thermal: k3: Add support for bandgap sensors
Subsystems (3)
v6 cover thermal: k3: Add support for bandgap sensors
Add VTM thermal support. In the Voltage Thermal
Management Module(VTM), K3 AM654 supplies a voltage reference and a temperature sensor feature that are gathered in the band gap voltage and temperature sensor (VBGAPTS) module. The band gap provides current and voltage reference for its internal circuits and other analog IP blocks. The analog-to-digital converter (ADC) produces an output value that is proportional to the silicon temperature.
Add support for bandgap sensors. Currently reading temperatures is supported.
Changes in v6:
* Removed bunch of unused #defines and couple of redundant variables.
* Reordered patches a bit.
* Minor reordering in dt binding patch.
Changes in v5:
* Removed thermal work function which was unused.
* Removed unused preve_tenmp and a couple more struct variables.
* Removed couple of redundant header function include.
Changes in v4:
* Fixed comments from Daniel to remove trend function.
* Mostly cleaned up all the unused variables.
* Driver from bool to tristate.
Changes in v3:
* Fixed errors seen with:
dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/thermal/ti,am654-thermal.yaml
Changes in v2:
* Fixed yaml errors
* renamed am654-industrial-thermal.dtsi to k3-am654-industrial-thermal.dtsi to follow the convention for k3 family.
Keerthy (4):
dt-bindings: thermal: k3: Add VTM bindings documentation
thermal: k3: Add support for bandgap sensors
arm64: dts: ti: am65-wakeup: Add VTM node
arm64: dts: ti: am654: Add thermal zones
.../bindings/thermal/ti,am654-thermal.yaml | 56 ++++ arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 11 + .../dts/ti/k3-am654-industrial-thermal.dtsi | 45 +++ drivers/thermal/Kconfig | 10 + drivers/thermal/Makefile | 1 + drivers/thermal/k3_bandgap.c | 264 ++++++++++++++++++ 6 files changed, 387 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/ti,am654-thermal.yaml create mode 100644 arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi create mode 100644 drivers/thermal/k3_bandgap.c
Signature · 1 line
2.17.1
PATCH v6 1/4 dt-bindings: thermal: k3: Add VTM bindings documentation
Add VTM bindings documentation. In the Voltage Thermal Management Module(VTM), K3 AM654 supplies a voltage reference and a temperature sensor feature that are gathered in the band gap voltage and temperature sensor (VBGAPTS) module. The band gap provides current and voltage reference for its internal circuits and other analog IP blocks. The analog-to-digital converter (ADC) produces an output value that is proportional to the silicon temperature.
---
Changes in v6:
* Reordered the properties to match the order of definition.
.../bindings/thermal/ti,am654-thermal.yaml | 56 +++++++++++++++++++ 1 file changed, 56 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/ti,am654-thermal.yaml
Documentation/devicetree/bindings/thermal/ti,am654-thermal.yaml new file +56 -0
@@ -0,0 +1,56 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/thermal/ti,am654-thermal.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments AM654 VTM (DTS) binding + +maintainers: + - Keerthy <[email protected]> + +properties: + compatible: + const: ti,am654-vtm + + reg: + maxItems: 1 + + power-domains: + maxItems: 1 + + "#thermal-sensor-cells": + const: 1 + +required: + - compatible + - reg + - power-domains + - "#thermal-sensor-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/soc/ti,sci_pm_domain.h> + vtm: thermal@42050000 { + compatible = "ti,am654-vtm"; + reg = <0x0 0x42050000 0x0 0x25c>; + power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>; + #thermal-sensor-cells = <1>; + }; + + mpu0_thermal: mpu0_thermal { + polling-delay-passive = <250>; /* milliseconds */ + polling-delay = <500>; /* milliseconds */ + thermal-sensors = <&vtm0 0>; + + trips { + mpu0_crit: mpu0_crit { + temperature = <125000>; /* milliCelsius */ + hysteresis = <2000>; /* milliCelsius */ + type = "critical"; + }; + }; + }; +...
Signature · 1 line
2.17.1
Re: [PATCH v6 1/4] dt-bindings: thermal: k3: Add VTM bindings documentation
Quoted 10 lines · Keerthy
Add VTM bindings documentation. In the Voltage Thermal Management Module(VTM), K3 AM654 supplies a voltage reference and a temperature sensor feature that are gathered in the band gap voltage and temperature sensor (VBGAPTS) module. The band gap provides current and voltage reference for its internal circuits and other analog IP blocks. The analog-to-digital converter (ADC) produces an output value that is proportional to the silicon temperature.
