_pcie_port *port)
 }
 #endif /* CONFIG_PCI_TEGRA */
 
+/*
+ * Enable/start PWM CPU fan
+ */
+void start_cpu_fan(void)
+{
+       gpio_request(FAN_EN, "FAN_EN");
+       gpio_direction_output(FAN_EN, 1);
+}
+
 /*
  * Backlight off before OS handover
  */
--

2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

Signature · 6 lines
Best regards
Oleksandr Suvorov

Toradex AG
Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500
4800 (main line)
#5 lore raw

PATCH 3/9 apalis-tk1: provide proper USB vendor id

In reply to Igor Opaniuk

From: Igor Opaniuk <[email protected]>

Use unified values for USB Product/Vendor numbers
when the config block is missing

---

 configs/apalis-tk1_defconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
configs/apalis-tk1_defconfig +1 -1
index 41f3aff149..ceefe4e86a 100644
@@ -56,7 +56,7 @@ CONFIG_USB_EHCI_TEGRA=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_MANUFACTURER="Toradex"
 CONFIG_USB_GADGET_VENDOR_NUM=0x1b67
-CONFIG_USB_GADGET_PRODUCT_NUM=0xffff
+CONFIG_USB_GADGET_PRODUCT_NUM=0x4000
 CONFIG_CI_UDC=y
 CONFIG_USB_GADGET_DOWNLOAD=y
 CONFIG_OF_LIBFDT_OVERLAY=y
Signature · 1 line
2.17.1
#6 lore raw

PATCH 3/9 apalis-tk1: provide proper USB vendor id

Quoted 8 lines · Igor Opaniuk

From: Igor Opaniuk <[email protected]>

Use unified values for USB Product/Vendor numbers
when the config block is missing

Quoted 25 lines

---

 configs/apalis-tk1_defconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
configs/apalis-tk1_defconfig +1 -2
index 41f3aff149..ceefe4e86a 100644
@@ -56,7 +56,7 @@ CONFIG_USB_EHCI_TEGRA=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_MANUFACTURER="Toradex"
 CONFIG_USB_GADGET_VENDOR_NUM=0x1b67
-CONFIG_USB_GADGET_PRODUCT_NUM=0xffff
+CONFIG_USB_GADGET_PRODUCT_NUM=0x4000
 CONFIG_CI_UDC=y
 CONFIG_USB_GADGET_DOWNLOAD=y
 CONFIG_OF_LIBFDT_OVERLAY=y
--

2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

Signature · 4 lines
Best regards

Oleksandr Suvorov
cryosay at gmail.com
#7 lore raw

PATCH 4/9 apalis-tk1: enable user debug by default

In reply to Igor Opaniuk

From: Igor Opaniuk <[email protected]>

Let the kernel print some debug messages when a user program crashes due to an exception.

---

 include/configs/apalis-tk1.h | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
include/configs/apalis-tk1.h +2 -1
index b4ddd1bdc6..efc52841d1 100644
@@ -111,7 +111,8 @@
 	"boot_file=uImage\0" \
 	"console=ttyS0\0" \
 	"defargs=lp0_vec=2064 at 0xf46ff000 core_edp_mv=1150 core_edp_ma=4000 " \
-		"usb_port_owner_info=2 lane_owner_info=6 emc_max_dvfs=0\0" \
+		"usb_port_owner_info=2 lane_owner_info=6 emc_max_dvfs=0 " \
+		"user_debug=30\0" \
 	"dfu_alt_info=" DFU_ALT_EMMC_INFO "\0" \
 	EMMC_BOOTCMD \
 	"fdt_board=eval\0" \
Signature · 1 line
2.17.1
#8 lore raw

PATCH 5/9 apalis-tk1: add pcie_aspm=off to defargs

In reply to Igor Opaniuk

From: Igor Opaniuk <[email protected]>

Disabling ASPM fixes incompatibilities with some PCIe cards

---

 include/configs/apalis-tk1.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/configs/apalis-tk1.h +1 -1
index efc52841d1..0bde1697bb 100644
@@ -112,7 +112,7 @@
 	"console=ttyS0\0" \
 	"defargs=lp0_vec=2064 at 0xf46ff000 core_edp_mv=1150 core_edp_ma=4000 " \
 		"usb_port_owner_info=2 lane_owner_info=6 emc_max_dvfs=0 " \
-		"user_debug=30\0" \
+		"user_debug=30 pcie_aspm=off\0" \
 	"dfu_alt_info=" DFU_ALT_EMMC_INFO "\0" \
 	EMMC_BOOTCMD \
 	"fdt_board=eval\0" \
Signature · 1 line
2.17.1
#9 lore raw

