Skip to contentSkip to conversation

Add bluetooth support for Orange Pi 3

PATCH RESEND Applied [email protected] 2 participants 4 messages Oct 7, 2019 – Oct 8, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover Add bluetooth support for Orange Pi 3

From: Ondrej Jirman <[email protected]>

(Re-send for Maxime, with already applied patches dropped. Nothing new.)

This series implements bluetooth support for Xunlong Orange Pi 3 board.

The board uses AP6256 WiFi/BT 5.0 chip.

Summary of changes:

- add more delay to let initialize the chip
- let the kernel detect firmware file path
- add new compatible and update dt-bindings
- update Orange Pi 3 / H6 DTS

Please take a look.

thank you and regards,
Ondrej Jirman

Ondrej Jirman (2):
arm64: dts: allwinner: h6: Add pin configs for uart1
arm64: dts: allwinner: orange-pi-3: Enable UART1 / Bluetooth

 .../dts/allwinner/sun50i-h6-orangepi-3.dts    | 19 +++++++++++++++++++
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi  | 10 ++++++++++
Signature · 1 line
2.23.0
#1 lore raw

PATCH RESEND 1/2 arm64: dts: allwinner: h6: Add pin configs for uart1

From: Ondrej Jirman <[email protected]>

Orange Pi 3 uses UART1 for bluetooth. Add pinconfigs so that we can use them.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +10 -0
index 67f920e0fc33..7657e816096b 100644
@@ -298,6 +298,16 @@
 				pins = "PH0", "PH1";
 				function = "uart0";
 			};
+
+			uart1_pins: uart1-pins {
+				pins = "PG6", "PG7";
+				function = "uart1";
+			};
+
+			uart1_rts_cts_pins: uart1-rts-cts-pins {
+				pins = "PG8", "PG9";
+				function = "uart1";
+			};
 		};
 
 		gic: interrupt-controller@3021000 {
Signature · 1 line
2.23.0
#2 lore raw

PATCH RESEND 2/2 arm64: dts: allwinner: orange-pi-3: Enable UART1 / Bluetooth

In reply to [email protected]

From: Ondrej Jirman <[email protected]>

The board contains AP6256 WiFi/BT module that has its bluetooth part connected to SoC's UART1 port. Enable this port, and add node for the bluetooth device.

Bluetooth part is named bcm4345c5.

You'll need a BCM4345C5.hcd firmware file that can be found in the Xulongs's repository for H6:

https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256

The driver expects the firmware at the following path relative to the firmware directory:

brcm/BCM4345C5.hcd

---
 .../dts/allwinner/sun50i-h6-orangepi-3.dts    | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts +19 -0
index 49d954369087..a9e776446c35 100644
@@ -15,6 +15,7 @@
 
 	aliases {
 		serial0 = &uart0;
+		serial1 = &uart1;
 	};
 
 	chosen {
@@ -271,6 +272,24 @@
 	status = "okay";
 };
 
+/* There's the BT part of the AP6256 connected to that UART */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4345c5";
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
+		host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */
+		shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
+		max-speed = <1500000>;
+	};
+};
+
 &usb2otg {
 	/*
 	 * This board doesn't have a controllable VBUS even though it
Signature · 1 line
2.23.0
#3 lore raw
In reply to [email protected]
Quoted 8 lines · On Mon, Oct 07, 2019 at 10:31:50PM +0200, [email protected] wrote:

From: Ondrej Jirman <[email protected]>

(Re-send for Maxime, with already applied patches dropped. Nothing new.)

This series implements bluetooth support for Xunlong Orange Pi 3 board.

The board uses AP6256 WiFi/BT 5.0 chip.

Quoted 8 lines

Summary of changes:

- add more delay to let initialize the chip
- let the kernel detect firmware file path
- add new compatible and update dt-bindings
- update Orange Pi 3 / H6 DTS

Please take a look.

Applied both, thanks!
Maxime