Skip to contentSkip to conversation

arm64: ti: k3-j721e: Add SERDES PHY and USB3.0 support

PATCH Superseded Roger Quadros 3 participants 11 messages Mar 3, 2020 – Apr 24, 2020

Subsystems (4)

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v2 cover arm64: ti: k3-j721e: Add SERDES PHY and USB3.0 support

Hi Tero,

This series adds SERDES PHY support. The relevant PHY driver and bindings are already in v5.6.

It also adds Super-Speed support to the Type-C port on the EVM. The USB Type-C related driver support is in v5.6.

Please queue this for v5.7 if no objections. Thanks.

cheers,
-roger

Changelog:
v2:
- Addressed Rob's comments.
- Changed type-C debounce delay from 300ms to 700ms as 300ms is not sufficient on EVM.

Kishon Vijay Abraham I (3):
dt-bindings: syscon: Add TI's J721E specific compatible string
arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes
arm64: dts: ti: k3-j721e-main: Add serdes_ln_ctrl node to select
SERDES lane mux

Roger Quadros (3):
arm64: dts: ti: k3-j721e-main.dtsi: Add USB to SERDES MUX
arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0
arm64: dts: k3-j721e-proc-board: Add wait time for sampling Type-C DIR
line

 .../devicetree/bindings/mfd/syscon.yaml       |   1 +
 .../dts/ti/k3-j721e-common-proc-board.dts     |  33 ++-
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi     | 275 ++++++++++++++++++
 include/dt-bindings/mux/mux-j721e-wiz.h       |  53 ++++
 4 files changed, 360 insertions(+), 2 deletions(-)
 create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
#1 lore raw

PATCH v2 1/6 dt-bindings: syscon: Add TI's J721E specific compatible string

From: Kishon Vijay Abraham I <[email protected]>

Add TI's J721E SoC specific compatible string.

---
 Documentation/devicetree/bindings/mfd/syscon.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/mfd/syscon.yaml +1 -0
index 39375e4313d2..f9aac75d423a 100644
@@ -38,6 +38,7 @@ properties:
           - allwinner,sun8i-h3-system-controller
           - allwinner,sun8i-v3s-system-controller
           - allwinner,sun50i-a64-system-controller
+          - ti,j721e-system-controller
 
         - const: syscon
 
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
#2 lore raw

PATCH v2 2/6 arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes

In reply to Roger Quadros

From: Kishon Vijay Abraham I <[email protected]>

Add DT nodes for all instances of WIZ and SERDES modules.

---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 241 ++++++++++++++++++++++
 1 file changed, 241 insertions(+)
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +241 -0
index 0b9d14b838a1..cbaadee5bfdc 100644
@@ -4,6 +4,7 @@
  *
  * Copyright (C) 2016-2019 Texas Instruments Incorporated - http://www.ti.com/
  */
+#include <dt-bindings/phy/phy.h>
 
 &cbass_main {
 	msmc_ram: sram@70000000 {
@@ -265,6 +266,246 @@
 		pinctrl-single,function-mask = <0xffffffff>;
 	};
 