Quoted 2 lines
Signed-off-by Keerthy <[email protected]>Reviewed-by Rob Herring <[email protected]>
Quoted 75 lines
---
Changes in v6:
* Reordered the properties to match the order of definition.
.../bindings/thermal/ti,am654-thermal.yaml | 56 +++++++++++++++++++ 1 file changed, 56 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/ti,am654-thermal.yamlDocumentation/devicetree/bindings/thermal/ti,am654-thermal.yaml new file +56
-1@@ -0,0 +1,56 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/thermal/ti,am654-thermal.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments AM654 VTM (DTS) binding + +maintainers: + - Keerthy <[email protected]> + +properties: + compatible: + const: ti,am654-vtm + + reg: + maxItems: 1 + + power-domains: + maxItems: 1 + + "#thermal-sensor-cells": + const: 1 + +required: + - compatible + - reg + - power-domains + - "#thermal-sensor-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/soc/ti,sci_pm_domain.h> + vtm: thermal@42050000 { + compatible = "ti,am654-vtm"; + reg = <0x0 0x42050000 0x0 0x25c>; + power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>; + #thermal-sensor-cells = <1>; + }; + + mpu0_thermal: mpu0_thermal { + polling-delay-passive = <250>; /* milliseconds */ + polling-delay = <500>; /* milliseconds */ + thermal-sensors = <&vtm0 0>; + + trips { + mpu0_crit: mpu0_crit { + temperature = <125000>; /* milliCelsius */ + hysteresis = <2000>; /* milliCelsius */ + type = "critical"; + }; + }; + }; +... --2.17.1
PATCH v6 2/4 thermal: k3: Add support for bandgap sensors
In reply to KeerthyAdd VTM thermal support. In the Voltage Thermal
Management Module(VTM), K3 AM654 supplies a voltage reference and a temperature sensor feature that are gathered in the band gap voltage and temperature sensor (VBGAPTS) module. The band gap provides current and voltage reference for its internal circuits and other analog IP blocks. The analog-to-digital converter (ADC) produces an output value that is proportional to the silicon temperature.
Currently reading temperatures only is supported. There are no active/passive cooling agent supported.
---
Changes in v6:
* Removed bunch of unused #defines and couple of redundant variables.
Changes in v5:
* Removed thermal work function which was unused.
* Removed unused preve_tenmp and a couple more struct variables.
* Removed couple of redundant header function include.
drivers/thermal/Kconfig | 10 ++ drivers/thermal/Makefile | 1 + drivers/thermal/k3_bandgap.c | 264 +++++++++++++++++++++++++++++++++++ 3 files changed, 275 insertions(+) create mode 100644 drivers/thermal/k3_bandgap.c
drivers/thermal/Kconfig +10 -0
@@ -251,6 +251,16 @@ config IMX_THERMAL cpufreq is used as the cooling device to throttle CPUs when the passive trip is crossed. +config K3_THERMAL + tristate "Texas Instruments K3 thermal support" + depends on ARCH_K3 || COMPILE_TEST + help + If you say yes here you get thermal support for the Texas Instruments + K3 SoC family. The current chip supported is: + - AM654 + + This includes temperature reading functionality. + config MAX77620_THERMAL tristate "Temperature sensor driver for Maxim MAX77620 PMIC" depends on MFD_MAX77620
drivers/thermal/Makefile +1 -0
@@ -28,6 +28,7 @@ thermal_sys-$(CONFIG_CLOCK_THERMAL) += clock_cooling.o # devfreq cooling thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o +obj-$(CONFIG_K3_THERMAL) += k3_bandgap.o # platform thermal drivers obj-y += broadcom/ obj-$(CONFIG_THERMAL_MMIO) += thermal_mmio.o
drivers/thermal/k3_bandgap.c new file +264 -0
264 lines not on this page · raw message
Signature · 1 line
2.17.1
Quoted 10 lines · Keerthy
Add VTM thermal support. In the Voltage Thermal
Management Module(VTM), K3 AM654 supplies a voltage reference and a temperature sensor feature that are gathered in the band gap voltage and temperature sensor (VBGAPTS) module. The band gap provides current and voltage reference for its internal circuits and other analog IP blocks. The analog-to-digital converter (ADC) produces an output value that is proportional to the silicon temperature.
Quoted 4 lines
Currently reading temperatures only is supported. There are no active/passive cooling agent supported.
Signed-off-by Keerthy <[email protected]>
Quoted 323 lines
---
Changes in v6:* Removed bunch of unused #defines and couple of redundant variables.
Changes in v5:
* Removed thermal work function which was unused.
* Removed unusedpreve_tenmpand a couple more struct variables.
* Removed couple of redundant header function include.drivers/thermal/Kconfig | 10 ++ drivers/thermal/Makefile | 1 + drivers/thermal/k3_bandgap.c | 264 +++++++++++++++++++++++++++++++++++ 3 files changed, 275 insertions(+) create mode 100644 drivers/thermal/k3_bandgap.cdrivers/thermal/Kconfig +10
-0@@ -251,6 +251,16 @@ config IMX_THERMAL cpufreq is used as the cooling device to throttle CPUs when the passive trip is crossed. +config K3_THERMAL + tristate "Texas Instruments K3 thermal support" + depends on ARCH_K3 || COMPILE_TEST + help + If you say yes here you get thermal support for the Texas Instruments + K3 SoC family. The current chip supported is: + - AM654 + + This includes temperature reading functionality. + config MAX77620_THERMAL tristate "Temperature sensor driver for Maxim MAX77620 PMIC" depends on MFD_MAX77620drivers/thermal/Makefile +1
-0@@ -28,6 +28,7 @@ thermal_sys-$(CONFIG_CLOCK_THERMAL) += clock_cooling.o # devfreq cooling thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o +obj-$(CONFIG_K3_THERMAL) += k3_bandgap.o # platform thermal drivers obj-y += broadcom/ obj-$(CONFIG_THERMAL_MMIO) += thermal_mmio.odrivers/thermal/k3_bandgap.c new file +264
-1@@ -0,0 +1,264 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* TI Bandgap temperature sensor driver for K3 SoC Family +* +* Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/ +*/ + +#include <linux/err.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/pm_runtime.h> +#include <linux/thermal.h> +#include <linux/types.h> + +#define K3_VTM_DEVINFO_PWR0_OFFSET 0x4 +#define K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK 0xf0 +#define K3_VTM_TMPSENS0_CTRL_OFFSET 0x80 +#define K3_VTM_REGS_PER_TS 0x10 +#define K3_VTM_TS_STAT_DTEMP_MASK 0x3ff +#define K3_VTM_TMPSENS_CTRL_CBIASSEL BIT(0) +#define K3_VTM_TMPSENS_CTRL_SOC BIT(5) +#define K3_VTM_TMPSENS_CTRL_CLRZ BIT(6) +#define K3_VTM_TMPSENS_CTRL_CLKON_REQ BIT(7) + +#define K3_VTM_ADC_BEGIN_VAL 540 +#define K3_VTM_ADC_END_VAL 944 + +static const int k3_adc_to_temp[] = { +-40000 ,-40000 ,-40000 ,-40000 ,-39800 ,-39400 ,-39000 ,-38600 ,-38200 , +-37800 ,-37400 ,-37000 ,-36600 ,-36200 ,-35800 ,-35300 ,-34700 ,-34200 , +-33800 ,-33400 ,-33000 ,-32600 ,-32200 ,-31800 ,-31400 ,-31000 ,-30600 , +-30200 ,-29800 ,-29400 ,-29000 ,-28600 ,-28200 ,-27700 ,-27100 ,-26600 , +-26200 ,-25800 ,-25400 ,-25000 ,-24600 ,-24200 ,-23800 ,-23400 ,-23000 , +-22600 ,-22200 ,-21800 ,-21400 ,-21000 ,-20500 ,-19900 ,-19400 ,-19000 , +-18600 ,-18200 ,-17800 ,-17400 ,-17000 ,-16600 ,-16200 ,-15800 ,-15400 , +-15000 ,-14600 ,-14200 ,-13800 ,-13400 ,-13000 ,-12500 ,-11900 ,-11400 , +-11000 ,-10600 ,-10200 ,-9800 ,-9400 ,-9000 ,-8600 ,-8200 ,-7800 ,-7400 , +-7000 ,-6600 ,-6200 ,-5800 ,-5400 ,-5000 ,-4500 ,-3900 ,-3400 ,-3000 , +-2600 ,-2200 ,-1800 ,-1400 ,-1000 ,-600 ,-200 ,200 ,600 ,1000 ,1400 , +1800 ,2200 ,2600 ,3000 ,3400 ,3900 ,4500 ,5000 ,5400 ,5800 ,6200 ,6600 , +7000 ,7400 ,7800 ,8200 ,8600 ,9000 ,9400 ,9800 ,10200 ,10600 ,11000 , +11400 ,11800 ,12200 ,12700 ,13300 ,13800 ,14200 ,14600 ,15000 ,15400 , +15800 ,16200 ,16600 ,17000 ,17400 ,17800 ,18200 ,18600 ,19000 ,19400 , +19800 ,20200 ,20600 ,21000 ,21400 ,21900 ,22500 ,23000 ,23400 ,23800 , +24200 ,24600 ,25000 ,25400 ,25800 ,26200 ,26600 ,27000 ,27400 ,27800 , +28200 ,28600 ,29000 ,29400 ,29800 ,30200 ,30600 ,31000 ,31400 ,31900 , +32500 ,33000 ,33400 ,33800 ,34200 ,34600 ,35000 ,35400 ,35800 ,36200 , +36600 ,37000 ,37400 ,37800 ,38200 ,38600 ,39000 ,39400 ,39800 ,40200 , +40600 ,41000 ,41400 ,41800 ,42200 ,42600 ,43100 ,43700 ,44200 ,44600 , +45000 ,45400 ,45800 ,46200 ,46600 ,47000 ,47400 ,47800 ,48200 ,48600 , +49000 ,49400 ,49800 ,50200 ,50600 ,51000 ,51400 ,51800 ,52200 ,52600 , +53000 ,53400 ,53800 ,54200 ,54600 ,55000 ,55400 ,55900 ,56500 ,57000 , +57400 ,57800 ,58200 ,58600 ,59000 ,59400 ,59800 ,60200 ,60600 ,61000 , +61400 ,61800 ,62200 ,62600 ,63000 ,63400 ,63800 ,64200 ,64600 ,65000 , +65400 ,65800 ,66200 ,66600 ,67000 ,67400 ,67800 ,68200 ,68600 ,69000 , +69400 ,69800 ,70200 ,70600 ,71000 ,71500 ,72100 ,72600 ,73000 ,73400 , +73800 ,74200 ,74600 ,75000 ,75400 ,75800 ,76200 ,76600 ,77000 ,77400 , +77800 ,78200 ,78600 ,79000 ,79400 ,79800 ,80200 ,80600 ,81000 ,81400 , +81800 ,82200 ,82600 ,83000 ,83400 ,83800 ,84200 ,84600 ,85000 ,85400 , +85800 ,86200 ,86600 ,87000 ,87400 ,87800 ,88200 ,88600 ,89000 ,89400 , +89800 ,90200 ,90600 ,91000 ,91400 ,91800 ,92200 ,92600 ,93000 ,93400 , +93800 ,94200 ,94600 ,95000 ,95400 ,95800 ,96200 ,96600 ,97000 ,97500 , +98100 ,98600 ,99000 ,99400 ,99800 ,100200 ,100600 ,101000 ,101400 , +101800 ,102200 ,102600 ,103000 ,103400 ,103800 ,104200 ,104600 ,105000 , +105400 ,105800 ,106200 ,106600 ,107000 ,107400 ,107800 ,108200 ,108600 , +109000 ,109400 ,109800 ,110200 ,110600 ,111000 ,111400 ,111800 ,112200 , +112600 ,113000 ,113400 ,113800 ,114200 ,114600 ,115000 ,115400 ,115800 , +116200 ,116600 ,117000 ,117400 ,117800 ,118200 ,118600 ,119000 ,119400 , +119800 ,120200 ,120600 ,121000 ,121400 ,121800 ,122200 ,122600 ,123000 , +123400 ,123800 ,124200 ,124600 ,124900 ,125000 , +}; + +struct k3_bandgap { +void __iomem *base; +const struct k3_bandgap_data *conf; +}; + +/* common data structures */ +struct k3_thermal_data { +struct thermal_zone_device *tzd; +struct k3_bandgap *bgp; +int sensor_id; +u32 ctrl_offset; +u32 stat_offset; +}; + +static unsigned int vtm_get_best_value (unsigned int s0,unsigned int s1, +unsigned int s2) +{ +int d01 =abs (s0 - s1); +int d02 =abs (s0 - s2); +int d12 =abs (s1 - s2); + +if (d01 <= d02 && d01 <= d12) +return (s0 + s1) /2 ; + +if (d02 <= d01 && d02 <= d12) +return (s0 + s2) /2 ; + +return (s1 + s2) /2 ; +} + +static int k3_bgp_read_temp (struct k3_thermal_data *devdata, +int *temp) +{ +struct k3_bandgap *bgp; +unsigned int dtemp, s0, s1, s2; + + bgp = devdata->bgp; + +/* +* Errata is applicable for am654 pg 1.0 silicon. There +* is a variation of the order for 8-10 degree centigrade. +* Work around that by getting the average of two closest +* readings out of three readings everytime we want to +* report temperatures. +* +* Errata workaround. +*/ + s0 =readl (bgp->base + devdata->stat_offset) & +K3_VTM_TS_STAT_DTEMP_MASK ; + s1 =readl (bgp->base + devdata->stat_offset) & +K3_VTM_TS_STAT_DTEMP_MASK ; + s2 =readl (bgp->base + devdata->stat_offset) & +K3_VTM_TS_STAT_DTEMP_MASK ; + dtemp =vtm_get_best_value (s0, s1, s2); + +if (dtemp <K3_VTM_ADC_BEGIN_VAL || dtemp >K3_VTM_ADC_END_VAL ) +return -EINVAL ; + + *temp = k3_adc_to_temp[dtemp -K3_VTM_ADC_BEGIN_VAL ]; + +return 0 ; +} + +static int k3_thermal_get_temp (void *devdata,int *temp) +{ +struct k3_thermal_data *data = devdata; +int ret =0 ; + + ret =k3_bgp_read_temp (data, temp); +if (ret) +return ret; + +return ret; +} + +static const struct thermal_zone_of_device_ops k3_of_thermal_ops = { + .get_temp = k3_thermal_get_temp, +}; + +static const struct of_device_id of_k3_bandgap_match[]; + +static int k3_bandgap_probe (struct platform_device *pdev) +{ +int ret =0 , cnt, val, id; +struct resource *res; +struct device *dev = &pdev->dev; +struct k3_bandgap *bgp; +struct k3_thermal_data *data; + +if (ARRAY_SIZE (k3_adc_to_temp) != (K3_VTM_ADC_END_VAL +1 - +K3_VTM_ADC_BEGIN_VAL )) +return -EINVAL ; + + bgp =devm_kzalloc (&pdev->dev,sizeof (*bgp),GFP_KERNEL ); +if (!bgp) +return -ENOMEM ; + + res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + bgp->base =devm_ioremap_resource (dev, res); +if (IS_ERR (bgp->base)) +return PTR_ERR (bgp->base); + +pm_runtime_enable (dev); + ret =pm_runtime_get_sync (dev); +if (ret <0 ) { +pm_runtime_put_noidle (dev); +pm_runtime_disable (dev); +return ret; + } + +/* Get the sensor count in the VTM */ + val =readl (bgp->base +K3_VTM_DEVINFO_PWR0_OFFSET ); + cnt = val &K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ; + cnt >>=__ffs (K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ); + + data =devm_kcalloc (dev, cnt,sizeof (*data),GFP_KERNEL ); +if (!data) { + ret = -ENOMEM ; + goto err_alloc; + } + +/* Register the thermal sensors */ +for (id =0 ; id < cnt; id++) { + data[id].sensor_id = id; + data[id].bgp = bgp; + data[id].ctrl_offset =K3_VTM_TMPSENS0_CTRL_OFFSET + + id *K3_VTM_REGS_PER_TS ; + data[id].stat_offset = data[id].ctrl_offset +0x8 ; + + val =readl (data[id].bgp->base + data[id].ctrl_offset); + val |= (K3_VTM_TMPSENS_CTRL_SOC | +K3_VTM_TMPSENS_CTRL_CLRZ | +K3_VTM_TMPSENS_CTRL_CLKON_REQ ); + val &= ~K3_VTM_TMPSENS_CTRL_CBIASSEL ; +writel (val, data[id].bgp->base + data[id].ctrl_offset); + + data[id].tzd = +devm_thermal_zone_of_sensor_register (dev, id, + &data[id], + &k3_of_thermal_ops); +if (IS_ERR (data[id].tzd)) { +dev_err (dev,"thermal zone device is NULL\n" ); + ret =PTR_ERR (data[id].tzd); + goto err_alloc; + } + } + +platform_set_drvdata (pdev, bgp); + +return 0 ; + +err_alloc: +pm_runtime_put_sync (dev); +pm_runtime_disable (dev); + +return ret; +} + +static int k3_bandgap_remove (struct platform_device *pdev) +{ +pm_runtime_put_sync (&pdev->dev); +pm_runtime_disable (&pdev->dev); + +return 0 ; +} + +static const struct of_device_id of_k3_bandgap_match[] = { + { + .compatible ="ti,am654-vtm" , + }, + {/* sentinel */ }, +}; +MODULE_DEVICE_TABLE (of, of_k3_bandgap_match); + +static struct platform_driver k3_bandgap_sensor_driver = { + .probe = k3_bandgap_probe, + .remove = k3_bandgap_remove, + .driver = { + .name ="k3-soc-thermal" , + .of_match_table = of_k3_bandgap_match, + }, +}; + +module_platform_driver (k3_bandgap_sensor_driver); + +MODULE_DESCRIPTION ("K3 bandgap temperature sensor driver" ); +MODULE_LICENSE ("GPL v2" ); +MODULE_AUTHOR ("J Keerthy <[email protected]>" ); --2.17.1
PATCH v6 3/4 arm64: dts: ti: am65-wakeup: Add VTM node
In reply to KeerthyVTM stands for voltage and thermal management.
--- arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi +7 -0
@@ -89,4 +89,11 @@ clocks = <&k3_clks 59 0>; clock-names = "gpio"; }; + + wkup_vtm0: thermal@42050000 { + compatible = "ti,am654-vtm"; + reg = <0x42050000 0x25c>; + power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>; + #thermal-sensor-cells = <1>; + }; };
Signature · 1 line
2.17.1
Re: [PATCH v6 3/4] arm64: dts: ti: am65-wakeup: Add VTM node
Quoted 4 lines · Keerthy
VTM stands for voltage and thermal management.
Signed-off-by Keerthy <[email protected]>
Quoted 23 lines
--- arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 7 +++++++ 1 file changed, 7 insertions(+)arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi +7
-1@@ -89,4 +89,11 @@ clocks = <&k3_clks 59 0>; clock-names = "gpio"; }; + + wkup_vtm0: thermal@42050000 { + compatible = "ti,am654-vtm"; + reg = <0x42050000 0x25c>; + power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>; + #thermal-sensor-cells = <1>; + }; }; --2.17.1
PATCH v6 4/4 arm64: dts: ti: am654: Add thermal zones
In reply to KeerthyThe am654 SoC has three thermal zones namely MPU0, MPU1 and MCU zones.
--- arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 4 ++ .../dts/ti/k3-am654-industrial-thermal.dtsi | 45 +++++++++++++++++++ 2 files changed, 49 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi +4 -0
@@ -96,4 +96,8 @@ power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>; #thermal-sensor-cells = <1>; }; + + thermal_zones: thermal-zones { + #include "k3-am654-industrial-thermal.dtsi" + }; };
arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi new file +45 -0
45 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [PATCH v6 4/4] arm64: dts: ti: am654: Add thermal zones
Quoted 5 lines · Keerthy
The am654 SoC has three thermal zones namely MPU0, MPU1 and MCU zones.
Signed-off-by Keerthy <[email protected]>
Quoted 73 lines
--- arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 4 ++ .../dts/ti/k3-am654-industrial-thermal.dtsi | 45 +++++++++++++++++++ 2 files changed, 49 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsiarch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi +4
-0@@ -96,4 +96,8 @@ power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>; #thermal-sensor-cells = <1>; }; + + thermal_zones: thermal-zones { + #include "k3-am654-industrial-thermal.dtsi" + }; };arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi new file +45
-1@@ -0,0 +1,45 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include <dt-bindings/thermal/thermal.h> + +mpu0_thermal: mpu0_thermal { + polling-delay-passive = <250>; /* milliseconds */ + polling-delay = <500>; /* milliseconds */ + thermal-sensors = <&wkup_vtm0 0>; + + trips { + mpu0_crit: mpu0_crit { + temperature = <125000>; /* milliCelsius */ + hysteresis = <2000>; /* milliCelsius */ + type = "critical"; + }; + }; +}; + +mpu1_thermal: mpu1_thermal { + polling-delay-passive = <250>; /* milliseconds */ + polling-delay = <500>; /* milliseconds */ + thermal-sensors = <&wkup_vtm0 1>; + + trips { + mpu1_crit: mpu1_crit { + temperature = <125000>; /* milliCelsius */ + hysteresis = <2000>; /* milliCelsius */ + type = "critical"; + }; + }; +}; + +mcu_thermal: mcu_thermal { + polling-delay-passive = <250>; /* milliseconds */ + polling-delay = <500>; /* milliseconds */ + thermal-sensors = <&wkup_vtm0 2>; + + trips { + mcu_crit: mcu_crit { + temperature = <125000>; /* milliCelsius */ + hysteresis = <2000>; /* milliCelsius */ + type = "critical"; + }; + }; +}; --2.17.1
Hi Keerthy,
Quoted 11 lines · Keerthy
Add VTM thermal support. In the Voltage Thermal
Management Module(VTM), K3 AM654 supplies a voltage reference and a temperature sensor feature that are gathered in the band gap voltage and temperature sensor (VBGAPTS) module. The band gap provides current and voltage reference for its internal circuits and other analog IP blocks. The analog-to-digital converter (ADC) produces an output value that is proportional to the silicon temperature.Add support for bandgap sensors. Currently reading temperatures is supported.
How do you want to proceed? Shall I take patches 1 & 2 ?
Quoted 46 lines
Changes in v6:
* Removed bunch of unused #defines and couple of redundant variables.
* Reordered patches a bit.
* Minor reordering in dt binding patch.Changes in v5:
* Removed thermal work function which was unused.
* Removed unusedpreve_tenmpand a couple more struct variables.
* Removed couple of redundant header function include.Changes in v4:
* Fixed comments from Daniel to remove trend function.
* Mostly cleaned up all the unused variables.
* Driver from bool to tristate.Changes in v3:
* Fixed errors seen with:
dt_binding_checkDT_SCHEMA_FILES=Documentation/devicetree/bindings/thermal/ti,am654-thermal.yamlChanges in v2:
* Fixed yaml errors
* renamedam654-industrial-thermal.dtsitok3-am654-industrial-thermal.dtsito follow the convention for k3 family.Keerthy (4):
dt-bindings: thermal: k3: Add VTM bindings documentation
thermal: k3: Add support for bandgap sensors
arm64: dts: ti: am65-wakeup: Add VTM node
arm64: dts: ti: am654: Add thermal zones.../bindings/thermal/ti,am654-thermal.yaml | 56 ++++ arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 11 + .../dts/ti/k3-am654-industrial-thermal.dtsi | 45 +++ drivers/thermal/Kconfig | 10 + drivers/thermal/Makefile | 1 + drivers/thermal/k3_bandgap.c | 264 ++++++++++++++++++ 6 files changed, 387 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/ti,am654-thermal.yaml create mode 100644 arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi create mode 100644 drivers/thermal/k3_bandgap.c
Signature · 5 lines
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook | <http://twitter.com/#!/linaroorg> Twitter | <http://www.linaro.org/linaro-blog/> Blog
Quoted 13 lines · Daniel Lezcano
Hi Keerthy,
Quoted 9 lines · Keerthy
Add VTM thermal support. In the Voltage Thermal
Management Module(VTM), K3 AM654 supplies a voltage reference and a temperature sensor feature that are gathered in the band gap voltage and temperature sensor (VBGAPTS) module. The band gap provides current and voltage reference for its internal circuits and other analog IP blocks. The analog-to-digital converter (ADC) produces an output value that is proportional to the silicon temperature.
Quoted 4 lines
Quoted 2 lines
Add support for bandgap sensors. Currently reading temperatures is supported.
How do you want to proceed? Shall I take patches 1 & 2 ?
+Tero
Hi Tero,
Can you pull 3 & 4? Or Daniel can take all 4?
- Keerthy
Quoted 37 lines
Quoted 37 lines
Changes in v6:
* Removed bunch of unused #defines and couple of redundant variables.
* Reordered patches a bit.
* Minor reordering in dt binding patch.Changes in v5:
* Removed thermal work function which was unused.
* Removed unusedpreve_tenmpand a couple more struct variables.
* Removed couple of redundant header function include.Changes in v4:
* Fixed comments from Daniel to remove trend function.
* Mostly cleaned up all the unused variables.
* Driver from bool to tristate.Changes in v3:
* Fixed errors seen with:
dt_binding_checkDT_SCHEMA_FILES=Documentation/devicetree/bindings/thermal/ti,am654-thermal.yamlChanges in v2:
* Fixed yaml errors
* renamedam654-industrial-thermal.dtsitok3-am654-industrial-thermal.dtsito follow the convention for k3 family.Keerthy (4):
dt-bindings: thermal: k3: Add VTM bindings documentation
thermal: k3: Add support for bandgap sensors
arm64: dts: ti: am65-wakeup: Add VTM node
arm64: dts: ti: am654: Add thermal zones
Quoted 13 lines
Quoted 11 lines
.../bindings/thermal/ti,am654-thermal.yaml | 56 ++++ arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 11 + .../dts/ti/k3-am654-industrial-thermal.dtsi | 45 +++ drivers/thermal/Kconfig | 10 + drivers/thermal/Makefile | 1 + drivers/thermal/k3_bandgap.c | 264 ++++++++++++++++++ 6 files changed, 387 insertions(+)create mode 100644
Documentation/devicetree/bindings/thermal/ti,am654-thermal.yamlcreate mode 100644arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsicreate mode 100644drivers/thermal/k3_bandgap.c
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 19 lines · KEERTHY
Quoted 16 lines · Daniel Lezcano
Hi Keerthy,
Quoted 11 lines · Keerthy
Add VTM thermal support. In the Voltage Thermal
Management Module(VTM), K3 AM654 supplies a voltage reference and a temperature sensor feature that are gathered in the band gap voltage and temperature sensor (VBGAPTS) module. The band gap provides current and voltage reference for its internal circuits and other analog IP blocks. The analog-to-digital converter (ADC) produces an output value that is proportional to the silicon temperature.Add support for bandgap sensors. Currently reading temperatures is supported.
Quoted 7 lines
Quoted 1 line
How do you want to proceed? Shall I take patches 1 & 2 ?
+Tero
Hi Tero,
Can you pull 3 & 4? Or Daniel can take all 4?
Let me pull the DT patches, that way we avoid any conflicts in the arm64/dts tree. There has been quite a bit of traffic on that front lately and we did mess up something with the current merge window already.
I believe you are picking the driver side changes to 5.8?
-Tero
Quoted 54 lines
- Keerthy
Quoted 51 lines
Quoted 49 lines
Changes in v6:
* Removed bunch of unused #defines and couple of redundant variables.
* Reordered patches a bit.
* Minor reordering in dt binding patch.Changes in v5:
* Removed thermal work function which was unused.
* Removed unusedpreve_tenmpand a couple more struct variables.
* Removed couple of redundant header function include.Changes in v4:
* Fixed comments from Daniel to remove trend function.
* Mostly cleaned up all the unused variables.
* Driver from bool to tristate.Changes in v3:
* Fixed errors seen with:
dt_binding_checkDT_SCHEMA_FILES=Documentation/devicetree/bindings/thermal/ti,am654-thermal.yamlChanges in v2:
* Fixed yaml errors
* renamedam654-industrial-thermal.dtsitok3-am654-industrial-thermal.dtsito follow the convention for k3 family.Keerthy (4):
dt-bindings: thermal: k3: Add VTM bindings documentation
thermal: k3: Add support for bandgap sensors
arm64: dts: ti: am65-wakeup: Add VTM node
arm64: dts: ti: am654: Add thermal zones.../bindings/thermal/ti,am654-thermal.yaml | 56 ++++ arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 11 + .../dts/ti/k3-am654-industrial-thermal.dtsi | 45 +++ drivers/thermal/Kconfig | 10 + drivers/thermal/Makefile | 1 + drivers/thermal/k3_bandgap.c | 264 ++++++++++++++++++
6 files changed, 387 insertions(+)create mode 100644
Documentation/devicetree/bindings/thermal/ti,am654-thermal.yamlcreate mode 100644arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsicreate mode 100644drivers/thermal/k3_bandgap.c
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Quoted 27 lines · Tero Kristo
Quoted 26 lines · KEERTHY
Quoted 14 lines · Daniel Lezcano
Hi Keerthy,
Quoted 10 lines · Keerthy
Add VTM thermal support. In the Voltage Thermal Management Module(VTM), K3 AM654 supplies a voltage reference and a temperature sensor feature that are gathered in the band
gap voltage and temperature sensor (VBGAPTS) module. The band gap provides current and voltage reference for its internal circuits and other analog IP blocks. The analog-to-digital converter (ADC) produces an output value that is proportional to the silicon temperature.Quoted 4 lines
Quoted 2 lines
Add support for bandgap sensors. Currently reading temperatures is supported.
How do you want to proceed? Shall I take patches 1 & 2 ?
+Tero
Hi Tero,
Quoted 7 lines
Quoted 1 line
Can you pull 3 & 4? Or Daniel can take all 4?
Let me pull the DT patches, that way we avoid any conflicts in the arm64/dts tree. There has been quite a bit of traffic on that front lately and we did mess up something with the current merge window already.
I believe you are picking the driver side changes to 5.8?
Applied patches 1 & 2
Thanks
-- Daniel
Signature · 5 lines
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook | <http://twitter.com/#!/linaroorg> Twitter | <http://www.linaro.org/linaro-blog/> Blog
Tero Kristo
AppliedQuoted 30 lines · Daniel Lezcano
Quoted 29 lines · Tero Kristo
Quoted 27 lines · KEERTHY
Quoted 14 lines · Daniel Lezcano
Hi Keerthy,
Quoted 10 lines · Keerthy
Add VTM thermal support. In the Voltage Thermal Management Module(VTM), K3 AM654 supplies a voltage reference and a temperature sensor feature that are gathered in the band
gap voltage and temperature sensor (VBGAPTS) module. The band gap provides current and voltage reference for its internal circuits and other analog IP blocks. The analog-to-digital converter (ADC) produces an output value that is proportional to the silicon temperature.Quoted 4 lines
Quoted 2 lines
Add support for bandgap sensors. Currently reading temperatures is supported.
How do you want to proceed? Shall I take patches 1 & 2 ?
+Tero
Hi Tero,
Can you pull 3 & 4? Or Daniel can take all 4?
Quoted 7 lines
Quoted 5 lines
Let me pull the DT patches, that way we avoid any conflicts in the arm64/dts tree. There has been quite a bit of traffic on that front lately and we did mess up something with the current merge window already.
I believe you are picking the driver side changes to 5.8?
Applied patches 1 & 2
Queued patches 3 & 4 towards 5.8, thanks.
-Tero
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel