Skip to contentSkip to conversation

ARM: dts: stm32: add seeed studio odyssey-stm32mp157c board

PATCH Superseded Marcin Sloniewski 2 participants 3 messages Jun 30, 2020 – Jul 1, 2020

Subsystems (2)

v2 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 ARM: dts: stm32: add seeed studio odyssey-stm32mp157c board

This commit adds device tree files supporting
SBC from Seeed Studio based on STM32MP157C.

This works with generic stm32mp1 config.
Right now only booting from SD card is supported.

---

Changes in v2:
- removed st,adc_usb_pd from config since that
adc connection is non-existent which caused
warning or hang during boot

 arch/arm/dts/Makefile                         |   3 +-
 .../dts/odyssey-stm32mp157c-som-u-boot.dtsi   | 134 +++++++
 arch/arm/dts/odyssey-stm32mp157c-som.dtsi     | 364 ++++++++++++++++++
 arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi  |  64 +++
 arch/arm/dts/odyssey-stm32mp157c.dts          | 161 ++++++++
 5 files changed, 725 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi
 create mode 100644 arch/arm/dts/odyssey-stm32mp157c-som.dtsi
 create mode 100644 arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi
 create mode 100644 arch/arm/dts/odyssey-stm32mp157c.dts
arch/arm/dts/Makefile +2 -1
index 9900b44274..dd617c7188 100644
@@ -918,7 +918,8 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb \
 	stm32mp15xx-dhcom-pdk2.dtb \
-	stm32mp15xx-dhcor-avenger96.dtb
+	stm32mp15xx-dhcor-avenger96.dtb \
+	odyssey-stm32mp157c.dtb
 
 dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb
 dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi new file +134 -0

134 lines not on this page · raw message

arch/arm/dts/odyssey-stm32mp157c-som.dtsi new file +364 -0

364 lines not on this page · raw message

arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi new file +64 -0

64 lines not on this page · raw message

arch/arm/dts/odyssey-stm32mp157c.dts new file +161 -0

161 lines not on this page · raw message

Signature · 1 line
2.26.2
#1 lore raw

PATCH v2 1/1 ARM: dts: stm32: add seeed studio odyssey-stm32mp157c board

Hi Marcin,

Quoted 33 lines

From: Marcin Sloniewski <[email protected]>
Sent: mardi 30 juin 2020 22:02

This commit adds device tree files supporting SBC from Seeed Studio based on STM32MP157C.

This works with generic stm32mp1 config.
Right now only booting from SD card is supported.

---

Changes in v2:
- removed st,adc_usb_pd from config since that
adc connection is non-existent which caused
warning or hang during boot

 arch/arm/dts/Makefile                         |   3 +-
 .../dts/odyssey-stm32mp157c-som-u-boot.dtsi   | 134 +++++++
 arch/arm/dts/odyssey-stm32mp157c-som.dtsi     | 364 ++++++++++++++++++
 arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi  |  64 +++
 arch/arm/dts/odyssey-stm32mp157c.dts          | 161 ++++++++
 5 files changed, 725 insertions(+), 1 deletion(-)  create mode 100644
arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi
 create mode 100644 arch/arm/dts/odyssey-stm32mp157c-som.dtsi
 create mode 100644 arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi
 create mode 100644 arch/arm/dts/odyssey-stm32mp157c.dts
arch/arm/dts/Makefile index renamed from arch/arm/dts/Makefile +0 -0

9900b44274..dd617c7188 100644

arch/arm/dts/Makefile dtb-$(CONFIG_STM32MP15x) += \ · line 922

Quoted 6 lines
arch/arm/dts/Makefile +2 -1
@@ -918,7 +918,8 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb \
 	stm32mp15xx-dhcom-pdk2.dtb \
-	stm32mp15xx-dhcor-avenger96.dtb
+	stm32mp15xx-dhcor-avenger96.dtb \
+	odyssey-stm32mp157c.dtb

Minor remarks, I try to follow alphabetics order when it is possible, so :

dtb-$(CONFIG_STM32MP15x) += \

+	odyssey-stm32mp157c.dtb \
	stm32mp157a-dk1.dtb \
Quoted 108 lines
arch/arm/dts/Makefile +0 -0
 dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-

board.dtb
dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \ diff --git
a/arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi b/arch/arm/dts/odyssey- stm32mp157c-som-u-boot.dtsi
new file mode 100644
index 0000000000..cf08efae09

arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi new file +98 -0
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp15-u-boot.dtsi"
+#include "stm32mp15-ddr3-1x4Gb-1066-binG.dtsi"
+
+/ {
+	config {
+		u-boot,boot-led = "heartbeat";
+	};
+};
+
+&clk_hse {
+	st,digbypass;
+};
+
+&i2c2 {
+	u-boot,dm-pre-reloc;
+};
+
+&i2c2_pins_a {
+	u-boot,dm-pre-reloc;
+	pins {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&pmic {
+	u-boot,dm-pre-reloc;
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSE
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_DISABLED
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4R
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSE
+	>;

arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi line 108

Quoted 10 lines
arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi new file +10 -0
+
+	/* VCO = 1300.0 MHz => P = 650 (CPU) */
+	pll1: st,pll at 0 {
+		compatible = "st,stm32mp1-pll";
+		reg = <0>;
+		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
+		frac = < 0x800 >;
+		u-boot,dm-pre-reloc;
+	};
+

For information pll1 configuration will be comes optional with
http://patchwork.ozlabs.org/project/uboot/list/?series=179056

Quoted 459 lines
arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi new file +26 -0
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll at 1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
+		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+		frac = < 0x1400 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll at 2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
+		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+		frac = < 0x1a04 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
+	pll4: st,pll at 3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
+		cfg = < 3 98 5 7 7 PQR(1,1,1) >;
+		u-boot,dm-pre-reloc;
+	};
+};
arch/arm/dts/odyssey- renamed from arch/arm/dts/odyssey-stm32mp157c-som.dtsi +0 -0

stm32mp157c-som.dtsi
new file mode 100644
index 0000000000..855de9523c

arch/arm/dts/odyssey-stm32mp157c-som.dtsi new file +252 -0
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+
+	model = "Seeed Studio Odyssey-STM32MP157C SOM";
+	compatible = "seeed,odyssey-stm32mp157c-som", "st,stm32mp157";
+
+	memory at c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2 at 10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0 at 10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1 at 10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer at 10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram at 30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram at 38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+
+		gpu_reserved: gpu at d4000000 {
+			reg = <0xd4000000 0x4000000>;
+			no-map;
+		};
+
+		optee at de000000 {
+			reg = <0xde000000 0x02000000>;
+			no-map;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		blue {
+			label = "heartbeat";
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+};
+
+&gpu {
+	contiguous-area = <&gpu_reserved>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_pins_sleep_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic at 33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v2_hdmi: ldo6 {
+				regulator-name = "v1v2_hdmi";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			 bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			 };
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>,

<&vdev0vring0>,

arch/arm/dts/odyssey-stm32mp157c-som.dtsi new file +112 -0
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	broken-cd;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm1_pins_a>;
+		pinctrl-1 = <&pwm1_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 0 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm3_pins_a>;
+		pinctrl-1 = <&pwm3_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm4_pins_a &pwm4_pins_b>;
+		pinctrl-1 = <&pwm4_sleep_pins_a &pwm4_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 3 {
+		status = "okay";
+	};
+};
+
+&timers5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 4 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	timer at 5 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-1 = <&pwm12_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 11 {
+		status = "okay";
+	};
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};
arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi new file +54 -0
new file mode 100644
index 0000000000..12073b3616
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+ #include "odyssey-stm32mp157c-som-u-boot.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &sdmmc1;
+		usb0 = &usbotg_hs;
+	};
+	config {
+		u-boot,boot-led = "heartbeat";
+		u-boot,error-led = "error";
+	};
+	led {
+		red {
+			label = "error";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			status = "okay";
+		};
+	};
+};
+
+&adc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {

arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi line 64

Quoted 10 lines
arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi new file +10 -0
+		u-boot,dm-pre-reloc;
+		/* pull-up on rx to avoid floating level */
+		bias-pull-up;
+	};
+};
+
+&usbotg_hs {
+	u-boot,force-b-session-valid;
+	hnp-srp-disable;
+};

I think this part can be removed
u-boot,force-b-session-valid => activated to force peripheral mode, used in DK1/DK2 only because we are using USB TypeC controller STUSB1600 for USB cable detection hnp-srp-disable => activated to avoid issue in HOST mode, and USTOTG is configured in PERIPHERAL after.

Quoted 169 lines
arch/arm/dts/odyssey- renamed from arch/arm/dts/odyssey-stm32mp157c.dts +0 -0

stm32mp157c.dts
new file mode 100644
index 0000000000..949081ca84

arch/arm/dts/odyssey-stm32mp157c.dts new file +161 -1
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+/dts-v1/;
+
+#include "odyssey-stm32mp157c-som.dtsi"
+
+/ {
+
+	model = "Seeed Studio Odyssey-STM32MP157C Board";
+	compatible = "seeed,odyssey-stm32mp157c", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+		blue {
+			label = "heartbeat";
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_a>, <&adc12_usb_cc_pins_a>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdd>;
+	vref-supply = <&vrefbuf>;
+	status = "disabled";
+	adc1: adc at 0 {
+		/*
+		 * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19.
+		 * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
+		 * 5 * (56 + 47kOhms) * 5pF => 2.5us.
+		 * Use arbitrary margin here (e.g. 5us).
+		 */
+		st,min-sample-time-nsecs = <5000>;
+		/* AIN connector, USB Type-C CC1 & CC2 */
+		st,adc-channels = <0 1 6 13 18 19>;
+		status = "okay";
+	};
+	adc2: adc at 100 {
+		/* AIN connector, USB Type-C CC1 & CC2 */
+		st,adc-channels = <0 1 2 6 18 19>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+};
+
+&cec {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cec_pins_b>;
+	pinctrl-1 = <&cec_pins_sleep_b>;
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy at 0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gpu {
+	contiguous-area = <&gpu_reserved>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_pins_sleep_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2s2 {
+	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "i2sclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2s2_pins_a>;
+	pinctrl-1 = <&i2s2_pins_sleep_a>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
+
--
Quoted 1 line

2.26.2

If you correct the minor remarks

Thanks

Patrick

#2 lore raw

PATCH v2 1/1 ARM: dts: stm32: add seeed studio odyssey-stm32mp157c board

Hi,

Quoted 821 lines

From: Patrick DELAUNAY
Sent: mercredi 1 juillet 2020 11:59

Hi Marcin,

Quoted 33 lines

From: Marcin Sloniewski <[email protected]>
Sent: mardi 30 juin 2020 22:02

This commit adds device tree files supporting SBC from Seeed Studio based on STM32MP157C.

This works with generic stm32mp1 config.
Right now only booting from SD card is supported.

---

Changes in v2:
- removed st,adc_usb_pd from config since that
adc connection is non-existent which caused
warning or hang during boot

 arch/arm/dts/Makefile                         |   3 +-
 .../dts/odyssey-stm32mp157c-som-u-boot.dtsi   | 134 +++++++
 arch/arm/dts/odyssey-stm32mp157c-som.dtsi     | 364 ++++++++++++++++++
 arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi  |  64 +++
 arch/arm/dts/odyssey-stm32mp157c.dts          | 161 ++++++++
 5 files changed, 725 insertions(+), 1 deletion(-)  create mode 100644
arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi
 create mode 100644 arch/arm/dts/odyssey-stm32mp157c-som.dtsi
 create mode 100644 arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi
 create mode 100644 arch/arm/dts/odyssey-stm32mp157c.dts
arch/arm/dts/Makefile index renamed from arch/arm/dts/Makefile +0 -0

9900b44274..dd617c7188 100644

arch/arm/dts/Makefile dtb-$(CONFIG_STM32MP15x) += \ · line 922

Quoted 6 lines
arch/arm/dts/Makefile +2 -1
@@ -918,7 +918,8 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb \
 	stm32mp15xx-dhcom-pdk2.dtb \
-	stm32mp15xx-dhcor-avenger96.dtb
+	stm32mp15xx-dhcor-avenger96.dtb \
+	odyssey-stm32mp157c.dtb

Minor remarks, I try to follow alphabetics order when it is possible, so :

dtb-$(CONFIG_STM32MP15x) += \

(quoted diff) +1 -0
+	odyssey-stm32mp157c.dtb \
	stm32mp157a-dk1.dtb \

arch/arm/dts/Makefile dtb-$(CONFIG_STM32MP15x) += \ · line 923

Quoted 1 line
arch/arm/dts/Makefile +0 -0
 dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-

base-

Quoted 106 lines

board.dtb
dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \ diff
--git a/arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi b/arch/arm/dts/odyssey- stm32mp157c-som-u-boot.dtsi new file mode 100644 index 0000000000..cf08efae09

arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi new file +98 -0
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp15-u-boot.dtsi"
+#include "stm32mp15-ddr3-1x4Gb-1066-binG.dtsi"
+
+/ {
+	config {
+		u-boot,boot-led = "heartbeat";
+	};
+};
+
+&clk_hse {
+	st,digbypass;
+};
+
+&i2c2 {
+	u-boot,dm-pre-reloc;
+};
+
+&i2c2_pins_a {
+	u-boot,dm-pre-reloc;
+	pins {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&pmic {
+	u-boot,dm-pre-reloc;
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSE
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_DISABLED
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4R
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSE
+	>;

arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi line 108

Quoted 10 lines
arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi new file +10 -0
+
+	/* VCO = 1300.0 MHz => P = 650 (CPU) */
+	pll1: st,pll at 0 {
+		compatible = "st,stm32mp1-pll";
+		reg = <0>;
+		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
+		frac = < 0x800 >;
+		u-boot,dm-pre-reloc;
+	};
+

For information pll1 configuration will be comes optional with
http://patchwork.ozlabs.org/project/uboot/list/?series=179056

Quoted 458 lines
arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi new file +26 -0
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll at 1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
+		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+		frac = < 0x1400 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll at 2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
+		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+		frac = < 0x1a04 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
+	pll4: st,pll at 3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
+		cfg = < 3 98 5 7 7 PQR(1,1,1) >;
+		u-boot,dm-pre-reloc;
+	};
+};
(quoted diff) +0 -0

b/arch/arm/dts/odyssey- stm32mp157c-som.dtsi new file mode 100644 index 0000000000..855de9523c

arch/arm/dts/odyssey-stm32mp157c-som.dtsi new file +252 -0
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+
+	model = "Seeed Studio Odyssey-STM32MP157C SOM";
+	compatible = "seeed,odyssey-stm32mp157c-som", "st,stm32mp157";
+
+	memory at c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2 at 10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0 at 10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1 at 10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer at 10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram at 30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram at 38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+
+		gpu_reserved: gpu at d4000000 {
+			reg = <0xd4000000 0x4000000>;
+			no-map;
+		};
+
+		optee at de000000 {
+			reg = <0xde000000 0x02000000>;
+			no-map;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		blue {
+			label = "heartbeat";
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+};
+
+&gpu {
+	contiguous-area = <&gpu_reserved>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_pins_sleep_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic at 33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v2_hdmi: ldo6 {
+				regulator-name = "v1v2_hdmi";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			 bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			 };
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>,

<&vdev0vring0>,

arch/arm/dts/odyssey-stm32mp157c-som.dtsi new file +112 -0
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	broken-cd;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm1_pins_a>;
+		pinctrl-1 = <&pwm1_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 0 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm3_pins_a>;
+		pinctrl-1 = <&pwm3_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm4_pins_a &pwm4_pins_b>;
+		pinctrl-1 = <&pwm4_sleep_pins_a &pwm4_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 3 {
+		status = "okay";
+	};
+};
+
+&timers5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 4 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	timer at 5 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-1 = <&pwm12_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 11 {
+		status = "okay";
+	};
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};
arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi new file +54 -0
new file mode 100644
index 0000000000..12073b3616
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+ #include "odyssey-stm32mp157c-som-u-boot.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &sdmmc1;
+		usb0 = &usbotg_hs;
+	};
+	config {
+		u-boot,boot-led = "heartbeat";
+		u-boot,error-led = "error";
+	};
+	led {
+		red {
+			label = "error";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			status = "okay";
+		};
+	};
+};
+
+&adc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {

arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi line 64

Quoted 10 lines
arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi new file +10 -0
+		u-boot,dm-pre-reloc;
+		/* pull-up on rx to avoid floating level */
+		bias-pull-up;
+	};
+};
+
+&usbotg_hs {
+	u-boot,force-b-session-valid;
+	hnp-srp-disable;
+};

I think this part can be removed
u-boot,force-b-session-valid => activated to force peripheral mode, used in DK1/DK2 only because we are using USB TypeC controller STUSB1600 for USB cable detection hnp-srp-disable => activated to avoid issue in HOST mode, and USTOTG is configured in PERIPHERAL after.

Quoted 168 lines
(quoted diff) +0 -0

b/arch/arm/dts/odyssey- stm32mp157c.dts new file mode 100644 index 0000000000..949081ca84

arch/arm/dts/odyssey-stm32mp157c.dts new file +161 -1
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+/dts-v1/;
+
+#include "odyssey-stm32mp157c-som.dtsi"
+
+/ {
+
+	model = "Seeed Studio Odyssey-STM32MP157C Board";
+	compatible = "seeed,odyssey-stm32mp157c", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+		blue {
+			label = "heartbeat";
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_a>, <&adc12_usb_cc_pins_a>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdd>;
+	vref-supply = <&vrefbuf>;
+	status = "disabled";
+	adc1: adc at 0 {
+		/*
+		 * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19.
+		 * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
+		 * 5 * (56 + 47kOhms) * 5pF => 2.5us.
+		 * Use arbitrary margin here (e.g. 5us).
+		 */
+		st,min-sample-time-nsecs = <5000>;
+		/* AIN connector, USB Type-C CC1 & CC2 */
+		st,adc-channels = <0 1 6 13 18 19>;
+		status = "okay";
+	};
+	adc2: adc at 100 {
+		/* AIN connector, USB Type-C CC1 & CC2 */
+		st,adc-channels = <0 1 2 6 18 19>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+};
+
+&cec {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cec_pins_b>;
+	pinctrl-1 = <&cec_pins_sleep_b>;
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy at 0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gpu {
+	contiguous-area = <&gpu_reserved>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_pins_sleep_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2s2 {
+	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "i2sclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2s2_pins_a>;
+	pinctrl-1 = <&i2s2_pins_sleep_a>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
+
--
Quoted 1 line

2.26.2

If you correct the minor remarks

Quoted 6 lines

Thanks

Patrick

An other minor remarks: need to update a board MAINTAINERS or it is in a other serie ...

board/seeed/odyssey-stm32mp157c/MAINTAINERS ?

regards

Patrick