+	dummy_cmn_refclk: dummy-cmn-refclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <100000000>;
+	};
+
+	dummy_cmn_refclk1: dummy-cmn-refclk1 {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <100000000>;
+	};
+
+	serdes_wiz0: wiz@5000000 {
+		compatible = "ti,j721e-wiz-16g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 292 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 292 5>, <&k3_clks 292 11>, <&dummy_cmn_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		assigned-clocks = <&k3_clks 292 11>, <&k3_clks 292 0>;
+		assigned-clock-parents = <&k3_clks 292 15>, <&k3_clks 292 4>;
+		num-lanes = <2>;
+		#reset-cells = <1>;
+		ranges = <0x5000000 0x0 0x5000000 0x10000>;
+
+		wiz0_pll0_refclk: pll0-refclk {
+			clocks = <&k3_clks 292 11>, <&dummy_cmn_refclk>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_pll0_refclk>;
+			assigned-clock-parents = <&k3_clks 292 11>;
+		};
+
+		wiz0_pll1_refclk: pll1-refclk {
+			clocks = <&k3_clks 292 0>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_pll1_refclk>;
+			assigned-clock-parents = <&k3_clks 292 0>;
+		};
+
+		wiz0_refclk_dig: refclk-dig {
+			clocks = <&k3_clks 292 11>, <&k3_clks 292 0>, <&dummy_cmn_refclk>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_refclk_dig>;
+			assigned-clock-parents = <&k3_clks 292 11>;
+		};
+
+		wiz0_cmn_refclk_dig_div: cmn-refclk-dig-div {
+			clocks = <&wiz0_refclk_dig>;
+			#clock-cells = <0>;
+		};
+
+		wiz0_cmn_refclk1_dig_div: cmn-refclk1-dig-div {
+			clocks = <&wiz0_pll1_refclk>;
+			#clock-cells = <0>;
+		};
+
+		serdes0: serdes@5000000 {
+			compatible = "ti,sierra-phy-t0";
+			reg-names = "serdes";
+			reg = <0x5000000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&serdes_wiz0 0>;
+			reset-names = "sierra_reset";
+			clocks = <&wiz0_cmn_refclk_dig_div>, <&wiz0_cmn_refclk1_dig_div>;
+			clock-names = "cmn_refclk_dig_div", "cmn_refclk1_dig_div";
+		};
+	};
+
+	serdes_wiz1: wiz@5010000 {
+		compatible = "ti,j721e-wiz-16g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 293 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 293 5>, <&k3_clks 293 13>, <&dummy_cmn_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		assigned-clocks = <&k3_clks 293 13>, <&k3_clks 293 0>;
+		assigned-clock-parents = <&k3_clks 293 17>, <&k3_clks 293 4>;
+		num-lanes = <2>;
+		#reset-cells = <1>;
+		ranges = <0x5010000 0x0 0x5010000 0x10000>;
+
+		wiz1_pll0_refclk: pll0-refclk {
+			clocks = <&k3_clks 293 13>, <&dummy_cmn_refclk>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz1_pll0_refclk>;
+			assigned-clock-parents = <&k3_clks 293 13>;
+		};
+
+		wiz1_pll1_refclk: pll1-refclk {
+			clocks = <&k3_clks 293 0>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz1_pll1_refclk>;
+			assigned-clock-parents = <&k3_clks 293 0>;
+		};
+
+		wiz1_refclk_dig: refclk-dig {
+			clocks = <&k3_clks 293 13>, <&k3_clks 293 0>, <&dummy_cmn_refclk>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz1_refclk_dig>;
+			assigned-clock-parents = <&k3_clks 293 13>;
+		};
+
+		wiz1_cmn_refclk_dig_div: cmn-refclk-dig-div{
+			clocks = <&wiz1_refclk_dig>;
+			#clock-cells = <0>;
+		};
+
+		wiz1_cmn_refclk1_dig_div: cmn-refclk1-dig-div {
+			clocks = <&wiz1_pll1_refclk>;
+			#clock-cells = <0>;
+		};
+
+		serdes1: serdes@5010000 {
+			compatible = "ti,sierra-phy-t0";
+			reg-names = "serdes";
+			reg = <0x5010000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&serdes_wiz1 0>;
+			reset-names = "sierra_reset";
+			clocks = <&wiz1_cmn_refclk_dig_div>, <&wiz1_cmn_refclk1_dig_div>;
+			clock-names = "cmn_refclk_dig_div", "cmn_refclk1_dig_div";
+		};
+	};
+
+	serdes_wiz2: wiz@5020000 {
+		compatible = "ti,j721e-wiz-16g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 294 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 294 5>, <&k3_clks 294 11>, <&dummy_cmn_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		assigned-clocks = <&k3_clks 294 11>, <&k3_clks 294 0>;
+		assigned-clock-parents = <&k3_clks 294 15>, <&k3_clks 294 4>;
+		num-lanes = <2>;
+		#reset-cells = <1>;
+		ranges = <0x5020000 0x0 0x5020000 0x10000>;
+
+		wiz2_pll0_refclk: pll0-refclk {
+			clocks = <&k3_clks 294 11>, <&dummy_cmn_refclk>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz2_pll0_refclk>;
+			assigned-clock-parents = <&k3_clks 294 11>;
+		};
+
+		wiz2_pll1_refclk: pll1-refclk {
+			clocks = <&k3_clks 294 0>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz2_pll1_refclk>;
+			assigned-clock-parents = <&k3_clks 294 0>;
+		};
+
+		wiz2_refclk_dig: refclk-dig {
+			clocks = <&k3_clks 294 11>, <&k3_clks 294 0>, <&dummy_cmn_refclk>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz2_refclk_dig>;
+			assigned-clock-parents = <&k3_clks 294 11>;
+		};
+
+		wiz2_cmn_refclk_dig_div: cmn-refclk-dig-div {
+			clocks = <&wiz2_refclk_dig>;
+			#clock-cells = <0>;
+		};
+
+		wiz2_cmn_refclk1_dig_div: cmn-refclk1-dig-div {
+			clocks = <&wiz2_pll1_refclk>;
+			#clock-cells = <0>;
+		};
+
+		serdes2: serdes@5020000 {
+			compatible = "ti,sierra-phy-t0";
+			reg-names = "serdes";
+			reg = <0x5020000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&serdes_wiz2 0>;
+			reset-names = "sierra_reset";
+			clocks = <&wiz2_cmn_refclk_dig_div>, <&wiz2_cmn_refclk1_dig_div>;
+			clock-names = "cmn_refclk_dig_div", "cmn_refclk1_dig_div";
+		};
+	};
+
+	serdes_wiz3: wiz@5030000 {
+		compatible = "ti,j721e-wiz-16g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 295 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 295 5>, <&k3_clks 295 9>, <&dummy_cmn_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		assigned-clocks = <&k3_clks 295 9>, <&k3_clks 295 0>;
+		assigned-clock-parents = <&k3_clks 295 13>, <&k3_clks 295 4>;
+		num-lanes = <2>;
+		#reset-cells = <1>;
+		ranges = <0x5030000 0x0 0x5030000 0x10000>;
+
+		wiz3_pll0_refclk: pll0-refclk {
+			clocks = <&k3_clks 295 9>, <&dummy_cmn_refclk>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz3_pll0_refclk>;
+			assigned-clock-parents = <&k3_clks 295 9>;
+		};
+
+		wiz3_pll1_refclk: pll1-refclk {
+			clocks = <&k3_clks 295 0>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz3_pll1_refclk>;
+			assigned-clock-parents = <&k3_clks 295 0>;
+		};
+
+		wiz3_refclk_dig: refclk-dig {
+			clocks = <&k3_clks 295 9>, <&k3_clks 295 0>, <&dummy_cmn_refclk>, <&dummy_cmn_refclk1>;
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz3_refclk_dig>;
+			assigned-clock-parents = <&k3_clks 295 9>;
+		};
+
+		wiz3_cmn_refclk_dig_div: cmn-refclk-dig-div {
+			clocks = <&wiz3_refclk_dig>;
+			#clock-cells = <0>;
+		};
+
+		wiz3_cmn_refclk1_dig_div: cmn-refclk1-dig-div {
+			clocks = <&wiz3_pll1_refclk>;
+			#clock-cells = <0>;
+		};
+
+		serdes3: serdes@5030000 {
+			compatible = "ti,sierra-phy-t0";
+			reg-names = "serdes";
+			reg = <0x5030000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&serdes_wiz3 0>;
+			reset-names = "sierra_reset";
+			clocks = <&wiz3_cmn_refclk_dig_div>, <&wiz3_cmn_refclk1_dig_div>;
+			clock-names = "cmn_refclk_dig_div", "cmn_refclk1_dig_div";
+		};
+	};
+
 	main_uart0: serial@2800000 {
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02800000 0x00 0x100>;
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
#3 lore raw