PATCH 5/9 apalis-tk1: add pcie_aspm=off to defargs

Quoted 7 lines · Igor Opaniuk

From: Igor Opaniuk <[email protected]>

Disabling ASPM fixes incompatibilities with some PCIe cards

Quoted 25 lines

---

 include/configs/apalis-tk1.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/configs/apalis-tk1.h +1 -2
index efc52841d1..0bde1697bb 100644
@@ -112,7 +112,7 @@
        "console=ttyS0\0" \
        "defargs=lp0_vec=2064 at 0xf46ff000 core_edp_mv=1150 core_edp_ma=4000 " \
                "usb_port_owner_info=2 lane_owner_info=6 emc_max_dvfs=0 " \
-               "user_debug=30\0" \
+               "user_debug=30 pcie_aspm=off\0" \
        "dfu_alt_info=" DFU_ALT_EMMC_INFO "\0" \
        EMMC_BOOTCMD \
        "fdt_board=eval\0" \
--

2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

Signature · 4 lines
Best regards

Oleksandr Suvorov
cryosay at gmail.com
#10 lore raw

PATCH 6/9 apalis-tk1: switch to zImage

In reply to Igor Opaniuk

From: Igor Opaniuk <[email protected]>

Switch to the generic compressed Kernel image type (zImage) instead of the U-Boot specific uImage format.

---

 include/configs/apalis-tk1.h | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
include/configs/apalis-tk1.h +6 -6
index 0bde1697bb..10f2948c62 100644
@@ -42,7 +42,7 @@
 #define DFU_ALT_EMMC_INFO	"apalis-tk1.img raw 0x0 0x500 mmcpart 1; " \
 				"boot part 0 1 mmcpart 0; " \
 				"rootfs part 0 2 mmcpart 0; " \
-				"uImage fat 0 1 mmcpart 0; " \
+				"zImage fat 0 1 mmcpart 0; " \
 				"tegra124-apalis-eval.dtb fat 0 1 mmcpart 0"
 
 #define EMMC_BOOTCMD \
@@ -54,7 +54,7 @@
 		"run emmcdtbload; " \
 		"load mmc ${emmcdev}:${emmcbootpart} ${kernel_addr_r} " \
 		"${boot_file} && run fdt_fixup && " \
-		"bootm ${kernel_addr_r} - ${dtbparam}\0" \
+		"bootz ${kernel_addr_r} - ${dtbparam}\0" \
 	"emmcbootpart=1\0" \
 	"emmcdev=0\0" \
 	"emmcdtbload=setenv dtbparam; load mmc ${emmcdev}:${emmcbootpart} " \
@@ -68,7 +68,7 @@
 	"nfsboot=pci enum; run setup; setenv bootargs ${defargs} ${nfsargs} " \
 		"${setupargs} ${vidargs}; echo Booting via DHCP/TFTP/NFS...; " \
 		"run nfsdtbload; dhcp ${kernel_addr_r} " \
-		"&& run fdt_fixup && bootm ${kernel_addr_r} - ${dtbparam}\0" \
+		"&& run fdt_fixup && bootz ${kernel_addr_r} - ${dtbparam}\0" \
 	"nfsdtbload=setenv dtbparam; tftp ${fdt_addr_r} " \
 		"${soc}-apalis-${fdt_board}.dtb " \
 		"&& setenv dtbparam ${fdt_addr_r}\0"
@@ -81,7 +81,7 @@
 		"${vidargs}; echo Booting from SD card in 8bit slot...; " \
 		"run sddtbload; load mmc ${sddev}:${sdbootpart} " \
 		"${kernel_addr_r} ${boot_file} && run fdt_fixup && " \
-		"bootm ${kernel_addr_r} - ${dtbparam}\0" \
+		"bootz ${kernel_addr_r} - ${dtbparam}\0" \
 	"sdbootpart=1\0" \
 	"sddev=1\0" \
 	"sddtbload=setenv dtbparam; load mmc ${sddev}:${sdbootpart} " \
@@ -98,7 +98,7 @@
 		"${usbargs} ${vidargs}; echo Booting from USB stick...; " \
 		"run usbdtbload; load usb ${usbdev}:${usbbootpart} " \
 		"${kernel_addr_r} ${boot_file} && run fdt_fixup && " \
-		"bootm ${kernel_addr_r} - ${dtbparam}\0" \
+		"bootz ${kernel_addr_r} - ${dtbparam}\0" \
 	"usbbootpart=1\0" \
 	"usbdev=0\0" \
 	"usbdtbload=setenv dtbparam; load usb ${usbdev}:${usbbootpart} " \
@@ -108,7 +108,7 @@
 	"usbrootpart=2\0"
 
 #define BOARD_EXTRA_ENV_SETTINGS \
-	"boot_file=uImage\0" \
+	"boot_file=zImage\0" \
 	"console=ttyS0\0" \
 	"defargs=lp0_vec=2064 at 0xf46ff000 core_edp_mv=1150 core_edp_ma=4000 " \
 		"usb_port_owner_info=2 lane_owner_info=6 emc_max_dvfs=0 " \
Signature · 1 line
2.17.1
#11 lore raw

PATCH 6/9 apalis-tk1: switch to zImage

Quoted 8 lines · Igor Opaniuk

From: Igor Opaniuk <[email protected]>

Switch to the generic compressed Kernel image type (zImage) instead of the U-Boot specific uImage format.

Quoted 70 lines

---

 include/configs/apalis-tk1.h | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
include/configs/apalis-tk1.h +6 -7
index 0bde1697bb..10f2948c62 100644
@@ -42,7 +42,7 @@
 #define DFU_ALT_EMMC_INFO      "apalis-tk1.img raw 0x0 0x500 mmcpart 1; " \
                                "boot part 0 1 mmcpart 0; " \
                                "rootfs part 0 2 mmcpart 0; " \
-                               "uImage fat 0 1 mmcpart 0; " \
+                               "zImage fat 0 1 mmcpart 0; " \
                                "tegra124-apalis-eval.dtb fat 0 1 mmcpart 0"
 
 #define EMMC_BOOTCMD \
@@ -54,7 +54,7 @@
                "run emmcdtbload; " \
                "load mmc ${emmcdev}:${emmcbootpart} ${kernel_addr_r} " \
                "${boot_file} && run fdt_fixup && " \
-               "bootm ${kernel_addr_r} - ${dtbparam}\0" \
+               "bootz ${kernel_addr_r} - ${dtbparam}\0" \
        "emmcbootpart=1\0" \
        "emmcdev=0\0" \
        "emmcdtbload=setenv dtbparam; load mmc ${emmcdev}:${emmcbootpart} " \
@@ -68,7 +68,7 @@
        "nfsboot=pci enum; run setup; setenv bootargs ${defargs} ${nfsargs} " \
                "${setupargs} ${vidargs}; echo Booting via DHCP/TFTP/NFS...; " \
                "run nfsdtbload; dhcp ${kernel_addr_r} " \
-               "&& run fdt_fixup && bootm ${kernel_addr_r} - ${dtbparam}\0" \
+               "&& run fdt_fixup && bootz ${kernel_addr_r} - ${dtbparam}\0" \
        "nfsdtbload=setenv dtbparam; tftp ${fdt_addr_r} " \
                "${soc}-apalis-${fdt_board}.dtb " \
                "&& setenv dtbparam ${fdt_addr_r}\0"
@@ -81,7 +81,7 @@
                "${vidargs}; echo Booting from SD card in 8bit slot...; " \
                "run sddtbload; load mmc ${sddev}:${sdbootpart} " \
                "${kernel_addr_r} ${boot_file} && run fdt_fixup && " \
-               "bootm ${kernel_addr_r} - ${dtbparam}\0" \
+               "bootz ${kernel_addr_r} - ${dtbparam}\0" \
        "sdbootpart=1\0" \
        "sddev=1\0" \
        "sddtbload=setenv dtbparam; load mmc ${sddev}:${sdbootpart} " \
@@ -98,7 +98,7 @@
                "${usbargs} ${vidargs}; echo Booting from USB stick...; " \
                "run usbdtbload; load usb ${usbdev}:${usbbootpart} " \
                "${kernel_addr_r} ${boot_file} && run fdt_fixup && " \
-               "bootm ${kernel_addr_r} - ${dtbparam}\0" \
+               "bootz ${kernel_addr_r} - ${dtbparam}\0" \
        "usbbootpart=1\0" \
        "usbdev=0\0" \
        "usbdtbload=setenv dtbparam; load usb ${usbdev}:${usbbootpart} " \
@@ -108,7 +108,7 @@
        "usbrootpart=2\0"
 
 #define BOARD_EXTRA_ENV_SETTINGS \
-       "boot_file=uImage\0" \
+       "boot_file=zImage\0" \
        "console=ttyS0\0" \
        "defargs=lp0_vec=2064 at 0xf46ff000 core_edp_mv=1150 core_edp_ma=4000 " \
                "usb_port_owner_info=2 lane_owner_info=6 emc_max_dvfs=0 " \
--

2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

Signature · 4 lines
Best regards

Oleksandr Suvorov
cryosay at gmail.com
#12 lore raw

PATCH 7/9 apalis-tk1/t30: colibri_t30: display reset reason

In reply to Igor Opaniuk

From: Dominik Sliwa <[email protected]>

Display proper reset reason after the SoC info.

---

 arch/arm/mach-tegra/sys_info.c | 32 ++++++++++++++++++++++----------
 1 file changed, 22 insertions(+), 10 deletions(-)
arch/arm/mach-tegra/sys_info.c +22 -10
index 9975f33e0b..5dc998a52b 100644
@@ -6,24 +6,36 @@
 
 #include <common.h>
 #include <linux/ctype.h>
+#if defined(CONFIG_TEGRA124) || defined(CONFIG_TEGRA30)
+#include <asm/arch-tegra/pmc.h>
 
-static void upstring(char *s)
+static char *get_reset_cause(void)
 {
-	while (*s) {
-		*s = toupper(*s);
-		s++;
+	struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+
+	switch (pmc->pmc_reset_status) {
+	case 0x00:
+		return "POR";
+	case 0x01:
+		return "WATCHDOG";
+	case 0x02:
+		return "SENSOR";
+	case 0x03:
+		return "SW_MAIN";
+	case 0x04:
+		return "LP0";
 	}
+	return "UNKNOWN";
 }
+#endif
 
 /* Print CPU information */
 int print_cpuinfo(void)
 {
-	char soc_name[10];
-
-	strncpy(soc_name, CONFIG_SYS_SOC, 10);
-	upstring(soc_name);
-	puts(soc_name);
-	puts("\n");
+	printf("SoC: %s\n", CONFIG_SYS_SOC);
+#if defined(CONFIG_TEGRA124) || defined(CONFIG_TEGRA30)
+	printf("Reset cause: %s\n", get_reset_cause());
+#endif
 
 	/* TBD: Add printf of major/minor rev info, stepping, etc. */
 	return 0;
Signature · 1 line
2.17.1
#13 lore raw

PATCH 8/9 apalis-tk1: remove default vesa vga mode from vidargs

In reply to Igor Opaniuk

From: Marcel Ziswiler <[email protected]>

Remove video=tegrafb0:640x480-16 at 60 aka VESA VGA mode from vidargs in order for the panel specification in the device tree to be used. This causes the default to be the 10.1" LVDS display which will be available in the Toradex webshop shortly.

---

 include/configs/apalis-tk1.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/configs/apalis-tk1.h +1 -1
index 10f2948c62..843e64e3cc 100644
@@ -137,7 +137,7 @@
 		"load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
 		"source ${loadaddr}\0" \
 	USB_BOOTCMD \
-	"vidargs=video=tegrafb0:640x480-16 at 60 fbcon=map:1\0"
+	"vidargs=fbcon=map:1\0"
 
 /* Increase console I/O buffer size */
 #undef CONFIG_SYS_CBSIZE
Signature · 1 line
2.17.1
#14 lore raw

PATCH 8/9 apalis-tk1: remove default vesa vga mode from vidargs

Quoted 10 lines · Igor Opaniuk

From: Marcel Ziswiler <[email protected]>

Remove video=tegrafb0:640x480-16 at 60 aka VESA VGA mode from vidargs in order for the panel specification in the device tree to be used. This causes the default to be the 10.1" LVDS display which will be available in the Toradex webshop shortly.

Quoted 25 lines

---

 include/configs/apalis-tk1.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/configs/apalis-tk1.h +1 -2
index 10f2948c62..843e64e3cc 100644
@@ -137,7 +137,7 @@
                "load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
                "source ${loadaddr}\0" \
        USB_BOOTCMD \
-       "vidargs=video=tegrafb0:640x480-16 at 60 fbcon=map:1\0"
+       "vidargs=fbcon=map:1\0"
 
 /* Increase console I/O buffer size */
 #undef CONFIG_SYS_CBSIZE
--

2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

Signature · 6 lines
Best regards
Oleksandr Suvorov

Toradex AG
Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500
4800 (main line)
#15 lore raw

PATCH 9/9 apalis-tk1: remove non-esential power rails on boot

In reply to Igor Opaniuk

From: Dominik Sliwa <[email protected]>

When mainline kernels reboot TK1 they use SW_RESET, that reset mode does not reset PMIC. Some rails need to be off for RAM Re-repair to work correctly.

---

 arch/arm/mach-tegra/tegra124/cpu.c     | 45 ++++++++++++++++++++++++++
 board/toradex/apalis-tk1/as3722_init.c | 23 +++++++++++++
 2 files changed, 68 insertions(+)
arch/arm/mach-tegra/tegra124/cpu.c +45 -0
index 992c0beb04..abc050c27b 100644
@@ -238,6 +238,45 @@ static bool is_partition_powered(u32 partid)
 	return !!(reg & (1 << partid));
 }
 
+static void unpower_partition(u32 partid)
+{
+	struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+
+	debug("%s: part ID = %08X\n", __func__, partid);
+	/* Is the partition on? */
+	if (is_partition_powered(partid)) {
+		/* Yes, toggle the partition power state (ON -> OFF) */
+		debug("power_partition, toggling state\n");
+		writel(START_CP | partid, &pmc->pmc_pwrgate_toggle);
+
+		/* Wait for the power to come down */
+		while (is_partition_powered(partid))
+			;
+
+		/* Give I/O signals time to stabilize */
+		udelay(IO_STABILIZATION_DELAY);
+	}
+}
+
+void unpower_cpus(void)
+{
+	debug("%s entry: G cluster\n", __func__);
+
+	/* Power down the fast cluster rail partition */
+	debug("%s: CRAIL\n", __func__);
+	unpower_partition(CRAIL);
+
+	/* Power down the fast cluster non-CPU partition */
+	debug("%s: C0NC\n", __func__);
+	unpower_partition(C0NC);
+
+	/* Power down the fast cluster CPU0 partition */
+	debug("%s: CE0\n", __func__);
+	unpower_partition(CE0);
+
+	debug("%s: done\n", __func__);
+}
+
 static void power_partition(u32 partid)
 {
 	struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
@@ -284,6 +323,12 @@ void start_cpu(u32 reset_vector)
 
 	debug("%s entry, reset_vector = %x\n", __func__, reset_vector);
 
+	/*
+	 * High power clusters are on after software reset,
+	 * it may interfere with tegra124_ram_repair.
+	 * unpower them.
+	 */
+	unpower_cpus();
 	tegra124_init_clocks();
 
 	/* Set power-gating timer multiplier */
board/toradex/apalis-tk1/as3722_init.c +23 -0
index bd754e5fcf..15f8dce2f1 100644
@@ -43,6 +43,29 @@ void pmic_enable_cpu_vdd(void)
 	udelay(10 * 1000);
 #endif
 
+	/*
+	 * Make sure all non-fused regulators are down.
+	 * That way we're in known state after software reboot from linux
+	 */
+	tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+	tegra_i2c_ll_write_data(0x0003, I2C_SEND_2_BYTES);
+	udelay(10 * 1000);
+	tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+	tegra_i2c_ll_write_data(0x0004, I2C_SEND_2_BYTES);
+	udelay(10 * 1000);
+	tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+	tegra_i2c_ll_write_data(0x001b, I2C_SEND_2_BYTES);
+	udelay(10 * 1000);
+	tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+	tegra_i2c_ll_write_data(0x0014, I2C_SEND_2_BYTES);
+	udelay(10 * 1000);
+	tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+	tegra_i2c_ll_write_data(0x001a, I2C_SEND_2_BYTES);
+	udelay(10 * 1000);
+	tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+	tegra_i2c_ll_write_data(0x0019, I2C_SEND_2_BYTES);
+	udelay(10 * 1000);
+
 	debug("%s: Setting VDD_CPU to 1.0V via AS3722 reg 0/4D\n", __func__);
 	/*
 	 * Bring up VDD_CPU via the AS3722 PMIC on the PWR I2C bus.
Signature · 1 line
2.17.1
#16 lore raw

PATCH 9/9 apalis-tk1: remove non-esential power rails on boot

Quoted 9 lines · Igor Opaniuk

From: Dominik Sliwa <[email protected]>

When mainline kernels reboot TK1 they use SW_RESET, that reset mode does not reset PMIC. Some rails need to be off for RAM Re-repair to work correctly.

Quoted 110 lines

---

 arch/arm/mach-tegra/tegra124/cpu.c     | 45 ++++++++++++++++++++++++++
 board/toradex/apalis-tk1/as3722_init.c | 23 +++++++++++++
 2 files changed, 68 insertions(+)
arch/arm/mach-tegra/tegra124/cpu.c +45 -0
index 992c0beb04..abc050c27b 100644
@@ -238,6 +238,45 @@ static bool is_partition_powered(u32 partid)
        return !!(reg & (1 << partid));
 }
 
+static void unpower_partition(u32 partid)
+{
+       struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+
+       debug("%s: part ID = %08X\n", __func__, partid);
+       /* Is the partition on? */
+       if (is_partition_powered(partid)) {
+               /* Yes, toggle the partition power state (ON -> OFF) */
+               debug("power_partition, toggling state\n");
+               writel(START_CP | partid, &pmc->pmc_pwrgate_toggle);
+
+               /* Wait for the power to come down */
+               while (is_partition_powered(partid))
+                       ;
+
+               /* Give I/O signals time to stabilize */
+               udelay(IO_STABILIZATION_DELAY);
+       }
+}
+
+void unpower_cpus(void)
+{
+       debug("%s entry: G cluster\n", __func__);
+
+       /* Power down the fast cluster rail partition */
+       debug("%s: CRAIL\n", __func__);
+       unpower_partition(CRAIL);
+
+       /* Power down the fast cluster non-CPU partition */
+       debug("%s: C0NC\n", __func__);
+       unpower_partition(C0NC);
+
+       /* Power down the fast cluster CPU0 partition */
+       debug("%s: CE0\n", __func__);
+       unpower_partition(CE0);
+
+       debug("%s: done\n", __func__);
+}
+
 static void power_partition(u32 partid)
 {
        struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
@@ -284,6 +323,12 @@ void start_cpu(u32 reset_vector)
 
        debug("%s entry, reset_vector = %x\n", __func__, reset_vector);
 
+       /*
+        * High power clusters are on after software reset,
+        * it may interfere with tegra124_ram_repair.
+        * unpower them.
+        */
+       unpower_cpus();
        tegra124_init_clocks();
 
        /* Set power-gating timer multiplier */
board/toradex/apalis-tk1/as3722_init.c +23 -1
index bd754e5fcf..15f8dce2f1 100644
@@ -43,6 +43,29 @@ void pmic_enable_cpu_vdd(void)
        udelay(10 * 1000);
 #endif
 
+       /*
+        * Make sure all non-fused regulators are down.
+        * That way we're in known state after software reboot from linux
+        */
+       tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(0x0003, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+       tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(0x0004, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+       tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(0x001b, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+       tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(0x0014, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+       tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(0x001a, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+       tegra_i2c_ll_write_addr(AS3722_I2C_ADDR, 2);
+       tegra_i2c_ll_write_data(0x0019, I2C_SEND_2_BYTES);
+       udelay(10 * 1000);
+
        debug("%s: Setting VDD_CPU to 1.0V via AS3722 reg 0/4D\n", __func__);
        /*
         * Bring up VDD_CPU via the AS3722 PMIC on the PWR I2C bus.
--

2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

Signature · 4 lines
Best regards

Oleksandr Suvorov
cryosay at gmail.com
#17 lore raw

cover apalis-tk1: fixes/updates for v2019.10

In reply to Igor Opaniuk

The 'switch to zImage' patch fails to apply using git am, either in the complete (9-patch) bundle, or as part of the 5-patch Igor Opaniuk bundle, or even as a stand-alone patch. This is using the current TOT u-boot-tegra/master.

Please ensure the entire bundle of Apalis-TK1 patches can be applied to u-boot-tegra/master.

Thanks,

Tom

--
nvpublic

-----Original Message-----
From: Igor Opaniuk <[email protected]>
Sent: Wednesday, July 31, 2019 5:05 AM
To: u-boot at lists.denx.de
Cc: Marcel Ziswiler <[email protected]>; Philippe Schenker <[email protected]>; Oleksandr Suvorov <[email protected]>; Dominik Sliwa <[email protected]>; Igor Opaniuk <[email protected]>; Albert Aribaud <[email protected]>; Igor Opaniuk <[email protected]>; Tom Warren <[email protected]>
Subject: [PATCH v1 0/9] apalis-tk1: fixes/updates for v2019.10

Misc. fixes related to pinmux configuration (fan), default bootargs, reset reason output and power rail configuration.

Dominik Sliwa (2):
apalis-tk1/t30: colibri_t30: display reset reason
apalis-tk1: remove non-esential power rails on boot

Igor Opaniuk (5):
apalis-tk1: set apalis gpio 8 aka fan_en
apalis-tk1: provide proper USB vendor id
apalis-tk1: enable user debug by default
apalis-tk1: add pcie_aspm=off to defargs
apalis-tk1: switch to zImage

Marcel Ziswiler (2):
apalis-tk1: do not explicitly release reset_moci#
apalis-tk1: remove default vesa vga mode from vidargs

 arch/arm/mach-tegra/sys_info.c                | 32 ++++++++-----
 arch/arm/mach-tegra/tegra124/cpu.c            | 45 +++++++++++++++++++
 board/toradex/apalis-tk1/apalis-tk1.c         | 10 +++++
 board/toradex/apalis-tk1/as3722_init.c        | 23 ++++++++++
 .../apalis-tk1/pinmux-config-apalis-tk1.h     |  2 +-
 configs/apalis-tk1_defconfig                  |  2 +-
 include/configs/apalis-tk1.h                  | 17 +++----
 7 files changed, 111 insertions(+), 20 deletions(-)

--
2.17.1

#18 lore raw

cover apalis-tk1: fixes/updates for v2019.10

Hi Tom,

Quoted 45 lines · Tom Warren

The 'switch to zImage' patch fails to apply using git am, either in the complete (9-patch) bundle, or as part of the 5-patch Igor Opaniuk bundle, or even as a stand-alone patch. This is using the current TOT u-boot-tegra/master.

Please ensure the entire bundle of Apalis-TK1 patches can be applied to u-boot-tegra/master.

Thanks,

Tom

--
nvpublic

-----Original Message-----
From: Igor Opaniuk <[email protected]>
Sent: Wednesday, July 31, 2019 5:05 AM
To: u-boot at lists.denx.de
Cc: Marcel Ziswiler <[email protected]>; Philippe Schenker <[email protected]>; Oleksandr Suvorov <[email protected]>; Dominik Sliwa <[email protected]>; Igor Opaniuk <[email protected]>; Albert Aribaud <[email protected]>; Igor Opaniuk <[email protected]>; Tom Warren <[email protected]>
Subject: [PATCH v1 0/9] apalis-tk1: fixes/updates for v2019.10

Misc. fixes related to pinmux configuration (fan), default bootargs, reset reason output and power rail configuration.

Dominik Sliwa (2):
apalis-tk1/t30: colibri_t30: display reset reason
apalis-tk1: remove non-esential power rails on boot

Igor Opaniuk (5):
apalis-tk1: set apalis gpio 8 aka fan_en
apalis-tk1: provide proper USB vendor id
apalis-tk1: enable user debug by default
apalis-tk1: add pcie_aspm=off to defargs
apalis-tk1: switch to zImage

Marcel Ziswiler (2):
apalis-tk1: do not explicitly release reset_moci#
apalis-tk1: remove default vesa vga mode from vidargs

 arch/arm/mach-tegra/sys_info.c                | 32 ++++++++-----
 arch/arm/mach-tegra/tegra124/cpu.c            | 45 +++++++++++++++++++
 board/toradex/apalis-tk1/apalis-tk1.c         | 10 +++++
 board/toradex/apalis-tk1/as3722_init.c        | 23 ++++++++++
 .../apalis-tk1/pinmux-config-apalis-tk1.h     |  2 +-
 configs/apalis-tk1_defconfig                  |  2 +-
 include/configs/apalis-tk1.h                  | 17 +++----
 7 files changed, 111 insertions(+), 20 deletions(-)
Quoted 3 lines

--
2.17.1

Will do,
Thanks!

Signature · 8 lines
Best regards - Freundliche Grüsse - Meilleures salutations

Igor Opaniuk

mailto: igor.opaniuk at gmail.com
skype: igor.opanyuk
+380 (93) 836 40 67
http://ua.linkedin.com/in/iopaniuk