Skip to contentSkip to conversation

ARM: dts: stm32: add seeed studio odyssey-stm32mp157c board

PATCH Superseded Marcin Sloniewski 2 participants 2 messages Jul 1, 2020

Subsystems (2)

v3 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 ARM: dts: stm32: add seeed studio odyssey-stm32mp157c board

This commit adds device tree files supporting
SBC from Seeed Studio based on STM32MP157C.

This works with generic stm32mp1 config.
Right now only booting from SD card is supported.

---

Changes in v3:
- changed name of dts files from odyssey-stm32mp157c... to stm32mp157c-odyssey...
- removed usbotg node config
- add new board in dts/Makefile in alphabetical order

Changes in v2:
- removed st,adc_usb_pd from config since that
adc connection is non-existent which caused
warning or hang during boot

 arch/arm/dts/Makefile                         |   1 +
 .../dts/stm32mp157c-odyssey-som-u-boot.dtsi   | 134 +++++++
 arch/arm/dts/stm32mp157c-odyssey-som.dtsi     | 364 ++++++++++++++++++
 arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi  |  60 +++
 arch/arm/dts/stm32mp157c-odyssey.dts          | 161 ++++++++
 5 files changed, 720 insertions(+)
 create mode 100644 arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-odyssey-som.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-odyssey.dts
arch/arm/dts/Makefile +1 -0
index 9900b44274..af94ed5aef 100644
@@ -917,6 +917,7 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb \
+	stm32mp157c-odyssey.dtb \
 	stm32mp15xx-dhcom-pdk2.dtb \
 	stm32mp15xx-dhcor-avenger96.dtb
 
arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi new file +134 -0

134 lines not on this page · raw message

arch/arm/dts/stm32mp157c-odyssey-som.dtsi new file +364 -0

364 lines not on this page · raw message

arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi new file +60 -0

60 lines not on this page · raw message

arch/arm/dts/stm32mp157c-odyssey.dts new file +161 -0

161 lines not on this page · raw message

Signature · 1 line
2.26.2
#1 lore raw

PATCH v3 1/1 ARM: dts: stm32: add seeed studio odyssey-stm32mp157c board

Hi Marcin,

Sorry I found an other delta with DK2 on uart.

Quoted 615 lines

From: Marcin Sloniewski <[email protected]>
Sent: mercredi 1 juillet 2020 17:03

This commit adds device tree files supporting SBC from Seeed Studio based on STM32MP157C.

This works with generic stm32mp1 config.
Right now only booting from SD card is supported.

---

Changes in v3:
- changed name of dts files from odyssey-stm32mp157c... to stm32mp157c-odyssey...
- removed usbotg node config
- add new board in dts/Makefile in alphabetical order

Changes in v2:
- removed st,adc_usb_pd from config since that
adc connection is non-existent which caused
warning or hang during boot

 arch/arm/dts/Makefile                         |   1 +
 .../dts/stm32mp157c-odyssey-som-u-boot.dtsi   | 134 +++++++
 arch/arm/dts/stm32mp157c-odyssey-som.dtsi     | 364 ++++++++++++++++++
 arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi  |  60 +++
 arch/arm/dts/stm32mp157c-odyssey.dts          | 161 ++++++++
 5 files changed, 720 insertions(+)
 create mode 100644 arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-odyssey-som.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-odyssey.dts
arch/arm/dts/Makefile index renamed from arch/arm/dts/Makefile +0 -0

9900b44274..af94ed5aef 100644

arch/arm/dts/Makefile +1 -0
@@ -917,6 +917,7 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb \
+	stm32mp157c-odyssey.dtb \
 	stm32mp15xx-dhcom-pdk2.dtb \
 	stm32mp15xx-dhcor-avenger96.dtb
 
arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi new file +134 -0
new file mode 100644
index 0000000000..cf08efae09
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp15-u-boot.dtsi"
+#include "stm32mp15-ddr3-1x4Gb-1066-binG.dtsi"
+
+/ {
+	config {
+		u-boot,boot-led = "heartbeat";
+	};
+};
+
+&clk_hse {
+	st,digbypass;
+};
+
+&i2c2 {
+	u-boot,dm-pre-reloc;
+};
+
+&i2c2_pins_a {
+	u-boot,dm-pre-reloc;
+	pins {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&pmic {
+	u-boot,dm-pre-reloc;
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSE
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_DISABLED
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4R
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSE
+	>;
+
+	/* VCO = 1300.0 MHz => P = 650 (CPU) */
+	pll1: st,pll at 0 {
+		compatible = "st,stm32mp1-pll";
+		reg = <0>;
+		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
+		frac = < 0x800 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll at 1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
+		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+		frac = < 0x1400 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll at 2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
+		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+		frac = < 0x1a04 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
+	pll4: st,pll at 3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
+		cfg = < 3 98 5 7 7 PQR(1,1,1) >;
+		u-boot,dm-pre-reloc;
+	};
+};
arch/arm/dts/stm32mp157c-odyssey-som.dtsi new file +252 -0
new file mode 100644
index 0000000000..855de9523c
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+
+	model = "Seeed Studio Odyssey-STM32MP157C SOM";
+	compatible = "seeed,odyssey-stm32mp157c-som", "st,stm32mp157";
+
+	memory at c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2 at 10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0 at 10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1 at 10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer at 10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram at 30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram at 38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+
+		gpu_reserved: gpu at d4000000 {
+			reg = <0xd4000000 0x4000000>;
+			no-map;
+		};
+
+		optee at de000000 {
+			reg = <0xde000000 0x02000000>;
+			no-map;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		blue {
+			label = "heartbeat";
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+};
+
+&gpu {
+	contiguous-area = <&gpu_reserved>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_pins_sleep_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic at 33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v2_hdmi: ldo6 {
+				regulator-name = "v1v2_hdmi";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			 bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			 };
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>,

<&vdev0vring0>,

arch/arm/dts/stm32mp157c-odyssey-som.dtsi new file +112 -0
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	broken-cd;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm1_pins_a>;
+		pinctrl-1 = <&pwm1_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 0 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm3_pins_a>;
+		pinctrl-1 = <&pwm3_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm4_pins_a &pwm4_pins_b>;
+		pinctrl-1 = <&pwm4_sleep_pins_a &pwm4_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 3 {
+		status = "okay";
+	};
+};
+
+&timers5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 4 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	timer at 5 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-1 = <&pwm12_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer at 11 {
+		status = "okay";
+	};
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};
arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi new file +49 -0
new file mode 100644
index 0000000000..606c74fb53
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+ #include "stm32mp157c-odyssey-som-u-boot.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &sdmmc1;
+		usb0 = &usbotg_hs;
+	};
+	config {
+		u-boot,boot-led = "heartbeat";
+		u-boot,error-led = "error";
+	};
+	led {
+		red {
+			label = "error";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			status = "okay";
+		};
+	};
+};
+
+&adc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {

arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi line 59

Quoted 10 lines
arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi new file +10 -0
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {
+		u-boot,dm-pre-reloc;
+		/* pull-up on rx to avoid floating level */
+		bias-pull-up;
+	};
+};

On DK2 the pul-up on rx was needed on SOC side as not physically present on the BOARD (pull up was expected done by embedded STLINK but only done when STLINK was really powered-up)

On the odyssey schematic
https://github.com/SeeedDocument/ODYSSEY-STM32MP157C/raw/master/Hardware/Seeed%20NPi%20-%20STM32MP157C%20v1.0_191212.pdf

DEBUG have already pull-up on RX line (R91 = 10K)

=> you can remove it in the DT:

+ pins2 {
+ u-boot,dm-pre-reloc;
+ };

Quoted 170 lines
arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi new file +1 -0
+
arch/arm/dts/stm32mp157c- renamed from arch/arm/dts/stm32mp157c-odyssey.dts +0 -0

odyssey.dts
new file mode 100644
index 0000000000..1ea340d9a8

arch/arm/dts/stm32mp157c-odyssey.dts new file +161 -1
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>
+*/
+
+/dts-v1/;
+
+#include "stm32mp157c-odyssey-som.dtsi"
+
+/ {
+
+	model = "Seeed Studio Odyssey-STM32MP157C Board";
+	compatible = "seeed,odyssey-stm32mp157c", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+		blue {
+			label = "heartbeat";
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_a>, <&adc12_usb_cc_pins_a>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdd>;
+	vref-supply = <&vrefbuf>;
+	status = "disabled";
+	adc1: adc at 0 {
+		/*
+		 * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19.
+		 * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
+		 * 5 * (56 + 47kOhms) * 5pF => 2.5us.
+		 * Use arbitrary margin here (e.g. 5us).
+		 */
+		st,min-sample-time-nsecs = <5000>;
+		/* AIN connector, USB Type-C CC1 & CC2 */
+		st,adc-channels = <0 1 6 13 18 19>;
+		status = "okay";
+	};
+	adc2: adc at 100 {
+		/* AIN connector, USB Type-C CC1 & CC2 */
+		st,adc-channels = <0 1 2 6 18 19>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+};
+
+&cec {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cec_pins_b>;
+	pinctrl-1 = <&cec_pins_sleep_b>;
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy at 0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gpu {
+	contiguous-area = <&gpu_reserved>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_pins_sleep_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2s2 {
+	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "i2sclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2s2_pins_a>;
+	pinctrl-1 = <&i2s2_pins_sleep_a>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
+
--
Quoted 1 line

2.26.2

Except this minor remark:

Thanks

Patrick