PATCH v2 3/6 arm64: dts: ti: k3-j721e-main: Add serdes_ln_ctrl node to select SERDES lane mux

In reply to Roger Quadros

From: Kishon Vijay Abraham I <[email protected]>

Add serdes_ln_ctrl node used for selecting SERDES lane mux.

---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 27 ++++++++++++
 include/dt-bindings/mux/mux-j721e-wiz.h   | 53 +++++++++++++++++++++++
 2 files changed, 80 insertions(+)
 create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +27 -0
index cbaadee5bfdc..c5d54af37e91 100644
@@ -5,6 +5,8 @@
  * Copyright (C) 2016-2019 Texas Instruments Incorporated - http://www.ti.com/
  */
 #include <dt-bindings/phy/phy.h>
+#include <dt-bindings/mux/mux.h>
+#include <dt-bindings/mux/mux-j721e-wiz.h>
 
 &cbass_main {
 	msmc_ram: sram@70000000 {
@@ -19,6 +21,31 @@
 		};
 	};
 
+	scm_conf: scm-conf@100000 {
+		compatible = "syscon", "simple-mfd", "ti,j721e-system-controller";
+		reg = <0 0x00100000 0 0x1c000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x00100000 0x1c000>;
+
+		serdes_ln_ctrl: serdes-ln-ctrl@4080 {
+			compatible = "mmio-mux";
+			reg = <0x00004080 0x50>;
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
+					<0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
+					<0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
+					<0x40b0 0x3>, <0x40b4 0x3>, /* SERDES3 lane0/1 select */
+					<0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>;
+					/* SERDES4 lane0/1/2/3 select */
+			idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
+				      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
+				      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
+				      <MUX_IDLE_AS_IS>, <SERDES3_LANE1_USB3_0>,
+				      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
+		};
+	};
+
 	gic500: interrupt-controller@1800000 {
 		compatible = "arm,gic-v3";
 		#address-cells = <2>;
include/dt-bindings/mux/mux-j721e-wiz.h new file +53 -0

53 lines not on this page · raw message

Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
maintainer
#4 lore raw

Re: [PATCH v2 3/6] arm64: dts: ti: k3-j721e-main: Add serdes_ln_ctrl node to select SERDES lane mux

Quoted 27 lines · Roger Quadros

From: Kishon Vijay Abraham I <[email protected]>

Add serdes_ln_ctrl node used for selecting SERDES lane mux.

---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 27 ++++++++++++
 include/dt-bindings/mux/mux-j721e-wiz.h   | 53 +++++++++++++++++++++++
 2 files changed, 80 insertions(+)
 create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +2 -0
index cbaadee5bfdc..c5d54af37e91 100644
@@ -5,6 +5,8 @@
  * Copyright (C) 2016-2019 Texas Instruments Incorporated - http://www.ti.com/
  */
 #include <dt-bindings/phy/phy.h>
+#include <dt-bindings/mux/mux.h>
+#include <dt-bindings/mux/mux-j721e-wiz.h>
 
 &cbass_main {
 	msmc_ram: sram@70000000 {

arch/arm64/boot/dts/ti/k3-j721e-main.dtsi line 25

Quoted 5 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +2 -0
@@ -19,6 +21,31 @@
 		};
 	};
 
+	scm_conf: scm-conf@100000 {
+		compatible = "syscon", "simple-mfd", "ti,j721e-system-controller";

Wrong ordering. Most significant first.

arch/arm64/boot/dts/ti/k3-j721e-main.dtsi line 31

Quoted 6 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +6 -0
+		reg = <0 0x00100000 0 0x1c000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x00100000 0x1c000>;
+
+		serdes_ln_ctrl: serdes-ln-ctrl@4080 {

Your syscon.yaml change is not valid if you have child nodes. Do a specific binding for this block.

Quoted 83 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +17 -0
+			compatible = "mmio-mux";
+			reg = <0x00004080 0x50>;
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
+					<0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
+					<0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
+					<0x40b0 0x3>, <0x40b4 0x3>, /* SERDES3 lane0/1 select */
+					<0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>;
+					/* SERDES4 lane0/1/2/3 select */
+			idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
+				      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
+				      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
+				      <MUX_IDLE_AS_IS>, <SERDES3_LANE1_USB3_0>,
+				      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
+		};
+	};
+
 	gic500: interrupt-controller@1800000 {
 		compatible = "arm,gic-v3";
 		#address-cells = <2>;
include/dt-bindings/mux/mux-j721e-wiz.h new file +53 -0
new file mode 100644
index 000000000000..fd1c4ea9fc7f
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides constants for J721E WIZ.
+ */
+
+#ifndef _DT_BINDINGS_J721E_WIZ
+#define _DT_BINDINGS_J721E_WIZ
+
+#define SERDES0_LANE0_QSGMII_LANE1	0x0
+#define SERDES0_LANE0_PCIE0_LANE0	0x1
+#define SERDES0_LANE0_USB3_0_SWAP	0x2
+
+#define SERDES0_LANE1_QSGMII_LANE2	0x0
+#define SERDES0_LANE1_PCIE0_LANE1	0x1
+#define SERDES0_LANE1_USB3_0		0x2
+
+#define SERDES1_LANE0_QSGMII_LANE3	0x0
+#define SERDES1_LANE0_PCIE1_LANE0	0x1
+#define SERDES1_LANE0_USB3_1_SWAP	0x2
+#define SERDES1_LANE0_SGMII_LANE0	0x3
+
+#define SERDES1_LANE1_QSGMII_LANE4	0x0
+#define SERDES1_LANE1_PCIE1_LANE1	0x1
+#define SERDES1_LANE1_USB3_1		0x2
+#define SERDES1_LANE1_SGMII_LANE1	0x3
+
+#define SERDES2_LANE0_PCIE2_LANE0	0x1
+#define SERDES2_LANE0_SGMII_LANE0	0x3
+#define SERDES2_LANE0_USB3_1_SWAP	0x2
+
+#define SERDES2_LANE1_PCIE2_LANE1	0x1
+#define SERDES2_LANE1_USB3_1		0x2
+#define SERDES2_LANE1_SGMII_LANE1	0x3
+
+#define SERDES3_LANE0_PCIE3_LANE0	0x1
+#define SERDES3_LANE0_USB3_0_SWAP	0x2
+
+#define SERDES3_LANE1_PCIE3_LANE1	0x1
+#define SERDES3_LANE1_USB3_0		0x2
+
+#define SERDES4_LANE0_EDP_LANE0		0x0
+#define SERDES4_LANE0_QSGMII_LANE5	0x2
+
+#define SERDES4_LANE1_EDP_LANE1		0x0
+#define SERDES4_LANE1_QSGMII_LANE6	0x2
+
+#define SERDES4_LANE2_EDP_LANE2		0x0
+#define SERDES4_LANE2_QSGMII_LANE7	0x2
+
+#define SERDES4_LANE3_EDP_LANE3		0x0
+#define SERDES4_LANE3_QSGMII_LANE8	0x2
+
+#endif /* _DT_BINDINGS_J721E_WIZ */
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
#5 lore raw

Re: [PATCH v2 3/6] arm64: dts: ti: k3-j721e-main: Add serdes_ln_ctrl node to select SERDES lane mux

Hi Rob,

Quoted 36 lines · Rob Herring
Quoted 27 lines · Roger Quadros

From: Kishon Vijay Abraham I <[email protected]>

Add serdes_ln_ctrl node used for selecting SERDES lane mux.

---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 27 ++++++++++++
 include/dt-bindings/mux/mux-j721e-wiz.h   | 53 +++++++++++++++++++++++
 2 files changed, 80 insertions(+)
 create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +2 -0
index cbaadee5bfdc..c5d54af37e91 100644
@@ -5,6 +5,8 @@
  * Copyright (C) 2016-2019 Texas Instruments Incorporated - http://www.ti.com/
  */
 #include <dt-bindings/phy/phy.h>
+#include <dt-bindings/mux/mux.h>
+#include <dt-bindings/mux/mux-j721e-wiz.h>
 
 &cbass_main {
 	msmc_ram: sram@70000000 {

arch/arm64/boot/dts/ti/k3-j721e-main.dtsi line 25

Quoted 5 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +2 -0
@@ -19,6 +21,31 @@
 		};
 	};
 
+	scm_conf: scm-conf@100000 {
+		compatible = "syscon", "simple-mfd", "ti,j721e-system-controller";

Wrong ordering. Most significant first.

Quoted 9 lines

arch/arm64/boot/dts/ti/k3-j721e-main.dtsi line 31

Quoted 6 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +6 -0
+		reg = <0 0x00100000 0 0x1c000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x00100000 0x1c000>;
+
+		serdes_ln_ctrl: serdes-ln-ctrl@4080 {

Your syscon.yaml change is not valid if you have child nodes. Do a specific binding for this block.

Do you mean in addition to having platform specific binding for scm-conf, I need to have platform specific binding for serdes-ln-ctrl.

Since the driver doesn't do any platform specific stuff, the driver doesn't have to change. Is that correct?

Thanks
Kishon

Quoted 84 lines
Quoted 84 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +17 -0
+			compatible = "mmio-mux";
+			reg = <0x00004080 0x50>;
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
+					<0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
+					<0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
+					<0x40b0 0x3>, <0x40b4 0x3>, /* SERDES3 lane0/1 select */
+					<0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>;
+					/* SERDES4 lane0/1/2/3 select */
+			idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
+				      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
+				      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
+				      <MUX_IDLE_AS_IS>, <SERDES3_LANE1_USB3_0>,
+				      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
+		};
+	};
+
 	gic500: interrupt-controller@1800000 {
 		compatible = "arm,gic-v3";
 		#address-cells = <2>;
include/dt-bindings/mux/mux-j721e-wiz.h new file +53 -0
new file mode 100644
index 000000000000..fd1c4ea9fc7f
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides constants for J721E WIZ.
+ */
+
+#ifndef _DT_BINDINGS_J721E_WIZ
+#define _DT_BINDINGS_J721E_WIZ
+
+#define SERDES0_LANE0_QSGMII_LANE1	0x0
+#define SERDES0_LANE0_PCIE0_LANE0	0x1
+#define SERDES0_LANE0_USB3_0_SWAP	0x2
+
+#define SERDES0_LANE1_QSGMII_LANE2	0x0
+#define SERDES0_LANE1_PCIE0_LANE1	0x1
+#define SERDES0_LANE1_USB3_0		0x2
+
+#define SERDES1_LANE0_QSGMII_LANE3	0x0
+#define SERDES1_LANE0_PCIE1_LANE0	0x1
+#define SERDES1_LANE0_USB3_1_SWAP	0x2
+#define SERDES1_LANE0_SGMII_LANE0	0x3
+
+#define SERDES1_LANE1_QSGMII_LANE4	0x0
+#define SERDES1_LANE1_PCIE1_LANE1	0x1
+#define SERDES1_LANE1_USB3_1		0x2
+#define SERDES1_LANE1_SGMII_LANE1	0x3
+
+#define SERDES2_LANE0_PCIE2_LANE0	0x1
+#define SERDES2_LANE0_SGMII_LANE0	0x3
+#define SERDES2_LANE0_USB3_1_SWAP	0x2
+
+#define SERDES2_LANE1_PCIE2_LANE1	0x1
+#define SERDES2_LANE1_USB3_1		0x2
+#define SERDES2_LANE1_SGMII_LANE1	0x3
+
+#define SERDES3_LANE0_PCIE3_LANE0	0x1
+#define SERDES3_LANE0_USB3_0_SWAP	0x2
+
+#define SERDES3_LANE1_PCIE3_LANE1	0x1
+#define SERDES3_LANE1_USB3_0		0x2
+
+#define SERDES4_LANE0_EDP_LANE0		0x0
+#define SERDES4_LANE0_QSGMII_LANE5	0x2
+
+#define SERDES4_LANE1_EDP_LANE1		0x0
+#define SERDES4_LANE1_QSGMII_LANE6	0x2
+
+#define SERDES4_LANE2_EDP_LANE2		0x0
+#define SERDES4_LANE2_QSGMII_LANE7	0x2
+
+#define SERDES4_LANE3_EDP_LANE3		0x0
+#define SERDES4_LANE3_QSGMII_LANE8	0x2
+
+#endif /* _DT_BINDINGS_J721E_WIZ */
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
#6 lore raw

Re: [PATCH v2 3/6] arm64: dts: ti: k3-j721e-main: Add serdes_ln_ctrl node to select SERDES lane mux

Kishon, Rob,

Quoted 49 lines · Kishon Vijay Abraham I

Hi Rob,

Quoted 36 lines · Rob Herring
Quoted 27 lines · Roger Quadros

From: Kishon Vijay Abraham I <[email protected]>

Add serdes_ln_ctrl node used for selecting SERDES lane mux.

---
  arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 27 ++++++++++++
  include/dt-bindings/mux/mux-j721e-wiz.h   | 53 +++++++++++++++++++++++
  2 files changed, 80 insertions(+)

create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h

arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +2 -0
index cbaadee5bfdc..c5d54af37e91 100644
@@ -5,6 +5,8 @@
   * Copyright (C) 2016-2019 Texas Instruments Incorporated - http://www.ti.com/
   */
  #include <dt-bindings/phy/phy.h>
+#include <dt-bindings/mux/mux.h>
+#include <dt-bindings/mux/mux-j721e-wiz.h>
 
  &cbass_main {
  	msmc_ram: sram@70000000 {

arch/arm64/boot/dts/ti/k3-j721e-main.dtsi line 25

Quoted 5 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +2 -0
@@ -19,6 +21,31 @@
  		};
  	};
 
+	scm_conf: scm-conf@100000 {
+		compatible = "syscon", "simple-mfd", "ti,j721e-system-controller";

Wrong ordering. Most significant first.

Quoted 9 lines

arch/arm64/boot/dts/ti/k3-j721e-main.dtsi line 31

Quoted 6 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +6 -0
+		reg = <0 0x00100000 0 0x1c000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x00100000 0x1c000>;
+
+		serdes_ln_ctrl: serdes-ln-ctrl@4080 {

Your syscon.yaml change is not valid if you have child nodes. Do a specific binding for this block.

Quoted 6 lines

Do you mean in addition to having platform specific binding for scm-conf, I need to have platform specific binding for serdes-ln-ctrl.

Since the driver doesn't do any platform specific stuff, the driver doesn't have to change. Is that correct?

Any resolution on this?

cheers,
-roger

Quoted 86 lines

Thanks
Kishon

Quoted 84 lines
Quoted 84 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +17 -0
+			compatible = "mmio-mux";
+			reg = <0x00004080 0x50>;
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
+					<0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
+					<0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
+					<0x40b0 0x3>, <0x40b4 0x3>, /* SERDES3 lane0/1 select */
+					<0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>;
+					/* SERDES4 lane0/1/2/3 select */
+			idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
+				      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
+				      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
+				      <MUX_IDLE_AS_IS>, <SERDES3_LANE1_USB3_0>,
+				      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
+		};
+	};
+
  	gic500: interrupt-controller@1800000 {
  		compatible = "arm,gic-v3";
  		#address-cells = <2>;
include/dt-bindings/mux/mux-j721e-wiz.h new file +53 -0
new file mode 100644
index 000000000000..fd1c4ea9fc7f
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides constants for J721E WIZ.
+ */
+
+#ifndef _DT_BINDINGS_J721E_WIZ
+#define _DT_BINDINGS_J721E_WIZ
+
+#define SERDES0_LANE0_QSGMII_LANE1	0x0
+#define SERDES0_LANE0_PCIE0_LANE0	0x1
+#define SERDES0_LANE0_USB3_0_SWAP	0x2
+
+#define SERDES0_LANE1_QSGMII_LANE2	0x0
+#define SERDES0_LANE1_PCIE0_LANE1	0x1
+#define SERDES0_LANE1_USB3_0		0x2
+
+#define SERDES1_LANE0_QSGMII_LANE3	0x0
+#define SERDES1_LANE0_PCIE1_LANE0	0x1
+#define SERDES1_LANE0_USB3_1_SWAP	0x2
+#define SERDES1_LANE0_SGMII_LANE0	0x3
+
+#define SERDES1_LANE1_QSGMII_LANE4	0x0
+#define SERDES1_LANE1_PCIE1_LANE1	0x1
+#define SERDES1_LANE1_USB3_1		0x2
+#define SERDES1_LANE1_SGMII_LANE1	0x3
+
+#define SERDES2_LANE0_PCIE2_LANE0	0x1
+#define SERDES2_LANE0_SGMII_LANE0	0x3
+#define SERDES2_LANE0_USB3_1_SWAP	0x2
+
+#define SERDES2_LANE1_PCIE2_LANE1	0x1
+#define SERDES2_LANE1_USB3_1		0x2
+#define SERDES2_LANE1_SGMII_LANE1	0x3
+
+#define SERDES3_LANE0_PCIE3_LANE0	0x1
+#define SERDES3_LANE0_USB3_0_SWAP	0x2
+
+#define SERDES3_LANE1_PCIE3_LANE1	0x1
+#define SERDES3_LANE1_USB3_0		0x2
+
+#define SERDES4_LANE0_EDP_LANE0		0x0
+#define SERDES4_LANE0_QSGMII_LANE5	0x2
+
+#define SERDES4_LANE1_EDP_LANE1		0x0
+#define SERDES4_LANE1_QSGMII_LANE6	0x2
+
+#define SERDES4_LANE2_EDP_LANE2		0x0
+#define SERDES4_LANE2_QSGMII_LANE7	0x2
+
+#define SERDES4_LANE3_EDP_LANE3		0x0
+#define SERDES4_LANE3_QSGMII_LANE8	0x2
+
+#endif /* _DT_BINDINGS_J721E_WIZ */
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
maintainer
#7 lore raw

Re: [PATCH v2 3/6] arm64: dts: ti: k3-j721e-main: Add serdes_ln_ctrl node to select SERDES lane mux

In reply to Kishon Vijay Abraham I
Quoted 47 lines · Kishon Vijay Abraham I

Hi Rob,

Quoted 43 lines · Rob Herring
Quoted 27 lines · Roger Quadros

From: Kishon Vijay Abraham I <[email protected]>

Add serdes_ln_ctrl node used for selecting SERDES lane mux.

---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 27 ++++++++++++
 include/dt-bindings/mux/mux-j721e-wiz.h   | 53 +++++++++++++++++++++++
 2 files changed, 80 insertions(+)
 create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +2 -0
index cbaadee5bfdc..c5d54af37e91 100644
@@ -5,6 +5,8 @@
  * Copyright (C) 2016-2019 Texas Instruments Incorporated - http://www.ti.com/
  */
 #include <dt-bindings/phy/phy.h>
+#include <dt-bindings/mux/mux.h>
+#include <dt-bindings/mux/mux-j721e-wiz.h>
 
 &cbass_main {
     msmc_ram: sram@70000000 {

arch/arm64/boot/dts/ti/k3-j721e-main.dtsi line 25

Quoted 5 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +2 -0
@@ -19,6 +21,31 @@
             };
     };
 
+    scm_conf: scm-conf@100000 {
+            compatible = "syscon", "simple-mfd", "ti,j721e-system-controller";

Wrong ordering. Most significant first.

Quoted 6 lines
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +6 -0
+            reg = <0 0x00100000 0 0x1c000>;
+            #address-cells = <1>;
+            #size-cells = <1>;
+            ranges = <0x0 0x0 0x00100000 0x1c000>;
+
+            serdes_ln_ctrl: serdes-ln-ctrl@4080 {
Quoted 5 lines
Quoted 2 lines

Your syscon.yaml change is not valid if you have child nodes. Do a specific binding for this block.

Do you mean in addition to having platform specific binding for scm-conf, I need to have platform specific binding for serdes-ln-ctrl.

I mean 'dt-bindings: syscon: Add TI's J721E specific compatible string'.

While not currently enforced because 'unevaluatedProperties: false' doesn't yet do anything, the intent with syscon.yaml is child nodes are not allowed. If you have child nodes, you need your own schema.

Rob

#8 lore raw

PATCH v2 4/6 arm64: dts: ti: k3-j721e-main.dtsi: Add USB to SERDES MUX

In reply to Roger Quadros

The USB controllers can be connected to one of the 2 SERDESes using a MUX. Add a MUX controller node fot that.

---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +7 -0
index c5d54af37e91..09b74f595f92 100644
@@ -44,6 +44,13 @@
 				      <MUX_IDLE_AS_IS>, <SERDES3_LANE1_USB3_0>,
 				      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
 		};
+
+		usb_serdes_mux: mux-controller@4000 {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x4000 0x8000000>, /* USB0 to SERDES0/3 mux */
+					<0x4010 0x8000000>; /* USB1 to SERDES1/2 mux */
+	    };
 	};
 
 	gic500: interrupt-controller@1800000 {
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
#9 lore raw

PATCH v2 5/6 arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0

In reply to Roger Quadros

USB0 supports super-speed mode on the EVM. Enable that. On the EVM, USB0 uses SERDES3 for super-speed lane.

Since USB0 is a type-C port, it needs to support lane swapping for cable flip support. This is provided using SERDES lane swap feature. Provide the Type-C cable orientation GPIO to the SERDES Wrapper driver.

---
 .../dts/ti/k3-j721e-common-proc-board.dts     | 32 +++++++++++++++++--
 1 file changed, 30 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts +30 -2
index 7a5c3d4adadd..f057322b8c11 100644
@@ -59,6 +59,7 @@
 	main_usbss0_pins_default: main_usbss0_pins_default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
+			J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
 		>;
 	};
 
@@ -310,16 +311,43 @@
 	status = "disabled";
 };
 
+&usb_serdes_mux {
+	idle-states = <1>, <0>; /* USB0 to SERDES3, USB1 to SERDES1 */
+};
+
+&serdes_ln_ctrl {
+	idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
+		      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
+		      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
+		      <SERDES3_LANE0_USB3_0_SWAP>, <SERDES3_LANE1_USB3_0>,
+		      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
+};
+
+&serdes_wiz3 {
+	typec-dir-gpios = <&main_gpio1 3 GPIO_ACTIVE_HIGH>;
+};
+
+&serdes3 {
+	serdes3_usb_link: link@0 {
+		reg = <0>;
+		cdns,num-lanes = <2>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_USB3>;
+		resets = <&serdes_wiz3 1>, <&serdes_wiz3 2>;
+	};
+};
+
 &usbss0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_usbss0_pins_default>;
-	ti,usb2-only;
 	ti,vbus-divider;
 };
 
 &usb0 {
 	dr_mode = "otg";
-	maximum-speed = "high-speed";
+	maximum-speed = "super-speed";
+	phys = <&serdes3_usb_link>;
+	phy-names = "cdns3,usb3-phy";
 };
 
 &usbss1 {
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
#10 lore raw

PATCH v2 6/6 arm64: dts: k3-j721e-proc-board: Add wait time for sampling Type-C DIR line

In reply to Roger Quadros

The Type-C compainon chip on the board needs ~133ms (tCCB_DEFAULT) to debounce the CC lines in order to detect attach and plug orientation and reflect the correct DIR status. [1]

On the EVM however we need to wait upto 700ms before sampling the Type-C DIR line else we can get incorrect direction state.

[1] http://www.ti.com/lit/ds/symlink/tusb321.pdf

---
 arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts +1 -0
index f057322b8c11..964a46e7af5e 100644
@@ -325,6 +325,7 @@
 
 &serdes_wiz3 {
 	typec-dir-gpios = <&main_gpio1 3 GPIO_ACTIVE_HIGH>;
+	typec-dir-debounce-ms = <700>;	/* TUSB321, tCCB_DEFAULT 133 ms */
 };
 
 &serdes3 {
Signature · 2 lines
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki